Parts Manual fo
r
E
V
V
V
V
INTERMEDIAT
REAR TINE TILLERS
SERIES 3, 4 & 5
MODEL
CICFR5505H
EICFR5004B
EICFR5004B
EICFR5505B
ICFR5004B
ICFR5505B
ICFR7005B
IR5003B
NIR5003B
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 9,
McDonough, GA, 30253 U.S.A.
2/28/2006
Manual No. 7006047
TP 400-5172-9-RT-N
s
PAGE GROUP
4
6
10
14
16
20
22
24
26
28
30
32
HANDLES, CONTROLS, WEIGHTS
MAIN CASE/GEARS (Series 3)
MAIN CASE/GEARS (Series 4&5)
TILLER HEAD COMPONENTS
SHIFT & DRIVE COMPONENTS
WHEELS, TIRES, RIMS
DECALS
DECALS (continued)
DECALS (continued)
DECALS (continued)
CULTIVATOR SHIELD KIT
HILLER - FURROWER KIT
Table Of Content
SERIES 3, 4 & 5
Manual No. 7006047INTERMEDIATE
3
TP 400-5172-9-RT-N
HANDLES, CONTROLS, WEIGHTS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
4
SERIES 3, 4 & 5
HANDLES, CONTROLS, WEIGHTS
p
y
Part No Descri
1 7018808 1 CABLE Clutch
2 7091575 5 NUT, 5/16-18 Hex Center Lock Was 91067
3 7015252 1 SPRING, Tine
4 7091601 12 NUT, 5/16-18 Hex Flange Lock Was 91070
5 7091681 7 BOLT, 5/16-18 x 1” Hex Flange Lock
6 7034746 1 BAR, Handle IRT
7 7036170 1 PANEL, Tiller Dash
8 7014681 2 BUSHING
9 7014682 1 COVER, Cable
10 7032593 1 CATCH, Bail
11 7018787 1 BAIL
12 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap GR5 Was 91066
13 7090831 1 SCREW, 5/16-18 x 2-3/4” Hex Head Cap GR5
14 7090361 12 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
15 7038221 1 SUPPORT, Handle
16 7091612 4 BOLT, 5/16-18 x 1-1/2” Sq. Neck Carriage GR5 Was 90582
17 7090861 4 BOLT, 5/16-18 x 1-3/4” Sq. Neck Carriage GR5
18 7091303 3 BOLT, 5/16-18 x 3/4” Square Neck Carriage GR5 Was 91072
19 7036171 1 BAR, Stand-Up
20 7035107 1 BOX, Weight
21 7011791 1 RETAINER, 5/16” Bolt (Black) not used on ICFR5004B
22 7038223 7 WEIGHT, Steel
23 7032496 2 BRACKET, Weight
24 7091076 16 WASHER, 5/16” Flat
7061794 1 BAG, Hardware - IR5003B Contains 2 each of P/N's 28725
tionItem Qt
Note
and 91606 (see Tiller Head
Component Page)
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
5
TP 400-5172-9-RT-N
MAIN CASE/GEARS (Series 3)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
6
SERIES 3, 4 & 5
MAIN CASE/GEARS (Series 3)
p
y
Part No Descri
7061821 ASSEMBLY, Case, Complete (Series 3) service kit
1 7034681 1 CASE HALF, Left Hand
2 7034682 1 CASE HALF, Right Hand
3 7034677 2 REINFORCEMENT, Case
4 7015597 1 CLAMP, Speedy
5 7091681 7 BOLT, 5/16-18 x 1” Hex Flange Lock
6 7015598 1 SEAL, Cap
7 7028672 1 SPACER, Tine Shaft (Short)
8 7028753 1 GASKET, Main Case IR5003B Tiller
9 7045130 1 SPACER, Main Shaft (.64” long)
10 7021977 1 PIN, Guide
11 7022512 1 SHAFT, Main Detent (4 Position)
12 7046604 1 FORK, Primary Shaft
13 7023252 1 SPRING, Compression Was 14500
14 7014469 1 BALL, Detent
15 7015405 1 CRANK, Shift
16 7015679 1 GASKET, Shift Arm Pivot
17 7015313 1 PIVOT, Shift Arm
18 7015409 1 PLUG, 1/2” Button
19 7015350 1 O-RING
20 7010756 1 BEARING, .625 x 1.37 x .435
21 7023849 1 SHAFT, Input
22 7028717 PINION, Input
23 7015136 1 SEAL, Oil
24 7015319 1 BEARING, Axle
25 7040609 1 WELDMENT, Axle (#40/34T)
26 7015347 1 CHAIN, Traction #40
27 7015318 1 SPACER, Wheel Shaft (.686” Thick)
28 7015348 2 SPACER, 5/8 x 1.11”
29 7018790 1 GEAR & SPROCKET
30 7045127 3 SHAFT, Gear
31 7053826 1 * ASSY, Tine Drive Gear, #50, Sprkt 10T, Gear 34T
32 7054412 1 * ASSEMBLY, Wheel Drive Gear
33 7042764 1 SPACER, Reverse (2.567” Long)
34 7051653 1 * ASSEMBLY, Reverse Idler
35 7015342 1 SEAL, Oil
36 7015343 1 O-RING
tionItem Qt
Note
Footnotes:
NOTE: * Part # 15339 DX Bearings are included, if purchased separately they must be pressed in.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
7
TP 400-5172-9-RT-N
MAIN CASE/GEARS (Series 3)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
8
SERIES 3, 4 & 5
MAIN CASE/GEARS (Series 3)
p
y
Part No Descri
37 7018869 1 BEARING, Tine Shaft
38 7029890 1 SPACER, Tine Shaft Long
39 7041726 1 WELDMENT, Tine Shaft (#50/18T)
40 7028476 1 CHAIN, Tine (Endless Roller) #50
41 7091513 4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap GR5 Was 91689
42 7011791 1 RETAINER, 5/16” Bolt (Black)
43 7091076 16 WASHER, 5/16” Flat
44 7091690 4 WASHER, 5/16” Split Lock
45 7091297 4 NUT, 5/16-24 Hex Was 91692
46 7090053 4 WASHER, 1/4” Internal Tooth Lock Was 91023
47 7090095 4 NUT, 1/4-20 Hex Was 91024
49 7011024 1 PLUG
48 7091946 21 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
50 7090873 3 WASHER, 7/16” Internal Tooth Lock
51 7090460 3 NUT, 7/16-20 Hex
52 7091601 8 NUT, 5/16-18 Hex Flange Lock Was 91070
53 7091584 6 NUT, 1/4-20 Hex Flange Lock Was 91065
54 7090953 3 SHIM-WASHER
55 7020938 1 SHIM WASHER, 5/8”
56 7090072 12 SCREW, 1/4-20 x 5/8” Hex Head Cap GR5 Was 79405
57 7091122 1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
58 7091819 3 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap Was 90362
59 7023514 1 O-RING, #012
60 7038647 1 REINFORCEMENT, R.H. Frame
61 7038648 1 REINFORCEMENT, L.H. Frame
62 7034680 1 BRACE, Belt Cover
63 7061174 1 SIDE PLATE Was 33415
64 7033962 1 BRACKET, Belt Cover- IRT
65 7033531 3 WASHER, Shim
66 7090606 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock Was 91510
tionItem Qt
Note
Footnotes:
NOTE: * Part # 15339 DX Bearings are included, if purchased separately they must be pressed in.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
9
TP 400-5172-9-RT-N
MAIN CASE/GEARS (Series 4&5)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
10
SERIES 3, 4 & 5
MAIN CASE/GEARS (Series 4&5)
p
y
Part No Descri
7057824 1 ASSEMBLY, Tiller Case
1 7034681 1 CASE HALF, Left Hand
2 7034682 1 CASE HALF, Right Hand
3 7034677 2 REINFORCEMENT, Case
4 7015597 1 CLAMP, Speedy
5 7091681 7 BOLT, 5/16-18 x 1” Hex Flange Lock
6 7015598 1 SEAL, Cap
7 7028672 1 SPACER, Tine Shaft (Short)
8 7028753 1 GASKET, Main Case IR5003B Tiller
9 7046787 1 SPACER, Main Shaft (.47” long)
10 7021977 1 PIN, Guide
11 7046786 1 SHAFT, Main Detent (5 Position) ICFR
12 7046604 1 FORK, Primary Shaft
13 7023252 1 SPRING, Compression Was 14500
14 7014469 1 BALL, Detent
15 7015405 1 CRANK, Shift
16 7015679 1 GASKET, Shift Arm Pivot
17 7015313 1 PIVOT, Shift Arm
18 7015409 1 PLUG, 1/2” Button
19 7015350 1 O-RING
20 7010756 1 BEARING, .625 x 1.37 x .435
21 7023849 1 SHAFT, Input
22 7046785 1 PINION, Input ICFR
23 7015136 1 SEAL, Oil
24 7015319 1 BEARING, Axle
25 7040609 1 WELDMENT, Axle (#40/34T)
26 7015347 1 CHAIN, Traction #40
27 7015318 1 SPACER, Wheel Shaft (.686” Thick)
28 7015348 2 SPACER, 5/8 x 1.11”
29 7018790 1 GEAR & SPROCKET
30 7045127 3 SHAFT, Gear
31 7057823 1 * ASSY, F&R Tine Drive Gear #50, Spkt 10T Gear 34T
32 7054412 1 * ASSEMBLY, Wheel Drive Gear
33 7046791 1 SPACER, Reverse Idler (1.245” long)
34 7051653 1 * ASSEMBLY, Reverse Idler
35 7015342 1 SEAL, Oil
36 7015343 1 O-RING
tionItem Qt
Note
Footnotes:
NOTE: * Part # 15339 DX Bearings are included, if purchased separately they must be pressed in.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
11
TP 400-5172-9-RT-N
MAIN CASE/GEARS (Series 4&5)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
12
SERIES 3, 4 & 5
MAIN CASE/GEARS (Series 4&5)
p
y
Part No Descri
37 7018869 1 BEARING, Tine Shaft
38 7029890 1 SPACER, Tine Shaft Long
39 7041726 1 WELDMENT, Tine Shaft (#50/18T)
40 7028476 1 CHAIN, Tine (Endless Roller) #50
41 7091513 4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap GR5 Was 91689
42 7011791 1 RETAINER, 5/16” Bolt (Black)
43 7091076 16 WASHER, 5/16” Flat
44 7091690 4 WASHER, 5/16” Split Lock
45 7091297 4 NUT, 5/16-24 Hex Was 91692
46 7090053 4 WASHER, 1/4” Internal Tooth Lock Was 91023
47 7090095 4 NUT, 1/4-20 Hex Was 91024
48 7091946 21 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
49 7011024 1 PLUG
50 7090873 3 WASHER, 7/16” Internal Tooth Lock
51 7090460 3 NUT, 7/16-20 Hex
52 7091601 8 NUT, 5/16-18 Hex Flange Lock Was 91070
53 7091584 6 NUT, 1/4-20 Hex Flange Lock Was 91065
54 7090953 3 SHIM-WASHER
55 7020938 1 SHIM WASHER, 5/8”
56 7090072 12 SCREW, 1/4-20 x 5/8” Hex Head Cap GR5 Was 79405
57 7091122 1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
58 7091819 3 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap Was 90362
59 7023514 1 O-RING, #012
60 7038647 1 REINFORCEMENT, R.H. Frame
61 7038648 1 REINFORCEMENT, L.H. Frame
62 7034680 1 BRACE, Belt Cover
63 7061174 1 SIDE PLATE Was 33415
64 7033962 1 BRACKET, Belt Cover- IRT
65 7033531 3 WASHER, Shim
66 7058469 1 * ASSY, Gear 16T (Incl. two 15339 DX Bearings)
67 7090606 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock Was 91510
68 7072801 1 WASHER, Shim .63 x 1.24 x .05
tionItem Qt
Note
Footnotes:
NOTE: * Part # 15339 DX Bearings are included, if purchased separately they must be pressed in.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
13
TP 400-5172-9-RT-N
TILLER HEAD COMPONENTS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
14
SERIES 3, 4 & 5
TILLER HEAD COMPONENTS
p
y
Part No Descri
1 7032553 1 HANDLE, Depth Bar
2 7091601 7 NUT, 5/16-18 Hex Flange Lock Was 91070
3 7091681 2 BOLT, 5/16-18 x 1” Hex Flange Lock
4 7034745 2 COVER, Side Tine IR5003B
5 7034684 1 COVER, Tine IR5003B
6 7091602 2 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock GR5
7 7034756 1 SPRING, Depth Bar IR5003B
8 7090361 8 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
9 7032494 1 PIN, Drag Shield (1/4” Dia. x 14-1/2” Steel Rod)
10 7091020 2 PUSHNUT, 1/4”
11 7032536 2 HINGE, Half
12 7091584 6 NUT, 1/4-20 Hex Flange Lock Was 91065
13 7036168 1 SHIELD, Drag
14 7075157 1 WELDMENT, Right Tine Was 49735
15 7028725 2 SCREW, 5/16-24 x 2” Hex Head Cap GR5
16 7091606 2 NUT, 5/16-24 Hex Center Lock
17 7075158 1 WELDMENT, Left Tine Was 49734
18 7038235 1 DEPTH-BAR
19 7091604 4 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
20 7034683 2 REINFORCEMENT, Rear Tine Cover
21 7090595 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock GR5
22 7038272 2 REINFORCEMENT, Front Tine Cover
23 7090290 3 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap Was 91686
24 7034755 1 BRACKET, Support IR5003B
25 7034757 1 PLATE, Latch
26 7091841 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap Was 91742
7057831 ASSEMBLY, Tine (Incl. items 27 thru 30) ICFR5004B, EICFR5004B,
27 7046798 1 WELDMENT, Tine Hub ICFR
28 7075142 8 TINE, 11.5” (.312” Thick) Was 38215
29 7014981 16 BOLT, 3/8-24 Shoulder
30 7090524 16 NUT, 3/8-24 Hex Top Lock GR C
7090289 8 NUT, 3/8-24 Hex Center Lock GR5 or B
tionItem Qt
Note
ICFR5505BV, CICFR5505HV,
EICFR5505BV and
ICFR7005BV only
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
15
TP 400-5172-9-RT-N
SHIFT & DRIVE COMPONENTS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
16
SERIES 3, 4 & 5
SHIFT & DRIVE COMPONENTS
p
y
Part No Descri
1 7047884 1 WELDMENT, Shift Lever
2 7091601 8 NUT, 5/16-18 Hex Flange Lock Was 91070
3 7013550 1 ROLL PIN 3/16 x 1”
4 7091303 3 BOLT, 5/16-18 x 3/4” Square Neck Carriage GR5 Was 91072
5 7090361 12 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
6 7090959 1 BOLT, 5/16-18 x 2-1/2” Short Neck Carriage GR5
7 7023851 1 TUBE, 3/8” I.D. x 1-7/8” Long
8 7011791 1 RETAINER, 5/16” Bolt (Black)
9 7038646 1 PLATE, Shift
10 7033349 2 BUSHING, Rubber
11 7017018 1 COVER, Shift
7046932 1 COVER, Shift
12 7091294 3 WASHER, 1/4” Flat Was 90055
13 7090290 3 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap Was 91686
14 7032843 1 BRACKET, Idler Pivot (shown)
7074749 1 BRACKET, Idler Pivot (not shown)
15 7090964 1 BOLT, 3/8-16 x 1-1/2” Flat Head Carriage
16 7032846 1 BRACKET, Idler Arm (shown)
7074748 1 BRACKET, Idler Arm (not shown)
17 7013849 1 SPACER, 5/16” I.D.
18 7010948 1 PULLEY, Idler ( 2” Outside Diameter)
19 7032662 1 GUIDE, Idler
20 7091585 1 NUT, 3/8-16 Hex Center Lock GR5 or B Was 90546
21 7090595 1 BOLT, 5/16-18 x 5/8” Hex Flange Lock GR5
22 7016314 1 WASHER, 11/32” Flat
23 7012830 1 KEY, 3/16 Sq. x 3/4” Long
24 7011194 1 PULLEY, Driven (9” Outside Dia.)
25 7090201 3 SCREW, 5/16-18 x 5/16” Hex Set
26 7015403 1 BELT, Drive (4L Kevlar 19.09” effective length)
27 7023852 1 SPACER, 5/8” Internal Dia.
28 7091102 1 WASHER, 1/4” Belville
29 7091122 1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
30 7033962 1 BRACKET, Belt Cover- IRT
31 7091946 21 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
32 7016022 1 COVER, Belt
33 7090951 1 NUT, 5/16-18 Hex Large Flange Center Lock
34 7091076 16 WASHER, 5/16” Flat
tionItem Qt
Note
Footnotes:
NOTE: * Purchase engine parts from engine manufacture dealer.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
17
TP 400-5172-9-RT-N
SHIFT & DRIVE COMPONENTS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
18
SERIES 3, 4 & 5
SHIFT & DRIVE COMPONENTS
p
y
Part No Descri
35 7090322 3 SCREW, 5/16-24 x 1/2” Hex Head Cap GR5 Was 91685
36 7090391 3 WASHER, 5/16” Internal Tooth Lock
37 7032541 1 GUIDE, Belt
38 7011809 1 PULLEY, Engine (2-1/2” Outside Dia.)
39 7015226 1 GUIDE, Belt (Finger)
40 7011762 1 BOOT, Spark Plug
41 7091841 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap Was 91742
* ENGINE, B&S 5 HP Mod 130202-0127-01
* ENGINE, B&S 5.5 HP Mod 126432-0036-E1
* ENGINE, Honda 5.5 HP Mod GX160K1QX2 Type 553700
1 * ENGINE, B&S 7 HP Mod 120332-0208-E1
42 7073743 1 MUFFLER GUARD, 5HP B&S #391237(Euro) not shown
7074764 1 MUFFLER GUARD, 5.5HP B&S (not shown)
43 7073801 1 SCREW, B&S #94810 (Euro) (not shown)
44 7073802 1 SCREW, B&S #94887 (Euro) (not shown)
45 7074765 1 SCREW, B&S #95259 (Euro) (not shown)
46 7028620 2 SPACER, .340 I.D. x .63 O.D. x .310 Thick
tionItem Qt
Note
Footnotes:
NOTE: * Purchase engine parts from engine manufacture dealer.
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
19
TP 400-5172-9-RT-N
WHEELS, TIRES, RIMS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
20
SERIES 3, 4 & 5
WHEELS, TIRES, RIMS
p
y
Part No Descri
1 7018579 1 ASSEMBLY, Right Wheel (Incl. items 2, 3 & 4)
7018580 1 ASSEMBLY, Left Wheel (Incl. items 2, 3 & 4)
2 7014512 1 RIM
3 7014511 1 TIRE, 13 x 5.00 x 6 (Lug)
4 7012234 1 VALVE, Air (Snap-In)
5 7034162 2 PIN, 5/16” Self-Locking Cotter
6 7029841 2 PIN, 5/16 x 1-11/16” Clevis Was 91677
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
21
TP 400-5172-9-RT-N
DECALS
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
22
SERIES 3, 4 & 5
DECALS
p
y
Part No Descri
1 7071652 DECAL, Ground Breaker (5HP)
7074754 DECAL, Ground Breaker (5-1/2HP)
2 7071655 DECAL, SNAPPER
3 7071654 DECAL, 5HP Engine
4 7071653 DECAL, Dash Panel (5HP)
7074756 DECAL, Dash Panel (5-1/2HP)
5 7015684 DECAL, Warning (Rotating Tines)
6 7043853 DECAL, Safety Operating Instructions
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
23
TP 400-5172-9-RT-N
DECALS (continued)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
24
SERIES 3, 4 & 5
DECALS (continued)
p
y
Part No Descri
7 7046534 DECAL, Warning/Instructions
8 7046919 DECAL, Starting and Warning
9 7043854 DECAL, Warning/Starting Procedure
10 7017682 DECAL, Engine Oil
11 7015408 DECAL, Starting Procedure
12 7046994 DECAL, Caution (Standing on end)
13 7023043 DECAL, Caution (Standing on end)
14 7029470 DECAL, Patent Numbers
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
25
TP 400-5172-9-RT-N
DECALS (continued)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
26
SERIES 3, 4 & 5
DECALS (continued)
p
y
Part No Descri
15 7028700 DECAL, Chute/Read Manual (Euro)
16 7042837 DECAL, OPC Tiller (Euro)
17 7072134 DECAL, Dash Panel (Euro)
18 7073339 DECAL, OPEI Tiller
19 7075378 DECAL, 2003 Year of Manufacture
7074548 DECAL, 2002 Year of Manufacture
20 7029776 DECAL, European Community
21 7047040 DECAL, Chain Case Inspected By
22 7074760 DECAL, Fuel Safety Tiller
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
27
TP 400-5172-9-RT-N
DECALS (continued)
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
28
SERIES 3, 4 & 5
DECALS (continued)
p
y
Part No Descri
23 7074814 DECAL, Warning and Starting Instruction
24 7074815 DECAL, Stop
25 7074816 DECAL, Speed
26 7074817 DECAL, Choke and Fuel
27 7074820 DECAL, Engine On-Off
28 7016134 DECAL, Caution Tag
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
29
TP 400-5172-9-RT-N
CULTIVATOR SHIELD KIT
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
30
SERIES 3, 4 & 5
CULTIVATOR SHIELD KIT
p
y
Part No Descri
7060865 KIT, Cultivator Shield (Incl. items 1 thru 9)
1 7036266 2 CULTIVATOR, Shield
2 7032724 2 BRACKET, Front Latch
3 7038397 1 PIN, Drag Shield
4 7012431 2 PIN, 1/4” Hair
5 7090803 1 BOLT, 1/4-20 x 5/8” Flat Hd. Short Neck Carriage
6 7090911 2 SCREW, 1/4-20 x 1-1/4” Hex Washer Self-Tap
7 7091294 1 WASHER, 1/4” Flat Was 90055
8 7091597 2 PIN, 3/32 x 3/4” Cotter Was 90037
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
31
TP 400-5172-9-RT-N
HILLER - FURROWER KIT
Manual No. 7006047 INTERMEDIATE
TP 400-5172-9-RT-N
32
SERIES 3, 4 & 5
HILLER - FURROWER KIT
p
y
Part No Descri
7060731 KIT, Hiller/Furrower (Incl. items 1 thru 26)
1 7047875 1 BRACKET, Clevis
2 7047858 1 DRAW-BAR
3 7047865 1 STANDARD
4 7032430 1 SKID-SHOE
5 7035072 1 HILLER-FURROWER
6 7036135 1 WING, Left Side Hiller
7 7036134 1 WING, Right Side Hiller
8 7090779 1 BOLT, 1/2-13 x 3-1/2” Sh. Neck. Carriage GR2
9 7090705 1 WASHER, 1/2” Flat
10 7091316 1 NUT, 1/2-13 Hex GR5 or B Was 90258
11 7090316 4 BOLT, 5/16-18 X 3/4” Square Neck Carriage GR5
12 7090188 8 WASHER, 5/16” Flat
13 7091537 4 WING-NUT, 5/16-18 Was 90492
14 7091596 3 PIN, 1/8” Hair Was 13844
15 7013111 3 PIN, 1/2 x 1” Clevis
16 7091540 2 BOLT, 5/16-18 x 1-1/2” Hex Head Cap GR5 Was 90211
17 7091511 2 NUT, 5/16-18 Hex GR5 or B Was 90196
18 7080187 2 WASHER, 5/16” Split Lock
19 7040527 1 BRACKET, Mounting (Front Tine Tiller only)
20 7013460 1 PIN, 3/8 x 1-1/2” Clevis (Front Tine Tiller only)
21 7038217 1 SUPPORT, Clevis
22 7090134 2 SCREW, 3/8-16 x 3/4” Hex Head Cap GR5
23 7090122 1 WASHER, 3/8” Flat
24 7090118 2 WASHER, 3/8” Split Lock
25 7091302 6 NUT, 3/8-16 Hex GR5 or B Was 90130
26 7014206 1 SPACER (not shown)
tionItem Qt
Note
Footnotes:
Manual No. 7006047INTERMEDIATE
SERIES 3, 4 & 5
33
TP 400-5172-9-RT-N
Parts Manual fo
r
INTERMEDIATE
REAR TINE TILLERS
SERIES 3, 4 & 5
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Manual No. 7006047
Revision 9,
2/28/2006
TP 400-5172-9-RT-N
Loading...