Snapper EI75225 User Manual
Parts Manual fo
r
E
6
E
E
E
E
TWO-STAGE INTERMEDIATE FRAM
SNOW THROWER
SERIES 5 & 6
MODEL
EI5225
EI75225
EI7524
EI75246
EI8245
EI85245
I5225
I75225
I75246
I8245
I85245
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 2,
McDonough, GA, 30253 U.S.A.
10/3/2006
Manual No. 7006070
TP 400-5038-2-IS-N
s
PAGE GROUP
4
8
10
12
14
16
20
24
30
32
34
UPPER HANDLES, DASH, CONTROLS
CHUTE CRANK CONTROL
COLLECTOR HOUSING (3 Piece Bolted)
DISCHARGE CHUTE
AUGERS, IMPELLER, GEAR CASE, SHAFT
TRACTION DRIVE GROUP
ENGINE, PULLEYS, IDLER (5 HP Tecumseh)
ENGINE, PULLEYS, IDLER (7-1/2, 8, 8-1/2 HP Briggs)
WHEELS
DECALS
ELECTRIC START COMPONENTS
Table Of Content
SERIES 5 & 6
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
3
TP 400-5038-2-IS-N
UPPER HANDLES, DASH, CONTROLS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
4
SERIES 5 & 6
UPPER HANDLES, DASH, CONTROLS
p
y
Part No Descri
1 1919438 2 NUT, 5/16-18 Hex Nyloc or 7091298
2 1726727 1 BRACKET, Snow Stick- Lower
3 1921332 4 SCREW, 5/16-18 x 3/4” Hex Head Cap or 7091318
4 7027426 1 CLUTCH CABLE, Auger Drive- RH part number is stamped on cable
5 1726574 1 HANDLE, Upper, Right Hand
6 1722638 1 GRIP, Clutch, RH
7 1726317 2 GRIP, Foam, Black
8 1722460 3 HAIR PIN
9 1666255 1 ROD, Shift, Lower
10 1916622 2 NUT, 1/4-20 2B Hex
11 1916964 3 LOCKWASHER, 1/4” Spring
12 1931317 2 BOLT, 1/4-20 x 2” Short Square Neck Carriage, GR 5
13 1720238 1 ROD, Upper, Shift
14 1668524 2 BLOCK, Pivot
15 1720240 1 WELDMENT, Shift Rod Pivot
16 1715123 1 SPRING, Compression
17 1918452 1 COTTER PIN, .125 x 1.00
18 1668185 2 BUSHING, .500 ID x .750 OD x .25
19 1924361 1 WASHER, 1/2” Flat (.531 ID x 1.250 OD x .08 Thick)
20 1668523 1 WELDMENT, Shift Rod
21 1960705 1 SCREW, 1/4-20 x 2-1/4” Hex Flange Lock
22 1921319 2 WASHER, .250 (.27 ID x .62 OD)
23 1726734 1 KNOB, Tapered - 3/8-16 Internal Thread- Red
24 1726983 1 WELDMENT, Dash
25 1726572 1 HANDLE, Lower
26 7035744 2 WING KNOB, 5/16-18
27 7090391 2 WASHER, 5/16” Internal Tooth Lock
28 1960686 4 NUT, 5/16-18 Hex Flange Nyloc
29 1919326 2 WASHER, .312 (.34 ID x .75 OD) or 7014098
30 1722633 1 ASSEMBLY, Rod w/Pin includes items 32, 47, 54, 55 &
31 1722690 1 SPRING, Compression
32 1960519 1 PUSH NUT
33 1722630 1 ROD, Hold Down
34 1960662 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
35 1722667 1 GRIP, Clutch, LH
36 1923358 2 NUT, 1/4-20 Hex Centerlock
37 1715655 2 SPACER, Handle
tionItem Qt
Note
56.
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
5
TP 400-5038-2-IS-N
UPPER HANDLES, DASH, CONTROLS
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
6
SERIES 5 & 6
UPPER HANDLES, DASH, CONTROLS
p
y
Part No Descri
38 1726573 1 HANDLE, Upper, Left Hand
39 1922837 2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap
40 1715654 2 SPACER, .268 ID x .394 x .165
41 1960671 2 SCREW, 1/4-20 x 3/4” Pan Head Torx Self-Tap
42 1921221 5 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
43 1722631 1 LEVER, Pivot
44 1920397 2 NUT, 1/4-20 Hex Nyloc
45A 7075909 1 SNOW STICK
45B 1733209 1 SNOW STICK w/Brush replaces 7075909
46 7091267 1 NUT, #10-24 Hex Center Lock
47 1722632 1 ROD, Hand Control not shown; part of item 30
48 7071895 1 HOLDER, Snostik- Upper
49 7027425 1 CLUTCH CABLE, Ground Drive- LH parts number is stamped on
50 7091189 4 BOLT, 5/16-18 x 2” Curved Head Square Neck GR 2
51 7090011 1 WASHER, #10 Internal Tooth Lock
52 7091266 1 SCREW, #10-24 x 2” Hex Washer Head Machine, GR 5
53 1917356 4 LOCKWASHER, Spring .312 or 7091315
54 1722635 1 BUSHING, .250 ID x .375 OD x .750 not shown; part of item 30
55 1722634 1 PIN, Clevis not shown; part of item 30
56 1722613 1 SPRING, Compression not shown; part of item 30
tionItem Qt
Note
cable
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
7
TP 400-5038-2-IS-N
CHUTE CRANK CONTROL
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
8
SERIES 5 & 6
CHUTE CRANK CONTROL
p
y
Part No Descri
1 1960093 1 PUSH NUT, Pal. .375 Dia. Stud Cap
2 1714084 1 KNOB, Spinner
3 1667588 3 BUSHING, .376 x .437 x .20
4 7028152 1 ROD, Chute, Upper
5 1960074 1 CLIP, .093 Dia. Hair Pin
6 1720577 1 SPLICE, Chute Handle
7 1926228 1 SPRING PIN, .156 x 1.000
8 1726939 1 ROD, Chute Lower
9 1918452 1 COTTER PIN, .125 x 1.00
10 1718793 1 BRACKET, Universal Gear
11 1921319 3 WASHER, .250 (.27 ID x .62 OD)
12 1960518 2 RETAINER, 1/4” Bolt
13 1960252 2 BOLT, 1/4-20 x 5/8” Short Square Neck Carriage
14 1718593 2 GEAR, Universal
15 1960103 1 WASHER, 3/8” Flat- Black
16 1916168 1 SPRING PIN, .125 x .750
17 7028159 1 WORM SHAFT
18 1960294 2 NUT, 1/4-20 Hex Flange Lock
19 7014001 1 ROLL PIN, 1/8 x 3/4”
20 7021828 1 WORM
21 7011724 1 WASHER, .44 x .78 x .025 Curved
22 7028162 1 BRACKET, Worm
23 7091070 1 NUT, 5/16-18 Hex Flange Lock
24 7091138 1 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR 5
25 7090539 1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
9
TP 400-5038-2-IS-N
COLLECTOR HOUSING (3 Piece Bolted)
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
10
SERIES 5 & 6
COLLECTOR HOUSING (3 Piece Bolted)
p
y
Part No Descri
1 7072542 1 END PLATE, RH- Auger Housing- Red
2 7072547 1 WELDMENT, Auger Housing - 22” - Red
2 7072567 1 WELDMENT, Auger Housing - 24” - Red
3 1930659 3 RETAINER NUT, 5/16-18
4 7072544 1 END PLATE, LH- Auger Housing- Red
5 7300099 1 BLADE, Scraper- 22” replaces 1675080
5 7200098 1 BLADE, Scraper- 24” replaces 1725352
6 1726457 2 BEARING, Auger
7 1665982A 1 RETAINER, Bearing
8 108202 1 BALL BEARING
9 7072552 2 SKID SHOE, Reversible- Red or 1727854
10 1916965 4 WASHER, 3/8” Split Lock or 7091320
11 1931315 12 BOLT, 1/4-20 x 1/2” Short Square Neck Carriage, GR 5 or 7091604
12 7090204 3 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or 1925205
13 1930641 12 NUT, 1/4-20 Hex Flange Lock Large
14 1960711 4 BOLT, 3/8-16 x 3/4” Square Neck Carriage or 7091923
15 1924940 4 WASHER, 3/8” Flat or 7090122
16 1960687 4 NUT, 3/8-16 Hex Nyloc
17 7091742 6 SCREW, 5/16-18 x 1” Hex Washer Self-Tap
18 7072549 2 CAP, Bearing, Red
19 7091315 3 WASHER, 5/16” Split Lock or 1917356
20 7091208 5 BOLT, 1/4-20 x 7/16” Short Square Neck Carriage, GR 5
21 7091065 5 NUT, 1/4-20 Hex Flange Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006070TWO-STAGE INTERMEDIATE FRAME
SERIES 5 & 6
11
TP 400-5038-2-IS-N
DISCHARGE CHUTE
Manual No. 7006070 TWO-STAGE INTERMEDIATE FRAME
TP 400-5038-2-IS-N
12
SERIES 5 & 6
Loading...