Parts Manual fo
r
E
20" SINGLE STAGE SNOW THROWER
COMMERCIAL STEEL FRAM
SERIES 3
MODEL
C3203
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 3,
McDonough, GA, 30253 U.S.A.
9/26/2006
Manual No. 7006014
TP 400-5232-3-SX-N
s
PAGE GROUP
4
6
10
14
16
18
20
Handles, Blade Control
Collector Housing, Belts, Pulleys, Auger
Control Panel, Lower Handle
Discharge Chute
Engine, Covers
Decals
Electric Start
Table Of Content
SERIES 3
Manual No. 700601420" SINGLE STAGE SNOW THROWER
3
TP 400-5232-3-SX-N
Handles, Blade Control
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
4
SERIES 3
Handles, Blade Control
p
y
Part No Descri
1 7032917 1 HANDLE, Upper
2 7014343 2 BUSHING, Auger Control
3 7028309 1 DECAL, Auger Control Instruction
4 7017072 1 CONTROL, Auger
5 7033904 1 CLIP, Auger Control
6 7016367 2 WING-NUT, 1/4-20
7 7015119 1 CLAMP, Cable
8 7028064 1 BRACKET, Lower Handle (Left Side)
9 7091083 2 BOLT, 1/4-20 x 2" Square Neck Carriage, Grade 5
10 7028065 1 BRACKET, Lower Handle (Right Side)
tionItem Qt
Note
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
5
TP 400-5232-3-SX-N
Collector Housing, Belts, Pulleys, Auger
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
6
SERIES 3
Collector Housing, Belts, Pulleys, Auger
p
y
Part No Descri
1 7041605 1 ASSEMBLY, Blower Housing
2 7018796 1 CABLE, Clutch
3 7090372 4 NUT, 1/4-20 Hex Center Lock
4 7091283 8 BOLT, #10-24 x 5/8" Flat Head Carriage
5 7091084 2 SCREW, 1/4-20 x 3/8" Hex Washer Self-Tap Was 90302
6A 7028063 1 BRACE, Engine (Early Production Models)
6B 7034130 1 BRACE, Engine (Later Production Models)
7 7090187 5 WASHER, 5/16 Split Lock
8 7091511 4 NUT, 5/16-18 Hex, Grade 8 or 5 Was 91069
9 7010008 1 KEY, #6 x 5/8" Woodruff
10 7028363 1 PULLEY, Engine
11 7090471 1 SETSCREW, 1/4-20 x 5/16" (Model Year '93 & Earlier)
12 7014098 1 WASHER, Flat (.343 I.D. x 1" O.D.)
13 7090233 1 SCREW, 5/16-24 x 3/4" Hex Head Cap
7061382 1 KIT, Engine Pulley (NLA) (Included item 10, 12,13, & 1
14 7091079 5 NUT, #10-24 Hex Flange Lock
15 7091075 1 SCREW, #10-24 x 5/8" Hex Washer Self-Tap, Grade 5
16 7032345 1 GUIDE, Belt
17 7090981 20 SCREW, #10-32 x 1/4" Slotted Hex Washer Head, Self-Tapping
18 7051506 1 ASSEMBLY, Idler Arm
19 7014722 1 PULLEY, Idler Arm
20 7091575 2 NUT, 5/16-18 hex Center-Lock Was 91067
21 7091076 1 WASHER, 5/16 Flat
22 7014920 1 SPRING, Idler Brake
23 7014919 1 SPACER, Bearing
24 7014608 2 BEARING, Auger
25 7032346 1 RETAINER, Bearing
26 7010935 1 WASHER, 3/4" Flat
27 7018635 1 PULLEY
28 7029604 1 BELT, Auger 32.89 Was 14637
29 7019753 1 COVER, Belt
30 7028427 1 SCRAPER, Blade
31 7028312 1 BLADE, Wear Indicator
7052309 1 ASSEMBLY, Auger (Not shown) (Includes items 32 thru 35)
32 7028067 1 AUGER
33 7014612 2 SHOE, Flite Center 3.5" x 1.56"
34 7091563 28 SCREW, #10-24 x 5/6" Self-Tapping Was 14654
tionItem Qt
Note
item 7)
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
7
TP 400-5232-3-SX-N
Collector Housing, Belts, Pulleys, Auger
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
8
SERIES 3
Collector Housing, Belts, Pulleys, Auger
p
y
Part No Descri
35 7029565 4 SHOE, Flite
7060631 KIT, Flite Shoe 19" (Not shown) (Includes 2 item 33 & 4 item
36 7090584 2 BOLT, 1/4-20 x 1/2" Hex Flange Lock, Grade 5
37 7091545 2 NUT, 1/4-20 Hex Flange Top Lock Was 90477
tionItem Qt
Note
35)Order items 33 & 35 by Kit
Number.
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
9
TP 400-5232-3-SX-N
Control Panel, Lower Handle
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
10
SERIES 3
Control Panel, Lower Handle
p
y
Part No Descri
1 7036165 1 HANDLE, Lower
2 7028201 1 HANDLE, Rope Starter
3 7028202 1 INSERT, Rope Start Handle
4 7091584 4 NUT, 1/4-20 Hex Flange Lock Was 91065
5 7090947 4 BOLT, 1/4-20 x 1 3/8" Square Neck Carriage, Grade 5
6 7038109 1 BRACE, Handle (Right Hand)
7 7090911 2 SCREW, 1/4-20 x 1-1/4" Hex Washer Self-Tap
8 7046473 1 CONTROL, Choke Was 14918
9 7038110 1 BRACE, Handle (Left Hand)
10 7090981 4 SCREW, #10-32 x 1/4" Hex Washer Self-Tap
11 7051560 1 ASSEMBLY, Bracket & Bushing
12 7090896 4 SCREW, 1/4-20 x 1-3/8" Hex Washer Self-Tap
13 7090825 4 SCREW, 1/4-20 x 1-1/4" Hex Head Cap, Grade 5
14 7014645 4 WASHER, 1/4" Curved
15 7090372 5 NUT, 1/4-20 Hex Center Lock Was 91099
16 7014636 1 CAP, Fuel Tank
17 7049732 1 WELDMENT, Handle/Panel
18 7014638 1 PRIMER, Fuel
19 7028305 1 DECAL, Model
20 7091079 1 NUT, #10-24 Hex Flange Lock
21 7028062 1 COVER, Access Hole
22 7028308 1 DECAL, Control Panel
23 7012485 4 RETAINER, 1/4" Bolt
24 7032943 1 BAFFLE, Left Hand
25 7014639 1 HOSE, Primer
26 7032366 1 AXLE
27 7029900 2 CLAMP, Fuel Line Was 12222
28 7032365 1 LINE, Fuel
29 7019736 1 TANK, Fuel
30 7091149 4 WASHER, 3/8" Flat
31 7027446 2 WHEEL
32 7091135 2 NUT, 3/8 Push
33 7091081 4 SCREW, 1/4-15 x 3/4" Hex Washer Head, Self-Tapping
34 7017817 1 SWITCH, Ignition (2 pole) Was 15211 (Includes items 35 &
35 7091546 1 WASHER, 5/8 Internal Tooth Lock Was 90880
36 7016132 1 SPACER
37 7012685 1 NUT, 5/8-32 Hex (Special)
tionItem Qt
Note
37)
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
11
TP 400-5232-3-SX-N
Control Panel, Lower Handle
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
12
SERIES 3
Control Panel, Lower Handle
p
y
Part No Descri
38 7023506 1 BEZEL
39 7073406 1 KEY, Ignition Was 23507
40 7073406 1 KEY, Switch (With Cover) Was 23504
tionItem Qt
Note
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
13
TP 400-5232-3-SX-N
Discharge Chute
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
14
SERIES 3
Discharge Chute
p
y
Part No Descri
1 7053488 1 ASSEMBLY, Chute & Discharge Decal (Includes items 2, 3, & 4)
2 7028345 1 CHUTE (Replaced by 7053488) Was 28345 (Includes Decal,
3 7028346 1 PIN, Wire Hinge
4 7028344 1 DEFLECTOR, Discharge
5 7091076 3 WASHER, 5/16 Flat
6 7016368 1 WING-NUT, 5/16-18
7 7027448 1 DECAL, DANGER
8 7090316 1 BOLT, 5/16-18 x 1" Carriage Was 91097
9 7091021 1 SCREW, 5/16-24 x 1" Hex Head Cap
10 7091606 2 NUT, 5/16-24 Hex Center Lock Was 91074
11 7091075 6 SCREW, #10-24 x 5/8" Slotted Hex Head, Self-Tapping
12 7014915 3 RETAINER, Chute to Housing
13 7016330 1 SPRING, Release Rod
14 7032919 1 STOP, Handle
15 7091597 1 COTTER-PIN, 3/32 x 3/4" Was 91082
16 7016329 1 ROD, Release
tionItem Qt
Note
Deflector, & Pin)
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
15
TP 400-5232-3-SX-N
Engine, Covers
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
16
SERIES 3
Engine, Covers
p
y
Part No Descri
1 7027401 1 COVER, Top
2 7019295 1 DECAL, SNAPPER Was 28307
3 7091079 7 NUT, #10-24 Hex Flange Lock
4 1 * ENGINE, Tecumseh Model HSK 600, Spec. No. 1696S (2-
Cycle)
5 7090676 1 BOLT, 1/4-20 x 3/8" Hex Flange Lock
6 7091601 1 NUT, 5/16-18 Hex Flange Lock Was 90585
7 7019362 2 CLIP, "S"
8 7019980 1 COVER, Bottom
9 7090981 10 SCREW, #10-32 x 1/4" Self-Tapping
10 7028306 1 DECAL, Commercial
11 7090913 2 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx)
12 7028066 1 BRACE
13 7019350 1 SEAL, Foam
tionItem Qt
Note
Was TEC # HSK600-1696T
Footnotes:
Note: * Purchase engine parts from engine manufacturer dealer.
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
17
TP 400-5232-3-SX-N
Decals
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
18
SERIES 3
Decals
p
y
Part No Descri
1 7019295 1 DECAL, SNAPPER Was 28307
2 7027448 1 DECAL, DANGER
3 7028306 1 DECAL, Commercial
4 7028309 1 DECAL, Auger Control
5 7028305 1 DECAL, Model C3203
6 7028308 1 DECAL, Control Panel
tionItem Qt
Note
Footnotes:
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
19
TP 400-5232-3-SX-N
Electric Start
Manual No. 7006014 20" SINGLE STAGE SNOW THROWER
TP 400-5232-3-SX-N
20
SERIES 3
Electric Start
p
y
Part No Descri
7060608 1 KIT, Electric Start (Tec. Part # 1133-106 or 7) (Tecumseh Engines)
1 7090866 2 SCREW, #10-24 x 1-3/4" Phillips Pan Head
2 7090623 2 NUT, #10-24 Hex Lock
3 7090010 4 WASHER, #10 Flat
7015368 1 CORD, 110 V (Not shown) (Tec. Part # 1A174-17 or 5277-02) Was 29747
tionItem Qt
Note
Footnotes:
Note: * Purchase engine parts from engine manufacturer dealer.
Manual No. 700601420" SINGLE STAGE SNOW THROWER
SERIES 3
21
TP 400-5232-3-SX-N
Parts Manual fo
r
20" SINGLE STAGE SNOW THROWER
COMMERCIAL STEEL FRAME
SERIES 3
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Manual No. 7006014
Revision 3,
9/26/2006
TP 400-5232-3-SX-N
Loading...