Parts Manual fo
r
S
V
FIELD & BRUSH MOWER
SERIES 0
MODEL
FB13250B
FB13250B
FB15250KW
COPYRIGHT ©2005
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 1,
McDonough, GA, 30253 U.S.A.
8/30/2005
Manual No. 7006933
TP 400-5009-1-CW-N
s
PAGE GROUP
4
8
12
14
16
18
20
22
HANDLE PARTS GROUP
ENGINE DECK GROUP
MOWER DECK PARTS GROUP
DECALS GROUP
ELECTRICAL & MISC. GROUP
WIRING HARNESS GROUP
WIRING SCHEMATIC
Hardware Identification & Torque Specifications
Table Of Content
SERIES 0
Manual No. 7006933FIELD & BRUSH MOWER
3
TP 400-5009-1-CW-N
HANDLE PARTS GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
4
SERIES 0
HANDLE PARTS GROUP
p
y
Part No Descri
1 1719965 1 GRIP, Handle
2 7058960 1 LEVER, Blade Clutch Engage (weldment) replaces 1723595
3 7027802 1 CABLE, Throttle, Kawasaki part number stamped on cable
3 7027394 1 CABLE, Throttle, Briggs part number stamped on cable
4 7014871 2 LUBE FITTING, 3/16” hole
5 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
6 7029167 1 DECAL, Throttle, Brush Cutter see Decals group
7 1723550 1 BRACKET, Blade Engage Lock
8 7091318 10 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
9 7028200 1 SWIVEL, Adjustable, 5/16-18 thread
10 7059204 1 LEVER, Transmission Drive (weldment) replaces 1723573
11 7091601 15 NUT, 5/16-18 Hex Flange Lock, GR 5
12 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
13 1723553 1 CONTROL DECK & DASH PANEL (weldment)
14 7091813 4 SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5
15 7091298 8 NUT 5/16-18 Hex Nyloc
16 7011791 3 RETAINER, 5/16” Bolt
17 7072487 1 BRACKET, Handle Pivot, RH
18 7023354 1 SWITCH, Seat NC
19 1723569 2 HANDLE, Lower
20 1723564 1 SPRING, Safety Return
21 1723561 1 WELDMENT, Safety Bar
22 7044927 1 BRACKET, Safety Bar Pivot, LH replaces 1723566
23 7033736 1 HANDLE, Upper was 1723572
24 1719968 1 COVER, Foam was 1723568
25 7090209 6 SCREW, 5/16-18 x 1” Hex Head Cap, GR 2
26 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
27 1723570 2 BEARING, 3/4 I.D.
28 1725232 1 WELDMENT, Drive Engagement Bar
29 1725233 1 GRIP, Reverse Handle
30 7090122 2 WASHER, 3/8 SAE Flat
31 7091518 2 NUT, 3/8-24 Hex Nyloc
32 7091294 8 WASHER, .28 x .63 x .06 Flat
33 7091310 2 HAIR PIN, #13
34 1723554 2 BALL JOINT, Type R (5/16-24 thread)
35 1723556 1 NUT, 3/8-24LH Hex Jam
36 1723557 1 BALL JOINT LH (3/8-24 LH thread)
tionItem Qt
Note
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
5
TP 400-5009-1-CW-N
HANDLE PARTS GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
6
SERIES 0
HANDLE PARTS GROUP
p
y
Part No Descri
37 7092031 1 NUT, 5/16-24 Hex Jam
38 1723555 1 ROD, Trans. Engage, Lower (3/8-24 LH & 5/16-24 threads)
39 1723351 1 BRACKET, Deck Safety Switch
40 1723552 1 SWITCH, Deck Safety
41 1723662 1 BOLT, 1/2 x 1-3/16 to 3/8-16 Shoulder
42 7041868 1 SPACER, Transmission, Express
43 7090188 1 WASHER, 5/16” SAE Flat
44 1723596 1 BRACKET, Clutch Engage Lever
45 7091908 4 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5
46 7091603 4 NUT, 1/4-20 Hex Nyloc
47 7010745 1 BALL JOINT, 3/8-24 Thread
48 1725231 1 ROD, Trans. Engage, Upper (3/8-24 thread)
49 7076938 1 SCREW, 5/16-18 x 2-1/4” Hex Head Cap, GR 5
50 7029495 2 CAP, Push Plastic
51 7012080 3 CABLE TIE, 7”
52 1723616 1 BRACKET, Fuel Tank
53 7091619 1 NUT, 3/8-16 Hex Flange Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
7
TP 400-5009-1-CW-N
ENGINE DECK GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
8
SERIES 0
ENGINE DECK GROUP
p
y
Part No Descri
1 7091318 10 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
2 1723549 1 PLATE, Clutch Cover
3 7091511 4 NUT, 5/16-18 Hex, GR 5 or B
4 7090187 18 WASHER, 5/16” Split Lock
5 1704723 2 CAP, Black
6 1723803 1 DECK, Engine (weldment)
7 7091302 24 NUT, 3/8-16 Hex, GR 5 or B
8 7091320 22 WASHER, .38 x .68 x .09 Split Lock
9 1723806 1 BOSS, Idler Arm Pivot
10 1723805 2 SLEEVE BUSHING, 3/4 ID
11 1723804 1 IDLER ARM, Transmission (weldment)
12 1723592 1 COVER, Engine Back
13 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 engine mount bolts
14 7090001 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
15 1723807 1 SPRING, Idler
16 1723808 1 ROD, Idler Tension (3/8-16 thread)
17 7090122 9 WASHER, 3/8 SAE Flat
18 7092055 1 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
19 1723583 1 PULLEY, Idler
20 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5 was 91553 (1-3/4” long)
21 1723591 1 PLATE, Lower Handle Mount
22 7091619 12 NUT, 3/8-16 Hex Flange Lock or 90613
23 7076941 2 SCREW, 3/8-16 x 1-1/4” Hex Head Cap, GR 5
24 7091304 7 SCREW, 3/8-16 x 1 Hex Head Cap, GR 5
25 1723585 1 SPACER, Engine Shaft
26 1723586 1 PULLEY, Blade Clutch Drive
27 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
28 1723588 1 PULLEY, Trans. Drive
29 7091807 1 WASHER, 7/16” Flat (heavy duty)
30 7091301 1 WASHER, 7/16” Split Lock
31 1723589 1 CAPSCREW, 7/16-20 x 1-12” Socket Head
32 1723620 1 TRANSAXLE
33 1723590 1 KEY, 1/4” Square x 2-1/8” (engine shaft)
34 7072386 2 KEY, 3/16” Square x 2-3/16”
35 7029738 2 RETAINING RING, 3/4” External
36 7031965 4 WASHER, 3/4” I. D. Thrust
37 1723580 1 DRIVE WHEEL, Left not shown
tionItem Qt
Note
Footnotes:
**Purchase engine & engine parts other than those listed from engine service outlets.
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
9
TP 400-5009-1-CW-N
ENGINE DECK GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
10
SERIES 0
ENGINE DECK GROUP
p
y
Part No Descri
38 1723581 1 DRIVE WHEEL, Right
39 7091501 1 SCREW, 3/8-16 x 2-1/2” Hex Head Cap, GR 5
40 1723579 1 PULLEY, Blade Clutch Idler
41 1723577 1 IDLER BOSS
42 1723576 1 ROD, Blade Clutch Idler Tensioning (3/8-16 thread)
43 7076938 4 SCREW, 5/16-18 x 2-1/4” Hex Head Cap, GR 5
44 1723575 1 HANGER, Trans. Forward Mount
45 7072520 1 BRACKET, Clutch Support
46 1723622 1 PLATE, Lock Engage
47 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
48 1723621 1 BRACKET, Lock Lever (weldment)
49 7091536 1 SCREW, 1/4-28 x 5/8” Hex Head Cap, GR 8
50 7090052 1 WASHER, 1/4” Split Lock
51 7091294 3 WASHER, .28 x .63 x .06 Flat
52 1723614 1 **ENGINE, Briggs 13.5HP (not shown) model 21B977, type 0120, trim
52 1723615 1 **ENGINE, Kawasaki 15HP (not shown) model FH451V, type AS02
53 7072515 1 BRACKET, Fuel Tank Bottom (not shown) Briggs part# 225903
tionItem Qt
Note
E1
Footnotes:
**Purchase engine & engine parts other than those listed from engine service outlets.
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
11
TP 400-5009-1-CW-N
MOWER DECK PARTS GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
12
SERIES 0
MOWER DECK PARTS GROUP
p
y
Part No Descri
1 7091511 10 NUT, 5/16-18 Hex, GR 5 or B
2 7090187 10 WASHER, 5/16” Split Lock
3 1723532 1 WELDMENT, Front Bumper
4 1723533 23 CHAIN CURTAIN
5 7091540 3 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 for bumper rear holes
6 1723534 1 BRACKET, Chain Curtain
7 1723535 1 ROD, Chain Curtain Mounting
8 7091304 4 SCREW, 3/8-16 x 1 Hex Head Cap, GR 5
9 7091320 9 WASHER, .38 x .68 x .09 Split Lock
10 1723536 1 LEFT SKID, Blade Deck (weldment) not shown
11 1723537 1 RIGHT SKID, Blade Deck (weldment)
12 7091302 8 NUT, 3/8-16 Hex, GR 5 or B
13 7091318 4 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
14 1723538 1 BRACKET, Anti-Torque
15 1723657 1 SPRING, Clutch
16 1723539 1 ROD, Blade Clutch Engagement (5/16-18 threaded)
17 7091497 5 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
18 -- 1 WASHER, 7/16 I.D. x 1-1/2” Flat (Heavy Duty) this fastener is furnished with
19 1723540 1 ASSEMBLY, Clutch Brake (Noram part no. CB84S)
20 -- 1 SCREW, 5/16-18 x 1” Hex Head Cap this fastener is furnished with
21 -- 1 NUT, 5/16-18 Hex Center Lock this fastener is furnished with
22 1723541 1 SPACER, Clutch
23 7090122 3 WASHER, 3/8” SAE Flat
24 1723542 1 ASSEMBLY, Blade Spindle
25 1723543 1 CHANNEL, Cutting Blade Reinforcement
26 1723544 1 CUTTING BLADE
27 7090333 1 WASHER, 5/8” Split Lock
28 1725227 1 CAPSCREW, 5/8-11 x 1-1/2” Socket
29 1723546 1 DELFECTOR, Discharge (weldment)
30 7090188 2 WASHER, 5/16” SAE Flat
31 1723547 1 COVER, Discharge (weldment)
32 1723548 1 BLADE DECK
33 7091908 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 for bumper front holes
34 7028620 4 SPACER, .340 I.D. x .630 O.D. x .310 thick
tionItem Qt
Note
the clutch
the clutch
the clutch
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
13
TP 400-5009-1-CW-N
DECALS GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
14
SERIES 0
DECALS GROUP
p
y
Part No Descri
1 7013010 3 DECAL, Danger, Cut Finger (CPSC)
2 7075893 1 DECAL, Personal Protection
3 7028490 1 DECAL, Warning, Brush Cutter
4 7073647 2 DECAL, Caution, Guard Catcher
5 1725229 1 DECAL, Transmission Drive
6 7028349 1 DECAL, Ignition/Cutting Blade
7 7029167 1 DECAL, Throttle, Brush Cutter
8 1725230 1 DECAL, Speed Adjuster
9 7073594 1 DECAL, Caution, Open Belt Drive
10 7075760 1 DECAL, SNAPPER, 8” long
11 7029331 1 DECAL, 25”
12 7071916 1 DECAL, SNAPPER, 14-1/2” long
tionItem Qt
Note
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
15
TP 400-5009-1-CW-N
ELECTRICAL & MISC. GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
16
SERIES 0
ELECTRICAL & MISC. GROUP
p
y
Part No Descri
1A 7044922 1 WIRE HARNESS, Briggs also shown on previous page
1B 1724057 1 WIRE HARNESS, Briggs also shown on previous page
1C 7044926 1 WIRE HARNESS, Kawasaki also shown on previous page
1D 1724058 1 WIRE HARNESS, Kawasaki also shown on previous page
2 1723618 1 FUEL TANK, Auxilliary
3 7012222 2 CLAMP, Fuel Hose
4 7023506 1 BEZEL
5 7012080 2 CABLE TIE, 7”
6 1723635 1 BRACKET, Battery Hold Down
7 7091314 2 WASHER, 1/4” Internal Lock
8 1723563 1 SWITCH, Bail (not shown) used on early production units
9 1723637 1 CABLE, Battery Positive to Solenoid
10 7090052 3 WASHER, 1/4” Split Lock
11 1723636 1 SCREW, Tek #12 x 3/4” Hex Head Cap
12 1723639 1 CABLE, Solenoid to Starter
13A 7075622 1 SOLENOID - Super Trombetta - 2 Terminal GV3031730
13B 1723641 1 SOLENOID, Single Pole Simplicity solenoid used on early
14 1723631 1 SWITCH, Keyed Start
15 1723619 1 AUX FUEL LINE w/Clamps used on 13.5hp Briggs & 15hp
16 7091495 2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
17 7091576 2 NUT, 1/4-20 Hex, GR 5 or B
18 1723629 1 BELT, Blade Clutch 5L Sect.; 67.40 effective length
19 1723630 1 BELT, Transmission AX Sect.; 30.10 effective length
20 7029130 1 BATTERY, 12V, 3 Amp, 190 Cold Cranking Amp (Incl. Drain
Tube)
21 1725226 1 CABLE, Battery Negative to Ground
22 7029332 1 GROUND WIRE, 16 Ga., Green, 19” long
tionItem Qt
Note
only
production
Kawasaki
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
17
TP 400-5009-1-CW-N
WIRING HARNESS GROUP
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
18
SERIES 0
WIRING HARNESS GROUP
p
y
Part No Descri
1A 7044922 1 WIRE HARNESS, Briggs
1B 1724057 1 WIRE HARNESS, Briggs Simplicity p/n used on early
1C 7044926 1 WIRE HARNESS, Kawasaki
1D 1724058 1 WIRE HARNESS, Kawasaki Simplicity p/n used on early
tionItem Qt
Note
production
production
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
19
TP 400-5009-1-CW-N
WIRING SCHEMATIC
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
20
SERIES 0
WIRING SCHEMATIC
p
y
Part No Descri
* * 1 Wiring Schematic includes 4 harness* *7044922, 1724057, 7044926 &
tionItem Qt
Note
1724058
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
21
TP 400-5009-1-CW-N
Hardware Identification & Torque Specifications
Manual No. 7006933 FIELD & BRUSH MOWER
TP 400-5009-1-CW-N
22
SERIES 0
Hardware Identification & Torque Specifications
p
y
Part No Descri
-- -- Chart for hardware I.D. & torque specs.
tionItem Qt
Note
Footnotes:
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0
23
TP 400-5009-1-CW-N
Parts Manual fo
r
FIELD & BRUSH MOWER
SERIES 0
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
COPYRIGHT ©2005
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Revision 1,
8/30/2005
Manual No. 700693 3
TP 400-5009-1- C W-N
Loading...