Parts Manual fo
r
E
6
E
E
E
E
TWO-STAGE INTERMEDIATE FRAM
SNOW THROWER
SERIES 5 & 6
MODEL
EI5225
EI75225
EI7524
EI75246
EI8245
EI85245
I5225
I75225
I75246
I8245
I85245
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 2,
McDonough, GA, 30253 U.S.A.
10/3/2006
Manual No. 7006070
TP 400-5038-2-IS-N
s
PAGE GROUP
4
8
10
12
14
16
20
24
30
32
34
UPPER HANDLES, DASH, CONTROLS
CHUTE CRANK CONTROL
COLLECTOR HOUSING (3 Piece Bolted)
DISCHARGE CHUTE
AUGERS, IMPELLER, GEAR CASE, SHAFT
TRACTION DRIVE GROUP
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
WHEELS
DECALS
ELECTRIC START COMPONENTS
Table Of Content
SERIES 5 & 6
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
3
TP 400-5038-2-IS-N
UPPER HANDLES, DASH, CONTROLS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
4
SERIES 5 & 6
UPPER HANDLES, DASH, CONTROLS
p
y
Part No Descri
1 1919438 2 NUT, 5/16-18 Hex Nyloc or 7091298
2 1726727 1 BRACKET, Snow Stick- Lower
3 1921332 4 SCREW, 5/16-18 x 3/4” Hex Head Cap or 7091318
4 7027426 1 CLUTCH CABLE, Auger Drive- RH part number is stamped on cable
5 1726574 1 HANDLE, Upper, Right Hand
6 1722638 1 GRIP, Clutch, RH
7 1726317 2 GRIP, Foam, Black
8 1722460 3 HAIR PIN
9 1666255 1 ROD, Shift, Lower
10 1916622 2 NUT, 1/4-20 2B Hex
11 1916964 3 LOCKWASHER, 1/4” Spring
12 1931317 2 BOLT, 1/4-20 x 2” Short Square Neck Carriage, GR 5
13 1720238 1 ROD, Upper, Shift
14 1668524 2 BLOCK, Pivot
15 1720240 1 WELDMENT, Shift Rod Pivot
16 1715123 1 SPRING, Compression
17 1918452 1 COTTER PIN, .125 x 1.00
18 1668185 2 BUSHING, .500 ID x .750 OD x .25
19 1924361 1 WASHER, 1/2” Flat (.531 ID x 1.250 OD x .08 Thick)
20 1668523 1 WELDMENT, Shift Rod
21 1960705 1 SCREW, 1/4-20 x 2-1/4” Hex Flange Lock
22 1921319 2 WASHER, .250 (.27 ID x .62 OD)
23 1726734 1 KNOB, Tapered - 3/8-16 Internal Thread- Red
24 1726983 1 WELDMENT, Dash
25 1726572 1 HANDLE, Lower
26 7035744 2 WING KNOB, 5/16-18
27 7090391 2 WASHER, 5/16” Internal Tooth Lock
28 1960686 4 NUT, 5/16-18 Hex Flange Nyloc
29 1919326 2 WASHER, .312 (.34 ID x .75 OD) or 7014098
30 1722633 1 ASSEMBLY, Rod w/Pin includes items 32, 47, 54, 55 &
31 1722690 1 SPRING, Compression
32 1960519 1 PUSH NUT
33 1722630 1 ROD, Hold Down
34 1960662 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
35 1722667 1 GRIP, Clutch, LH
36 1923358 2 NUT, 1/4-20 Hex Centerlock
37 1715655 2 SPACER, Handle
tionItem Qt
Note
56.
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
5
TP 400-5038-2-IS-N
UPPER HANDLES, DASH, CONTROLS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
6
SERIES 5 & 6
UPPER HANDLES, DASH, CONTROLS
p
y
Part No Descri
38 1726573 1 HANDLE, Upper, Left Hand
39 1922837 2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap
40 1715654 2 SPACER, .268 ID x .394 x .165
41 1960671 2 SCREW, 1/4-20 x 3/4” Pan Head Torx Self-Tap
42 1921221 5 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
43 1722631 1 LEVER, Pivot
44 1920397 2 NUT, 1/4-20 Hex Nyloc
45A 7075909 1 SNOW STICK
45B 1733209 1 SNOW STICK w/Brush replaces 7075909
46 7091267 1 NUT, #10-24 Hex Center Lock
47 1722632 1 ROD, Hand Control not shown; part of item 30
48 7071895 1 HOLDER, Snostik- Upper
49 7027425 1 CLUTCH CABLE, Ground Drive- LH parts number is stamped on
50 7091189 4 BOLT, 5/16-18 x 2” Curved Head Square Neck GR 2
51 7090011 1 WASHER, #10 Internal Tooth Lock
52 7091266 1 SCREW, #10-24 x 2” Hex Washer Head Machine, GR 5
53 1917356 4 LOCKWASHER, Spring .312 or 7091315
54 1722635 1 BUSHING, .250 ID x .375 OD x .750 not shown; part of item 30
55 1722634 1 PIN, Clevis not shown; part of item 30
56 1722613 1 SPRING, Compression not shown; part of item 30
tionItem Qt
Note
cable
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
7
TP 400-5038-2-IS-N
CHUTE CRANK CONTROL
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
8
SERIES 5 & 6
CHUTE CRANK CONTROL
p
y
Part No Descri
1 1960093 1 PUSH NUT, Pal. .375 Dia. Stud Cap
2 1714084 1 KNOB, Spinner
3 1667588 3 BUSHING, .376 x .437 x .20
4 7028152 1 ROD, Chute, Upper
5 1960074 1 CLIP, .093 Dia. Hair Pin
6 1720577 1 SPLICE, Chute Handle
7 1926228 1 SPRING PIN, .156 x 1.000
8 1726939 1 ROD, Chute Lower
9 1918452 1 COTTER PIN, .125 x 1.00
10 1718793 1 BRACKET, Universal Gear
11 1921319 3 WASHER, .250 (.27 ID x .62 OD)
12 1960518 2 RETAINER, 1/4” Bolt
13 1960252 2 BOLT, 1/4-20 x 5/8” Short Square Neck Carriage
14 1718593 2 GEAR, Universal
15 1960103 1 WASHER, 3/8” Flat- Black
16 1916168 1 SPRING PIN, .125 x .750
17 7028159 1 WORM SHAFT
18 1960294 2 NUT, 1/4-20 Hex Flange Lock
19 7014001 1 ROLL PIN, 1/8 x 3/4”
20 7021828 1 WORM
21 7011724 1 WASHER, .44 x .78 x .025 Curved
22 7028162 1 BRACKET, Worm
23 7091070 1 NUT, 5/16-18 Hex Flange Lock
24 7091138 1 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR 5
25 7090539 1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
9
TP 400-5038-2-IS-N
COLLECTOR HOUSING (3 Piece Bolted)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
10
SERIES 5 & 6
COLLECTOR HOUSING (3 Piece Bolted)
p
y
Part No Descri
1 7072542 1 END PLATE, RH- Auger Housing- Red
2 7072547 1 WELDMENT, Auger Housing - 22” - Red
2 7072567 1 WELDMENT, Auger Housing - 24” - Red
3 1930659 3 RETAINER NUT, 5/16-18
4 7072544 1 END PLATE, LH- Auger Housing- Red
5 7300099 1 BLADE, Scraper- 22” replaces 1675080
5 7200098 1 BLADE, Scraper- 24” replaces 1725352
6 1726457 2 BEARING, Auger
7 1665982A 1 RETAINER, Bearing
8 108202 1 BALL BEARING
9 7072552 2 SKID SHOE, Reversible- Red or 1727854
10 1916965 4 WASHER, 3/8” Split Lock or 7091320
11 1931315 12 BOLT, 1/4-20 x 1/2” Short Square Neck Carriage, GR 5 or 7091604
12 7090204 3 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or 1925205
13 1930641 12 NUT, 1/4-20 Hex Flange Lock Large
14 1960711 4 BOLT, 3/8-16 x 3/4” Square Neck Carriage or 7091923
15 1924940 4 WASHER, 3/8” Flat or 7090122
16 1960687 4 NUT, 3/8-16 Hex Nyloc
17 7091742 6 SCREW, 5/16-18 x 1” Hex Washer Self-Tap
18 7072549 2 CAP, Bearing, Red
19 7091315 3 WASHER, 5/16” Split Lock or 1917356
20 7091208 5 BOLT, 1/4-20 x 7/16” Short Square Neck Carriage, GR 5
21 7091065 5 NUT, 1/4-20 Hex Flange Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
11
TP 400-5038-2-IS-N
DISCHARGE CHUTE
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
12
SERIES 5 & 6
DISCHARGE CHUTE
p
y
Part No Descri
1 7028217 1 CHUTE, Discharge A Chute/Deflector Assy
2 7091021 1 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5
3 7028846 1 DEFLECTOR, Chute
4 7035744 1 WING KNOB, 5/16-18
5 7028253 1 WIRE PIN
6 7039765 1 CHUTE RING
7 7011938 3 RETAINER, Spout
8 7091075 6 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
9 7091077 3 BOLT, 5/16-18 x 5/8” Square Neck Carriage, GR 5
10 7091070 3 NUT, 5/16-18 Hex Flange Lock
11 7091097 1 BOLT, 5/16-18 x 3/4” Square Neck Carriage, GR 5
12 7091076 2 WASHER, .34 x .69 x .08 Flat
13 7091074 1 NUT, 5/16-24 Hex Center Lock, GR B
14 7019692 1 WIRE, Safety used on Euro models
15 7023673 2 PUSH-ON FASTENER, 5/32” Dia. used on Euro models (Arden
16 7032559 2 RETAINER, Safety Wire used on Euro models
17 7091552 6 WASHER, 7/32” Flat used on Euro models
tionItem Qt
Note
(7075321) includes items 1, 3 &
5.
#BV5928)
Footnotes:
For deflector & decal ass'y order 7072058 (domestic) or 7074741 (european).
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
13
TP 400-5038-2-IS-N
AUGERS, IMPELLER, GEAR CASE, SHAFT
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
14
SERIES 5 & 6
AUGERS, IMPELLER, GEAR CASE, SHAFT
p
y
Part No Descri
1 1715091 1 PULLEY, Auger Input
2 7090848 2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or 1928721
3 7012699 2 KEY, 3/16 x 3/4” Woodruff or 7010211
4 1960474 1 SET SCREW, 3/8-16 x 1/2” Square Head
5 1715120A 1 WELDMENT, Impeller
6 1612093 1 OIL SEAL
7 1666425 1 BUSHING
8 936098 1 PIN, Drive-Loc, 3/16 x 1-1/2”
9 1721680 1 COLLAR, Thrust
10 1715580 1 SHAFT, Rolled Worm
11 1670971 1 WASHER, Thrust (.562 ID x 1.000 OD x .030/.032 Thick)
12 1666424 1 FLANGE, Bushing
13 1676027 2 OIL SEAL
14 7091576 6 NUT 1/4-20 Hex replaces 7092126
15 1726732 1 GEAR CASE, LH- Intermediate
16 1721676 1 GASKET, Gear Case
17 1676026 2 BUSHING
18 1726538 1 SHAFT, Auger, 22”/24”
19 1676024 1 GEAR, Worm
20 1726733 1 GEAR CASE, RH- Intermediate
21 7092128 1 PIPE PLUG, 1/8-27 NPTF 3/4 Taper x .31 Long Hex Drive
22 7092125 6 SCREW, 1/4-20 x 7/8” Hex Head Cap, GR 5
23 921133 1 FITTING, Grease
24 1726536 1 WELDMENT, 22” Auger, RH
25 1726535 1 WELDMENT, 22” Auger, LH
26 7023590 2 COTTER PIN, 1/4” Self Locking replaces 7091597
27 1668344 2 SHEAR PIN, .248 ID x 1-3/4” Long
28 1960114 4 WASHER
29 927794 2 RING, External Retaining (for .75 dia. Shaft)
30 7015894 1 KEY, #605 Woodruff
31 1612112 1 TUBE, Low Density Polyethylene Extruded
32 7092127 12 FLAT WASHER, .268 ID x .591 OD x .063 Thick
33 7090052 6 WASHER, 1/4” Split Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
15
TP 400-5038-2-IS-N
TRACTION DRIVE GROUP
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
16
SERIES 5 & 6
TRACTION DRIVE GROUP
p
y
Part No Descri
1 1930601 3 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap or 7090361
2 1673994A 1 BRACKET, Bushing
3 7091302 1 NUT, 3/8-16 Hex, GR 5 or B
4 7091320 1 WASHER, 3/8” Split Lock or 1916965
5 1669256 1 ASSEMBLY, Shift Arm w/Bushing includes weldment (1666213) &
6 1666114 1 BUSHING, Spacer, .380 ID x .750 OD x 1.030 Long
7 7090122 1 WASHER, 3/8” SAE Flat or 1924940
8 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 or 1923701
9 7091138 4 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR 5
10 1722703 2 BALL BEARING, .669 ID x .574 OD
11 1667341 2 RETAINER, Bearing
12 1917356 4 LOCKWASHER, 5/16” Spring or 7091315
13 7090196 7 NUT, 5/16-18 Hex, GR B or 5 or 1917372
14 7072432 1 HEX SHAFT
15 927794 1 RING, External Retaining (for 3/4 Dia Shaft)
16 7091318 3 SCREW, 5/16-18 x 3/4” Hex Head Cap or 1921332
17 1725428 1 DRIVEN DISC or 7018782
18 1665995 1 HUB, Friction Disc
19 1678956 2 COLLAR, Thrust
20 1666207 1 PIN, Slide
21 7091829 2 SET SCREW, 1/4-20 x 1/2 w/Patch Lock or 1724333
22 1667335 1 COLLAR, Set, 1.251 ID x 2.00 OD x .50 Long
23 7072459 1 SPROCKET #35, 12 Tooth
24 1960353 1 WASHER, 1/4 ID x 5/8 OD x .134/.109 Flat or 7091294
25 1916964 1 LOCKWASHER, 1/4” Spring
26 1923341 1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5 or 7091495
27 8021010 1 COLLAR, Set, .756 ID x 1.249 OD x .50
28 7090848 2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or 1928721
29 7072474 1 WELDMENT, Axle & Sprocket
30 7072491 1 CHAIN, Roller, #35, 25.5” Long
31 1715101 1 BUSHING
32 1715253 1 PULLEY, Traction
33 7090951 2 NUT, 5/16-18 Large Head Center Lock or 1935048
34 1665844 2 SPACER, .328 ID x .562 OD x .144/.149 Thick
35 1726778 1 ASSY, Pivot Plate/Hub w/Bearing includes weldment (1726779),
36 7090204 2 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or 1925205
37 1666379 1 WASHER
tionItem Qt
Note
bushing (1669255)
bushing (1666855) & bearing
(1665521)
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
17
TP 400-5038-2-IS-N
TRACTION DRIVE GROUP
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
18
SERIES 5 & 6
TRACTION DRIVE GROUP
p
y
Part No Descri
38 7091214 1 KEY, Hi-Pro, #HP-506 or 930672
39 1719879 1 DRIVE DISC, w/ Spindle
40 1715131 1 ROD, Pivot
41 7091598 1 COTTER PIN, 1/8 x 3/4”
42 7091575 1 NUT, 5/16-18 Hex Nyloc Light or 1919438
43 1919326 2 WASHER, .312 (.34 ID x .75 OD) or 7014098
44 1700473 1 BELLCRANK
45 1666106 1 BUSHING
46 7091908 1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127
47 1924366 1 WASHER, Plain, .75 ID x 1.31.OD x .10
48 7091593 1 COTTER PIN, 3/8” Self Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
19
TP 400-5038-2-IS-N
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
20
SERIES 5 & 6
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
p
y
Part No Descri
1 7090233 4 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5 or 1921515
2 1924874 1 WASHER, 5/16” Flat
3 1715136 1 WIRE, Belt Stop replaced by 7100117 &
4 7090395 3 LOCKWASHER, 5/16” Exterior Tooth or 1920427
51* ENGINE, 5HP Tecumseh Model LH195SA-67427V
6 1726942 1 HOSE, Oil Drain
7 1931277 3 NUT, 5/16-18 Hex Flange Lock- small
8 931277 1 NUT, 5/16-18 Hex Flange Lock
9 1715092 1 ROD, Idler
10 7090844 2 ROLL PIN, 3/16 x 3/4” or 916169
11 7072556 1 WELDMENT, Intermediate Frame- Red
12 1926018 6 SPEED NUT, 1/4-20 U-Type
13 1666001 2 BUSHING, 1.00 long
14 1715559 1 SUPPORT, Tie Bar
15 1929477 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
16 1960251 4 JAM NUT, 3/8-16 Hex Center Lock
17 1924940 3 WASHER, 3/8” Flat or 7090122
18 1674315 2 ROD, Belt Guide
19 1922694 4 NUT, 3/8-16 Hex Nyloc Heavy Thin
20 1715756 1 SUPPORT, Frame
21 7090858 4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or 1924856
22 1715111 1 SUPPORT, Pivot
23 1919381 2 WASHER, 5/16” Flat
24 7091908 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127
25 7091908 1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127
26 7072554 1 COVER, Bottom- Red
27 7090362 9 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
28 1925125 1 WASHER, 7/16” Flat
29 7091598 1 COTTER PIN, 1/8 x 3/4”
30 1715112 1 WELDMENT, Idler Arm
31 1960268 1 BOLT, 3/8-16 x 1-1/4” Short Square Neck Carriage
32 174870 1 SPACER, .377 ID x .75 OD x .312 Long
33 118414 1 PULLEY, Idler
34 1717393 1 BELT, V Groove, 4L Section; 36.00” nom. effective length Auger Drive
35 1715127 1 BELT, V Groove, 3L Section; 35.25” effective length Traction Drive
36 1715118 1 SPRING, Extension
37 1669313 1 PAD, Brake
tionItem Qt
Note
7100118; see Briggs Engine
Page inset
Footnotes:
* NOTE: See your local Tecumseh distributor for engine service parts.
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
21
TP 400-5038-2-IS-N
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
22
SERIES 5 & 6
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
p
y
Part No Descri
38 925160 2 RIVET, Blind
39 7500303 1 ASSEMBLY, Idler Arm w/Brake Pad replaces 1717320; incl. idler arm
40 7091158 1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5
41 1922755 1 WASHER, 3/8” Flat (.41 ID x 1.00 OD x .13 Thick)
42 1668477 1 PULLEY, Idler
43 1725379 1 COVER, Belt
44 1720237 1 SPRING, Idler- Extension
45 7092031 1 JAM NUT, 5/16-24 Hex
46 924819 1 KEY - Hi Pro .125 x .625 HP 504 SAE1035
47 1674325 1 PULLEY, V Groove
48 7090201 2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point
49 1720313 1 PULLEY, 2.75 OD
50 7010061 1 KEY, 3/16 Square x 1”
51 7015861 1 HARNESS CLIP
52 1930645 1 NUT, 3/8-16 Hex Flange Lock Two Way
53 7028090 1 MUFFLER GUARD, Domestic (Tecumseh)
54 7091075 1 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
55 7034169 1 MUFFLER GUARD, Tecumseh Engine (Euro) not shown; Tecumseh #127-18
56 7034254 2 SCREW. Tecumseh Muffler not shown; Tecumseh #42-671
57 7034251 2 LOCK WASHER, Tecumseh Muffler not shown; Tecumseh #36-351
58 7034239 2 WASHER, Tecumseh Muffler not shown; Tecumseh #36-195-1
tionItem Qt
Note
weldment (7400177)
Footnotes:
* NOTE: See your local Tecumseh distributor for engine service parts.
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
23
TP 400-5038-2-IS-N
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
24
SERIES 5 & 6
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
p
y
Part No Descri
1 1921982 4 SCREW, 5/16-24 x 1-1/4” Hex Head Cap, GR 5
2 1924874 1 WASHER, 5/16” Flat
3A 1725424 1 BELT STOP, Wire void; Use 3B & 3C in inset below
3B 7100117 1 BELT GUIDE, LH, Traction Drive Belt
3C 7100118 1 BELT GUIDE, RH, Traction Drive Belt
4 7090395 3 LOCKWASHER, 5/16” Exterior Tooth or 1920427
5A 1 * ENGINE, 8 HP B&S Mod. #12E394-0110-E1
5A 1 * ENGINE, 8 HP Intek (Metric) B&S Mod. #12E396-0111-E1
5B 1 * ENGINE, 7-1/2HP B&S OHV Mod. #12D196-0110-E1
5B 1 * ENGINE, 7-1/2HP B&S OHV Euro Mod. #12D296-0113-E1
5B 1 * ENGINE, 7-1/2HP B&S Euro Mod. #12D194-0114-E1 used on EI75246E
5B 1 * ENGINE, 7-1/2HP B&S OHV Euro Mod. #12D296-0113-E1 used on EI75246
5B 1 * ENGINE, 7-1/2HP B&S Electric Start Mod. #12D194-0115-E1 used on I75246E
5B 1 * ENGINE, 8-1/2HP B&S Intek ES Mod. #15B194-0110-E1
5B 1 * ENGINE, 8-1/2HP B&S Intek Mod. #15B196-0111-E1
6 1726942 1 HOSE, Oil Drain
7 1931277 3 NUT, 5/16-18 Hex Flange Lock- small
8 931277 1 NUT, 5/16-18 Hex Flange Lock
9 1715092 1 ROD, Idler
10 7090844 2 ROLL PIN, 3/16 x 3/4” or 70916169
11 7072556 1 WELDMENT, Intermediate Frame- Red
12 7028260 6 SPEED NUT, 1/4-20 U-Type or 1920618
13 1666001 2 BUSHING, 1.00 long
14 1715559 1 SUPPORT, Tie Bar
15 1929477 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
16 1960251 4 JAM NUT, 3/8-16 Hex Center Lock
17 7090122 4 WASHER, 3/8” SAE Flat or 7090517 or 1924940
18 1674315 2 ROD, Belt Guide
19 1922694 4 NUT, 3/8-16 Hex Nyloc Heavy Thin
19 1960687 4 NUT, 3/8-16 Hex Nyloc
20 1715756 1 SUPPORT, Frame
21 7090858 4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or 1924856
22 1715111 1 SUPPORT, Pivot
23 1919381 2 WASHER, 5/16” Flat
24 7091908 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127
25 7091908 1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127
25 7027174 2 SCREW, 5/16-18 x 2” Hex Head Cap, GR 5
tionItem Qt
Note
Footnotes:
NOTE: * See your local Briggs distributor for engine service parts.
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
25
TP 400-5038-2-IS-N
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
26
SERIES 5 & 6
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
p
y
Part No Descri
26 7072554 1 COVER, Bottom- Red
27 7090362 9 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
28 1925125 1 WASHER, 7/16” Flat
29 7091598 1 COTTER PIN, 1/8 x 3/4”
30 1725369 1 WELDMENT, Idler Arm
31 1960268 1 BOLT, 3/8-16 x 1-1/4” Short Square Neck Carriage
32 174870 1 SPACER, .377 ID x .75 OD x .312 Long
33 118414 1 PULLEY, Idler
34 1717393 1 BELT, V Groove, 4L Sect.; 36.00” nom. effective length Auger Drive
35 1725371 1 V-BELT, 3L, 31.64 effective length Traction Drive
36 1715118 1 SPRING, Extension
37 1669313 1 PAD, Brake
38 925160 2 RIVET, Blind
39 7500303 1 ASSEMBLY, Idler Arm w/Brake Pad was 1717320; incl. items 37, 38
40 7091158 1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5
41 1922755 1 WASHER, 3/8” Flat (.41 ID x 1.00 OD x .13 Thick)
42 1668477 1 PULLEY, Idler
43 1725379 1 COVER, Belt
44 159106 1 SPRING, Extension, .562 O.D. x 4.250 Long
45 7092031 1 JAM NUT, 5/16-24 Hex or 920438
46 924819 1 KEY - Hi Pro .125 x .625 HP 504 SAE1035
47 1674325 1 PULLEY, V Groove
48 7090201 2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point or 1960619
49 1720313 1 PULLEY, 2.75 OD
50 7010061 1 KEY, 3/16 Square x 1” or 70905850
51 7015861 1 HARNESS CLIP
52 1724064 1 CORD, Electric Start
53 1725665 1 GUARD, Muffler used on I8245E, EI8245 &
54 1727032 1 DEFLECTOR, Muffler- B&S Briggs p/n 226462
55 1727033 1 HEX SCREW, Thread Rolling M4 x 0.7 Briggs p/n 810140
56 1930645 1 NUT, 3/8-16 Hex Flange Lock Two Way
57 7300133 1 HEAT SHIELD, 7.5HP B&S Powerbuilt Muffler used on I75225 & I75246E
58 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
59 7091609 1 SCREW, 5/16-24 x 1-1/2” Hex Head Cap, GR 5
60 7090188 8 WASHER, 5/16” Flat
61 7012114 1 BUSHING, Differential Link
62 7090187 5 WASHER, 5/16” Split Lock
63 7090196 4 NUT, 5/16-18 Hex, GR 5 or B
tionItem Qt
Note
I85245E
Footnotes:
NOTE: * See your local Briggs distributor for engine service parts.
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
27
TP 400-5038-2-IS-N
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
28
SERIES 5 & 6
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
p
y
Part No Descri
64 7090391 2 WASHER, 5/16” Internal Tooth Lock
tionItem Qt
Note
Footnotes:
NOTE: * See your local Briggs distributor for engine service parts.
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
29
TP 400-5038-2-IS-N
WHEELS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
30
SERIES 5 & 6
WHEELS
p
y
Part No Descri
1 1666969 2 KLIK- PIN, .310 ID x 1-3/4” Long
2 172353 1 VALVE STEM AND CAP per tire assembly
3 1664090 1 TUBE, Tire per tire assembly (optional)
4 1723286 1 RIM, 6 x 3.25 (Weldment) per tire assembly
5 7027866 1 TIRE, 15 x 5.00-6, 2 Ply, Carlisle Snow Hog per tire assembly
6 7041271 2 ASSY, Tire and Wheel, 15 x 5.00-6 Carlisle Sno Hog includes items 2, 4 5
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
31
TP 400-5038-2-IS-N
DECALS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
32
SERIES 5 & 6
DECALS
p
y
Part No Descri
1 1726946 1 DECAL, Dashboard- RH used on Domestic Models
1 1727023 1 DECAL, Dashboard- RH- Euro
2 1715557 1 DECAL, Shift Pattern
3A 1727020 1 DECAL, Dashboard- LH used on Domestic Models
3B 1727021 1 DECAL, Dashboard- LH- Euro
3C 7100821 1 DECAL, Dashboard, Top, LH
3D 7100822 1 DECAL, Dashboard, Top, LH (Euro)
4 1726721 1 DECAL, Dash Front - SNAPPER
5 1 *DECAL, OPEI
6A 1716532 1 DECAL - Danger, Auger used on Domestic Models
6B 1727208 1 DECAL, CE- Auger Warning used on European Models
7 1727027 1 DECAL, Stripe- SNAPPER (5hp, 22”)
7 1727028 1 DECAL, Stripe- SNAPPER (8hp, 24”) not shown; similar to above decal
7 7100116 1 DECAL, Stripe- SNAPPER (7.5hp, 22”) not shown; similar to above decal
7 7100119 1 DECAL, Stripe- SNAPPER (8.5hp, 24”) not shown; similar to above decal
8A 1733057 1 DECAL, Danger, Chute/Deflector
8B 7071880 1 DECAL, Danger, Chute/Deflector
8C 1727207 1 DECAL, Chute Warning
9 1 *I.D. Tag
10 1722867 1 DECAL, Lube- Controls
11 7074136 1 DECAL, Sound 105
12 7029776 1 DECAL, Euro Community (CE)
13 7011279 1 DECAL, 2005 Year of Manufacture not shown
13 7100611 1 DECAL, 2006 Year of Manufacture
14 7100790 1 DECAL, Dash Front- Snapper used on I75246E & EI75246E
15 7100703 1 DECAL, Stripe- Snapper (7.5 24”)
tionItem Qt
Note
models
Footnotes:
*Not a service part
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
33
TP 400-5038-2-IS-N
ELECTRIC START COMPONENTS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
34
SERIES 5 & 6
ELECTRIC START COMPONENTS
p
y
Part No Descri
7600016 1 KIT, Electric Start, 230 volt (incl. items 1 thru 6 below)
1 7011263 1 STRAP, Ground (not shown) B&S # 226756
2 7011264 1 CLAMP, Regulator (not shown) B&S # 393514
3 7011265 1 BRACKET, Regulator (not shown) B&S # 222934
4 7011267 1 SCREW, Hex Head B&S # 95630
5 7011268 2 BOLT, 5/16-18 x 3/4” Hex Head Cap B&S # 93343
6 7011266 1 CLIP, Speed B&S # 95629
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
35
TP 400-5038-2-IS-N
Parts Manual fo
r
TWO-STAGE INTERMEDIATE FRAME
SNOW THROWER
SERIES 5 & 6
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Manual No. 7006070
Revision 2,
10/3/2006
TP 400-5038-2-IS-N
Loading...