Snapper NZMX32734BV, NZMX30614KH User Manual

Parts Manual fo

r

X

H

V

MID MOUNT LARGE FRAME Z-RIDER

ZERO TURNING HYDRO DRIVE NZM

SERIES 4

MODEL

NZMX30614K
NZMX32734B

COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.

Revision IR,

McDonough, GA, 30253 U.S.A.

9/28/2006

Manual No. 7006940

TP 400-5234-IR-NZ-N

s

PAGE GROUP

4
6

8
10
14
16
18
20
22
26
28
30
32
34
36
38
40
44
46
48
52
54
56
58
60
62
64
66
68
70

CASTER WHEEL ASSEMBLY
DRIVE TIRE & WHEEL ASSEMBLY
FRONT CHASSIS ASSEMBLY (Frame)
FRONT CHASSIS ASSEMBLY (Deck Lift)
REAR CHASSIS, PUMPS & PULLEYS
TRACTION DRIVE ASSEMBLY
HOSE & CONNECTOR ASSEMBLY
WHEEL MOTOR ASSEMBLY
TWIN STICK CONTROL ASSEMBLY
PARKING BRAKE ASSEMBLY
HYDRO RESERVOIR ASSEMBLY
FUEL TANK ASSEMBLY
ENGINE GROUP
SEAT ASSEMBLY
BUMPER ASSEMBLY
ROLL BAR PROTECTIVE STRUCTURE
61” CUTTING DECK ASSEMBLY (Sub Assy)
61” CUTTING DECK ASSEMBLY (Final Assy)
IDLER ASSEMBLY (61” Deck)
73” CUTTING DECK ASSEMBLY (Sub Assy)
73” CUTTING DECK ASSEMBLY (Final Assy)
IDLER ASSEMBLY (73” Deck)
DECK SPINDLE ASSEMBLIES
DECALS
CONTROL PANEL ASSEMBLY
ELECTRICAL COMPONENTS
WIRING HARNESS (Briggs Engines)
WIRING HARNESS (Kohler Engines)
WIRING SCHEMATIC (Briggs Engines)
WIRING SCHEMATIC (Kohler Engines)

Table Of Content

SERIES 4

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

3

TP 400-5234-IR-NZ-N

CASTER WHEEL ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

4

SERIES 4

CASTER WHEEL ASSEMBLY

p

y

Part No Descri

1 7092094 2 SCREW, 1/2-13 x 9-1/2” Hex Head Cap, GR 5
2 7075398 2 WELDMENT, Caster Yoke, 7-1/4” Wide
3 7091325 2 NUT, 1/2-13 Hex Nyloc
4 7075461 2 ASSEMBLY, Wheel & Tire
4 7072795 2 ASSY, Wheel & Tire, 13 x 6.50-6 (Incl. items 5A & 8A)
5 7075463 1 TIRE, 13 x 6-6.5 4 Ply

5A 7078277 1 TIRE, 13 x 6-6.50-6 4 Ply Smooth TL (not shown)

6 7028722 2 BALL BEARING, Heim .750 Heim Unibal # RF 12-22-14AP
7 7012700 1 FITTING, 1/4-28 Lube Tapered Head w/Ball Check
8 7075460 1 WELDMENT, Front Wheel Rim

8A 7078285 1 ASSEMBLY, Painted Rim (not shown) Assembly includes Grease

9 7012234 1 AIR VALVE STEM & Cap Goodyear # TR-412 or

10 7075883 2 SPACER
11 7075462 2 SPACER, Bearing, 7.29” Long

tionItem Qt

Note

Fitting & 2 Ball Bearings.

equivalent

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

5

TP 400-5234-IR-NZ-N

DRIVE TIRE & WHEEL ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

6

SERIES 4

DRIVE TIRE & WHEEL ASSEMBLY

p

y

Part No Descri

1 7100524 2 TIRE ASSEMBLY, 26” x 12-2 Multi-Trac
2 7072888 1 TIRE, 26 x 12.00-12 4 Ply Titan Multi-Trac
3 7100297 1 RIM, 12 x 8.50 5/4.5 RAW
4 7012234 1 AIR VALVE STEM & Cap Goodyear # TR-412 or

5 7092073 10 LUG BOLT, 1/2-20 UNF x 7/8”
6 7071819 2 DRUM, Brake (Ausco)
7 7092083 2 CASTLE NUT, 1-14 UNF, GR B included as part of wheel motor
8 7091809 2 COTTER PIN, 1/8 x 1-1/4” included as part of wheel motor

2 KEY, Woodruff included as part of wheel motor

tionItem Qt

Note

equivalent

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

7

TP 400-5234-IR-NZ-N

FRONT CHASSIS ASSEMBLY (Frame)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

8

SERIES 4

FRONT CHASSIS ASSEMBLY (Frame)

p

y

Part No Descri

1 7400018 1 WELDMENT, Front Frame
2 2 GROUP, Front Wheel ref: Caster Wheel Assembly

3 7074723 2 GREASE SEAL
4 7058554 4 BEARING, Tapered Roller 7074706 (tapered roller brg.) &

5 7029137 2 SPACER, Jackstaff
6 7092083 2 CASTLE NUT, 1-1/ UNF, GR B
7 7090841 2 ROLL PIN, 3/16 x 1-1/2”
8 7074537 2 CAP, Dust

9 7400114 1 WELDMENT, Foot Pedestal
10 7090517 2 WASHER, 3/8” Flat SAE
11 7090118 2 WASHER, 3/8” Split Lock
12 7091304 2 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
13 7041818 4 PAD, Floor Board Support
14 7100275 1 FLOOR MAT, Top
15 7300145 1 FOOTPAN
16 7100277 1 FOOTPAN, Mat
17 7300209 1 FOOT STAND, LFNZM
18 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
19 7090768 12 BOLT, 1/2-13 x 1-1/2” Square Neck Carriage, GR 5
20 7091325 12 NUT, 1/2-13 Hex Nyloc
21 7100527 2 HEADLIGHT, w/Connectors Also shown on Electronic

tionItem Qt

Note

Page

7074707 (inner race)

Components page.

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

9

TP 400-5234-IR-NZ-N

FRONT CHASSIS ASSEMBLY (Deck Lift)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

10

SERIES 4

FRONT CHASSIS ASSEMBLY (Deck Lift)

p

y

Part No Descri

1 7015761 1 SHOULDER BOLT, 5/16-18

2 7400161 1 WELDMENT, Transport Lever

3 7090591 3 SCREW, 3/8-16 x 4-1/2 Hex Head Cap, GR 5

4 7090122 8 WASHER, 3/8” Flat SAE

5 7400087 1 WELDMENT, Detent

6 7200075 2 SPACER LIFT

7 7091640 1 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5

8 7200080 1 DETENT SPACER, Upper

9 7090951 1 NUT, 5/16-18 Large Flange Hex Center Lock
10 7091299 5 NUT, 3/8-16 Hex Nyloc
11 7100652 1 DECAL, Detent Channel
12 7100804 1 CLIP, Roll Pin, 1/2”
13 7075086 1 STRAP, Tether
14 7090543 5 SCREW, 1/2-13 x 2” Hex Head Cap, GR 5
15 7091587 10 WASHER, .531 I.D. Flat
16 7101001 4 EYEBOLT, 1/2-13 Open or 7074700
17 7035667 1 SPRING, Extension, Lift Assist
18 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
19 7400050 1 WELDMENT, Bell Crank
20 7091325 2 NUT, 1/2-13 Hex Nyloc
21 7091803 2 KEY, 3/16” Square x 1-1/2”
22 7073326 5 BUSHING, Teflon
23 7044860 1 EYEBOLT, 3/8-16 x 3” spring anchor
24 7091894 4 NUT, 1/2-13 Hex Center Lock, GR 5
25 7075782 4 SWIVEL, Rear Lift (1/2-13 thread)
26 7091316 8 NUT, 1/2-13 Hex GR B
27 7090509 4 WASHER, 3/8” Internal Tooth Lock
28 7400051 1 WELDMENT, Front Lift LH
29 7400049 1 WELDMENT, Rear Lift
30 7092063 1 WASHER, 5/16” Belleville
31 7091315 1 WASHER, 5/16” Split Lock
32 1715834 1 PEDAL, Rubber
33 7400147 1 WELDMENT, Foot Assist
34 7100274 1 ROD, Transfer (1/2-20 thread)
35 7090559 1 NUT, 1/2-20 Hex Jam, GR 5 or B
36 7073012 1 ROD END, 1/2-20 Female
37 7029355 1 BOLT, 1/2-13 x 3-3/4” Hex Head Cap

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

11

TP 400-5234-IR-NZ-N

FRONT CHASSIS ASSEMBLY (Deck Lift)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

12

SERIES 4

FRONT CHASSIS ASSEMBLY (Deck Lift)

p

y

Part No Descri

38 7400017 1 WELDMENT, Front Deck Lift
39 7200059 1 SPACER
40 7300281 1 LINK PLATE
41 7200083 1 SPACER, Bearing
42 7400117 1 WELDMENT, Height Adjuster
43 7200077 1 SPACER, Bearing
44 7900033 1 BOLT, 1/2-13 x 4-1/2” Hex Head, GR 5
45 7091544 10 NUT, 1/2-13 Hex Flange Lock GR 5
46 7090848 4 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

13

TP 400-5234-IR-NZ-N

REAR CHASSIS, PUMPS & PULLEYS

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

14

SERIES 4

REAR CHASSIS, PUMPS & PULLEYS

p

y

Part No Descri

1 7400015 1 WELDMENT, Rear Chassis

2 7100439 1 PUMP, Hydro-Gear BDP-12A W/ RTN left-hand pump

3 7100438 1 PUMP, Hydro-Gear BDP-12A W/ RTN right-hand pump

4 7074738 2 * KIT, Fan Hub (Hydro Gear p/n 70632) for BDP-

5 7074968 2 FAN, 7” Nylon, Counter-Clockwise

6 7091299 4 NUT, 3/8-16 Hex Nyloc

7 7090122 4 WASHER, 3/8” Flat SAE

8 7027199 2 KEY, M5 x M20

9 7013847 4 BOLT RETAINER, 3/8”
10 7027181 4 BOLT, 3/8-16 x 1-1/4” Short Neck Carriage GR 5
11 7041330 2 PULLEY, 4.25 O.D. x 1.375 OA x “H” Tapered Bore double pump
12 7071831 2 PULLEY, “D” Bushing x 15mm Bore
13 7090548 4 SCREW, 1/4-20 x 1” Hex Head Cap GR 5
14 7091627 2 WASHER, 1/4 x 1 x 1/8” Flat
15 7027223 2 WASHER, 1/4” Split Lock
16 7091835 2 SCREW, M6 1.0 x 12mm Hex Head Cap
17 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
18 7090071 4 SCREW, 1/4-20 x 1/2” Hex Head Cap, GR 5
19 7090052 4 WASHER, 1/4” Split Lock
20 7075919 2 BRACKET, Filter
21 5023096 2 FILTER HEAD
22 1719168 2 FILTER

tionItem Qt

Note

10A Pump w/Thru Shaft

Footnotes:

* Note: Includes Fan Mount Hub, Belleville Washer and Hex Nyloc Nut.

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

15

TP 400-5234-IR-NZ-N

TRACTION DRIVE ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

16

SERIES 4

TRACTION DRIVE ASSEMBLY

p

y

Part No Descri

1 7090130 1 NUT, 3/8-16 Hex, GR 5 or B

2 7090118 1 WASHER, 3/8” Split Lock

3 7090122 5 WASHER, 3/8” Flat SAE

4 7091299 2 NUT, 3/8-16 Hex Nyloc

5 7041262 2 PULLEY, 4” O.D. x .391 I.D. x 1.25 Backside Idler

6 7200078 1 SPACER, Pulley

7 7300356 1 MOUNT, Idler Spring

8 7091557 2 SCREW, 3/8-16 x 2-3/4” Hex Head Cap, GR 5

9 7091302 2 NUT, 3/8-16 Hex, GR 5 or B
10 7074777 1 SPACER, Lift Adjust (1.08” Long)
11 7044860 1 EYEBOLT, 3/8-16 x 3”
12 7073992 1 SPRING, Extension
13 7027221 1 BOLT, 3/8-16 x 3-1/2” Hex Head, GR 5
14 7090517 1 WASHER, 3/8” Flat SAE
15 1723806 1 BOSS, Idler Arm Pivot
16 1723805 2 SLEEVE BUSHING, 3/4” I.D.
17 7400086 1 WELDMENT, Drive Idler
18 7091587 1 WASHER, .531 I.D. Flat
19 7091619 1 NUT, 3/8-16 Hex Flange Lock
20 7100724 1 SET, Matched Traction Drive Belt (Kit contains two belts (p/n

21 7100522 2 BELT, HA Sect., 54.48” effective length 4L Traction Drive
22 7017853 1 TRAY, Battery (Polypropylene)

tionItem Qt

Note

7100522)

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

17

TP 400-5234-IR-NZ-N

HOSE & CONNECTOR ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

18

SERIES 4

HOSE & CONNECTOR ASSEMBLY

p

y

Part No Descri

1 7075055 4 CONNECTOR, 45-Degree Hydraulic (Parker # V5OLO-S)

2 7075056 6 CONNECTOR, 90-Degree Hydraulic (Parker # 8-6 C5OLO-S)

3 7075057 2 CONNECTOR, Straight Hydraulic (Parker # 8-6 F5OLO-S)

4 7075058 4 CONNECTOR, Straight Hydraulic (Parker # 8-10 F5OLO-S)

5 7075051 2 HOSE, 17-1/2” Hydraulic (Parker # F436BKJCJ5080808-17.5)

6 7075052 2 HOSE, 18-1/2” (Parker R836BKJCJ9090808-18.5)

7 7075053 2 HOSE, 12-1/4” (Parker # R836BKJ9NR080008-12.5)

8 7075054 2 HOSE, 6-1/2” (Parker # R836BKJ9NR080008-6.5)

9 7075470 2 HOSE, 15-1/2” Hydraulic (Parker # F436JCJ9080808-15.50)

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

19

TP 400-5234-IR-NZ-N

WHEEL MOTOR ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

20

SERIES 4

WHEEL MOTOR ASSEMBLY

p

y

Part No Descri

1 7400074 1 WELDMENT, Rear Support

2 7090768 4 BOLT, 1/2-13 x 1-1/2” Square Neck Carriage, GR 5

3 7075443 2 BRACKET, Wheel Motor Support

4 7091325 6 NUT, 1/2-13 Hex Nyloc

5 7029355 4 BOLT, 1/2-13 x 3-3/4” Hex Head Cap

6 7092087 4 BOLT, 1/2-13 x 6” Hex Head Cap GR 5

7 7100299 1 WHEEL MOTOR, LH HGM 18E-3052

8 7100300 1 WHEEL MOTOR, RH HGM 18E-3056

9 7091322 8 WASHER, 1/2” Split Lock
10 7091316 8 NUT, 1/2-13 Hex GR B
11 7091809 2 COTTER PIN, 1/8 x 1-1/4” included as part of wheel motor
12 7071819 2 DRUM, Brake (Ausco) shown also in DRIVE TIRE &

13 7092083 2 CASTLE NUT, 1-14 UNF, GR B included as part of wheel motor

tionItem Qt

Note

WHEEL ASSEMBLY

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

21

TP 400-5234-IR-NZ-N

TWIN STICK CONTROL ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

22

SERIES 4

TWIN STICK CONTROL ASSEMBLY

p

y

Part No Descri

1 7300077 1 LIMITER BRKT, LH

2 7300076 1 LIMITER BRKT, Twin Stick, Right Side, LFNZM

3 7074964 2 BRACKET, Speed Control

4 7090361 24 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap

5 7100556 2 HANDLEBAR, Twin Stick, LFNZM

6 7100051 2 FOAM GRIP, Handle

7 7300075 1 BUSHING MOUNT PLATE, LH

8 7300074 1 BUSHING MOUNT PLATE, Right Side, LFNZM

9 7072934 4 BUSHING, Teflon Impregnated
10 7091628 4 WASHER, .64 I.D. x .99 O.D. x .05 Flat
11 7400053 2 WELDMENT, Shaft Twin
12 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
13 7090188 16 WASHER, 5/16” Flat
14 7027139 4 ROD END (5/16-24 thread)
15 7091297 4 NUT, 5/16-24 Hex, GR 5 or B
16 7100294 2 LINKAGE, Pump Control (5/16-24 threads)
17 7091298 8 NUT, 5/16-18 Hex Nyloc
18 7091603 10 NUT, 1/4-20 Hex Nyloc
19 7091294 8 WASHER, 1/4” Flat
20 7073061 2 MOUNTING PLATE, Left Hand Bearing
21 7090548 4 SCREW, 1/4-20 x 1” Hex Head Cap GR 5 or 7027230
22 7010739 2 RING, 5/8” External Retaining
23 7090669 4 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5
24 7100484 2 MOUNTING ARM, Twin Stick
25 7090588 2 SCREW 3/8-16 x 2” Hex Head Cap, GR 5 or 7091305
26 7075029 2 SPACER, .498 O.D. x 1.010” long
27 7091299 2 NUT, 3/8-16 Hex Nyloc
28 7071825 2 BRACKET, Handle Adjustment
29 7091003 4 SCREW, 1/4-20 x 1-3/4” Hex Head Cap, GR 5 or 7091813
30 7091803 2 KEY, 3/16” Square x 1-1/2”
31 7079577 2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap GR 5
32 7090848 2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point
33 7400032 1 MOUNTING HUB WELDMENT, T-Stick LH
34 7400031 1 MOUNTING HUB WELDMENT, T-Stick RH
35 7090372 2 NUT, 1/4-20 Hex Center Lock
36 5022978 2 DAMPENER, Hydraulic
37 7900007 2 SCREW, Shoulder Socket Head (1/4-20 thread)

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

23

TP 400-5234-IR-NZ-N

TWIN STICK CONTROL ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

24

SERIES 4

TWIN STICK CONTROL ASSEMBLY

p

y

Part No Descri

38 7027174 2 SCREW, 5/16-18 x 2” Hex Head Cap, GR 5
39 7090585 4 NUT, 5/16-18 Hex Flange Lock
40 7300144 1 CENTER BRACKET, Joystick

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

25

TP 400-5234-IR-NZ-N

PARKING BRAKE ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

26

SERIES 4

PARKING BRAKE ASSEMBLY

p

y

Part No Descri

1 7010739 3 RING, 5/8” External Retaining

2 7092091 1 GROOVE PIN, 1/4 x 1-1/4” long

3 7024159 8 PIN, 3/8” Self Locking Cotter or 7091593

4 7011231 2 SWIVEL, 3/8” Thru Hole, Special

5 7046451 2 SWIVEL, 3/8-24 Adjustment

6 7046782 2 SPRING, Rectangular Wire Die, Blue

7 7400016 1 WELDMENT, Brake Rod

8 7059085 1 WELDMENT, Park Brake Handle

9 7059086 2 WELDMENT, Park Brake Pivot Bracket
10 7059087 2 WELDMENT, Brake Linkage Bellcrank
11 7071820 2 ASSEMBLY, Brake Ausco p/n CC 83022
12 7041140 2 PLATE, Brake Mounting
13 7072934 6 BUSHING, Teflon Impregnated
14 7073989 2 FRONT LINKAGE, Park Brake (3/8-24 thread)
15 7072094 2 ROD, Brake Rear (3/8-16 thread)
16 7074196 1 GRIP, Parking Brake
17 7090122 4 WASHER, 3/8” SAE Flat
18 7090482 2 NUT, 3/8-24, Hex Jam, GR 5 or B
24 7091518 2 NUT, 3/8-24 Hex Nyloc
19 7091298 6 NUT, 5/16-18 Hex Nyloc
20 7091508 6 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
21 7091628 5 WASHER, .64 I.D. x .99 O.D. x .05 Flat
22 7041148 4 SHOULDER BOLT, 3/8-16 Hex Socket Head
23 7091585 4 NUT, 3/8-16 Hex Center Lock

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

27

TP 400-5234-IR-NZ-N

HYDRO RESERVOIR ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

28

SERIES 4

HYDRO RESERVOIR ASSEMBLY

p

y

Part No Descri

1 7059088 2 ASSY, Hydraulic Tank (Includes 4 items shown below)

2 7074002 1 TANK, Hydraulic, NZM per 7059088, Tank Assembly

3 7075289 1 CAP, Vented (Kelch # H4550D) per 7059088, Tank Assembly

4 7075687 2 GROMMET (Dapco # 12078) per 7059088, Tank Assembly

5 7073238 2 ELBOW FITTING (Dapco # 12183) per 7059088, Tank Assembly

6 7073999 1 BRACKET, R.H. Hydro Tank Mount

7 7074001 1 BRACKET, L.H. Hydro Tank Mount

8 7090548 8 SCREW, 1/4-20 x 1” Hex Head Cap GR 5

9 7091294 16 WASHER, 1/4” Flat
10 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
11 7091603 8 NUT, 1/4-20 Hex Nyloc
12 7012080 5 CABLE TIE, 7” Long (not shown)

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

29

TP 400-5234-IR-NZ-N

FUEL TANK ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

30

SERIES 4

FUEL TANK ASSEMBLY

p

y

Part No Descri

1 7024669 1 ASSEMBLY, LH Fuel Tank includes: tank (7042924) plus

2 7100217 1 ASSEMBLY, RH Fuel Tank includes: tank (7042925) plus

3 7046326 1 ASSEMBLY, Fuel Pickup includes items 4 & 5

4 7074835 1 ELBOW, 90 Degree

5 7046804 1 TUBE, Pickup

6 7012337 1 GROMMET, Tube Dapco p/n 10672

7 7078165 1 GAGE, Fuel

8 7011247 1 GROMMET, Gage

9 7100211 1 LID, Fuel Tank
10 7075135 1 CAP, 3-1/2” Fuel Kelch p/n 201906
11 7092089 6 SCREW, 7/16-14 x 2” Hex Head Cap, GR 5
12 7090250 8 WASHER, 1/2” Flat SAE
13 7091294 2 WASHER, 1/4” Flat
14 7027223 2 WASHER, 1/4” Split Lock
15 7090825 2 SCREW, 1/4-20 x 1-1/4” Hex Head Cap, GR 5
16 7092088 2 SCREW, 5/16-18 x 2-1/2” Hex Head Cap, GR 5
17 7090188 2 WASHER, 5/16” Flat
18 7091298 2 NUT, 5/16-18 Hex Nyloc
19 7091640 2 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
20 7091299 2 NUT, 3/8-16 Hex Nyloc
21 7091917 6 NUT, 7/16-14 Hex Nyloc
22 7044681 1 FUEL VALVE, 3-Way
23 7300382 1 BRACKET, Tank Selector
24 7074688 3 HOSE, 1/4” I.D. x 3'-7.5” Long Fuel
25 7012222 6 CLAMP, Fuel Hose
26 7012080 5 CABLE TIE, 7” Long (not shown)

tionItem Qt

Note

items 3, 6, 7, 8 & 10

items 3, 6, 7, 9 & 10

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

31

TP 400-5234-IR-NZ-N

ENGINE GROUP

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

32

SERIES 4

ENGINE GROUP

p

y

Part No Descri

1 1 * ENGINE, 32 HP Briggs Vanguard Vertical Model # 543777 Type 0120 Trim

1 1 * ENGINE, Kohler 30 HP (not shown) Model # CV750S

2 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5

3 7011791 4 BOLT RETAINER, 5/16” Bolt

4 7090188 4 WASHER, 5/16” Flat

5 7091706 5 NUT, 5/16-18 Hex Top Lock GR B

6 7100803 1 ASSEMBLY, Oil Drain Hose used on Briggs Model only

7 7091640 2 BOLT, 3/8-16 x 1” Square Neck Carriage GR 5

8 7300399 1 GUARD, Muffler NZMX used on NZMX32734BV

9 7091299 2 NUT, 3/8-16 Hex Nyloc
10 7200094 1 KEY, 1/4” Square x .360” used on Briggs Model only
10 7016755 1 KEY, 1/4” Square x 3/4” used on Kohler model
11 7100292 1 PULLEY, 4.26 O.D. x 1.375 OAL x 1.125 Bore
12 7200058 1 SPACER, Clutch
13 7017033 1 KEY, 1/4” Square x 2-1/4” Long
14 7100436 1 ELECTRIC CLUTCH, GT3.5 Qgura Model # GT3.5-FE05
15 7075082 1 WASHER, .468 x 1.85 x .25 Flat for Ogura Clutch
16 7091301 1 WASHER, 7/16” Split Lock

17A 7100712 1 SCREW, 7/16-20 x 2” Hex Head Cap, GR 5 (w/Nyloc Patch); used on Briggs

17B 7027266 1 SCREW, 7/16-20 x 3” Hex Head Cap, GR 5 (w/Nyloc Patch); used on Kohler

18 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
19 7073012 1 ROD END, 1/2-20 Female
20 7090517 3 WASHER, 3/8” Flat SAE
21 7090122 1 WASHER, 3/8” Flat SAE
22 7090155 1 NUT, 3/8-24 Hex, GR B
23 7090559 1 NUT, 1/2-20 Hex Jam, GR 5 or B
24 7100586 1 CLUTCH ROD (1/2-20 thread)
25 7091304 1 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
26 7300217 1 BRACKET, Clutch
27 7091585 2 NUT, 3/8-16 Hex Center Lock
28 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
29 7075734 1 OUTLET, Muffler used on NZMX30614KH only
30 7091581 4 SCREW, #8-18 x 1/2” Hex Washer Self-Tap

tionItem Qt

Note

E1

model

model

Footnotes:

* NOTE: Purchase engine components directly from engine manufacturer dealer.

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

33

TP 400-5234-IR-NZ-N

SEAT ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

34

SERIES 4

SEAT ASSEMBLY

p

y

Part No Descri

1 7029338 1 SEAT ASSY, Mid Back Trim Line Static Suspension Seats Inc. p/n 179035VD310

2 7012080 3 CABLE TIE, 7” Long

3 7300207 1 FAN GUARD

4 7091298 8 NUT, 5/16-18 Hex Nyloc

5 7090799 2 BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5

6 7100817 1 DECAL, Caution Fan

7 7091640 2 BOLT, 3/8-16 x 1” Square Neck Carriage GR 5

8 7090361 6 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap

9 7091067 2 NUT, 5/16-18 Hex Center Lock
10 7011791 6 BOLT RETAINER, 5/16” Bolt
11 7300126 1 CROSSMEMBER, Seat Support
12 7075433 1 DECAL, Oil Level Reservoir
13 7074218 2 SPRING, Compression- Seat Support
14 7090122 2 WASHER, 3/8” SAE Flat
15 7091299 2 NUT, 3/8-16 Hex Nyloc
16 7300451 1 SEAT LATCH, Left
17 7300441 1 BRACKET, Seat Latch, NZMX
18 7026292 1 SPRING, Extension
19 7091595 4 WASHER .47 x .92 x .065 Flat
20 7015761 4 SHOULDER BOLT, 5/16-18
21 7300452 1 LINK, Seat Latch
22 7400151 1 WELDMENT, Seat Pan
23 7027174 2 SCREW, 5/16-18 x 2” Hex Head Cap, GR 5
24 7090188 18 WASHER, 5/16” Flat
25 7035638 1 CLIP, Open J 3/8” Cushioned
26 7033362 1 HOLDER, Seat Switch
27 7023354 1 SWITCH, Seat, NC
28 7022793 2 BUSHING, Seat (Black Nylon)
29 7026249 2 SPACER/WASHER
30 7022794 2 SPACER
31 7071767 2 SPRING, Compression
32 7091289 2 SCREW, #10-32 x 5/8” Hex Washer Self-Tap, GR 5
33 7900040 2 SCREW, 5/16-18 x 5-1/2” Hex Head Cap, GR 5
34 7300442 1 BRACKET, Seat Stop, NZMX

tionItem Qt

Note

Silver/Black

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

35

TP 400-5234-IR-NZ-N

BUMPER ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

36

SERIES 4

BUMPER ASSEMBLY

p

y

Part No Descri

1 7400089 1 WELDMENT, Bumper LH

2 7400142 1 WELDMENT, Bumper

3 7100843 1 DECAL, Warning, Rollbar (Spanish)

4 7300437 1 GUARD, Hot Plate used on Kohler Model only

5 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap

6 7091640 14 BOLT, 3/8-16 x 1” Square Neck Carriage GR 5

7 7091299 14 NUT, 3/8-16 Hex Nyloc

8 7090122 8 WASHER, 3/8” Flat SAE

9 7013847 4 BOLT RETAINER, 3/8”
10 7300438 2 BRACKET, Bumper Support, Middle
11 7091298 2 NUT, 5/16-18 Hex Nyloc
12 7300219 1 BRACKET, Rear Bumper
13 7091303 2 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
14 5100683 1 DECAL, Warning, Rollbar

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

37

TP 400-5234-IR-NZ-N

ROLL BAR PROTECTIVE STRUCTURE

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

38

SERIES 4

ROLL BAR PROTECTIVE STRUCTURE

p

y

Part No Descri

1 7100675 1 WELDMENT, Loop

2 7100099 2 STAR KNOB (5/16-18 thread)

3 7100095 2 PIN, Hinge (ROPS)

4 7029355 2 BOLT, 1/2-13 x 3-3/4” Hex Head Cap

5 7300446 2 BRACKET, ROPS Stop, NZMX

6 7090975 7 NUT, 1/2-13 Hex Center Lock, GR 5 or 7091894

7 7100674 2 WELDMENT, Post

8 7091299 5 NUT, 3/8-16 Hex Nyloc

9 7900033 4 BOLT, 1/2-13 x 4-1/2” Hex Head, GR 5
10 7091304 7 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
11 7300314 2 PLATE, Seat Belt
12 7100228 1 SEAT BELT, w/Metal Strap
13 7091585 1 NUT, 3/8-16 Hex Center Lock
14 7100227 1 RETRACTER, Seat Belt
15 7090646 1 SCREW, 1/2-13 x 1” Hex Head Cap, GR 5
16 7100284 1 DECAL, ROPS Overhang
17 7100173 1 DECAL, Warning ROPS (Spanish)
18 7100172 1 DECAL, Warning ROPS
19 7100171 1 DECAL, Caution ROPS (Spanish)
20 7100170 1 DECAL, Caution ROPS

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

39

TP 400-5234-IR-NZ-N

61” CUTTING DECK ASSEMBLY (Sub Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

40

SERIES 4

61” CUTTING DECK ASSEMBLY (Sub Assy)

p

y

Part No Descri

1 7400157 1 WELDMENT, 61” Deck, NZMX

2 7091640 12 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5

3 7091299 15 NUT, 3/8-16 Hex Nyloc

4 7091304 12 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

5 7091553 2 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5

6 7091331 4 WASHER, .406 x 1.50 x .120 Flat

7 7044752 2 SPACER, 3/4 O.D. x 13/32 I. D. x 3/4” long

8 7091585 4 NUT, 3/8-16 Hex Center Lock

9 7090517 4 WASHER, 3/8” Flat SAE
10 7029355 6 BOLT, 1/2-13 x 3-3/4” Hex Head Cap
11 7091325 12 NUT, 1/2-13 Hex Nyloc
12 7027327 1 WELDMENT, Pivot Pin
13 7300420 1 BRACKET, RH Front
14 7300421 1 BRACKET, LH Front
15 7300212 1 FRONT ROLLER BRKT, RH
16 7300214 1 FRONT ROLLER BRKT, LH
17 7036460 1 TUBE, Roller
18 7036461 1 ROD, Roller (1/2-13 Threaded)
19 7073142 3 ROLLER, Low Density Polyethylene or 7079226
20 7027344 2 WASHER, 5/8” Flat SAE
21 7079868 2 ROLLER 3-3/4 Dia. x 4-13/16” long Polyethylene
22 7079882 2 TUBE, Axle
23 7091617 2 SCREW, 3/8-16 x 6” Hex Head Cap, GR 5
24 7400153 2 WELDMENT, Caster, Gauge Wheel
25 7023747 4 BUSHING, 1” Machine
26 7074720 4 BUSHING, Idler (Powdered Metal)
27 7400154 2 WELDMENT, Gauge Wheel Support
28 7014669 2 LUBE FITTING, 3/16”
29 7012709 2 RING, 1” External Retaining
30 7044839 2 CAP, Caster Shaft
31 7091541 2 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
32 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
33 7091619 2 NUT, 3/8-16 Hex Flange Lock
34 7300418 1 BRACKET, RH Rear
35 7300419 1 BRACKET, LH Rear
36 7091822 2 BOLT, 1/2-13 x 5” Hex Head
37 7036457 2 BRACKET, Gauge Wheel

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

41

TP 400-5234-IR-NZ-N

61” CUTTING DECK ASSEMBLY (Sub Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

42

SERIES 4

61” CUTTING DECK ASSEMBLY (Sub Assy)

p

y

Part No Descri

38 7029264 2 GAUGE WHEEL, Polyethylene
39 7036456 2 SPACER, Gauge Wheel
40 7300064 2 BRACKET, Stabilizer
41 7044823 2 WELDMENT, Pusher Bar
42 7029258 8 BUSHING- Suspension
43 7029263 4 SLEEVE, Suspension

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

43

TP 400-5234-IR-NZ-N

61” CUTTING DECK ASSEMBLY (Final Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

44

SERIES 4

61” CUTTING DECK ASSEMBLY (Final Assy)

p

y

Part No Descri

1 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap

2 7075384 2 SPINDLE COVER, 61” Deck

3 1 ASSEMBLY, Idler (ref. Idler Assy page)

4 7091304 3 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

5 7100912 1 * BELT, HB Section (97.0” nominal effective length)

6 7029268 1 * V-BELT, Secondary- 61” (HB Section) (127.0” nominal effective length)

7 7029278 1 SPRING, Idler (1.17” O.D. x 7.5” long)

8 7072915 1 SPRING, Idler Primary (1.25” O.D. x 10” long)

9 7027950 1 SPRING, Chute
10 7091313 1 COTTER PIN, 3/32 x 1”
11 7029277 1 PIN, Chute Hinge
12 7091299 7 NUT, 3/8-16 Hex Nyloc
13 2 ASSY, Outer Spindle (ref. Deck Spindle Assy page)
14 1 ASSY, Center Spindle (ref. Deck Spindle Assy page)
15 7500232 1 ASSEMBLY, 61” Discharge Chute incl. items 12, 16, 17, 18 & 19
16 7300034 1 DEFLECTOR BOTTOM (61” Deck)
17 7091790 4 BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5
18 7100622 1 CHUTE, Rubber (61” Deck)
19 7400007 1 WELDMENT, Discharge Chute 61”

tionItem Qt

Note

Footnotes:

* NOTE: Snapper part number stamped on belt

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

45

TP 400-5234-IR-NZ-N

IDLER ASSEMBLY (61” Deck)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

46

SERIES 4

IDLER ASSEMBLY (61” Deck)

p

y

Part No Descri

1 7058147 1 WELDMENT, Idler Plate

2 1 ASSEMBLY, Primary Idler Includes items 6 (2), 7, 8 (3), 9,

3 1 ASSEMBLY, Secondary Idler Includes items 6 (2), 7, 8, 9, 15,

4 7023747 2 BUSHING, 1” Machine

5 7012709 2 RING, 1” External Retaining

6 7074720 2 BUSHING, Idler (Powdered Metal)

7 7014669 2 LUBE FITTING, 3/16”

8 7090517 4 WASHER, 3/8” Flat SAE

9 7091585 2 NUT, 3/8-16 Hex Center Lock
10 7027220 1 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
11 7058877 1 WELDMENT, Primary Idler Arm
12 7035657 1 BUSHING- Idler
13 7035656 1 RETAINER, Idler Belt
14 7034422 1 PULLEY, Flat Idler, 5.0 x .375 (Belt Clutch)
15 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
16 7058329 1 WELDMENT, Secondary Idler Arm
17 7029273 1 PULLEY, Idler

tionItem Qt

Note

10, 11, 12, 13 & 14

16 & 17

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

47

TP 400-5234-IR-NZ-N

73” CUTTING DECK ASSEMBLY (Sub Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

48

SERIES 4

73” CUTTING DECK ASSEMBLY (Sub Assy)

p

y

Part No Descri

1 7011791 6 BOLT RETAINER, 5/16” Bolt

2 7090799 6 BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5

3 7091299 22 NUT, 3/8-16 Hex Nyloc

4 7091304 13 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

5 7091640 22 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5

6 7074720 4 BUSHING, Idler (Powdered Metal)

7 7090517 4 WASHER, 3/8” Flat SAE

8 7091585 4 NUT, 3/8-16 Hex Center Lock

9 7029258 8 BUSHING- Suspension
10 7029355 4 BOLT, 1/2-13 x 3-3/4” Hex Head Cap
11 7029263 4 SLEEVE, Suspension
12 7044823 2 WELDMENT, Pusher Bar
13 7091922 4 NUT, 1/2-13 Hex Light Nyloc
14 7300019 1 73” DECK STIFFENER
15 7091305 2 SCREW 3/8-16 x 2” Hex Head Cap, GR 5
16 7091331 4 WASHER, .406 x 1.50 x .120 Flat
17 7012117 2 BUSHING, 3/8” Plastic
18 7091619 2 NUT, 3/8-16 Hex Flange Lock
19 7091541 2 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
20 7044839 2 CAP, Caster Shaft
21 7012709 2 RING, 1” External Retaining
22 7023747 4 BUSHING, 1” Machine
23 7400154 2 WELDMENT, Gauge Wheel Support
24 7014669 2 LUBE FITTING, 3/16”
25 7091617 2 SCREW, 3/8-16 x 6” Hex Head Cap, GR 5
26 7400153 2 WELDMENT, Caster, Gauge Wheel
27 7079882 2 TUBE, Axle
28 7079868 2 ROLLER 3-3/4 Dia. x 4-13/16” long Polyethylene
29 7044752 2 SPACER, 3/4 O.D. x 13/32 I. D. x 3/4” long
30 7400004 1 WELDMENT, 73” DECK
31 7091553 3 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
32 7300064 2 BRACKET, Stabilizer
33 7300176 1 BRACKET, Deck Lift, RH Rear
34 7300177 1 BRACKET, Deck Lift, LH Rear
35 7091325 5 NUT, 1/2-13 Hex Nyloc
36 7036456 2 SPACER, Gauge Wheel
37 7029264 2 GAUGE WHEEL, Polyethylene

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

49

TP 400-5234-IR-NZ-N

73” CUTTING DECK ASSEMBLY (Sub Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

50

SERIES 4

73” CUTTING DECK ASSEMBLY (Sub Assy)

p

y

Part No Descri

38 7036457 2 BRACKET, Gauge Wheel
39 7091822 2 BOLT, 1/2-13 x 5” Hex Head
40 7300175 2 DECK LIFT BRACKET, Front
41 7300285 2 ANGLE, Deck Stiffener, 73 Deck
42 7027327 1 WELDMENT, Pivot Pin
43 7036461 1 ROD, Roller (1/2-13 Threaded)
44 7300212 1 BRACKET, Front Roller, RH
45 7300214 1 BRACKET, Front Roller, LH
46 7036460 1 TUBE, Roller
47 7073142 3 ROLLER, Low Density Polyethylene or 7079226
48 7027344 2 WASHER, 5/8” Flat SAE

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

51

TP 400-5234-IR-NZ-N

73” CUTTING DECK ASSEMBLY (Final Assy)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

52

SERIES 4

73” CUTTING DECK ASSEMBLY (Final Assy)

p

y

Part No Descri

1 7100516 6 KNOB, Fluted, 5/16-18 x 5/8”

2 7300129 1 GUARD, Pulley, RH

3 1 ASSEMBLY, Idler (see breakdown on Idler Assy page)

4 7091304 3 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

5 7100519 1 * BELT, HB Section, (engine to deck) (106.434” nominal effective

6 7100521 1 * V-BELT, Secondary, HB Section (141.871” nominal effective

7 7035667 1 SPRING, Extension, Lift Assist

8 7072915 1 SPRING, Idler Primary (1.25” O.D. x 10” long)

9 7027950 1 SPRING, Chute
10 7091313 1 COTTER PIN, 3/32 X 1”
11 7029277 1 PIN, Chute Hinge
12 7091299 7 NUT, 3/8-16 Hex Nyloc
13 2 ASSEMBLY, Spindle (ref. Deck Spindle Assy page)
14 1 ASSEMBLY, Center Spindle (ref. Deck Spindle Assy page)
15 7500233 1 ASSEMBLY, 73” Discharge Chute incl. items 12, 16, 17, 18 & 19
16 7300368 1 DEFLECTOR, Bottom, 73” Deck
17 7091790 4 BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5
18 7100669 1 CHUTE, Rubber, 73”
19 7400148 1 WELDMENT, Discharge Chute Top, 73”
20 7300371 1 GUARD, Pulley, LH

tionItem Qt

Note

length)

length)

Footnotes:

* NOTE: Snapper part number stamped on belt

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

53

TP 400-5234-IR-NZ-N

IDLER ASSEMBLY (73” Deck)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

54

SERIES 4

IDLER ASSEMBLY (73” Deck)

p

y

Part No Descri

1 7400113 1 WELDMENT, Idler Pivot Plate

2 1 ASSEMBLY, Primary Idler

3 1 ASSEMBLY, Secondary Idler

4 7023747 2 BUSHING, 1” Machine

5 7012709 2 RING, 1” External Retaining

6 7023556 4 BUSHING, Caster

7 7014669 2 LUBE FITTING, 3/16”

8 7400111 1 WELDMENT, Deck Idler Arm

9 7400112 1 WELDMENT, Secondary Idler Bracket
10 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
11 7029273 1 PULLEY, Idler
12 7090517 2 WASHER, 3/8” Flat SAE
13 7091585 2 NUT, 3/8-16 Hex Center Lock
14 7091305 3 SCREW 3/8-16 x 2” Hex Head Cap, GR 5
15 7091331 2 WASHER, .406 x 1.50 x .120 Flat
16 7012117 2 BUSHING, 3/8” Plastic
17 7091619 2 NUT, 3/8-16 Hex Flange Lock
18 7091299 2 NUT, 3/8-16 Hex Nyloc
19 7035789 1 PULLEY, Flat Idler, 5.5 O.D.
20 7300444 1 RETAINER- Belt- Idler

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

55

TP 400-5234-IR-NZ-N

DECK SPINDLE ASSEMBLIES

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

56

SERIES 4

DECK SPINDLE ASSEMBLIES

p

y

Part No Descri

1 7063237 3 NUT, 5/8-11 Hex Flange Lock, GR 5

2 7029270 2 WASHER, Spindle

3 7029250 1 PULLEY, Driven (61” Deck only)

3 7100518 1 PULLEY- Driven (73” Deck only)

4 7029245 3 PULLEY, 5.75” Diameter

5 7074401 6 WASHER, Spindle

6 7091299 18 NUT, 3/8-16 Hex Nyloc

7 7091154 6 RETAINING RING, Internal

8 7029422 6 BALL BEARING (double sealed, double shield)

9 7045092 3 WELDMENT, 48” Spindle
10 7029384 3 VENT, Spindle (Alemite # 321839)
11 7076998 3 LUBE FITTING, 1/4-28 Straight or 7014669
12 7091640 18 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5 used on 61” Decks
12 7091790 18 BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5 used on 73” decks
13 7200025 3 SPINDLE SHAFT (5/8-11 threads)
14 7063238 3 SEAL, Nylos
15 7075770 3 BLADE, 21” (61” Deck only)
15 7100721 3 BLADE, 25” (71” Deck only)
16 7016440 3 WASHER, Beveled
17 7091976 3 SCREW, 5/8-11 x 1-3/4” Hex Head Cap, GR 5

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

57

TP 400-5234-IR-NZ-N

DECALS

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

58

SERIES 4

DECALS

p

y

Part No Descri

1 7074862 2 DECAL, Snapper Pro

2 7100652 1 DECAL, Detent Channel

3 7100696 1 DECAL, Control Panel

4 7100708 1 DECAL, 3500 Z, 30 HP

5 7100707 1 DECAL, 3500 Z, 32 HP

6 7075296 1 DECAL, Caution, Spring Tension

7 7100817 1 DECAL, Caution Fan

8 7100170 1 DECAL, Caution ROPS

9 7100171 1 DECAL, Caution ROPS (Spanish)
10 7075433 1 DECAL, Oil Reservoir Overfill Warning
11 7075039 1 DECAL, Motion Control Levers
12 7100284 1 DECAL, ROPS Overhang
13 7035846 1 DECAL, Fuse
14 7073647 2 DECAL, Danger, Guard/Catcher
15 7100697 1 DECAL, Parking Brake Lever & Lights
16 7100843 2 DECAL, Warning (SP)
17 5100683 2 DECAL, Warning, Rollbar
18 7100172 1 DECAL, Warning ROPS
19 7100173 1 DECAL, Warning ROPS (Spanish)
20 7075567 1 DECAL, 61” Deck, (silver)
21 7046371 1 DECAL, 73” Deck
22 7027733 1 DECAL, Ear Protection
23 7045108 1 DECAL, Tank Selector, MMZ

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

59

TP 400-5234-IR-NZ-N

CONTROL PANEL ASSEMBLY

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

60

SERIES 4

CONTROL PANEL ASSEMBLY

p

y

Part No Descri

1 7300143 1 CONTROL PANEL, Detached

2 7035659 1 * SWITCH, Lights

3 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap

4 7072684 1 * SWITCH, Ignition

5 7091240 4 SCREW, #10-32 x 5/8” Hex Washer Self-Tap

6 7075132 1 * SWITCH, PTO, Yellow

7 7074796 1 * HOUR METER w/Flash Alerts

8 7075086 1 STRAP, Tether

9 7300225 1 CHOKE PLATE, Kohler
10 7074801 2 CONTROL LEVER, Throttle/Choke
11 7090376 4 NUT, #10-32 Nyloc
12 7100528 2 CABLE, Throttle Control
13 7100697 1 DECAL, Parking Brake Lever & Lights Ref: Decal Page
14 7100696 1 DECAL, Control Panel Ref: Decal Page

tionItem Qt

Note

Footnotes:

* Note: Also shown on Electrical Components page.

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

61

TP 400-5234-IR-NZ-N

ELECTRICAL COMPONENTS

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

62

SERIES 4

ELECTRICAL COMPONENTS

p

y

Part No Descri

1 7075132 1 * SWITCH, PTO, Yellow

2 7012080 8 CABLE TIE, 7” Long

3 7023354 1 S WITCH, Seat, NC also shown on SEAT

4 7072684 1 *SWITCH, Ignition Indak p/n D473A

5 7091240 2 SCREW, #10-32 x 5/8” Hex Washer Self-Tap

6 7090376 2 NUT, #10-32 Nyloc

7 7015861 1 CLIP, Harness

8 7100527 2 HEADLIGHT, w/Connectors

9 7074796 1 * HOUR METER w/Flash Alerts Sendec Corp. Model No. 804-

10 7035659 1 * SWITCH, Lights
11 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap GR 5
12 7075911 1 BATTERY, 11 Plate 375CCA- Wet
13 7091294 2 WASHER, 1/4” Flat
14 7090372 2 NUT, 1/4-20 Hex Center Lock
15 7022886 3 SWITCH, DP NO/NC Snap-In
16 7073406 1 KEY SET, Ignition (not shown) qty. 2 keys per set

tionItem Qt

Note

ASSEMBLY page

204

Footnotes:

* Note: Also shown on Control Panel Assembly Page.

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

63

TP 400-5234-IR-NZ-N

WIRING HARNESS (Briggs Engines)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

64

SERIES 4

WIRING HARNESS (Briggs Engines)

p

y

Part No Descri

1 7074795 1 WIRE HARNESS, Briggs 32 HP

2 7100700 1 WIRE HARNESS, Lights

3 7100768 1 WIRE HARNESS, Engine

4 7100766 1 WIRE HARNESS, Ground not shown

5 7100767 1 WIRE HARNESS, Power not shown

6 7100769 1 WIRE HARNESS, Clutch not shown

7 7075038 1 CABLE, Battery- Positive (6 Gage, 34” long) not shown

8 7035609 1 CABLE, Battery- Ground (6 Gage/14 Gage, 23” long) not shown

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

65

TP 400-5234-IR-NZ-N

WIRING HARNESS (Kohler Engines)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

66

SERIES 4

WIRING HARNESS (Kohler Engines)

p

y

Part No Descri

1 7029337 1 WIRE HARNESS, Kohler/Twin

2 7100700 1 WIRE HARNESS, Lights

3 7100766 1 WIRE HARNESS, Ground not shown

4 7100767 1 WIRE HARNESS, Power not shown

5 7100769 1 WIRE HARNESS, Clutch not shown

6 7075038 1 CABLE, Battery- Positive (6 Gage, 34” long) not shown

7 7035609 1 CABLE, Battery- Ground (6 Gage/14 Gage, 23” long) not shown

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

67

TP 400-5234-IR-NZ-N

WIRING SCHEMATIC (Briggs Engines)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

68

SERIES 4

WIRING SCHEMATIC (Briggs Engines)

p

y

Part No Descri

1 7074795 1 HARNESS, Wiring

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

69

TP 400-5234-IR-NZ-N

WIRING SCHEMATIC (Kohler Engines)

Manual No. 7006940 MID MOUNT LARGE FRAME Z-RIDER
TP 400-5234-IR-NZ-N

70

SERIES 4

WIRING SCHEMATIC (Kohler Engines)

p

y

Part No Descri

1 7029337 1 HARNESS, Wiring, Kohler/Twin

tionItem Qt

Note

Footnotes:

Manual No. 7006940MID MOUNT LARGE FRAME Z-RIDER

SERIES 4

71

TP 400-5234-IR-NZ-N

Parts Manual fo

r

MID MOUNT LARGE FRAME Z-RIDER

ZERO TURNING HYDRO DRIVE NZMX

SERIES 4

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS

COPYRIGHT ©2006

SNAPPER PRODUCTS, INC.

ALL RIGHTS RESERVED.

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS

WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE

SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

McDonough, GA, 30253 U.S.A.

Manual No. 7006940

Revision IR,

9/28/2006

TP 400-5234-IR-NZ-N