Parts Manual fo
r
E
21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
PUSH MODELS PROPELLED
MODELS
216517B P215517HC
2167517BV P216517B
R215517HC P2167517BV
R2167517BV P2167517BVE
P217017BV
P217017BV
RP215517HC
RP2167517BV
RP217017BV
RP2167517BVE
RP217017BVE
WP2167517BV
WP216517BV
WRP216517BE
FRP2167517BV
EP2167517BV
EP217017BV
ERP2167517BV
ERP217017BV
EFRP2167517BV
WRPS216517B
WRPS216517BE
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 4,
McDonough, GA, 30253 U.S.A.
1/16/2006
Manual No. 7006136
TP 400-5002-4-WB-N
s
PAGE GROUP
4
8
12
14
16
18
20
22
24
28
30
32
34
36
38
40
42
44
46
48
50
52
HANDLES & CONTROLS
CUTTING DECK, BLADES
FRONT WHEEL BRACKET
SWIVEL CASTER ASSEMBLY
REAR WHEEL BRACKETS, LATCHES
FRONT WHEELS
FRONT WHEELS - SWIVEL MODEL
REAR WHEELS
DRIVE SYSTEM SELF-PROPELLED PT.1
TRANSMISSION (DIFFERENTIAL)
THROTTLE CONTROLS
KIT, MUFFLER DEFLECTOR
ENGINE SPECIFICATIONS
SIDE CHUTE, ADAPTER
GRASS BAG ACCESSORY
DECALS PT. 1
DECALS PT. 2
SNAPPERIZER ACCESSORY
THATCHERIZER ACCESSORY
RECYCLING KITS ACCESSORY
ELECTRIC START COMPONENTS
WIRING SCHEMATIC
Table Of Content
SERIES 17
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
3
TP 400-5002-4-WB-N
HANDLES & CONTROLS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
4
SERIES 17
HANDLES & CONTROLS
p
y
Part No Descri
1 7074254 1 HANDLE, Upper Was 72931 (used on Push
-- 7074254 1 HANDLE, Upper used on Self-Propelled
2 7036350 1 HANDLE, Middle- 1990 used on All
3 7046502 1 HANDLE, Lower Left Hand used on All
4 7035342 1 HANDLE, Lower Right Hand used on All
5 7047011 1 BAIL, Blade Control used on All
6 7033904 1 CLIP, Blade Control used on 2002 Models & Earlier
-- 7034872 1 CLIP, Blade Control used on 2003 Models & Later
7 7072933 1 CABLE, Blade Control (49-1/4” long) used on 2002 Models & Earlier
-- 7074868 1 CABLE, Blade Control (46-15/16” long) used on 2003 Models & Later
-- 7074830 1 CABLE, Blade Control (49” long) used on Honda 2003 Models &
8 7032826 1 HANDLE, Wheel Drive used on Self-Propelled
9 7014307 1 GRIP, Wheel Drive Handle used on Self-Propelled
-- 7029775 1 GRIP, Wheel Drive Handle used on European Models
10 7072932 1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
11 7012121 1 COVER, Vinyl used on Self-Propelled
12 7012122 1 SPRING, Clutch used on Self-Propelled
13 7038478 1 SECTOR, Speed used on all other Self-Propelled
14 7024641 3 WIRE TIE, 1.29” Long (Black) used on Self-Propelled
15 7012093 1 SPRING, Speed Control used on Self-Propelled
16 7090188 1 WASHER, 3/8” Flat used on Self-Propelled
17 7023801 1 GRIP, Speed Control Handle used on all other Self-Propelled
18 7032830 1 ANCHOR, Speed Control used on all other Self-Propelled
19 7032408 1 GUIDE, Lower V-Belt used on Self-Propelled
20 7023790 1 ROD, Transfer used on Self-Propelled
20A 7051698 1 ASSEMBLY, Transfer Rod used on European Models
21 7010937 1 CLIP, Transfer Rod 1/4” used on Self-Propelled
22 7090895 1 TEE-NUT, 5/16-18 used on Self-Propelled
23 7012114 1 BUSHING, Differential used on Self-Propelled
24 7090595 1 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
25 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
26 7090799 1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026 (used on All)
27 7091601 10 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070 (used on All)
28 7091606 1 NUT, 5/16-24 Hex Center Lock GR5 Was 91074 (used on All)
29 7023813 1 CLIP, Cable/Wiring used on All
30 7091740 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 Was 91189 (used on All)
31 7035744 4 T-KNOB, 5/16-18 (BLACK) used on All
tionItem Qt
Note
Models)
Later
models
models
models
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
5
TP 400-5002-4-WB-N
HANDLES & CONTROLS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
6
SERIES 17
HANDLES & CONTROLS
p
y
Part No Descri
32 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 used on All
33 7090053 3 WASHER, 1/4” Internal Tooth Lock Was 91023 (used on All)
34 7091576 3 NUT, 1/4-20 Hex GR5 or B Was 91100 (used on All)
35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on All
36 7014343 4 BUSHING used on All
37 7023792 1 PIN, 1/4” x 1-1/2” (for clutch handle) used on Self-Propelled
38 7091020 1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
39 7024211 1 DECAL, Blade Control (Left Hand Side) used on all (except Euro)
-- 7029782 1 DECAL, Blade Control (Left Hand Side) used on European
-- 7029785 1 DECAL, Handle International Warning used on European
40 7026141 1 GUIDE, Rope used on All
41 7075634 1 FOAM GRIP, .84 I.D. x 11” long Was 73115
-- 7075634 1 FOAM GRIP, .84 I.D. x 12” long
42 7024087 1 DECAL, Speed Select used on Self-Propelled (except
-- 7029783 1 DECAL, Speed Select (Euro) used on Self-Propelled (Euro)
43 7023153 1 CLAMP, Casing used on All
44 7090391 4 WASHER, 5/16” Internal Tooth Lock used on All
45 7090545 1 SCREW, 5/16-24 x 1-1/2” Round Hd. Machine, GR5 used on All
46 7022779 1 GUIDE, Rope used on All
47 7074255 1 LEVER, Speed Control used on Self-Propelled
48 7046465 1 GUIDE, Rope used on Self-Propelled
49 7076978 1 NUT, 1/4-20 Hex GR5 or B used on Self-Propelled
50 7012080 1 CABLE-TIE, 7” used on Self-Propelled
52 7023154 1 SCREW, #10-32 x 5/8” Hex Head Self-Tap used on All
51 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Head Cap, GR5 used on Self-Propelled
53 7024649 1 WIRE TIE, 11” Long (Black) used on Self-Propelled
-- 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on Self-Propelled
54 7026219 1 CLAMP, 7/8” Double Cable used on Self-Propelled
56 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5" used on Swivel Wheel
tionItem Qt
Note
Euro)
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
7
TP 400-5002-4-WB-N
CUTTING DECK, BLADES
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
8
SERIES 17
CUTTING DECK, BLADES
p
y
Part No Descri
1 7057663 1 DECK, 21” Mower (“HV” deck w/decals)
-- 7058540 1 DECK, 21” Mower (Baffle Type deck w/decals) used on “FRP” & “EFRP” Air
-- 7057884 1 DECK, 21” Mower (“M” deck w/decals)
-- 7074949 1 DECK, 21” Mower (Swivvel wheel "M" deck w/o decals)
2 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR5 Was 90585
3 7090731 10 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
4 7091169 1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5
5 7090324 3 SCREW, 3/8-16 x 1” Self-Tap (engine mounting screws)
6 7046780 2 PLUG, Hole
7 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
8 7090702 1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock used on Euro models
9 7013320 1 BUSHING used on Euro models
10 7033863 1 COVER, Belt used on Euro models
11 7031961 2 WASHER, 7/16” Flat used on Euro models
12 7090483 1 SCREW, 3/8-24 x 1-3/4 Hex Head Cap GR5
13 7012063 2 WASHER, 3/8” I.D. Cone
14 7019795 1 BLADE, Cutter (European) used on Euro models
14A 7017168 1 BLADE, Cutter (Mulching)
14B 7026691 1 BLADE, Cutter (Standard Lift)
14C 7026407 1 BLADE, 21” Ninja (Quad Edge)
15 7015626 1 HUB, Blade Drive 25mm used on Briggs Models
-- 7012927 1 HUB, Blade Drive 7/8” used on Honda Models
16 7015894 1 KEY, Woodruff # 605 used on Briggs Models
-- 7091214 1 KEY, Hi-Pro #HP506 used on Briggs Models
-- 7010783 1 KEY, Woodruff #505 Hi-Pro used on Honda Models
17 7090201 1 SCREW, 5/16-18 x 5/16” Hex Socket Set
18 7015780 1 PULLEY, Engine (25mm I.D. x 2-1/8” O.D.) used on Briggs Models
-- 7021764 1 PULLEY, Engine (7/8” I.D. x 2-1/8” O.D.) used on Honda Models
19 7031961 1 WASHER, 7/16” Flat
20 7041400 1 WELDMENT, Fender used on Euro models
21 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001 (only one shown)
22 7011791 2 RETAINER, 5/16” Bolt (only one shown)
23 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070
-- 7060785 1 KIT, Air Lift (Includes 4 items below)
24 7032558 2 LIFT, Air
25 7090391 4 WASHER, 5/16” Internal Tooth Lock
26 7091297 4 NUT, 5/16-24 Hex, GR5 Was 90223
tionItem Qt
Note
Models only
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
9
TP 400-5002-4-WB-N
CUTTING DECK, BLADES
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
10
SERIES 17
CUTTING DECK, BLADES
p
y
Part No Descri
27 7090228 4 SCREW, 5/16-24 x 21/32” Machine
28 7090951 2 NUT, 5/16-18 Hex Center Lock
29 7029193 1 DECAL, Front Baffle
30 7072426 1 BAFFLE, Front used on “FRP” & “EFRP” Air
31 7036463 1 DECAL, Front Baffle
32 7090316 2 BOLT, 5/16-18 x 3/4” Carriage, GR5
33 7090189 2 WASHER, 5/16” Internal/External Tooth Lock
34 7024085 2 WINGNUT, 5/16-18 Nyloc
35 7091076 1 WASHER, 5/16” Flat
36 7044770 1 SPACER, 1/16” Thick, Blade Hub
37 7074568 1 BAFFLE, Belt
38 7046471 3 PLUG, 5/16” Square Hole used on Push only
39 7045264 3 PLUG, 5/16” Round Hole Qty 3 on Push; Qty 2 on Self-
40 7091122 4 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
41 7046720 1 DECAL, Warning Chute/Deflector
tionItem Qt
Note
Models only
Propelled
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
11
TP 400-5002-4-WB-N
FRONT WHEEL BRACKET
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
12
SERIES 17
FRONT WHEEL BRACKET
p
y
Part No Descri
1 7051886 1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &
-- 7051885 1 ASSEMBLY, Left Wheel Arm (Consists of items 2, 3, 4, 5B &
2 7015761 2 BOLT, 5/16-18 Hex Washer Face Shoulder
3 7012325 2 LATCH, Height
4 7027702 2 GRIP, Latch
5A 7031017 1 ARM, Right Wheel (Round Hole)
5B 7031016 1 ARM, Left Wheel (Square Hole) not shown
6 7011791 2 RETAINER, 5/16” Bolt (Black)
7 7091601 2 NUT, 5/16-18 Hex Flange Lock Was 91070
8 7074702 1 WELDMENT, Front Wheel Bracket Was 41770, Used on 2002
-- 7074702 1 WELDMENT, Front Wheel Bracket used on 2003 Model Year and
9 7021119 1 AXLE
tionItem Qt
Note
6)
6)
Model Year and Earlier
Later
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
13
TP 400-5002-4-WB-N
SWIVEL CASTER ASSEMBLY
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
14
SERIES 17
SWIVEL CASTER ASSEMBLY
p
y
Part No Descri
1 7057782 1 WELDMENT, Front Bracket
2 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Cap
3 7090372 1 NUT, 1/4-20 Hex Lock
4 7072244 1 BRACKET, Swivel Lock
5 7046668 1 SPRING, Torsion
6 7090505 1 BOLT, 1/4-20 x 2” Hex
7 7027344 4 WASHER, 41/64” Flat Was 15992
8 7046628 4 BUSHING, 5/8” Nylon
9 7013864 2 LUBE FITTING, Straight (press-fit for .187 dia. Hole)
10 7076978 1 NUT, 1/4-20 Hex Lock
11 7014106 2 PIN, 1/4 x 1-3/4” Roll
12 7072229 1 WELDMENT, L.H. Swivel Bracket
7072230 1 WELDMENT, R.H. Swivel Bracket Was 57789 (Not Shown)
13 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5”
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
15
TP 400-5002-4-WB-N
REAR WHEEL BRACKETS, LATCHES
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
16
SERIES 17
REAR WHEEL BRACKETS, LATCHES
p
y
Part No Descri
1 7012312 2 BALL BEARING, 9/16” I.D.
2 7091012 3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)
3 7035717 2 LATCH, Height Adjusting (Long)
4 7091576 1 NUT, 1/4-20 Hex Was 90063
5 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070
6 7054228 1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
7 7054229 1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
8 7054246 1 ASSEMBLY, Wheel Arm (Right Rear) Was 54230 (Self-Propelled
9 7054247 1 ASSEMBLY, Wheel Arm (Left Rear) Was 54231 (Self-Propelled
10 7033776 1 ARM, Round Axle End, Right Rear (Round hole) used on Push models
11 7033775 1 ARM, Square Axle End, Left Rear (Square hole) used on Push models
12 7032722 1 ARM, Wheel, Right Rear used on Self-Propelled models
13 7032723 1 ARM, Wheel, Left Rear used on Self-Propelled models
14 7011078 2 BOLT, 5/16-18 x 1” Shoulder
15 7011791 2 RETAINER, 5/16” Bolt
16 7027702 2 GRIP, Latch
17 7033494 1 BRACKET, Right Rear Wheel
18 7033495 1 BRACKET, Left Rear Wheel
19 7021119 1 AXLE Rear axle on Push Models;
20 7035741 1 GUARD, Rear Foot used on Push models
21 7029008 1 GUARD, Rear Foot used on Self-Propelled models
-- 7017010 1 GUARD, Rear Foot used on Euro Self-Propelled
22 7023791 1 RING, Split (Black) used on Self-Propelled models
23 7012616 1 SUPPORT, Foot Guard used on Self-Propelled models
24 7091604 1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 Was 90005 (used on Self-
25 7090053 1 WASHER, 1/4” Internal Tooth Lock Was 91023
26 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
tionItem Qt
Note
items 3, 10, 14, 15 & 16)
items 3, 11, 14, 15 & 16)
models)(Incl. 1, 2, 3, 12, 14, 15
& 16)
Models)(Includes 1, 2, 3, 13, 15,
& 16)
Front axle on All Models
(except European)
models
Propelled models)
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
17
TP 400-5002-4-WB-N
FRONT WHEELS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
18
SERIES 17
FRONT WHEELS
p
y
Part No Descri
1 7022374 2 WHEEL, 8 x 1.75 Plastic used on 2002 Model Year and
2 7029010 2 WHEEL, 8 x 1.75 Plastic used on 2003 Model Year and
3 7090377 2 NUT, 7/16-20 Hex Center Lock Jam (thin)
4 7012309 2 BUSHING, Axle
5 7031961 6 WASHER, 7/16 x 1” O.D. Flat Qty. of (2) for Push; Qty. of (1)
6 7017829 2 PLUG, Wheel
tionItem Qt
Note
Earlier
Later
for Self-Propelled Models
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
19
TP 400-5002-4-WB-N
FRONT WHEELS - SWIVEL MODEL
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
20
SERIES 17
FRONT WHEELS - SWIVEL MODEL
p
y
Part No Descri
1 7072243 2 PIN, Wheel - Stepped .435 DIA x 2.725 Long
2 7046708 2 PIN, Swivel Wheel Lock
3 7046990 2 WHEEL, 8 x 1.75 Plastic - Gray
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
21
TP 400-5002-4-WB-N
REAR WHEELS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
22
SERIES 17
REAR WHEELS
p
y
Part No Descri
1A 7035739 2 WHEEL, 10 x 1.75” Plastic (Push Models) used on 2002 Model Year and
1B 7074924 2 WHEEL, 10 x 1.75” Plastic (Push Models) used on 2003 Model Year and
2A 7035740 2 WHEEL, 10 x 1.75” Plastic (Self-Propelled Models) used on 2002 Model Year and
2B 7029011 2 WHEEL, 10 x 1.75” Plastic (Self-Propelled Models) used on 2003 Model Year and
3 7090377 2 NUT, 7/16-20 Hex Center Lock Jam
4 7012309 2 BUSHING, Axle
5 7031961 4 WASHER, 7/16 x 1” O.D. Flat
6 7017829 2 PLUG, Wheel
tionItem Qt
Note
Earlier
Later
Earlier
Later
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
23
TP 400-5002-4-WB-N
DRIVE SYSTEM SELF-PROPELLED PT.1
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
24
SERIES 17
DRIVE SYSTEM SELF-PROPELLED PT.1
p
y
Part No Descri
1 7012354 1 BELT, Poly-Vee
2 7034179 1 LINK, Differential
-- 7051921 ASSEMBLY, Clutch Idler (includes items 3 thru 7)
3 7032832 1 ARM, Clutch Idler
4 7012124 1 PULLEY, Idler
5 7091025 1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
6 7090303 1 NUT, 1/4-28 Hex Top Lock
7 7012117 2 BUSHING, 3/8” Plastic
8 7072284 1 SHAFT, Hex Drive
9 7024521 1 PULLEY, Poly-V, 2” O.D. Non Commercial Models
10 7012316 1 WASHER, 3/8” Flat
11 7012126 1 SPRING, Torsion
12 7012111 1 STUD, Idler (3/8-24 thread)
13 7031873 1 HOLDER, Bearing (Inner Half)
14 7028014 1 BEARING, Ball, .38 I.D. Spherical O.D.
15 7011025 1 O-RING
16 7090289 1 NUT, 3/8-24 Hex Center Lock GR5 or B
17 7031809 1 HOLDER, Bearing (Outer Half)
18 7010937 1 CLIP, 1/4” Right Arc (Transfer Rod)
19 7023790 1 ROD, Transfer used on Non-Euro models
20 7046784 1 BELT, Engine Drive 3L (Stretch) used on Self-Propelled
21 7035477 1 PLATE, Thrust
22 7010746 2 RING, 5/8” External Retaining used on Self-Propelled
23 7026693 1 BALL BEARING, 3/4” I.D. used on Self-Propelled
24 7090981 4 SCREW, #10-32 x 1/4” Self-Tap Machine
25 7032664 1 SHIELD, Hex Shaft used on Self-Propelled Euro only
-- 7051698 1 ASSEMBLY, Transfer Rod (Incl. items 26, 27 & 28) used on Self-Propelled Euro only
26 7015753 1 BALL JOINT, 1/4-28 used on Self-Propelled Euro only
27 7090095 1 NUT, 1/4-28 Hex GR5 used on Self-Propelled Euro only
28 7015752 1 LINK, Transfer used on Self-Propelled Euro only
29 7010121 1 WASHER, 3/4” Shim
30 7090390 3 WASHER, 3/8” Internal Tooth Lock
31 7090122 1 WASHER, 3/8” Flat
32 7091630 3 NUT, 3/8-24 Hex, GR B
33 7091511 1 NUT, 5/16-18 Hex GR5 or B Was 90196 (continued on next
34 7090187 1 WASHER, 5/16” Split Lock
35 7090316 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 91097
tionItem Qt
Note
page)
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
25
TP 400-5002-4-WB-N
DRIVE SYSTEM SELF-PROPELLED PT.1
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
26
SERIES 17
DRIVE SYSTEM SELF-PROPELLED PT.1
p
y
Part No Descri
36 7032831 1 CONNECTOR, Transfer Rod
37 7091294 1 WASHER, Flat 1/4" used on Self-Propelled Euro only
38 7017696 1 BUSHING
39 7041855 1 DISC, Driven (Cantilever)
40 7090053 1 WASHER, 1/4” Internal Tooth Lock used on Self-Propelled Euro
41 7013847 1 RETAINER, 3/8” Bolt
42 7029025 1 SPRING, Wheel Drive
43 7090799 1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026
-- 7052987 1 ASSEMBLY, Deck Bracket (Incl. items 44, 45 & 46) used on 2002 Models & Earlier
44 7033774 1 BRACKET, Deck
-- 7059462 1 BRACKET, Deck (Incl. item 7) used on 2003 Models & Later
45 7012306 2 BUSHING, lange Plastic
46 7021758 1 SPACER used on Commercial models
47 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5
48 7090391 1 WASHER, 5/16” Internal Tooth Lock
49 7011724 1 WASHER, Spring
50 7091597 1 PIN, 3/32 x 1/2” Cotter Was 90555
51 7091122 2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
52 7090731 1 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
53 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070
54 7012122 1 SPRING, Clutch
55 7012125 1 GUIDE, Thrust Plate (3/8-24 thread)
56 7061275 1 KIT, Drive Disc Assembly comprised of 73528 (disc),
tionItem Qt
Note
91302 (nut), 13893 & 17696
(bushings)
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
27
TP 400-5002-4-WB-N
TRANSMISSION (DIFFERENTIAL)
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
28
SERIES 17
TRANSMISSION (DIFFERENTIAL)
p
y
Part No Descri
-- 7059070 1 ASSEMBLY, Transmission Was 53945 (Includes 1 thru 30)
1 7092062 4 NUT, 5/16-24 Hex Lock, GR C Was 11201
2 7092063 1 WASHER, Cone
3 7019213 1 PULLEY, Poly-Vee Belt
4 7011724 2 WASHER, Spring only 1 shown
5 7053942 1 ASSEMBLY, Right Housing (Includes items 6, 7, 8, 9 & 10)
6 7029034 1 HOUSING, Right Side
7 7014155 3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
8 7012314 2 SEAL, 5/8” Internal Dia.
9 7029035 2 BEARING, Tapered- (Differential Housing)
10 7073963 1 BEARING, Ball, .437 I.D. x 1.125 O.D. x .375 Thk. Was 11767
11 7016544 1 PLUG, Housing
12 7050767 1 GEAR, Input
13 7050830 1 AXLE, Short
14 7012495 1 GEAR, Differential (46 tooth)
15 7031970 2 PLATE, 46T Gear
16 7031965 2 WASHER, Thrust, 3/4” I.D.
17 7090557 4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5 only 1 shown
18 7011774 1 GASKET, Housing
19 7090189 3 WASHER, 5/16” Internal/External Tooth Lock only 1 shown
20 7051903 1 BRACKET, Differential
21 7091825 4 SCREW, 1/4-20 x 1-1/4” Hex Washer Self-Tap only 1 shown
22 7012543 1 SPACER, Axle Gear
23 7050831 1 AXLE, Long
24 7021115 4 GEAR, Pinion (12 tooth)
25 7012500 4 SPACER, Pinion Gear
26 7011110 4 SHAFT, Pinion
27 7090376 4 NUT, #10-32 Hex Nyloc only 1 shown
28 7053939 1 ASSEMBLY, Left Housing (Includes items 8, 9 & 29)
29 7029033 1 HOUSING, Left
30 7024442 3 GASKET, 5/8” O. D.
-- 7061017 “00” Grease (32 oz.)
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
29
TP 400-5002-4-WB-N
THROTTLE CONTROLS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
30
SERIES 17
THROTTLE CONTROLS
p
y
Part No Descri
-- 7029036 1 CONTROL, Throttle (48” long) used on Briggs 4 Cycle
-- 7074829 1 CONTROL, Throttle (46” long) used on Honda 4 Cycle
-- 7075711 1 CONTROL, Throttle (46-3/16” long) used on Honda 4 Cycle
-- 7075712 1 CONTROL, Throttle (49-13/16” long) used on Briggs 4 Cycle
tionItem Qt
Note
Footnotes:
Measure cable on mower before ordering.
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
31
TP 400-5002-4-WB-N
KIT, MUFFLER DEFLECTOR
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
32
SERIES 17
KIT, MUFFLER DEFLECTOR
p
y
Part No Descri
-- 7063302 1 KIT, Muffler Deflector (Includes below 3 items) used on Honda Model
-- 7075292 1 DEFLECTOR, Comp. Muffler Honda # 18430-ZL8-000
-- 7075293 1 CAP, Muffler Honda # 18348-ZL8-000
-- 7075294 4 SCREW, Tapping Honda # 90055-ZE1-000
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
33
TP 400-5002-4-WB-N
ENGINE SPECIFICATIONS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
34
SERIES 17
ENGINE SPECIFICATIONS
p
y
Part No Descri
-- -- 1 ENGINE, 5.5 HP Honda, Recoil Model GCV160A1A; Type
-- -- 1 ENGINE, 6.5 HP B&S, Recoil Model 123K02; Type 0124-E1
-- -- 1 ENGINE, 6.75 HP B&S, Recoil Model 126602; Type 0113-E1
-- -- 1 ENGINE, 6.75 HP B&S, Recoil Model 126602; Type 0116-E1
-- -- 1 ENGINE, 6.75 HP B&S, Electric Start Model 126607; Type 0115-E1
-- -- 1 ENGINE, 6.75 HP B&S, Recoil Model 126602; Type 0117-E1
-- -- 1 ENGINE, 6.75 HP B&S, Recoil Model 126602; Type 0118-E1
-- -- 1 ENGINE, 7 HP B&S, Electric Start Model 128607; Type 0113-E1
-- -- 1 ENGINE, 7 HP B&S, Recoil Model 128602; Type 0149-E1
-- -- 1 ENGINE, 7 HP B&S, Recoil Model 128602; Type 0112-E1
tionItem Qt
Note
635170
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
35
TP 400-5002-4-WB-N
SIDE CHUTE, ADAPTER
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
36
SERIES 17
SIDE CHUTE, ADAPTER
p
y
Part No Descri
1 7051951 ASSY, Bag Adapter & Cover (Incl 8 items below) used on European Models Only
2 7016107 1 ADAPTER, Grass Bag
3 7019287 1 COVER, Bag Adapter
4 7023000 1 HINGE, Chute Cover
5 7091064 5 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
6 7090053 5 WASHER, 1/4” Internal Tooth Lock Was 91023
7 7091576 5 NUT, 1/4-20 Hex Was 91100
8 7032661 1 STOP, Cover
9 7023042 1 MOLDING, Trim
10A 7016050 1 ADAPTER, Grass Bag
10B 7058037 ASSEMBLY, Grass Bag Adapter
11 7024340 1 SPACER, .316 I.D. x .375 O.D. x .310 thick
12 7090951 1 NUT, 5/16-18 Hex Large Flange Center Lock
13 7011791 1 RETAINER, 5/16” Bolt
14 7091508 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001
15 7042965 1 CHUTE, Side
16 7090122 2 WASHER, 3/8" Flat Was 91514
17 7024085 2 WING-NUT, 5/16-18 Nyloc
18 7029149 1 COVER, 21” Deck
19 7090951 2 NUT, 5/16-18 Hex Large Flange Center Lock
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
37
TP 400-5002-4-WB-N
GRASS BAG ACCESSORY
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
38
SERIES 17
GRASS BAG ACCESSORY
p
y
Part No Descri
-- 7061919 1 KIT, Grass Bag Catcher Was 61824 (Includes 2 thru 5)
1 7059322 1 ASSEMBLY, Grass Bag (Includes 2 thru 4) Was 54058
2A 7074425 1 BAG, Door Type (Black w/Gold Letters) (12” Wide)
2B 7075765 1 BAG, Door Type (Black w/Gray Letters) (12” Wide) NOTE: Bag assembly 58571 is
3 7051906 1 ASSEMBLY, Bag Wire (12” Wide)
4 7042489 1 CONNECTOR, Grass Bag (weldment)
5 7016050 1 ADAPTER, Bag for Euro Bag Adapter ass'y see
6 7058037 1 ASSEMBLY, Grass Bag Adapter (Includes items 7 thru 14)
7 7047081 1 ADAPTER, Bag
8 7047082 1 BRACKET, Rope Pulley
9 7091984 1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
10 7012306 1 BUSHING, Flange
11 7024228 1 PULLEY, Plastic
12 7091601 1 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070
13 7072107 4 WASHER, 15/32” Flat
14 7013860 4 RIVET, 3/16 x .344
15 7016814 1 PLUG, Chute Adapter
tionItem Qt
Note
composed of items 2B, 3 & 4.
SIDE CHUTE ADAPTER page.
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
39
TP 400-5002-4-WB-N
DECALS PT. 1
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
40
SERIES 17
DECALS PT. 1
p
y
Part No Descri
1 7024211 1 DECAL, Blade Control
2 7024087 1 DECAL, Speed Select used on Self-Propelled models
3 7013010 1 DECAL, Danger, Cut Finger
4 7029779 1 DECAL, Spark Plug International Symbol
5 7074135 1 DECAL, Noise (European)
6 7073433 1 DECAL, 2001 Year of Manufacture not shown
-- 7074548 1 DECAL, 2002 Year of Manufacture not shown
-- 7075378 1 DECAL, 2003 Year of Manufacture shown
7 7029470 1 DECAL, Patent Numbers
8 7022841 1 DECAL, Warning (Euro)
9 7046357 1 DECAL, Warning
10 7029776 1 DECAL, Euro Community (CE)
11 7029784 1 DECAL, Deck/Chute (European)
12 7072921 1 DECAL, Deck Warning
13 7046720 1 DECAL, Warning Chute/Deflector
14 7036463 1 DECAL, Front Baffle used on “FRP” & “EFRP” Air
tionItem Qt
Note
Models only
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
41
TP 400-5002-4-WB-N
DECALS PT. 2
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
42
SERIES 17
DECALS PT. 2
p
y
Part No Descri
15 7073462 1 DECAL, Caution Symbols
16 7029057 1 DECAL, Medallion
17 7073335 1 DECAL, OPEI
18 7074386 1 DECAL, SNAPPER (Commercial) gold letters/red border/black
-- 7075618 1 DECAL, SNAPPER gray letters/red border/black
19 7041942 1 DECAL, Shift Warning used on Self-Propelled models
20 7016134 1 DECAL, Caution Tag not used in 2003 model year
21 7075619 1 DECAL, Ninja
22 7075750 1 DECAL, Hi-Vac
tionItem Qt
Note
background
background
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
43
TP 400-5002-4-WB-N
SNAPPERIZER ACCESSORY
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
44
SERIES 17
SNAPPERIZER ACCESSORY
p
y
Part No Descri
-- 7060440 1 KIT, Snapperizer (Incl. items 1 & 2 thru 5) used on Hi-Vac Rolled Under-
-- 7063041 1 KIT, Snapperizer (Incl. items 1 & 2A thru 5) used on “FR” Type Decks
1 7051243 1 SCREEN, Fastener Assembly
2 7039759 1 RING, Bottom (21.77” Inside Diameter)
2A 7072002 1 RING, Bottom (22.60” Inside Diameter)
3 7091297 3 NUT, 5/16-24 Hex, GR5 Was 90223, only 1 shown
4 7090187 3 WASHER, 5/16” Split Lock only 1 shown
5 7012587 3 SPRING only 1 shown
tionItem Qt
Note
Lip Decks)
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
45
TP 400-5002-4-WB-N
THATCHERIZER ACCESSORY
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
46
SERIES 17
THATCHERIZER ACCESSORY
p
y
Part No Descri
-- 7061256 1 KIT, Thatcherizer (Incl. items 1 thru 27)
1 7032891 2 LATCH, Frame Attachment
2A 7026572 1 BAR, Mount (Right Hand)
2B 7026573 1 BAR, Mount (Left Hand)
3 7018499 2 ROD, Tine
4 7018700 1 SUPPORT, Wheel
5 7019948 1 TRAY, Tine
6 7018496 6 KIT, Tine Thatching Spring Was 60574
7 7014100 1 BUSHING, Wheel Adjuster
8 7018493 1 AXLE, Wheel
9 7018189 1 WHEEL, 7.00 x 1.50 Gage
10 7091705 10 NUT, 1/4-20 Hex Top Lock Was 90761 (only 9 shown)
11 7091294 4 WASHER, 1/4” Flat Was 90055
12 7022425 2 SPRING, Compression
13 7090825 2 BOLT, 1/4-20 x 1-1/4” Hex, GR5
14 7091576 2 NUT, 1/4-20 Hex, GR5 Was 90063
15 7022424 2 CAP, Vinyl
16 7090015 2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
17 7091303 6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5 Was 90383 (only 1 shown)
18 7091530 2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5 Was 90074
19 7014098 6 WASHER, Reinforcing only 1 shown
20 7090187 6 WASHER, 5/16” Split Lock only 1 shown
21 7091511 6 NUT, 5/16-18 Hex, GR5 Was 90196 (only 1 shown)
22 7014101 2 NUT, 1/2” Push
23 7014342 4 BEARING, Nyliner
24 7014103 1 SCREW, 5/16-18 x 1/4” Set
25 7090250 2 WASHER, 1/2” Flat
26 7014115 1 DECAL, Adjustment
27 7014062 1 DECAL, Thatcherizer
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
47
TP 400-5002-4-WB-N
RECYCLING KITS ACCESSORY
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
48
SERIES 17
RECYCLING KITS ACCESSORY
p
y
Part No Descri
7061200 KIT, Recycling Cover (Includes the 2 items below) for 4HP & above engines
7061201 KIT, Recycling Plug (Incl. items 1 & 2 below) for 4HP & above engines
1 7029149 1 COVER, 21” Deck
2 7016814 1 PLUG, Chute Adapter
3 7026407 1 BLADE, 21” Quad Edge Ninja
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
49
TP 400-5002-4-WB-N
ELECTRIC START COMPONENTS
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
50
SERIES 17
ELECTRIC START COMPONENTS
p
y
Part No Descri
-- 7067012 1 KIT, Battery (Includes 4 items below)
1 7067012 1 BATTERY, 12 Volt, 35 CCA Was 19763
2 7015488 1 HARNESS, Battery
3 7043977 2 SCREW, #10-24 x 1/2” Pan Head Machine
4 7090932 2 NUT, #10-24 Square
-- 7058120 1 ASSEMBLY, Switch/Bracket (Incl items 5 thru 10)
5 7011138 1 KEY (Set of Two)
6 7023506 1 BEZEL (Seal & Face Nut)
7 7071972 1 BRACKET, Ignition Switch
8 7029080 1 COVER, Switch
9 7012685 1 NUT, 5/8-32 Hex Lock
10 7028765 1 SWITCH, Ignition (spring loaded ON/OFF 2 prong)
11 7016132 1 SPACER
12 7090053 2 WASHER, 1/4” Internal Tooth Lock Was 91023
13 7090095 2 NUT, 1/4-28 Hex, GR5 or B Was 91024
14 7074383 1 HARNESS, Wiring
15 7032906 1 BRACKET, Battery
16 7036132 1 COVER, Battery
17 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
18 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR5 Was 90585
19 7012652 1 CLIP, Wiring
20 7061188 1 CHARGER, Battery (120 Volt; 60 Hertz) Was 18834
-- 7018977 1 CHARGER, Battery (230 Volt; 50 Hertz)
21 7090799 1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026
22 7011791 1 RETAINER, 5/16” Bolt
23 7091025 2 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
51
TP 400-5002-4-WB-N
WIRING SCHEMATIC
Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS
TP 400-5002-4-WB-N
52
SERIES 17
WIRING SCHEMATIC
p
y
Part No Descri
-- -- WIRING SCHEMATIC FOR BRIGGS & STRATTON ELECTRIC
STARE ENGINE
tionItem Qt
Note
Footnotes:
Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS
SERIES 17
53
TP 400-5002-4-WB-N
Parts Manual fo
r
21" STEEL DECK WALK BEHIND MOWERS
SERIES 17
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Manual No. 7006136
Revision 4,
1/16/2006
TP 400-5002-4-WB-N
Loading...