Snapper CP215518HV, CRP216018KWV, CP216018KWV User Manual
Parts Manual fo
r
D
S
V
21" STEEL DECK WALK BEHIN
COMMERCIAL MOWER
SERIES 18
MODEL
CP215518HV
CP216018KW
CRP216018KWV
COPYRIGHT ©2005
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 1,
McDonough, GA, 30253 U.S.A.
8/3/2005
Manual No. 7006140
TP 400-5048-1-WB-N
s
PAGE GROUP
4
8
10
12
14
16
18
22
24
26
28
30
32
34
36
HANDLES & CONTROLS (Upper End)
HANDLES & CONTROLS (Lower End)
CUTTING DECK, BLADE
FRONT WHEEL BRACKET, LATCHES
REAR WHEEL BRACKETS, LATCHES
FRONT AND REAR WHEELS
DRIVE SYSTEM SELF-PROPELLED
TRANSMISSION (DIFFERENTIAL)
SIDE CHUTE ADAPTER
ACCESSORY GRASS BAG
THROTTLE CONTROLS/ENGINE SPECS
DECALS
SNAPPERIZER ACCESSORY
ACCESSORY THATCHERIZER
RECYCLING KITS ACCESSORY
Table Of Content
SERIES 18
Manual No. 700614021" STEEL DECK WALK BEHIND
3
TP 400-5048-1-WB-N
HANDLES & CONTROLS (Upper End)
Manual No. 7006140 21" STEEL DECK WALK BEHIND
TP 400-5048-1-WB-N
4
SERIES 18
HANDLES & CONTROLS (Upper End)
p
y
Part No Descri
1 7074411 1 HANDLE, Upper
2 7074156 1 HANDLE, Middle
3 7074418 1 BAIL, OPC Control
4 7034872 1 CLIP, Zone Control
5 7074141 1 CABLE, Zone Control (56-5/16” Long) CP216018KWV &
-- 7029344 1 CABLE, Zone Control (49.98” Long) CP215518HV
6 7074473 1 HANDLE, Clutch
7 7028407 1 GRIP, International Symbol
8 7034604 1 CABLE, Clutch Control (41-1/4” Long)
9 7012121 1 COVER, Vinyl
-- 7075305 1 COVER, Grip CP215518HV
10 7012122 1 SPRING, Clutch- 21S
11 7074003 1 BRACKET, Shift
12 7074133 1 ROD, Speed Control (1/4-28 thread)
13 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
14 7031961 2 WASHER, 7/16” Flat
15 7028465 2 WASHER, Nylon
16 7091190 2 BOLT, 5/16-18 x 1-1/2” Curved Head
17 7091576 2 NUT, 1/4-20 Hex Was 91100
18 7023813 3 CLIP, Wiring Harness
19 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5
20 7026219 1 CLAMP, 7/8” Double Cable
21 7090505 2 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
22 7090053 2 WASHER, 1/4” Internal Tooth Lock Was 91023
23 7074140 1 CONTROL PANEL (w/o Electrical Switch Hole)
24 7091200 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx)
25 7014343 2 BUSHING, .27 x .35 x .4 Flange
26 7023792 1 PIN, 1/4 x 1-1/2”
27 7091020 1 PUSH-NUT, 1/4”
28 7023810 1 FOAM GRIP, 18.75” long
29 7090391 3 WASHER, 5/16” Internal Tooth Lock
30 7029366 1 DECAL, Commercial, WBM
31 7091511 2 NUT, 5/16-18 Hex, GR 5 Was 91069
32 7029782 1 DECAL, OPC Bail (International Symbol)
33 7028488 1 GUIDE, Rope (1/4-20 thread)
34 7028568 1 WASHER, Belleville
35 7091585 1 NUT, 3/8-16 Hex Center Lock
tionItem Qt
Note
CRP216018KWV
Footnotes:
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18
5
TP 400-5048-1-WB-N
HANDLES & CONTROLS (Upper End)
Manual No. 7006140 21" STEEL DECK WALK BEHIND
TP 400-5048-1-WB-N
6
SERIES 18
HANDLES & CONTROLS (Upper End)
p
y
Part No Descri
36 7074113 1 LEVER, Shift
37 7075182 1 KNOB, Shift
38 7091167 1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine
39 7091018 1 NUT, #8-32 Hex
40 7090188 3 WASHER, 3/8” Flat
41 7034162 1 COTTER PIN, 5/16 Self Lock
42 7024641 1 TIE, Wire, 1.29 long, black
43 7076978 2 NUT, 1/4-28 Hex Nyloc
44 7012080 2 CABLE-TIE, 7”
45 7078026 1 THROTTLE CONTROL, 50.81”, Honda CP215518HV
-- 7074138 1 THROTTLE CONTROL, 6.0 KWV CP216018KWV &
46 7075308 1 THROTTLE KNOB
tionItem Qt
Note
CRP216018KWV
Footnotes:
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18
7
TP 400-5048-1-WB-N
HANDLES & CONTROLS (Lower End)
Manual No. 7006140 21" STEEL DECK WALK BEHIND
TP 400-5048-1-WB-N
8
SERIES 18
HANDLES & CONTROLS (Lower End)
p
y
Part No Descri
1 7033985 1 HANDLE, Lower LH (Adjustable)
2 7033986 1 HANDLE, Lower RH (Adjustable)
3 7090799 2 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR 5 Was 91026
4 7091601 2 NUT, 5/16-18 Hex Flange Lock GR 5 Was 91070
5 7046707 2 STRAP, Handle
6 7090095 4 NUT, 1/4-28 Hex, GR 5
7 7015753 2 BALL JOINT, 1/4-28
8 7090053 4 WASHER, 1/4” Internal Tooth Lock
9 7090595 5 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR 5
10 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 90585
11 7073822 1 BRACKET, Bell Crank
12 7013849 1 SPACER, .33 x .63 x .156
13 7073913 1 BELL CRANK
14 7091130 1 WASHER, .33 x .88 x .09 Flat
15 7091904 1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5
16 7091190 4 BOLT, 5/16-18 x 1-1/2” Curved Head
17 7091575 1 NUT, 5/16-18 Hex Center Lock Was 91067
18 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR5
19 7012114 1 BUSHING, Differential
20 7090895 1 NUT, 5/16-18 Tee
21 7032408 1 GUIDE, Lower V-Belt
22 7091606 1 NUT, 5/16-18 Hex, GR 5 Was 91074
29 7090391 4 WASHER, 5/16” Internal Tooth Lock
31 7091511 4 NUT, 5/16-18 Hex, GR 5 Was 91069
tionItem Qt
Note
Footnotes:
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18
9
TP 400-5048-1-WB-N
CUTTING DECK, BLADE
Manual No. 7006140 21" STEEL DECK WALK BEHIND
TP 400-5048-1-WB-N
10
SERIES 18
CUTTING DECK, BLADE
p
y
Part No Descri
1 7057663 1 * DECK, Mower (incl. painted “HV” Deck w/Wheel Brackets &
Decals)
-- 7057884 1 * ASSEMBLY, Non-Adjustable Air, 21” Deck Was 57667 for CRP216018KWV
2 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 90585
3 7090731 2 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR 5 or 92061
4 7091169 1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR 5
5A 7090324 3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts (Kawasaki)
5B 7090238 2 SCREW, 5/16-24 x 1” Hex Head Cap GR5 engine mount bolts (Honda)
6 7090700 1 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock, GR5 engine mount bolts (Honda)
7 7031961 1 WASHER, 7/16” Flat
8 7091315 2 WASHER, .32 x .58 x .08 Split Lock on engine mount bolts (Honda)
9 7090167 1 SCREW, 3/8-24 x 2” Hex Head Cap, GR 5 CP215518HV
10 7090228 4 SCREW, 5/16-24 x 21/32” Oval Head Machine
11 7091297 4 NUT, 5/16-24 Hex, GR5 Was 90223
12 7044770 3 1/16” THICK SPACER, Blade Hub CRP216018KWV
13 7012063 2 WASHER, Cone
14A 7026691 1 BLADE, Cutter (Standard Lift) CP215518HV & CP216018KWV
14B 7026407 1 BLADE, 21” Ninja (Quad Edge) CRP216018KWV
15 7015626 1 HUB, Blade Drive 25mm I.D. CP216018KWV,
-- 7012927 1 HUB, Blade Drive 7/8” CP215518HV
16 7010783 2 KEY, #505 Hi-Pro CP215518HV
-- 7091214 1 KEY, #HP-506 Hi-Pro CP216018KWV &
17 7090201 1 SCREW, 5/16-18 Hex Socket Head
18 7015780 1 PULLEY-Engine (25mm I.D. x 2-1/8 O.D.) CP216018KWV &
-- 7021822 1 PULLEY, Engine (1” I.D. x 2.275” O.D.) CP215518HV
19 7090391 4 WASHER, 5/16” Internal Tooth Lock
20 7032558 2 AIR LIFT
21 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001
22 7011791 2 RETAINER, 5/16” Bolt
23 7011762 1 COVER, Spark Plug not shown
-- 7060785 -- KIT, Air Lift (Incl. items 10, 11, 19 & 20)
24 7074568 1 COVER, Belt (Baffle)
25 7045264 2 PLUG, 5/16” Hole
26 7091601 1 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070
27 7046780 2 PLUG, Hole, Polyethylene
-- -- 1 *ENGINE, 5.5HP Honda Commercial Model GXV160, Type KA12;
-- -- 1 *ENGINE, 6HP Kawasaki Model FJ180V, Type AS13-R;
tionItem Qt
Note
CP215518HV & CP216018KWV
CRP216018KWV
CRP216018KWV
CRP216018KWV
used on CP215518HV
used on CP216018KWV &
CRP21601/8KWV
Footnotes:
Note* includes painted deck and wheel brackets
Note* Purchase engine parts from engine manufacturer dealer.
Manual No. 700614021" STEEL DECK WALK BEHIND
SERIES 18
11
TP 400-5048-1-WB-N
FRONT WHEEL BRACKET, LATCHES
Manual No. 7006140 21" STEEL DECK WALK BEHIND
TP 400-5048-1-WB-N
12
SERIES 18
Loading...