Snapper Clean Sweep Twin Catcher User Manual

Download

ATTACHMENT

OPERATOR’S MANUAL

Clean Sweep Twin Catcher

Mfg. No. Description

1695171 Clean Sweep Twin Catcher

1733743

Rev. 03

Rev. Date 12/2006

TP 100-4406-03-AT-N

Clean Sweep

Twin Catcher

Safety Rules & Information

General Warnings............................................2

Safety Decals ..................................................2

General Operating Instructions

Before Operation.............................................3

Mowing with the Catcher.................................3

After Operation................................................3

Storing the Grass Catcher...............................3

Initial Installation

Hitch Installation....................................................4

Component Installation..........................................5

Bag, Chute and Tube Installation ..........................8

Normal Removal & Installation

Collector Installation......................................11

Collector Removal.........................................12

NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position.

Table of Contents

Safety Rules & Information

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed.

SAFETY DECALS

This unit has been designed and manufactured to provide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.

Although reading this manual and the safety instructions it contains will provide you with the necessary basic knowledge to operate this equipment safely and effectively, we have placed several safety labels on the unit to remind you of this important information while you are operating your unit.

All DANGER, WARNING, CAUTION and instructional messages on your rider, attachments and mower should be carefully read and obeyed. Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your product.

If any decals are lost or damaged, replace them at once. See your local dealer for replacements.

• Know the unit’s controls and how to stop quickly. READ THE OPERATOR’S MANUALS.

• Read and obey all safety decals.

• Only allow responsible adults, who are familiar with the instructions, to operate the unit.

• Disengage the PTO. Shut off the engine and wait for all moving parts to stop before attaching, adjusting, or disconnecting any part of the collection system.

• Check the collection system to make sure it is bolted tightly to the unit.

• DO NOT operate the unit without either the entire grass catcher or the deflector in place.

• Turn off the PTO to disengage the blades when not mowing.

• DO NOT mow in reverse unless absolutely necessary. Always look down and behind before and while travelling in reverse.

• DO NOT turn sharply when travelling alongside a building or any object. Slow down before turning.

• DO NOT carry passengers.

• When collection system is removed from the mower deck, the deflector must be properly installed.

• Collector bags are subject to deterioration and wear during normal use. Inspect the bag periodically for tears, holes, or weak spots and replace with a new

bag that meets manufacturer’s durability standards.

• If the mower stalls or the collector chute plugs:

1. Disengage the PTO;

2. Stop the engine and remove the key;

3. Set the parking brake, and wait for all moving parts to stop.

4. Remove the foreign object or clear the chute with a piece of wood before restarting the engine.

NEVER place hands into COLLECTOR OR MOWER housing to clear jammed objects. Blower OR MOWER may rotate when object is removed.

• For added stability and to prevent tipping or loss of control:

a. Use reduced speed on uneven ground and when turning corners.

b. Reduce loads on hillsides. It is recommended that the collection system be kept only half full when negotiating any slopes. Start mowing on slopes when the collection system is empty.

c. Mow up and down the face of slopes; never across the face of any slope.

• Never operate on slopes greater than 17.6%

(10°).

GENERAL WARNINGS

TP 600-2562-01-AT-SMA

Attachment Decal

These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation.

Decal - WARNING Thrown Objects Hazard Part Number 1732819

Read and obey all operation and warning decals.

WARNING

Thrown objects hazard

• Objects thrown by the mower can seriously injure or kill you.

• Do not open the hopper while the mower blades are turning.

• Do not operate the mower without the complete catcher in place.

1732819

Before Operation

Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades.

Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged.

For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important.

For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher lid are free from grass and debris.

Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover.

Mowing with the Catcher

Always operate with throttle at full speed when mowing. Grass should be cut often, and not too short. If grass is

too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width of the mower to prevent clogging. If grass is long, operate with mower in high cutting position for first pass, cutting again in a lower position on a second pass.

Do not open the cover with mower engaged.

If a large amount of cut grass is spilling out from under deck, the tube may be plugged or the bags may be full— discontinue mowing, stop the unit, disengage the PTO, shut off the engine and then empty the catcher or clear the tube.

General

Operating Instructions

WARNING

ALWAYS shut off the tractor. Disengage the PTO, and allow all moving parts to stop BEFORE disconnecting or clearing tube, or emptying catcher.

Before leaving the operator’s position for any reason, engage the parking brake, disengage the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider and mower free of grass, leaves and excess grease. Do not stop or park rider over dry leaves, grass or combustible materials.

Never operate on slopes greater than 17.6% (10°).

After Operation

Remove any debris from the the screen on the underside of the lid.

The blower housing and tube should be removed for cleaning.

Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover.

Storing The Grass Catcher

Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the screen on the underside of the lid.

If paint has been scratched on metal parts, touch up with paint, or apply a thin film of oil to prevent corrosion.

Store in a dry area. Dry thoroughly before storing for a long period of time. Always store away from moisture.

Do not leave grass in bagger containers. Empty containers after each use and before storing. Failure to do so may result in spontaneous combustion which could develop into a fire.

CAUTION

Before you begin operating the unit be certain you have read all of the safety and operational information of this instruction sheet, as well as the Operator’s Manual for the tractor and any other attachments.

Initial Installation

Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s).

WARNING

Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support

Figure 3. Hitch Installation A. Hitch B. Shoulder Bolt C. Pin D. Hole in Draw Bar E. Hair Pin

Initial Installation

HITCH INSTALLATION

1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the threaded side (B) is on the inside of tractor.

2. Secure the 5/16-18 shoulder bolt (D) as shown.

3. Repeat on the other side.

Figure 2. Frame Plate Reinforcement Installation A. Frame Reinforcement B. Rear Frame Support C. Frame Support Hole D. Capscrew, 5/16-18 x 1-1/4 (new) E. Locknut, 5/16-18 (existing) F. Capscrew, 5/16-18 (existing)

4. Remove existing nuts and capscrews from both sides and rear frame support holes (C, Figure 2)

5. Secure frame reinforcement (A) to the inside of the rear frame support (B) using new 5/16-18 x 1-1/4 capscrews (D) and existing 5/16-18 capscrews and locknuts (E & F) as shown.

6. Slide the hitch (A, Figure 3) on right side and left side shoulder bolt (B) while sliding pin (C) into hole (D) as shown. Secure with hair pin (E).

Pin Installation

Component Installation

PIN INSTALLATION ON LOWER CHUTE

1. Insert the head of pin (C, Figure 4) through front hole of lower chute (A). Secure with 1/4-20 x 5/8 carriage bolt (D) and 1/4-20 lock nut (B) as shown.

CARRIAGE BOLT AND PUSH NUT INSTALLATION MOWER DECK HOUSING

1. Secure the 5/16-18 x 3/4 carriage bolts (A, Figure 5) onto mower deck housing (C) using 5/16 push nuts (B).

Note: Retaining carriage bolts with push nuts is optional.

Figure 4. Install Pin A. Lower Chute B. Locknut, 1/4-20 C. Pin D. Carriage Bolt, 1/4-20 x 5/8

Figure 5. Install Mounting Plate A. Carriage Bolts, 5/16-18 x 3/4 B. Push Nuts, 5/16 C. Mower Deck Housing

Figure 6. Handle to Tube Installation A. Handle B. Locknuts, KEPS, 1/4-20 C. Screw, Slotted, 1/4-20 x 1/2 D. Screw, Slotted, 1/4-20 x 1 E. Strap, Rubber F. Locknut, Center Lock, 1/4-20

HANDLE INSTALLATION

1. Install the handle (A, Figure 6) using 1/4-20 x 1/2 screw (C) and 1/4-20 locknut (B) for rear hole. Use 1/4-20 x 1 screw (D) and 1/4-20 locknut (B) as shown. Tighten hardware.

2. Install the strap (E) to screw (D) securing with 1/4-20 locknut (F).

Component Installation

Figure 8. Install Upright Support A. Hitch B. Upright Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16

INSTALL UPRIGHT SUPPORT TO HITCH

1. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and locknuts (D) as shown.

INSTALL BAG AND COVER SUPPORT

1. Install the bag and cover support (B, Figure 9) to upright support (A) using reinforcement plate (C) and 3/8-16 x 1 capscrews (D) and 3/8-16locknuts (E) as shown.

Figure 9. Install Bag and Cover Support A. Upright Support B. Bag and cover Support C. Reinforcement Plate D. Capscrews, 3/8-16 x 1 E. Locknuts, 3/8-16

Cover Installation

Figure 10. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots

INSTALL COVER ASSEMBLY

1. Attach cover assembly (B, Figure 10) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown.

Bag and Chute Installation

Figure 10. Install Lower Discharge Chute A. Lower Chute B. Knob, 5/16-18 C. Front Carriage Bolt, 5/16-18 x 3/4 D. Wing Nut, 5/16 E. Discharge Deflector F. Rear Carriage Bolt, 5/16-18 x 3/4 G. Hinge Bracket

LOWER DISCHARGE CHUTE INSTALLATION

1. Lift discharge deflector up (E, Figure 10).

2. Place the front hole of the lower chute (A) onto carriage bolt (C) as shown. Slide front edge of lower chute (A) under hinge bracket (G).

3. Place the rear hole of the lower chute (A) onto carriage bolt (F) as shown.

4. Secure knob (B) onto carriage bolt (C) as shown.

5. Secure wing nut (D) onto carriage bolt (F) as shown.

INSTALL COLLECTOR BAGS

1. Raise the cover (A, Figure 9).

2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D).

Note: It may be necessary to fold seat forward to allow cover to stay in the raised position.

Figure 9. Install Collector Bags A. Cover B. Collector Bags C. Grass Bag Hanger D. Bag Hanger Post

Tube Installation

Figure 11. Install Upper Tube to Cover A. Upper Tube B. Cover C. Ridge, Upper Tube D. Ridge Cutout

Figure 12. Install Middle Tube A. Lower Chute B. Strap, Rubber C. Pin D. Middle Tube E. Upper Tube F. Screw, 1/4 x 3/4

42” & 38” Frame Hung Mowers

CONNECTING UPPER & MIDDLE TUBE

1. Slide the upper tube (A, Figure 11) into cover (B) aligning ridge (C) with cutout (D) as shown.

2. Slide middle tube (D, Figure 12) into upper tube (E).

3. Slide middle tube (D) over boot (A). Pull strap (B) and place hole completely over pin (C).

4. In the second hole from the bottom secure upper tube (E) over middle tube (D) using 1/4 x 3/4 screw (F) and correct hole.

Normal Removal & Installation

Collector Installation

Note: See previous pages for more detailed installation and operation instructions if necessary.

1. Lift discharge deflector up (E, Figure 13).

2. Place the front hole of the lower chute (A) onto carriage bolt (C) as shown. Slide front edge of lower chute (A) under hinge bracket (G).

3. Place the rear hole of the lower chute (A) onto carriage bolt (F) as shown.

4. Secure knob (B) onto carriage bolt (C) as shown.

5. Secure wing nut (D) onto carriage bolt (F) as shown.

6. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and locknuts (D) as shown.

7. Install the bag and cover support (B, Figure 9) to upright support (A) using reinforcement plate (C) and 3/8-16 x 1 capscrews (D) and 3/8-16locknuts (E) as shown.

8. Attach cover assembly (B, Figure 10) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown.

9. Raise the cover (A, Figure 9), and attach collector bags (B) using grass bag hanger (C) to bag hanger post (D).

10.Slide the upper and middle tube (J, Figure 14) aligning ridge (L) with cutout (M) as shown.

9. Slide middle and upper tube (J) over lower chute (H). Pull strap (K) and place hole completely over pin (I).

Figure 13. Install Lower Discharge Chute A. Lower Chute B. Knob, 5/16-18 C. Front Carriage Bolt, 5/16-18 x 3/4 D. Wing Nut, 5/16 E. Discharge Deflector F. Rear Carriage Bolt, 5/16-18 x 3/4 G. Hinge Bracket

Normal Removal

A. Hitch Support Assembly G. Middle & Upper Tube B. Cover H. Lower Chute C. Pin I. Pin D. Hair Pins J. Strap Middle E. Bag K. Ridge F. Grass Bag Hanger L. Ridge Cutout

Figure 14. Normal Installation & Removal

Collector Removal

1. Unhook strap (J, Figure 14) from pin (I). Remove middle and upper tube (G) from cover (B).

2. Lift up cover (B) remove and empty bags (E).

3. Remove hair pins (D) and pins (C) and remove cover (B).

Note: To prevent loss of parts reinstall pins (C) and hair

pins (D) in support assembly hinge pivots (E, Figure

10).

WARNING

OPERATION WITHOUT BAGGER For operation without bagger, the mower

deflector MUST be properly installed in the down position and retained by the spring latch.

4. Remove hitch support assembly (A, Figure 14).

5. Lift discharge deflector up (E, Figure 13).

6. Remove wing nut (D) from carriage bolt (F).

7. Remove the knob (B) from carriage bolt (C).

8. Remove the lower chute (A) from carriage bolt (F).

9. Remove lower chute (A) from carriage bolt (C).

Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253

www.Snapper.com Briggs & Stratton Yard Power Products Group

Snapper Clean Sweep Twin Catcher User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual