Snapper ER194515B User Manual

Safety Instructions & Operator’s Manual for
EUROPEAN
19” STEEL DECK
WALK MOWERS
SERIES 15
MODEL
MODEL NUMBER EXPLANATION
E R 19 45 15 B
MODEL DESIGNATION BRIGGS & STRATTON CUTTING WIDTH SERIES DESIGNATION ENGINE HORSE POWER
E – European Model 15 - Series Designation R – Recycling Model 45 – 4.5 HP (Engine Horse Power)
19 – 19” Cutting Width B – Briggs & Stratton Engine
Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense.
COPYRIGHT © 2000 SNAPPER INC. ALL RIGHTS RESERVED
MANUAL No. 7-3725 (I.R. 4/28/00)
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This powerf ul cutting machine is capab le of amputating hand s and feet and can throw objects that can cause injury and damage! Failure to comply with the follow ing SAFETY instru ctions could resu lt in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).
PROTECTION FOR CHILDREN
Tragic accidents can occur if the operator is not alert to the presence of children. Ch ildren are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
1. KEEP children out of the mowing area and under the watchful care of a responsible adult.
2. DO NO T allow children in yard wh en machine is operated and turn machine OFF if anyone enters the area.
3. DO NOT allow pre-teenage children to operate machine.
4. ALLOW only responsible adults & teenagers with mature judgment under close adult supervision to operate machine.
5. DO NOT pull mower backwards unless absolutely necessary. LOOK and SEE behind and down for children, pets and hazards before and while backing.
6. USE EXTRA CARE when approaching blind corners, shrubs, trees, or other object s that may obscure vision.
SLOPE OPERATION
1. Slopes are a major f actor related to slip and fall accidents, which can result in severe injury. All slopes require extra cau tion. If you feel uneasy on a slope, DO NOT mow it.
2. Mow across slopes, never up-and-down. Exercise extreme CAUTION when changing directions on slopes. DO NOT mow steep slopes or other areas where stability or traction is in doubt.
3. Use extra care with crass catchers or other attachments; these affect the handling and the stability of the machine.
PREPARATION
1. Read, understand, and follow instructions and warnings in this manual and on the mower, engine and attachments. Know the controls and the proper use of the mower before starting.
2. Only mature, responsible persons shall operate the machine and only after proper instruction.
PREPARATION
(Continued From Previous Column)
3. Data indicates th at operators age 60 and above, are involved in a large percentage of mower­related injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury.
4. Handle fuel wit h ext ra care. Fuels are flammabl e and vapors are explosive. Use only an approved fuel container. DO NOT remove fuel cap or add fuel with engine running. Add fuel outdoors only with engine stopped and cool. Clean spilled fuel and oil from machine. DO NOT smoke.
5. Check the area to be mowed and remove all objects such as toys, wire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere with mo win g. Also note the location of holes, stumps, and other possible hazards.
6. Keep people and pets out of the mowing area. Immediately, STOP Blade, Stop engine and Stop mower if anyone enters the area.
7. Check shields, deflectors, switches, blade controls and other safety dev ices frequently for proper operation and location.
8. Make sure all safety decals are clearly legible. Replace if damaged.
9. Protect yourself when mow ing and wear safety glasses, long pants and substantial footwear. DO NOT mow barefooted or with sandals.
10. Know how to STOP blade and engine quickly in preparation for emergencies.
11. Use extra care when loading or unloading the machine into a trailer or truck.
12. Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or torn spots.
2
IMPORTANT SAFETY INSTRUCTIONS
OPERATION
1. DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area wh ile engine is running.
2. STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.
3. Mow only in daylight or good artificial light.
4. DO NOT operate mower while under the influence of alcohol or drugs.
5. After striking a foreign object or if mower vibrates abnormally, STOP the engine, disconnect and secu re spark plug wire. Inspect the mower for any damage and repair the damage.
6. DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or balance.
7. STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.
8. DO NOT mow on wet grass. Always be sure of your footing. Keep a firm hold on the handle and walk, never run. Slipping could cause injury.
9. DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE before leaving the operators position for any reason.
10. Before cleaning, repairing or inspecting make certain engine, blade and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.
11. STOP engine and w ait until the blade comes to complete STOP before removing grass bag and/or clearing grass.
12. DO NOT operate mower without the entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.
13. Slow down before turning.
14. Watch out for traffic when near or crossing roadways.
15. DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.
MAINTENANCE AND STORAGE
1. DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.
2. Keep mo wer and engine f ree of grass, leaves or excess grease to reduce fire hazard and engine overheating.
3. When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.
4. Keep all bolts, especially blade bolts, nuts and screws properly tight. Check that all cott er pins are in proper position.
5. Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, a deadly poison.
6. Service engine and make adjustments only when engine is stopped. Removed spark plug wire from spark p lu g an d secu re w ire away from spark plug to prevent accidental starting.
7. DO NOT change engine governor speed settings or overspeed engine.
8. Check grass bag assembly frequently for wear or deterioration to avoid thrown objects and exposure to moving parts. Replace with new bag if loose seams or tears are ev ident. Rep lace slider or bag adapter if broken or cracked.
9. Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.
10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.
11. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.
12. Use only genuine SNAPPER replacement parts to assure that original standards are maintained.
3
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS................................................2-3
TABLE OF CONTENTS............................................................................ 4
SECTION 1 - FAMILIARIZATION..............................................................5
SECTION 2 - OPERATING INSTRUCTIONS.........................................6-9
Pre-start Checklist...................................................................................................... 6
Starting & Stopping Engine & Blades...................................................................6-7
Handle Height Adjustment.........................................................................................7
Cutting Height Adjustment........................................................................................ 8
Recycling Operation................................................................................................... 8
Recycling Cover Installation/Removal ..................................................................... 8
Discharge Deflector Installation ............................................................................... 9
SECTION 3 - MAINTENANCE INSTRUCTIONS................................10-11
Change Engine Oil.................................................................................................... 10
Check Mower Blade ................................................................................................. 10
Service - Annually.....................................................................................................11
Engine................................................................................................................... 11
Air Filter................................................................................................................11
Engine Oil............................................................................................................. 11
Storage Procedure ................................................................................................... 11
SECTION 4 - ADJUSTMENTS AND REPAIR......................................... 12
Mower Blade Replacement...................................................................................... 12
Mower Blade Sharpening ........................................................................................ 12
TROUBLESHOOTING ............................................................................ 13
SERVICE SCHEDULE ............................................................................ 14
Maintenance/Replacement Parts ............................................................................ 14
DECAL IDENTIFICATION..................................................................15-16
WARRANTY............................................................................................17
PRIMARY MANTENANCE.................................................................18-21
4
Section 1 - FAMILIARIZATION
CAP
CONTROL
BLADE
RECOIL ROPE GUIDE
ROPE START HANDLE
FUEL FILLER
PRIMER BULB
KNOB
KNOB
OIL FILL CAP & DIPSTICK
AIR CLEANER
RECYCLING COVER
PRIMER SEE INSET
1.1 INTRODUCTION
This manual has been prepared for the operator s of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices. Read, Understand and Follow the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3 of this manual and all safety messages on the mower and attachments before operating the mower.
FIGURE 1.1
1.2 NOMENCLATURE
MUFFLER
CUTTING DECK
CUTTING HEIGHT ADJUSTMENT BUSHINGS
The nomenclature information above, Figure 1.1, shows the essential parts of the SNAPPER WALK BEHIND MOWERS. It is recommended that all operators of the mower becom e thoroughly familiar with the controls, parts and operation of the mower before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference.
5
Section 2 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
Make the following checks and perform the service required before each start-up.
2.1.1. Check guards, deflectors, grass bag, adapter and covers to mak e sure all are in place and securely tightened.
2.1.2. Check blade contr ol to insure it works freely. See Figure 2.1.
BLADE CONTROL
2.1.5. Add fuel to tank after pushing the mower
outside where fumes can safely dissipate. Make sure cap is tightened after refueling. Refer to Engine Owners Manual for fuel specifications.
2.1.6. Clean exterior surfaces of cutting deck and engine of any accumulation of spilled fuel, dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times.
2.2 STARTING & OPERATION
2.2.1. ENGINE & BLADE
The engine speed is pre-set for optimum mowing performance and is not adjustable. An engine primer is provided to assist when starting a cold engine. The primer should not be required when restarting a hot engine.
1. Push primer bulb three times to start a cold engine. NOTE: Prim er s hould not be required when restarting a hot engine. See Figure 2.3.
IMPORTANT: Stop the engine (and blade) by releasing
the blade control.
FIGURE 2.1
2.1.3. Check cutting height. Adjust to desired height.
2.1.4. Check engine oil and add oil as needed to bring
level up to the full mark. Refer to Engine Owner’s Manual for oil specifications. See Figure 2.2.
CHECK ENGINE OIL
FIGURE 2.2
PUSH PRIMER BULB THREE TIMES
FIGURE 2.3
2. Pull blade control against handle.
3. Pull rope start handle to crank engine.
4. After engine starts, allow a brief warm-up until
engine runs smooth.
6
Section 2 - OPERATING INSTRUCTIONS
2.3 STOPPING
Stop engine and blade by releasing the blade control. See Figure 2.4.
RELEASE BLADE CONTROL TO STOP ENGINE & BLADE
BLADE CONTROL
2.4 HANDLE HEIGHT ADJUSTMENT
The height of the mower handle can be adjusted as follows:
1. Loosen the two nuts on the inside of each of the lower handles as shown in Figure 2.5.
2. Move the handle up or down to the desired height.
3. Retighten all nuts securely after adjustment.
LOOSEN NUTS TO ADJUST HANDLE HEIGHT
FIGURE 2.4
WARNING
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.
FIGURE 2.5
7
Section 2 - OPERATING INSTRUCTIONS
WARNING
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.
2.5 CUTTING HEIGHT ADJUSTMENT
1. FRONT WHEELS: Reposition the front axle by
raising the front wheels off the gr ound, then pull in the spring loaded bushings until they clear the brackets. Move bushings to the desired height of cut position and release the bushings. See Figure
2.6.
2. REAR WHEELS: Reposition the rear axle by raising the rear wheels off the ground, then pull in the spring loaded bushings until they clear the brackets. Move bushings to the desired height of cut position and releas e the bushings. Position the rear bushings in to the same notches corresponding with notches for the front wheels to maintain the level of the deck. See Figure 2.6.
NOTE: T here are four c utting height adjustment notc hes on each wheel. The top notch is the lowest cutting height and the lowest notch is the highest.
DECK BRACKET
SPRING LOADED BUSHING
FIGURE 2.6
2.6 RECYCLING OPERATION NOTE: For best recycling results, cut up to a m aximum
of 1/3 of grass blade length and recycle ONLY when grass is dry.
1. Set all wheels in the highest cutting position (Notch 4).
2. Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.
2.7 RECYCLING COVER (REMOVAL/INSTALLATION)
1. REMOVAL: The recycling cover is secured in
place with two knobs. To remove the cover, unscrew the two knobs and lift off the cover. See Figure 2.7.
2. INSTALLATION: When reinstalling the cover, the deck sidewall should fit between the tab and outside of cover. Tighten knobs securely. See Figure 2.8.
KNOBS SECURE COVER
TAB FITS BEHIND DECK EDGE
RECYCLING COVER
FIGURE 2.7
FIGURE 2.8
TAB
MAKE CERTAIN TAB FITS TO INSIDE OF DECK
8
Section 2 - OPERATING INSTRUCTIONS
WARNING
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.
WARNING
DO NOT operate mower without entire Grass Catcher, Discharge Deflector or Recycling Cover in place.
2.8 DISCHARGE DEFLECTOR (INSTALLATION)
1. Remove the recycling cover. Loosen and
remove the two knobs securing the cover to the deck and rem ove the c over fr om the two bolts. The two bolts remain in the deck. See Figure 2.9.
2. Rem ove nut and bolt located below the front of the discharge opening. See Figure 2.9.
TWO BOL TS REMAIN IN DECK
REMOVE THIS NUT & BOLT
FIGURE 2.9
3. Place discharge deflector over two bolts at top
of discharge opening and secure to deck using the two knobs removed in Step 1. Tighten knobs securely.
4. Using hardware removed in Step 2, insert bolt with head on inside of deck into bottom rear hole of discharge deflector. Secure to deck with nut. See Figure 2.10.
FIGURE 2.10
9
Section 3 - MAINTENANCE
3.1 INTRODUCTION
To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and ser vice assistance. For the correct part or information for a particular mower, always mention model and serial number.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1. CHANGE ENGINE OIL
WARNING
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil f rom crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occ ur, the air f ilter will have to be replaced.
1. Disconnect spark plug wire and secure end away from plug. The item s needed to perform oil change are: cloth rags, (1) 3/8” drive ratchet with a short extension and (1) shallow pan.
2. Tilt mower up on its rear wheels for access to the oil drain plug located underneath the mower deck. Do not tilt mower with spark plug or carburetor down. See Figure 3.1.
4. Loosen with ratchet and short extension, but do not remove oil drain plug. Loosen plug until you can turn it with your fingers.
5. Lower the mower down and place the piece of wood under left rear wheel. Reach under mower and remove drain plug and allow oil to drain out completely in pan. Some oil may spill onto hands, immediately wipe hands clean with cloth rags.
6. Tilt mower back up and replace drain plug. Tighten securely but do not over tighten.
7. Fill engine with oil as specified in Engine Owner’s Manual.
8. Check air cleaner and perform air filter maintenance as specified in the Engine Owner’s Manual.
IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil f rom crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occ ur, the air f ilter will have to be replaced.
3.2.2. CHECK MOWER BLADE
1. Disconnect spark plug wire and secure end away
from plug.
2. Tilt mower up on its rear wheels for access to the blade cap screw. Do not tilt mower with spark plug or carburetor down. See Figure 3.2.
3. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs. See Figure 3.2.
4. Check blade for sharpness, wear and damage. Refer to Section “Blade Wear Limits”.
BLADE RETAINING SCREW
DRAIN PLUG
FIGURE 3.1
3. Place shallow pan underneath the approximate
center of the oil drain plug.
To avoid spilling fuel, empty engine gas tank before tilting mower.
10
CHECK TORQUE OF BLADE RETAINING SCREW.TORQUE TO 30 TO 40 FT. LBS.
FIGURE 3.2
WARNING
Section 3 - MAINTENANCE
3.3 SERVICE - ANNUALLY
Perform all maintenance as described in the “Service Schedule” section of this manual.
3.3.1. Engine
Service engine according to engine owner’s manual.
3.3.2. Air Filter Refer to engine owner’s manual for service instructions.
3.3.3. Engine Oil Refer to engine owner’s manual for service instructions.
3.4 STORAGE PROCEDURE
Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:
1. Drain fuel f rom fuel tank and let engine r un until all fuel is out of the carburetor.
2. Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!
3. Tape all openings closed to prevent spraying
water into exhaust or air intakes during washing.
4. Tilt mower up on its rear wheels and thoroughly clean the underside of the deck . Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and or wire brush.
5. Lubricate all exposed metal with a light coating of oil to prevent corrosion.
6. Loosen handle k nobs. Carefully fold the handles forward, “flexing” the c ontro l cables to pr event cable damage.
7. Store the mower in a shed or other dry area, protected from weather.
11
Section 4 - ADJUSTMENTS & REPAIR
WARNING
DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.
4.1 MOWER BLADE REPLACEMENT
4.1.1. STANDARD BLADE WEAR LIMIT
1. Inspect blade frequently for signs of excessive
wear or damage. See Figure 4.1.
2. Tilt mower up on its rear wheels.
3. Remove blade. See Figure 4.2.
BLADE
NEW BLADE
WEAR LIMIT (NOTCH STARTS)
DANGEROUS CONDITION ! DO NOT USE ON MOWER ! REPLACE WITH NEW
FIGURE 4.1
WARNING
DO NOT use a cutting blade that shows signs of excessive wear or damage. Refer to Section “MOWER BLADE REPLACEMENT” for proper blade inspection and service procedures.
4.1.2. BLADE SHARPENING
1. Disconnect spark plug wire and secure end away
from plug.
IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occ ur, the air f ilter will have to be replaced.
REMOVE BLADE RETAINING SCREW
FIGURE 4.2
4. Sharpen blade on a grinding wheel at an angle of 22
to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.3.
NOTE: DO NOT SHARPEN BEYOND ORIGINAL CUTTING EDGE.
22-28º
ORIGINAL CUTTING EDGE
BLADE TIP
END VIEW OF BLADE
FIGURE 4.3
5. Check blade for balance. If necessary, correct
balance by grinding heavy end of blade.
6. Reinst all blade. See Figure 3.2. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs.
12
TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Engine Will Not Start
Using Recoil Starter
Engine Stalls or Stops
After Running
Engine Loses Power
Excessive Vibration
Cutting Grass
Improperly
Poor Grass Discharge
Oil Leaking
1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.
2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for
instruction.
3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.
4. Spark plug faulty. 4. Replace with new spark plug.
1. Blade control is released or is not being held
securely against handle.
1. Blade control should be held securely against
handle at all times during operation of mower.
2. Fuel tank empty. 2. Fill with fuel to proper level.
3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.
4. Spark plug defective or gap set improperly. 4. Service spark plug.
5. Water, debris or stale fuel in fuel system. 5. Drain and clean fuel system.
1. Engine air pre-cleaner or air cleaner dirty 1. Clean or replace filters.
2. Spark plug faulty. 2. Service spark plug.
3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.
1. Damaged, out of balance or bent mower blade. 1. Service mower blade.
2. Loose blade components. 2. Service and tighten loose parts.
3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.
1. Cutting height too low or high. 1. Adjust cutting height.
2. Engine speed too slow. 2. Contact authorized SNAPPER Dealer.
3. Forward ground speed too fast. 3. Walk at slower pace.
4. Terraced cut, side to side. 4. Adjust height of cut with height adjust bushings.
5. Excessive deck pitch, front to rear. 5. Adjust height of cut with height adjust bushings.
6. Cutting blade dull or damaged. 6. Sharpen cutting edges or replace blade.
1. Engine speed too slow. 1. Contact authorized SNAPPER Dealer.
2. Grass is wet. 2. Mow when grass is dry.
3. Excessively worn or damaged blade. 3. Service mower blade.
4. Build up of grass clippings and debris under deck. 4. Clean deck.
5. Improper blade installed on deck. 5. Install proper SNAPPER blade.
6. Blade installed improperly on deck. 6. Install blade properly.
1. Leaking engine case. 1. Contact authorized SNAPPER dealer.
2. Check and tighten drain plug.
3. Make sure dipstick or oil filler cap is securely in
place.
13
ITEM SERVICE PERFORMED
Engine Oil
Check Oil Level Page 6
SERVICE SCHEDULE
REF. EACH
USE 5 HRS
X
25
HRS
50
HRS
100
HRS
EACH
SEASON
Air Cleaner
Spark Plug
Mower Blade
Mower Deck
* Change oil every 25 hours when operating under heavy load or high temperatures. **Clean more often under dusty conditions or when air debris is present
4.2 MAINTENANCE/REPLACEMENT PARTS
Initial Oil Change Page 10 Periodic Oil Change Page 11
Clean or Replace Engine Manual. Replace Engine Manual. Check For Wear, Damage
& Replacement Clean Debris Accumulation
Page 10 & 12 Page 11
X X*
X**
X X
X
MAINTENANCE PARTS
Blade Control Cable 7-2933 Cutter Blade (Mulching) 1-7167 Parts Manual for 19” Steel Deck Walk Behind Mower Series 14 & 15 06066
14
OF MOWING
SAFETY ALERT
SYMBOL. OBSERVE
AND FOLLOW ALL
SAFETY
INSTRUCTIONS.
READ, UNDERSTAND A ND FOLLOW INSTRUCTIONS AND WARNINGS IN OPERATOR’S MANUALS, A ND ON THE MOWER, ENGINE AND ATTA CHMENTS BEFORE OPERATING.
(1) WARNING INSTRUCTIONS.
DECAL IDENTIFICATION
KEEP CHILDREN AND OTHERS OUT
WARNING (DECK)
DECAL
P/N 7-2921
(2) WARNING (DECK): Read and follow Starting and Safety Instructions in Owner’s Manual. Improper use of machine can result in serious injury.
(3) WARNING: Do Not operate without entire Grass Catcher or Guard in place.
WARNING DECAL
22841
(4) WARNING: Located on the right side of the Mower Deck. It advises operator of the danger of the rotating blade.
15
DECAL IDENTIFICATION
29776
SPARK PLUG
SYMBOL
P/N 29779
(5) SPARK PLUG: Warns of potential electrical shock from plug while engine is running.
EUROPEAN NOISE
CONTROL DECAL
23009
(6) NOISE CONTROL: This unit is certified to be within the 100 dBA sound power limit at the specified Engine RPM.
EUROPEAN
COMMUNITY
DECAL
(7) EUROPEAN PERFORMANCE: Maximum level of vibration measured at the operators hand is 23.4 m/sec2.
(8) OPERATOR PRESENCE CONTROL (OPC): Arrow points to the OPC bail. When bail is rotated rearward, the engine
may be started and will r un as indicated by the engine with rotating arrow. W ith the engine running, the blade is rotating as indicated by the cut grass symbol. When the bail is released and rotates forward, the engine will stop.
16
3 YEAR LIMITED WARRANTY
For three (3) years from pur chase date f or the original pur chaser 's res idential, non-com m erc ial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applic able), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
For ninety (90) days from purchase date for the or iginal purchaser's commercial, rental, or other non-residential use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replacement under this warranty must be paid by the purchaser.
This warranty does not apply to engines and their components , and batteries, as these item s are warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any machine or com ponent part that has been altered or modified changing safety, performance, or durability.
Batteries have a one (1) year prorated warranty period with free replacement if requir ed during the first ninety (90) days from the original purchas e date. SNAPPER will not be responsible for any installation cost incurred. T he battery warranty only covers original equipment batteries and does not cover dam age to the battery or machine caused by neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.
There is no other express warranty.
DISCLAIMER OF WARRANTY Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to three (3) years from purchase date for the original purchaser's residential or other non-commercial use, and ninety (90) days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages, under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WARNING: THE USE OF REPL ACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF SUCH PARTS.
IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:
Snapper’s Product Registration Ce nter, P.O. Box 1379, McDonough, Georgia 30253
17
PRIMARY MAINTENANCE
18
PRIMARY MAINTENANCE
19
PRIMARY MAINTENANCE
20
PRIMARY MAINTENANCE
21
SERVICE NOTES
______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________
22
Safety Instructions & Operator’s Manual for
EUROPEAN 19” STEEL DECK WALK BEHIND MOWERS SERIES 15
IMPORTANT
Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand , and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).
WARNING
BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD A ND LEAD COMPOUNDS, CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CA USE CA NCER A ND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HA NDS A FTER HA NDLING.
WARNING
ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN V EHICLE COMPONENTS CONTAIN OR EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CA USE CA NCER OR OTHER REPRODUCTIVE HA RM.
COPYRIGHT © 2000 SNAPPER INC. ALL RIGHTS RESERVED
MANUAL No. 7-3725 (I.R. 428./00)
23
Loading...