Safety Instructions & Operator’s Manual for
EUROPEAN
21” STEEL DECK
WALK MOWERS
SERIES 17
PROPELLED MODELS
EP2167517BV
ERP2167517BV
MODEL NUMBER EXPLANATION
E P 21 675 17 BV
MODEL DESIGNATION ENGINE DESIGNATION
SELF-PROPELLED SERIES DESIGNATION
CUTTING WIDTH ENGINE HORSE POWER
E – European Model P – Self Propelled Model 17 - Series Designation
R – Recycling Model B – Briggs & Stratton
21 – 21” Cutting Width V – Overhead Valve
675 – 6.75 HP (Engine Horse Power)
Thank you for buying a SNA PPER Produ ct! B efor e ope ratin g you r Walk B ehin d, r ead th is m an ual c areful ly a nd pay
particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power
equipment can be d an g e r ou s if us ed improperly. Also ke ep in mind that SAFETY r equires carefu l use in ac co rdance
with the operating instructions and common sense.
COPYRIGHT © 2002
SNAPPER INC.
ALL RIGHTS RESERVED
MANUAL No. 7-4937 (I.R. 6/07/02)
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that
can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious
injury or death to the operator or other persons. The owner of the machine must understand these instructions
and must allow only persons who understand these instructions to operate machine . Each person operating
the machine must be of sound mind and body and must not be under the influence of any substance, which
might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your
dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER,
McDonough, Georgia 30253. Phone: (1-800-935-2967).
PROTECTION FOR CHILDREN
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you
last saw them.
1. KEEP children out of the mowing area and
under the watchful care of a responsible adult.
2. DO NOT allow children in yard w hen machine i s
operated and turn machine OFF if anyone
enters the area.
3. DO NOT allow pre-teenage children to operate
machine.
4. ALLOW only responsible adults & teenagers
with mature judgment under close adult
supervision to operate machine.
5. DO NOT pull mower backwards unless
absolutely necessary. LOOK and SEE behind
and down for children, pets and hazards before
and while backing.
6. USE EXTRA CARE when approaching blind
corners, shrubs, trees, or other objects that
may obscure vision.
SLOPE OPERATION
1. Slopes are a major fact or related to slip and f all
accidents, which can result in severe inju ry. All
slopes require extra caution. If you feel une asy
on a slope, DO NOT mow it.
2. Mow across slopes, never up-and-down.
Exercise extreme CAUTION when changing
directions on slopes. DO NOT mow steep
slopes or other areas where stabilit y or traction
is in doubt.
3. Use extra care with grass catchers or other
attachments; these affect the handling and the
stability of the machine.
PREPARATION
1. Read, understand, and follow instructions and
warnings in this manual and on the mower,
engine and attachments. Know the controls and
the proper use of the mower before starting.
2. Only mature, responsible persons shall operate
the machine and only after proper instruction.
PREPARATION
(Continued From Previous Column)
3. Data indicates that operators ag e 60 and above,
are involved in a large percentage of mowerrelated injuries. These operators should
evaluate their ability to operate the mower
safely enough to protect themselves and others
from serious injury.
4. Handle fuel wit h extra car e. Fuels are f lammable
and vapors are explosiv e. Use o nl y an app rov ed
fuel container. DO NOT remov e fuel cap or add
fuel with engine running. Add fuel outdoors
only with engine stopped and cool. Clean
spilled fuel and oil from machine. DO NOT
smoke.
5. Check the area to be mowed and remove all
objects such as toys, wire, rocks, limbs and
other objects that could cause injury if thrown
by blade or interfere with mow ing. Also note the
location of holes, stumps, and other possible
hazards.
6. Keep people and pets out of the mowing area.
Immediately, STOP Blade, Stop engine and Stop
mower if anyone enters the area.
7. Check shields, deflectors, switches, blade
controls and other saf ety devices frequ ently for
proper operation and location.
8. Make sure all safety decals are clearly legible.
Replace if damaged.
9. Protect yourself when mowing and wear safety
glasses, long pants and substantial footwear.
DO NOT mow barefooted or with sandals.
10. Know how to STOP blade and engine quickly in
preparation for emergencies.
11. Use extra care when loading or unloading the
machine into a trailer or truck.
12. Check grass catcher components frequently for
signs of wear or deterioration and replace as
needed to prevent injury from thrown objects
going through weak or torn spots.
3
IMPORTANT SAFETY INSTRUCTIONS
OPERATION
1. DO NOT put hands or feet near or under
rotating parts. Keep clear of discharge area
while engine is running.
2. STOP engine when crossing gravel drives,
walks, or roads, and under any conditions
where thrown objects might be a hazard.
3. Mow only in daylight or good artificial light.
4. DO NOT operate mower while under the
influence of alcohol or drugs.
5. After striking a foreign object or if mower
vibrates abnormally, STOP the engine,
disconnect and secure s park plug wire. Inspect
the mower for any damage and repair the
damage.
6. DO NOT mow near drop offs, ditches or
embankments. Operator could lose footing or
balance.
7. STAY ALERT for holes and other hidden
hazards. Tall grass can hide obstacles. Keep
away from ditches, washouts, culverts, fences
and protruding objects.
8. DO NOT mow on wet grass. Always be sure of
your footing. Keep a firm hold on the handle
and walk, never run. Slipping could cause
injury.
9. DO NOT leave the machine with the engine
running. STOP BLADE and STOP ENGINE
before leaving the operators position for any
reason.
10. Before cleaning, repairing or inspecting make
certain engine, blade and all moving parts have
STOPPED. Disconnect and secure spark plug
wire away from plug to prevent accidental
starting.
11. STOP engine and w ait until the blade comes to
complete STOP before removing grass bag
and/or clearing grass.
12. DO NOT operate mower with out the ent ire grass
catcher or guards in place. DO NOT point
discharge at people, passing cars, windows or
doors.
13. Slow down before turning.
14. Watch out for traffic when near or crossing
roadways.
15. DO NOT operate engine in enclosed areas.
Engine exhaust gases contain carbon
monoxide, a deadly poison.
MAINTENANCE AND STORAGE
1. DO NOT store mower or fuel container inside
where fumes may re ach a n o pen flame, spark or
pilot light such as in a water heater, furnace,
clothes dryer or other gas appliance. Allow
engine to cool before storing machine in an
enclosure. Store fuel container out of reach of
children in a well ventilated, unoccupied
building.
2. Keep mower and engine f ree of g rass, leav es or
excess grease to reduce f ire hazard and engine
overheating.
3. When draining fuel tank, drain fuel into an
approved container outdoors and away from
open flame.
4. Keep all bolts, especia lly blade bolts, nuts and
screws properly tight . Check that all cot ter pins
are in proper position.
5. Always provide adequate ventilation when
running engine. Engine exhaust gases contain
carbon monoxide, a deadly poison.
6. Service engine and make adjustments only
when engine is stopped. Removed spark plug
wire from spark plug and secur e wire away from
spark plug to prevent accidental starting.
7. DO NOT change engine governor speed
settings or overspeed engine.
8. Check grass bag assembly frequently for wear
or deterioration to avoid thrown objects and
exposure to moving parts. Replace with new
bag if loose seam s or tea rs are evident. Replace
slider or bag adapter if broken or cracked.
9. Mower blades are sharp and can cut. Wrap the
blades or wear heavy leather gloves and use
CAUTION when handling them.
10. DO NOT test for spark by grounding spark plug
next to spark plug hole; spark plug could ignite
gas exiting engine.
11. Have machine serviced by an authorized
SNAPPER dealer at least once a year and have
the dealer install any new safety devices.
12. Use only genuine SNAPPER replacement parts
to assure that original standards are
maintained.
4
TABLE OF CONTENTS
IMPORTANT
The figures and illustrations in this manu al are provided for reference only and
may differ from your specific model. Contact your Snapper dealer if you have
IMPORTANT SAFETY INSTRUCTIONS..............................................2 - 3
TABLE OF CONTENTS............................................................................ 4
SECTION 1 - FAMILIARIZATION............................................................. 5
SECTION 2 - OPERATING INSTRUCTIONS.........................................6-9
Pre-start Checklist............................................................................................... 6
Starting & Stopping Engine & Blades................................................................ 6
Starting & Stopping Wheel Drive ....................................................................... 7
Handle Height Adjustment.................................................................................. 7
Cutting Height Adjustment ................................................................................ .7
Recycling Operation............................................................................................ 8
Installation of Grass Catcher.............................................................................. 8
Installation of Discharge Deflector & Recycling Cover ................................... 9
SECTION 3 - MAINTENANCE INSTRUCTIONS ...............................10-11
Change Engine Oil............................................................................................. 10
Check Transmission Grease ....................................................................... 10-11
Check Mower Blade........................................................................................... 11
Check Engine Drive Belt ................................................................................... 11
Check Transmission Poly-V Belt...................................................................... 11
Service - Annually.............................................................................................. 11
Engine.............................................................................................................. 11
Air Filter........................................................................................................... 11
Engine Oil........................................................................................................ 11
Storage Procedure............................................................................................. 11
SECTION 4 - ADJUSTMENTS AND REPAIR....................................12-18
Mower Blade Replacement ............................................................................... 12
Blade Sharpening .........................................................................................12-13
Wheel Drive Control Adjustment...................................................................... 13
Driven and Drive Disc Service.......................................................................... 14
Cleaning Drive Disc and Driven Disc ........................................................... 14
Drive Spring Repair/Replacement ................................................................ 14
Driven Disc Adjustment............................................................................14-15
Driven Disc Replacement ......................................................................... 15-16
Driven Disc Bearing Replacement................................................................ 16
Hex Shaft Bearing Replacement................................................................... 17
Belt Service ........................................................................................................ 17
Engine Drive Belt Replacement ............................................................... 17-18
Transmission Poly-V Belt Replacement....................................................... 18
TROUBLESHOOTING ............................................................................ 19
SERVICE SCHEDULE ............................................................................ 20
Maintenance/Replacement Parts...................................................................... 20
DECAL IDENTIFICATION..................................................................21-22
WARRANTY............................................................................................ 23
questions.
5
Section 1 - FAMILIARIZATION
WHEEL DRIVE
BLADE
GROUND SPEED
ENGINE
ROPE
HANDLE
GRASS
GRASS BAG
FUEL FILLER
FRONT HEIGHT
ENGINE PRIMER
OIL FILL CAP
START
HANDLE
CONTROL
SPEED
CONTROL
KNOB
BAG
1.1 INTRODUCTION
This manual has been prepared for the operat ors of
the SNAPPER WALK BEHIND MOWERS. Its
purpose, aside from recommending operating and
routine service requirements, is to promote safety
through the use of accepted operating practices.
Read, Understand and Follow the “IMPORTANT
SAFETY INSTRUCTIONS” on Pages 2 & 3 of this
manual and all safet y messages on the mower and
attachments before operating the mower.
CONTROL
CONTROL
ADAPTOR
FIGURE 1.1
ENGINE SPEED CONTROL
FAST
SLOW
CAP
AND DIPSTICK
ADJUSTMENT
LATCHES
1.2 NOMENCLATURE
The nomenclature draw ing abo ve, Figure 1. 1, sho ws
the essential parts of the SNAP PER W ALK BEHIND
MOWERS. It is r ecommended that all operat ors of
the mower become thoroughly familiar with the
controls, parts and operation of the mower before
operating. Specif ic details involving the engine are
found in the separate eng in e o wner ’s manual. Study
these manuals before operating and keep both
handy for future reference.
6
Section 2 - OPERATING INSTRUCTIONS
WHEEL DRIVE
BLADE
BLADE
ENGINE SPEED
ROPE
2.1 PRE-START CHECK LIST
Make the following checks and perform the service
required before ea ch start -up.
2.1.1. Check guards, deflectors, grass bag, adapter
and covers to make sure all are in place and securely
tightened.
2.1.2. Check blade control and wheel drive control
to insure they work freely. See Figure 2.1.
2.2 STARTING & OPERATION
2.2.1. ENGINE & BLADE
(Primer Models)
1. Move engine speed contro l to the “Fast” (Rabbit)
position. See Figure 2.3.
NOTE: Stop the engine (and blade) by releasing the
blade control.
CONTROL
CONTROL
FIGURE 2.1
2.1.3. Check cutting height. Adjust to desired
height.
2.1.4. Check engine oil and add oil as needed to bring
level up to the full mark. Refer to Engine Owner’s
Manual for oil specificatio ns. See Fig ure 2.2.
FIGURE 2.2
2.1.5. Add fuel to tank after pushing the mower
outside where fumes can safely dissipate. Make
sure cap is tightened af ter ref ueling. Refer to Engin e
Owners Manual for specifications.
2.1.6. Clean exterior surfaces of cutting deck and
engine of any accumulation of spilled fuel, dirt,
grass, oil, etc. Keep engine air intake screen and
cooling fins clear at all times.
CONTROL
START
HANDLE
CONTROL –
SHOWN IN “FAST”
POSITION
FIGURE 2.3
2. Push primer bulb three times to start a cold
engine. NOTE: Primer should not be required to
restart a warm engine. See Figure 2.4
3. Pull blade control against handle.
4. Pull rope start handle to crank engine.
5. After engine starts, allow a brief warm-up until
engine runs smooth.
FIGURE 2.4
7
Section 2 - OPERATING INSTRUCTIONS
LOOSEN LOWER
LOWER
LOWEST CUTTING
HEIGHT
1
HIGHEST
6
1
5 6
LATCH
GROUND
FIRST/SLOW
WHEEL
SIXTH
2.2.2. PROPELLING MOWER
(Self Propelled Models Only)
1. Start engine. Refer to Section “Starting &
Operation”.
2. Move ground speed contr ol to the desir ed speed
position. See Figure 2.5.
3. Move wheel drive control against handle to
engage wheel drive and propel mower forward.
Forward speed can be adj usted while the m ower is
moving by changing position of the ground speed
control. See Figure 2.5.
DRIVE
CONTROL
FIRST
SPEED
CONTROL
SHOWN IN
FIGURE 2.5
2.3 STOPPING
Stop engine and blade by releasing the blade
control. Stop forward m otion of mower b y releasing
the wheel drive control.
2.4 HANDLE HEIGHT ADJUSTMENT
The height of the m ower hand le can be adj usted as
follows:
1. Loosen the lower nuts on each lower hand le as
shown in Figure 2.6.
HIGHER
2. Move u pper mower handle up or do wn until the
desired position is achie ved.
3. Tighten the lower nuts on each lower handle to
maintain desired positi on.
STOP engine and mower blade by releasing the
blade control before adjusting cutting height or
handle height.
2.5 CUTTING HEIGHT ADJUSTMENT
1. Pull the height adjusti ng lat c h out ward a nd move
to desired cutting height. See Figure 2.7.
2. Set all wheels at the same cuttin g height. The
highest cutting position is Notch 6. The lowest
cutting position is Notch 1. See Figure 2.8.
WARNING
LATCH
2
3
4
CUTTING
HEIGHT
FIGURE 2.7
HANDLE
NUTS ON EACH
LOWER HANDLE
FIGURE 2.6
LOWER
POSITIONS
CUTTING HEIGHT SETTINGS
FIGURE 2.8
8
Section 2 - OPERATING INSTRUCTIONS
SECURE ADAPTER
SECURE
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
2.6 RECYCLING OPERATION
(Optional accessory on some models)
NOTE: For best recycling res ults, cut up to a maximum
of 1/3 of grass blade length and recycle ONLY when
grass is dry.
1. Set all wheels in the highest cutting position
(Notch 6).
2. Move engine speed control to “FAST” (Rabbit)
position.
3. Move ground speed control to slowest speed
setting.
4. Proceed mowing slowly. If grass is ver y dense,
lower each rear wheel latch one notch lower than
the front wheel latches to improve recycling
performance.
2.7 INSTALLATION of GRASS CATCHER
(Optional accessory on some models)
STEP 1: Install the grass bag adapter and secure to
the side and top of the deck with the two nuts
provided on the machine. Slot in front edge of adapte r
must be und er nu t loc a ted on t op of dec k . Se e Fi gure
2.9.
WITH NUTS
ADAPTER
FIGURE 2.9
TO DECK WITH NUTS
STEP 2: Install grass catcher by sliding connector
over flange of adapter. Attach grass bag hooks over
middle handle cross b a r. See Figure 2 .1 0.
DO NOT operate without entire Grass Catcher or
guard in place. Grass Catcher components are
subject to deterioration during normal use. Inspect
frequently and replace worn or damaged
components immediately.
FIGURE 2.10
WARNING
9
Section 2 - OPERATING INSTRUCTIONS
REMOVE GRASS BAG
INSTALL
INSTALL
SLIDE
REMOVE RECYCLING
RECYCLING
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
2.8 INSTALLATION of DISCHARGE DEFLECTOR
(Optional accessory on some models)
1. Remove grass bag from handle and grass bag
adapter. See Figure 2.11.
2. Remove front and rear nuts attachi ng grass bag
adapter to deck. See Figure 2.11.
3. Install discharge deflector and secure to deck
using hardware removed in Step 2. Slot in front
edge of discharge deflector must be under nut as
shown and both bolts protruding through holes in
the side of the deflector. See Figure 2.12.
REMOVE NUTS
DISCHARGE
DEFLECTOR
FIGURE 2.11
FIGURE 2.12
FROM HANDLE AND
BAG ADAP TE R
DEFLECTOR SLOT
UNDER NUT
NUTS
WARNING
DO NOT operate without entire Grass Catcher or
guard in place. Grass Catcher components are
subject to deterioration during normal use. Inspect
frequently and replace worn or damaged
components immediately.
2.9 INSTALLATION of RECYCLING COVER
(Optional accessory on some models)
It will be necessary to remove bag adapter and
grass bag or discharge deflector before installing
recycling cover. See previous section for
instructions. Install the recycling cover and secure
to the side and top of the deck with the two nuts
provided on the m achine. Slide top portion of cover
under nut secured to the deck. See Figure 2.13.
COVER
COVER TO THE DECK
REMOVE THE TWO NUTS
FIGURE 2.13
10
Section 3 – MAINTENANCE
3.1 INTRODUCTION
To retain the quality of the mower, use genuine
SNAPPER replacem ent parts only. Contact a local
SNAPPER dealer for parts and service assistance.
For the correct part or information for a particular
mower, always mention model and serial number.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1. CHANGE ENGINE OIL
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for all
components to cool.
1. Refer to Engine Manual for proper oil
specifications and procedures.
2. For simplest/cleanest oil change, loosen lower
handle wing nuts and stand mower up on lower
handle as shown in Figure 3.1. Drain oil through
dipstick tube into a container.
FIGURE 3.1
IMPORTANT: Drain fuel tank before tipping
mower.
3.2.2. CHECK GREASE LEVEL IN TRANSMISSION
1. Remove transmission fill plug. Roll machine
forward or backward while looking down into plug
hole.
2. If liquid
(the small gear below the plug hole), add an
amount, to cover gear , of S napper “00” grease. See
Figure 3.2.
FILL PLUG
NOTE: Snapper “00” Grease (Part No . 2-9443) i s availa b le
at your SNAPPER dealer.
grease IS NOT visible on the input g ear
FIGURE 3.2
(Continued on Next Page)
11
Section 3 – MAINTENANCE
RECOMMENDED
3.2.2. CHECK GREASE LEVEL IN TRANSMISSION
(Continue d fr om pr e vious page )
NOTE: Do not spill grease or oil on surface of drive
disc. See Figure 3.3.
3. Reinstall transmission plug.
4. Check grease level after each 25 hours of
operation.
KEEP DRIVE DISC CLEAN !
3.2.4. CHECK ENGINE DRIVE BELT
1. Visually check engine drive belt for cracking,
fr aying, severed or be lt strands exposed. If wo rn or
damaged, replace belt before operating mower.
3.2.5. CHECK TRANSMISSION POLY-V BELT
1. Visually check poly-v belt for cracking, fraying,
severed or belt strands exposed. If worn or
damaged, replace belt before operating mower.
BLADE RETAINING
CAP SCREW
TORQUE VALUE
SHOULD BE
40 FT. LBS.
FIGURE 3.3
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool. Wear heavy leather gloves
when handling or working around cutting blades.
Blades are extremely sharp and can cause severe
injury.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil fr om crankcase will saturate the air
filter and cause the engi ne to be hard to start or not start
at all. If contaminatio n does oc c ur , the air filter will have to
be replaced.
3.2.3. CHECK MOWER BLADE
1. Disconnect spark plug wire and secure end
away from plug.
2. Tilt mower up on its rear wheels for access to
the blade cap screw. Do not tilt mower with spark
plug or carburetor down. See Figure 3.4.
3. Check torque of blade retaining cap screw.
Recommended torque should be 40 ft. lbs. See
Figure 3.4.
4. Check blade for sharpness, wear and damage.
Refer to Section “Blade Wear Limits”.
FIGURE 3.4
3.3 SERVICE - ANNUALLY
Perform all maintenance as described in the “Service
Schedule” section of thi s manual .
3.3.1. Engine
Service engine a c cording t o e ngin e owne r’ s manu al.
3.3.2. Air Filter
Refer to engine owner’s manual for service instructions.
3.3.3. Engine Oil
Refer to engine owner’s manual for service
instructions.
3.4 STORAGE PROCEDURE
Refer to the Engine Owner’s Manual for directions regarding
engine storage preparations. Prepare the mower for “end of
season” storage as follows:
1. Drain fuel from fuel tank and let engine run until all fuel is
out of the carburetor.
2. Dis connect and remove the spark plug w ire away
from spark plug before any other preparations are
made!
3. Tape all openin gs closed to pr event spra ying water into
exhaust or air intakes during washing.
4. Tilt mower up on its rear wheels and thoroughly clean the
underside of the d eck. Do not tilt m ower with spark plug or
carburetor down. Sc rape away an y accumulation of grass
with a putty knife and or wire brush.
5. Lubricate all expos ed metal with a lig ht coating of oil to
prevent cor rosion.
6. On self-propelled models disconnect transfer rod clip and
remove ground speed control rod be fore folding hand les.
7. Loosen handle knobs. Carefully fold the handles forward,
“flexing” the control cables to prevent cable damage.
8. Store the mower in a shed or oth er dry area, protec ted
from weather.
12
Section 4 - REPAIR & ADJUSTMENTS
BLADE
MAKE SURE THAT
CONE WASHER
WEAR LIMIT
DANGEROUS CONDITION !
WEAR LIMIT.
DANG
EROUS !
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns; allow sufficient time for
all components to cool. Wear heavy leather gloves
when handling or working around cutting blades.
Blades are extremely sharp and can cause severe
injury.
4.1 MOWER BLADE REPLACEMENT
4.1.1. STANDARD BLADE WEAR LIMIT
1. Inspect blade frequently for signs of excessive
wear or da ma ge . See Figure 4.1.
NEW BLADE
(NOTCH STARTS)
DO NOT USE ON MOWER !
REPLACE WITH NEW
BLADE.
WARNING
DO NOT use a cutting blade that shows signs of
excessive wear or damage. Refer to Section
“MOWER BLADE REPLACEMENT” for proper blade
inspection and service procedures.
4.1.2. BLADE SHARPENING
1. Disconnec t spark plug wire and sec ure end aw ay
from plug.
IMPORTANT: Drain fuel before tipping mower. DO
NOT tip machine with carb uretor or spark plug down. Oil
from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If
contamination does occur, the air filter will have to be
replaced.
2. Tilt mower up on its rear wheels. Do not tilt
mower with spark plug or carburetor down.
3. Remove blade. See Figure 4.3.
BLADE HUB IS
SEATED
BETWEEN
HUB
FLANGES
FIGURE 4.1
4.1.1.A. NINJA BLADE WEAR LIMIT
1. Inspect blade frequently for signs of excessive
wear or da ma ge . See Figure 4.2.
NEW BLADE
DO NOT USE A BLADE IN
THIS CONDITION !
CRACKS OR
NOTCHES
BEGIN TO
APPEAR ON TIP
FIGURE 4.2
2. Replace the blade if it is badly chipped, bent,
noticeably out of bal ance or has cracks or notch in
either tip. See Figure 4.1 & 4.2. Replace with new
blade.
FLANGE
BLADE
(Concave Side Up)
CAPSCREW
FIGURE 4.3
13
Section 4 - REPAIR & ADJUSTMENTS
CLUTCH CABLE
VINYL SPRING
1/16” TO 1/8”
UPPER
SPRING
LOWER
CLUTCH CABLE
CLUTCH CABLE EYE
DO NOT SHARPEN
END VIEW OF
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for all
components to cool.
4.1.2. BLADE SHARPENING
4. Shar p en b lad e on a gr ind in g whee l at an angle of
22 to 28 degrees. DO NO T sharpen blade beyond
original cutting edge. See Figure 4.4.
BEYOND ORIGINAL
CUTTING EDGE
22-28º
CLEARANCE
SPRING
EYE
SPRING HOOK
CABLE
BLADE TIP
BLADE ASSEMBLY
ORIGINAL CUTTING EDGE
FIGURE 4.4
5. Check blade for balance. If necessary, correct
balance by grinding heav y end of blade.
6. Reinstall blade. See Figur e 4.3. Check torque of
blade retaining cap screw. Recommended torque
should be 40 ft. lbs.
4.2 WHEEL DRIVE CONTROL ADJUSTMENT
1. The wheel drive control is properly adjusted
when there is 1/16” to 1/8” clearance between the
inside of the spring hook and the ins ide of the clutch
cable eye with the wheel driv e control r eleas ed. Se e
Figure 4.5.
SPRING
FIGURE 4.5
2. To adjust, unhook upper spring from cable eye
and rotate spring in direction required to extend or
shorten spring length.
3. Rehook upper spring to cable eye and check
clearance. Repeat procedure if required.
NOTE: The vinyl spring cover should be kept over the
spring at all times except for adjustments.
4. If the wheel drive contr ol fails to retu rn quickl y to
the “OFF” position when re leased, ch eck for binding
at the cable holdings locate d on the side of the right
handle. The upper c lip should be located 2” be low
the upper knob; the lower clip should be 4” above
the lower knob. The cable should slide freely with
the clips installed at these locations.
14
Section 4 - REPAIR & ADJUSTMENTS
USE
DRIVE
SPRING
DRIVEN DISC &
RUBBER RING
POLY
-
V
DRIVE
ENGINE
DRIVE
MOVE GROUND
SIXTH SPEED
SIXTH
FIRST
SPEED
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for all
components to cool.
4.3 DRIVEN AND DRIVE DISC SERVICE
If the mower does not propel itself properly, See
Figure 4.6. Check for the following problems:
BELT
SPRING
DRIVE
BELT
DISC
FIGURE 4.6
1. Grease on drive disc causing slippage.
2. Broken or disconnected drive spring.
3. Driven disc is out of adjustment.
4. Driven disc rubber is worn - does not contact
drive disc properly.
5. Worn Poly-V Belt or engine drive belt.
NOTE: If any of the above (1 thru 5) are causing
problems, service as follows:
4.3.1. Cleaning Drive Disc & Driven Disc.
If oil or grease on the drive disc or driven disc is
causing slippage, clean discs as follows:
1. Wipe away any oil or grease with a clean cloth.
2. Use either an approved grease solvent or hot,
soapy water to clean drive disc or driven disc.
3. Rinse components with clean water.
4. Dry components with a clean cloth.
4.3.2. Drive Spring Repair/Replacement
If drive spri ng is loose, rec onnect as sho wn in Figure
4.7. If spring is broken, replace with new spring.
IMPORTANT: If machine drive system continues
slipping see Trouble Shooting section.
4.3.3. DRIVEN DISC ADJUSTMENT
If the drive disc an d driven disc are clean and the
mower drive is sti ll s l ipp in g, adj us t the dr iv en d is c as
follows:
1. Place ground speed control in the number six
speed position. See Figure 4.8.
SPEED CONTROL TO
SIX-SPEED POSITION
NEEDLE
NOSE
PLIERS TO
INSTALL
DRIVE
SPRING
FIGURE 4.7
POSITION
FIRST
FIGURE 4.8
15
Section 4 - REPAIR & ADJUSTMENTS
1/8” MEASUREMENT TO
DRIVE
SLIDE DRIVEN
TRANSFER
ROD
CONNECTOR
HEX NUT
OUTSIDE
CONNECTOR
SPEED CONTROL
TRANSFER
DRIVEN DISC
DRIVE
DRIVEN DISC
TRANSFER
CONNECTOR
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
4.3.3. DRIVEN DISC ADJUSTMENT
(Continued From Previous Page)
2. Remove driven disc spring from driven disc
assembly. Loosen connector hex nut. See Figu re 4.9.
DISC ASSEMBLY
TOWARD OUTS IDE
EDGE
OUTSIDE EDGE OF DRIVE
DISC
DISC
SPRING
ROD
CONNECTOR
ASSEMBLY
DISC
HEX NUT
FIGURE 4.9
3. Slide driven disc assembly over to 1/8” from
outside edge of drive disc. Maintaining the 1/8”
measurement, remove any looseness from the
linkage. This can be done by holding the transfer rod
and applying pressure to the left (as viewed from
operators p osition). Th en retighten t he connect or hex
nut securely. See Figure 4.10. Move ground speed
control to the first speed position, then back to the
sixth speed position. Rech eck the 1/8” meas urement
described previously. Reins tall driven disc s pring to
driven disc assembly .
EDGE
CONNECTOR
FIGURE 4.10
4.3.4. Replacing Rubber Driven Disc
If the rubber is badly chunked or worn it must be
replaced. Install new Driven Disc as follows:
1. Using a small flat blade sc rewdriver, f ree the cli p
from the transfer r od. Then rem ove the transfer r od
from the clip and the speed contro l rod. See F igure
4.11.
CLIP
ROD
ROD
FIGURE 4.11
(Continued On Next Page)
16
Section 4 - REPAIR & ADJUSTMENTS
DRIVE DISC
ASSEMB
LY
INSTALL NEW
DRIVEN DISC
SNAP
RINGS
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
4.3.4. Replacing Rubber Driven Disc
(Continued from previous page)
2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3. Remove the two snap rings which secure the
rubber driven disc to the driven d is c as s em bl y. See
Figure 4.13.
4. Install new rubber driven disc onto driven disc
assembly with retaining rings.
5. Reverse above procedures for reassembly and
installation of driven disc assembly.
4.3.5. Replacing Bearing I n Driven D isc A ssembly
IMPORTANT: The bearing, on these “M” series
machines, is stak ed int o th e thr ust pl ate. The bearing will
have to be driven out with a m allet and a large p unch. A
new bearing with four retaining screws will have to be
purchased to replace existing bearing.
If the driven disc bearing requires replacement,
remove the driven disc assembly and replace
bearing as follows:
1. Using a small f lat blade sc rewdriver, f ree the cli p
from the transfer r od. Then rem ove the transf er rod
from the clip an d the spee d control ro d. See Figure
4.11.
2. Using needle nose pliers, unhook the drive
spring and slide the driven disc assembly off the
hex shaft. See Figure 4.12.
3. Remove both snap rings that secure rubber
driven disc hub to thrust plate. See Figure 4.13.
4. Slide the rubber driven disc hub out of the
bearing.
5. Drive out existing bearing.
6. Install new bearing and secure to thrust plate
with four retaining screws. Tighten screws securely.
7. Reassemble components in reverse order.
FIGURE 4.12
FIGURE 4.13
17
Section 4 - REPAIR & ADJUSTMENTS
3/8”
BALL BEARING
ENGINE DRIVE
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool.
4.3.6. Replacement Of Bearing On Pulley End Of
Hex Shaft
To replace the bear ing on t he pulle y end of the hex
shaft, proceed as follows:
1. Hold the hex shaft with an adjustable wrench
held next to the pulley.
2. Remove the 3/8” hex lock nut, which is located
on the outside of the right wheel bracket. See
Figure 4.14.
3. Remove holder, O-ring and bearing.
4. Install new bearing.
5. Carefully install new O-ring over the outside of the
new bearing.
6. Install bearing holder and secure with screws.
7. Install 3/8” hex lock nut.
BALL BEARING
“O” RING
LOCK NUT
HOLDER
FIGURE 4.14
4.4 BELT SERVICE
On self-propelled mowers, the engine belt transmits
power from engine to drive disc. The drive disc
powers the poly-v belt, which engages the
transmission that powers the rear wheels. Should
these belts b ecome worn , they coul d cause sl ippage,
which would impair mower performance. The
condition of the en gine belt and po ly-v belt shoul d be
checked after every 25 hours of mower operation.
4.4.1. Engine Drive Belt Replacement
(Stretch Type Belts)
1. Empty the fuel tank.
2. Note the belt routing in Figure 4.15. Th ere is no
idler pulley on these models to disconnect. See Figure
4.15.
PULLEY
TOP VIEW OF STRETCH TYPE BELT ROUTING
DRIVE BELT
DRIVE DISC
FIGURE 4.15
(Continued On Next Page)
18
Section 4 - REPAIR & ADJUSTMENTS
IDLER
DRIVE
DIFFERENTIAL
POLY
-
V
DRIVEN
INTERNAL TO OTH
SLOT IN END
DECK BRACKET
WARNING
DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for all
components to cool.
4.4.1. Engine Drive Belt Replacement
(Stretch Type Belts)
(Continued From Previous Page)
IMPORTANT: Drain fuel before tipping mower. DO
NOT tip machine with carb uretor or spark plug down. Oil
from crankcase will saturate the air filter and cause the
engine to be hard to start or not start at all. If
contamination does occur, the air filter will have to be
replaced.
3. Remove the driven disc. Refer to Section
“Replacing Rubber Dri ven Disc Ring” f or driven d isc
assembly removal procedure.
4. Tilt mower up on its rear wheels and remove
blade and blade hub. Assistance from another
person may be necessary to hold mower in the tilted
position.
5. Hold the slotted end of the drive disc bolt with a
screwdriver and remove the nut and internal tooth
lock washer. See Figure 4.16.
6. Remove the belt cover located under deck.
7. Lift the drive disc up and remove worn belt.
8. Loop one end of new belt over engine pulley and
insert the other end through slot in deck. See F igure
4.15.
PULLEY POSITIO N
9. Loop the belt around the pulley on the bottom of
the drive disc.
10. Reinstall drive disc and retaining hardware.
IMPORTANT: 1) The square shoulder of the drive
disc bolt must f it int o th e s q uar e h ol e of th e b us hin g.
2) The square end of bushing must fit into the
bracket slot.
11. Reinstall belt cover and tighten bolts sec urely.
12. Reinstall blade hub and cutter blade.
Recommended torque for blade cap screw is 40 ft. lb s.
4.4.2. Transmission Poly-V Belt Replacement
1. Remove the driven disc. Refer to Section on
“Replacing Driven Disc Rubber Ring” for procedure.
2. Note the r outing of the old belt around th e three
pulleys before removing it. See Figure 4.17.
3. Place ne w Poly-V Belt over end of hex shaf t and
onto driven pulley.
4. Work belt onto top of idler pulley.
5. Twist belt sidewa ys and pull it upward between
the differential bracket and drive pulley and then
down into the pulle y groove. Make sure the Poly-V
Belt is above belt guide. See Figure 4.17.
PULLEY
HEX SHAFT
PULLEY
BRACKET
BELT
OF DRIVE DISC
BOLT
(P ARTIALL Y SHOWN)
FIGURE 4.16
DRIVE DISC
BUSHING
BOLT RETAINER
LOCKWASHER
NUT
BELT GUIDE
PULLEY
ROUTING OF POLY-V BELT
FIGURE 4.17
19
TROUBLESHOOTING
Mower Will Not Move
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.
Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for
3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.
Engine Stalls or Stops
After Running
2. Fuel tank empty. 2. Fill with fuel to proper level.
3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.
4. Spark plug defective or gap set improperly. 4. Service spark plug.
5. Water, debris or stale fuel in fuel system. 5. Drain and clean fuel system.
Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty 1. Clean or replace filters.
2. Spark plug faulty. 2. Service spark plug.
3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.
Excessive Vibration 1. Damaged, out of balance or bent mower blade. 1. Service mower blade.
2. Loose blade components. 2. Service and tighten loose parts.
3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.
4. Lumpy or frayed belt 4. Replace belt.
Loss Of Traction
(Self-Propelled Models)
Cutting Grass
Improperly
Poor Grass Discharge
Oil Leaking
1. Blade control is released or is not being held securely
against handle.
1. Damaged transmission
2. Traction drive belt requires replacement 2. Replace traction drive belt.
3. Driven disc slipping 3. Clean or replace driven disc.
1. Cutting height too low or high. 1. Adjust cutting height.
2. Engine speed too slow. 2. Move engine speed control to “FAST” position.
3. Forward ground speed too fast. 3. Move ground speed control to a slower speed.
4. Terraced cut, side to side. 4. Adjust height of cut with height adjust levers.
5. Excessive deck pitch, front to rear. 5. Adjust height of cut with height adjust levers.
6. Cutting blade dull or damaged. 6. Sharpen cutting edges or replace blade.
1. Engine spe ed too slow. 1. Move engine speed control to “FAST” positi on.
2. Forward speed too fast. 2. Move ground speed control to a slower speed.
3. Grass is wet. 3. Mow when grass is dry.
4. Excessively worn or damaged blade. 4. Service mower blade.
5. Build up of grass clippings and debris under deck. 5. Clean deck.
6. Improper blade installed on deck.
7. Blade installed improperly on deck. 7. Install blade properly.
1. Leaking engine case.
Instructions.
1. Blade control should be held securely against
handle at all times during operation of mower.
1. Contact authorized SNAPPER dealer.
6. Install proper SNAPPER blade.
1. Contact authorized SNAPPER dealer.
2. Check and tighten drain plug.
3. Make sure dip stick or oil filler cap is securely
in place.
20
Parts Manual for 21” Steel Deck Walk Behind Mower
ITEM SERVICE PERFORMED
Engine Oil
Check Oil Level Page 6
SERVICE SCHEDULE
REF. EACH
USE 5 HRS
X
25
HRS
50
HRS
100
HRS
EACH
SEASON
Air Pre-Cleaner
Air Cleaner
Spark Plug
Engine Cooling
System
Drive Belts
Mower Blade
Mower Deck
Transmission
Grease
Drive Disc
*Change oil every 25 hours when operating under heavy load or high temperatures.
**Clean more often under dusty conditions or when air debris is present
4.5 MAINTENANCE/REPLACEMENT PARTS
Initial Oil Change Page 10
Periodic Oil Change Page 11
Clean Sponge Element Engine Manual
& Page 11.
Clean or Replace Engine Manual.
Replace Engine Manual.
Clean Shroud & Fins Engine Manual
Check For Wear And
Tension
Check For Wear, Damage
& Replacement
Clean Debris
Accumulation
Check Grease Level Pages 10-11
Periodic Grease Check Pages 10
Check for Wear Damage
& Replacement
Page 17-18
Page 11-12
Page 11
Page 14-18
X
X*
X**
X**
X
X**
X X X
X
X
X X
X
X
MAINTENANCE PARTS
Engine Speed Control (Briggs Engines) 2-9036
Blade Control Cable 7-2933
Clutch Pull Cable 7-2932
Cutter Blade (European Models Only) 1-9795
Cutter Blade (Mulching) 1-7168
Cutter Blade (Not Air Lift Compatible) 2-6691
Cutter Blade (Ninja - Quad Edge) 2-6407
Wheel Drive Pulley to Transmission Pulley Belt 1-2354
Engine to Drive Disc Belt 4-6784
Rubber Drive Tire 5-7787
Series 17
06136
21
DECAL IDENTIFICATION
SAFETY ALERT
READ, UNDERSTAND
AND FOLLOW INSTRUCTIONS AND WARNINGS IN OPERATOR’S
KEEP CHILDREN
SYMBOL. OBSERVE
AND FOLLOW ALL
SAFETY
INSTRUCTIONS.
(1) WARNING INSTRUCTIONS.
(2) WARNING: Do Not operate without entire Grass
Catcher or Guard in place.
(3) PRIME: Use for initial engine starting. Read and
follow engine operating and maintenance
instructions. Push bulb to prime engine.
(4) SPARK PLUG: Warns of potential electrical shock
from spark plug while engine is running.
(5) AIR FILTER: Indicates location of engine air filter.
To service the filter, read and follow the engine
operating and maintenance instructions.
MANUALS, AND ON THE MOWER, ENGINE AND ATTACHMENTS BEFORE OPE RATING.
AND OTHERS OUT
OF MOWING
(6) THROTTLE CONTROL: Indicates direction to
increase engine RPM (Hare), decrease engine RPM
(Tortoise), and direction to choke.
(7) SPEED SELECTOR: Shows direction of motion
and the ability to select one of six ground speeds by
rotating the lever.
22
DECAL IDENTIFICATION
(8) OPERATOR PRESENCE CONTROL (OPC):
Arrow points to the OPC bail. When bail is rotated
rearward, the engine may be start ed and will run as
indicated by the engine with rotating arrow. With
the engine running, the blade is rotating as
indicated by the cut grass s ymbol. When the bail is
released and rotates forward, the engine will stop.
(9) CLUTCH: Located on the plastic grip of the
traction control lever. Moving the lever toward the
handle engages the traction clutch and forward
motion starts. When the lever is rele ased, the clutch
disengages and forward motion stops.
(10) SHIFT WARNING: Located on the middle
handle. Indicates that the engine must be stopped
before shifting ground speed control.
(11) INJURY WARNING: Indicates possible severe
injury from rotating cutting blades.
(12) CE DECAL: Indicates European Certification.
(13) LWA-100: Indicates European noise level
certification.
EUROPEAN PERFORMANCE:
Maximum level of vibration measured at the
operators hand 19.1 m/sec2
23
3 YEAR LIMITED WARRANTY
For three (3) years fr om purchase date for the origi nal pur chas er 's r es ide ntial, non - c ommercial use, SNAPPER, through
any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found
upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days fr om purchase date for the original purchaser's commercial, rental, or other non-residenti al use,
SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon
examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for
replacement under this warranty must be paid by the purchaser.
This warranty does not apply to engi nes and the ir compone nts, and ba tteries, as t hese item s are warr anted separat ely.
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, im proper lubrication,
normal wear, or other cause beyond the contro l of SNAPPER. This warranty does not cover an y mac hine or component
part that has been altered or modified changing safety, performance, or durability.
Batteries have a on e (1) year pr orate d warra nty per iod with f ree replac em ent if r equire d durin g the f irst nin ety ( 90) da ys
from the original purchase date. SNAPPER will not be responsible for any installation cost incurred. The battery
warranty only covers original equipm ent batteries and does not cover dam age to the battery or machine caused by
neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper
electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY
Implied warranties, including those of me rchantability and fitness for a particular purpose, are limit ed to three
(3) years from purchase date for the original purchaser's resid ential or other non-commercial use, and ninety
(90) days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the
extent permitted by law, any and all impli ed warranties are excluded. This is th e exclusive remedy. Liabilities
for consequential damages, under any and all warranties are excluded.
Some states do not allo w limitations on how long an implied w arranty lasts, or do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: T HE USE OF REPLACEM ENT PARTS OTHER THAN GENUINE SN APPER PARTS M AY IMPAIR THE
SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER
ASSOCIATED WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:
Snapper ’s P r od uct Regis tr a t i on C en t er , P.O . B o x 1379 , M cDonou gh, Geor gia 30 25 3
24
Safety Instructions & Operator’s Manual for
TAIN VEHICLE COMPONENTS CONTAIN OR
EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER
AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS,
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR
EUROPEAN
21” STEEL DECK
WALK BEHIND MOWERS
SERIES 17
IMPORTANT
Snapper products are built using engines that meet or exceed all applicable emissions requirements on the
date manufactured. The labels on those engines contain very important emissions information and critical
safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine
manual, and on the machine, engine and attachments. If you have any questions about your Snapper
product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper,
McDonough, GA. 30253. Phone: (1-800-935-2967).
WARNING
BATTERY POSTS, TERMINALS
OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.
WARNING
ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CER
REPRODUCTIVE HARM.
COPYRIGHT © 2002
SNAPPER INC.
ALL RIGHTS RESERVED
MANUAL No. 7-4937 (I.R. 6/07/02)
Loading...