Parts Manual fo
r
R
3
21" CAST DECK WALK BEHIND MOWE
EUROPEAN SERIES
MODEL
ELP216753BDV (7800140)
ELP21703BV (7800047)
ELP21703BV (7800121)
ELP21703BV (80662)
ELP21703BDV (7800255)
Briggs & Stratton Yard Power Products Group
535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967
Revision C,
Manual No. 7006204
TP 400-5062-C-WB-N8/12/2008
s
PAGE GROUP
4
8
10
12
14
16
HANDLES & CONTROLS
ENGINE, CUTTING DECK, BLADE
WHEELS, FRONT & REAR
TRANSMISSION
DECALS
ACCESSORIES
Table Of Content
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
Manual No. 7006204
3
TP 400-5062-C-WB-N
HANDLES & CONTROLS
Manual No. 7006204
TP 400-5062-C-WB-N
21" CAST DECK WALK BEHIND MOWER
4
EUROPEAN SERIES 3
HANDLES & CONTROLS
p
y
Part No Descri
1 7074411 1 HANDLE, Upper
2 7074156 1 HANDLE, Middle
3 7034864 2 BRACKET, Handle
4 7073821 1 COTTER PIN, Bow Tie Locking
5 7074418 1 BAIL, OPC Control
6 7034872 1 CLIP, Zone Control
7 7034608 1 * CABLE, Zone Control (53.98”)
7 7100976 1 * CABLE, Zone Control (OPC) DOV Engine (53.73”) used on Model ELP216753BDV
8 7046520 1 WELDMENT, Handle Clutch
9 7028407 1 GRIP, International Symbol
10 7046518 1 CABLE, Clutch (Adjustable)
11 7026219 5 CLAMP, 7/8” Double Cable
12 7012080 1 CABLE-TIE, 7” not shown
13 7073064 1 BRACKET, Shift
14 7024641 4 WIRE TIE, 1.29” Long Black
15 7091075 2 SCREW, #10-24 x 5/8” Slotted Hex Washer Head Self-Tap
16 7090188 8 WASHER, 11/32” Flat
17 7091552 2 WASHER, 7/32” Flat
18 7074140 1 CONTROL PANEL (w/o El. Switch Hole)
19 7091200 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
20 7028488 1 ROPE GUIDE (1/4-20 threads)
21 7076978 1 NUT, 1/4-20 Hex Nyloc
22 7074460 1 * THROTTLE CONTROL, 7.0 HP B&S (48.5”)
22 7100999 1 * THROTTLE CONTROL, 6.75 HP B&S DOV (48.0”) used on Model ELP216753BDV
23 7075308 2 THROTTLE KNOB
24 7091190 4 BOLT, 5/16-18 x 1-1/2” Curved Head Carriage
25 7023810 1 FOAM GRIP, 18.75”
26 7091088 2 SCREW, 3/8-16 x 2” Hex Head Self-Tap
27 7091585 2 NUT, 3/8-16 Hex Center Lock
28 7090391 6 WASHER, 5/16” Internal Tooth Lock
29 7029369 1 * CONTROL, Speed Select
30 7091189 2 SCREW, 5/16-18 x 2” Square Neck Curved Head
31 7091298 8 NUT, 5/16-18 Hex Nyloc
32 7079577 3 SCREW, 1/4-20 x 1-1/2” Hex Head Cap GR 5
33 7090053 5 WASHER, 1/4” Internal Tooth Lock or 7091023
34 7091576 5 NUT, 1/4-20 Hex or 7091100
35 7090505 2 SCREW, 1/4-20 x 2” Hex Head Cap GR 5
tionItem Qt
Note
Footnotes:
NOTE: * Snapper part number is stamped on cable.
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
5
TP 400-5062-C-WB-N
HANDLES & CONTROLS
Manual No. 7006204
TP 400-5062-C-WB-N
21" CAST DECK WALK BEHIND MOWER
6
EUROPEAN SERIES 3
HANDLES & CONTROLS
p
y
Part No Descri
36 7014343 2 BUSHING, .27 x .35 x .4 Flange
37 7023792 1 PIN, 1/4 x 1-1/2”
38 7091020 1 PUSHNUT, 1/4”
39 7026436 1 CLAMP, Double Tube
40 7035744 2 KNOB, 5/16-18 Wing (Black)
tionItem Qt
Note
Footnotes:
NOTE: * Snapper part number is stamped on cable.
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
7
TP 400-5062-C-WB-N
ENGINE, CUTTING DECK, BLADE
Manual No. 7006204
TP 400-5062-C-WB-N
21" CAST DECK WALK BEHIND MOWER
8
EUROPEAN SERIES 3
ENGINE, CUTTING DECK, BLADE
p
y
Part No Descri
1 7061962 1 DECK, 21” Cast Aluminum Rocker (Red) was 7073626
2 7074124 1 BELT COVER, Commercial Metal B&S
3 7091201 1 SCREW, #10-24 x 1-1/2” Slotted Hex Washer Head Self-Tap
4 -- 1 * ENGINE, 6.75 H.P. Briggs Dov, Euro, Mod. 100602-0122-B1
4 -- 1 * ENGINE, 7.0 H.P. Briggs Intek, Euro, Mod. 128602-0112-E1
4 -- 1 * ENGINE, 7.0 H.P. Briggs Dov, Euro OHV, Mod. 100602-0139-
B1
5 7023153 1 CLAMP, Casing
6 7023154 1 SCREW, #10-32 x 5/8” Self-Tap
7 7073293 1 PLUG, Hole (Polyethylene)
8 7091714 4 BOLT, 5/16-18 x 1” Round Head Carriage GR 5 or 7091238
9 7052881 1 ASSEMBLY, Discharge Door
10 7091819 8 SCREW, 1/4-20 x 5/8” Hex Washer Face Self-Tap or 7090362
11 7091294 2 WASHER, .28 x .63 x .06 Flat was 7090055
12 7033752 1 PLATE, Height Adjust
13 7091191 2 RIVET, 3/16 x 1/2” Steel
14 7043835 1 BRACKET, RH Trailing Shield Pivot Rod
15 7043836 1 BRACKET, LH Trailing Shield Pivot Rod not shown
16 7033732 2 SUPPORT, Rear Axle
17 7091892 1 PUSHNUT, 1/4” Black
18 7043808 1 ROD, Trailing Shield Pivot (1/4” Dia. x 16-1/4” long)
19 7043870 1 SHIELD, Trailing, Commercial Cast
20 7024595 1 BAFFLE, Discharge
21 7091075 5 SCREW, #10-24 x 5/8” Slotted Hex Washer Head Self-Tap
22 7091088 2 SCREW, 3/8-16 x 2” Hex Head Self-Tap
23 7016719 2 IDLER SPACER
24 7090613 2 NUT, 3/8-16 Hex Flange Lock or 7091619
25 7072143 1 BELT GUIDE (Wireform)
26 7015780 1 PULLEY, Traction Drive (25mm x 2-1/8” O.D.)
27 7092086 1 SET SCREW, 5/16-18 x 1/2” Hex Recess
28 7091214 1 KEY, Hi-Pro #HP506 (Briggs engine)
29 7076979 2 NUT, 3/8-16 Hex Nyloc
30 7026631 1 HUB, Blade Drive, 25mm Internal Dia. (with integral key)
31 7026428 1 BLADE, 21” Bagging
32 7079268 1 WASHER, 3/8” Split Lock (Heavy)
33 7090483 1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap GR 5
34 7091304 2 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
tionItem Qt
Note
Footnotes:
NOTE: * Purchase engine components directly from engine manufacturer dealer.
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
9
TP 400-5062-C-WB-N
WHEELS, FRONT & REAR
Manual No. 7006204
TP 400-5062-C-WB-N
10
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
WHEELS, FRONT & REAR
p
y
Part No Descri
1 7074629 2 REAR WHEEL ASSY, 9 x 2 (“Mass” Tread) includes Bushing 7073618; use
2 7100184 2 REAR WHEEL ASSY, 9 x 2 (LS Tread) includes Bushing 7073618; use
3 7101104 2 REAR WHEEL ASSY, 9 x 2 (Double Bar II Tread) includes Bushing 7024541; use
4 7073618 2 BUSHING, Wheel (powdered metal)
5 7024541 2 BUSHING, Wheel (nylon)
6 7028456 2 FRONT WHEEL ASSY, 8 x 2 (“Mass” Tread) use with Hub 7016152
7 7100015 2 FRONT WHEEL ASSY, 8 x 2, (LS Tread)
8 7101105 2 FRONT WHEEL ASSY, 8 x 2, (Double Bar II Tread)
9 7100114 2 HUB CAP, 3-1/4” Diameter, Black
10 7091193 4 HAIRPIN, 1/16 x 29/32” Cotter
11 7091192 4 WASHER, 1/2” Flat
12 7024540 2 HUB CAP, 9” Euro
13 7029492 1 BELT, Traction Drive, Sect. 3L, 33.20” effective length engine/transmission
14 7013946 2 WHEEL RETAINER, 3/8”
15 7091232 1 PIN, 3/8 x 5/8”
16 7046522 1 SPRING, Clutch (Also shown on Transmission
17 7041364 1 WELDMENT, Tie Bar
18 7091598 1 COTTER PIN, 1/8 x 3/4” was 7090365
19 7024751 1 SPRING, Tie Bar
20 7016152 2 HUB CAP, Front Wheels
21 7024558 2 BUSHING, Front Axle
22 7041344 1 WELDMENT, Front Axle
23 7034341 1 SPRING, Axle Retaining RH
24 7034340 1 SPRING, Axle Retaining LH
25 7100088 2 HUB CAP, 1-3/8: Diameter black
tionItem Qt
Note
with Hub 7024540
with Hub 7100114
with Hub 7100114
Page)
Footnotes:
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
11
TP 400-5062-C-WB-N
TRANSMISSION
Manual No. 7006204
TP 400-5062-C-WB-N
12
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
TRANSMISSION
p
y
Part No Descri
1 AXLE/TRANSMISSION ASSEMBLY (Ref. only, not a parts sale
item)
1 7026479 2 SEAL, Pinion (Felt)
2 7026478 2 RETAINER, Pinion Seal
3 7091084 4 SCREW, 1/4-20 x 3/8” Hex Washer Head, Self-Tap
4 7014341 4 RING, External Retaining Waldes # 5133-50
5 7025066 2 ASSEMBLY, Bearing Carrier includes bearing p/n 7024724
6 7024715 2 BUSHING, Rear Axle (S/P)
7 7024748 1 TUBING, 5/8 I.D. Convoluted
8 7091941 1 SCREW, #10-24 x 3/4” Pan Head Machine
9 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Head, Self-Tap
10 7035325 1 BRACKET, Transmission
11 7046522 1 SPRING, Clutch
12 7091552 1 WASHER, 7/32” Flat
13 7091267 2 * NUT, #10-24 Hex Center Lock
14 7024749 2 PAWL, 3/16” O.D.
15 7028813 1 TRANSMISSION ASSY, 3SP Commercial
16 7035540 1 * LEVER, Transmission (Metal)
17 7091075 1 * SCREW, #10-24 x 5/8” Slotted Hex Washer Head Self-Tap
18 7091187 1 NUT, M10 x 1.50 Hex Nyloc
19 7029494 1 PULLEY, Transmission
20 7024879 1 WASHER, Felt
21 7061272 1 KIT, Height Adjusting Lever (incl. items 22-24)
22 7090376 2 NUT, #10-32 Hex Nyloc
23 7033967 1 LEVER, Height Adjusting (Black)
24 7091289 2 SCREW, #10-32 x 5/8, Hex Washer Self-Tap, GR 5
25 7026420 1 GRIP, Flat Bar
26 7024549 1 PINION, RH Drive
27 7024550 1 PINION, LH Drive
28 7091194 2 WASHER, 17/32” Flat
29 7024573 2 SHIELD, Dust
30 7074207 1 WELDMENT, Rear Axle
tionItem Qt
Note
Footnotes:
NOTE: * These three parts make up 7054114, Transmission Lever Assembly.
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
13
TP 400-5062-C-WB-N
DECALS
Manual No. 7006204
TP 400-5062-C-WB-N
14
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
DECALS
p
y
Part No Descri
1 7100180 1 DECAL, SNAPPER Name Plate
2 7100182 1 DECAL, SNAPPER Control Panel
3 7027255 1 DECAL, SNAPPER, Panel
4 7075618 1 DECAL, SNAPPER
5 7072921 1 DECAL, Warning (Deck)
6 7022841 1 DECAL, Warning (International Symbol)
7 7013010 1 DECAL, Danger (Keep Hands and Feet Away)
8 7029776 1 DECAL, European Community (CE)
9 7028454 1 DECAL, Height Control Instruction (Euro)
10 7029779 1 DECAL, Spark Plug International Symbol
11 7075475 1 DECAL, Speed Shift- ELP, ECLP
12 7046924 1 DECAL, Chute Deflector (Cast)
13 7046357 1 DECAL, Warning 1997
14 7073462 1 DECAL, Caution Symbols
15 7101084 1 DECAL, Warning Euro Multi-Panel
16 7029782 1 DECAL, OPC Bail International Symbol
17 7029784 2 DECAL, Chute/International Warning
18 7075532 1 DECAL, Throttle Control, B&S
19 7028439 1 DECAL, Convertible Mower
20 7074135 1 DECAL, Noise, 100 dB (shown)
20 7100579 1 DECAL, Noise, 98 dB (not shown)
21 7011279 1 DECAL, 2005 Year of Manufacture
21 7100611 1 DECAL, 2006 Year of Manufacture (not shown)
21 7101285 1 DECAL, 2007 Year of Manufacture (not shown)
tionItem Qt
Note
Footnotes:
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
15
TP 400-5062-C-WB-N
ACCESSORIES
Manual No. 7006204
TP 400-5062-C-WB-N
16
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
ACCESSORIES
p
y
Part No Descri
1 7028445 1 GRASS BAG, SNAPPER Platinum Series GRASS CATCHER PARTS
2 7044915 1 FRAME, Catcher Weldment GRASS CATCHER PARTS
3 7026421 1 GRIP, Rectangular (Black) GRASS CATCHER PARTS
4 7026390 1 PLUG, Mulching MULCHING PARTS
5 7026714 1 CHUTE, Side Discharge (incl. WARNING Decal, p/n 7013010) DISCHARGING PARTS
tionItem Qt
Note
Footnotes:
Manual No. 700620421" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
17
TP 400-5062-C-WB-N
Parts Manual fo
r
21" CAST DECK WALK BEHIND MOWER
EUROPEAN SERIES 3
IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION
TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED
Briggs & Stratton Yard Power Products Group
535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967
www.snapper.com
Copyright © 2008
Milwaukee, WI USA. All Rights Reserved
Briggs & Stratton Corporation
Manual No. 7006204
Revision C,
TP 400-5062-C-WB-N
8/12/2008
Loading...