![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg1.png)
Safety Instructions & Operator's Manual for
TWO STAGE
LARGE FRAME
SNOW THROWER
SERIES 6
MODELS
8246 9266
9266E 11306
MODEL NUMBER EXPLANATION
I
9 1261 6 I E I
ENGINE HP
AUGER WIDTH
8 - 8.0 Engine HP (Engine Horse Power
9 - 9.0 Engine HP (Engine Horse Power)
11 - 11.0 Engine HP (Engine Horse Power)
Thank you for buying a SNAPPER Product! Before operating your Snow Thrower, read this manual carefully and pay
particular attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Pages 2 & 3. Remember that all power
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance
with the operating instructions and common sense.
24 - 24" Auger Width
26 - 26" Auger Width
30 - 30" Auger Width
6 - Series Designation
E - Electric Start
ELECTRIC START
SERIES DESIGNATION
SNAPPERMcDonough,GA., 30253 U.S.A.
COPYRIGHT © 2003
SNAPPER PRODUCTS INC.
ALL RIGHTS RESERVED
MANUAL No. 7-5394 (I.R. 3/3/03)
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg2.png)
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury
and damage! Failure to comply with the following instructions may result in serious injury to the operator or
other persons. The owner of the snow thrower must understand these instructions and, furthermore, must
allow only persons who understand these instructions to operate snow thrower. Each person operating the
snow thrower must be of sound mind and body and must not be under the influence of any substance which
might impair vision, dexterity, or judgment. If you have any questions pertaining to your snow thrower which
your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER,
McDonough, Georgia 30253. Phone: 800/935-2967.
PROTECTION FOR CHILDREN
Tragic accidents can occur if the operator is not alert
to the presence of children. Children are often
attracted to the machine and the snow removal
activity. Never assume that the children will remain
where you last saw them.
1. DO NOT allow children in the area when snow
thrower is being operated.
2. DO NOT allow pre-teenage children to operate
snow thrower.
3. ALLOW only responsible adults and teenagers
with mature judgment to operate the machine
and then only after being thoroughly instructed
and under the close supervision of an
experienced adult operator.
4. Keep the area clear of all persons, particularly
small children and pets.
5. Know how to STOP the snow thrower and
disengage the controls quickly.
PREPARATION
1. Warn everyone in advance to stay clear of area.
Keep especially watchful for children and pets
darting into area while operating.
2. Read, understand, and follow instructions and
warnings in this manual and on the machine.
Know the controls and the proper use of the
snow thrower before starting.
3. Data indicates that operators, age 60 and above,
are involved in a large percentage of snow
thrower-related injuries. These operators should
evaluate their ability to operate the snow thrower
safely enough to protect themselves and others
from serious injury.
4. Disengage all clutches and shift into neutral
before starting the engine (motor).
5. Wear adequate winter clothing including boots
which will give you maximum footing on slippery
surfaces. Exercise CAUTION to avoid slipping or
falling.
6. Before the first snow fall, check the area to be
cleared and remove all objects such as
doormats, sticks, toys, wires, rocks, etc., which
could be hurled or jam the snow thrower
PREPARATION
(Continued From Previous Column)
7. Survey the area to be cleared beforehand and
plan where snow is to be blown. Be prepared to
release auger/impeller clutch or to change
discharge chute direction quickly to discharge
away from windows, cars, buildings and
doorways to avoid property damage or personal
injury from hurled objects.
8. Use only approved extension cords and
receptacles in good condition and with sufficient
capacity to carry the current to the machine if
equipped with electric starting motors.
9. Handle fuel with extra care. Fuels are flammable
and vapors are explosive. Store only in an
approved fuel container. Never remove fuel cap
or add fuel with the engine running. Add fuel
outdoors only with the engine stopped and cool.
Clean spilled fuel and oil from machine. DO NOT
smoke. DO NOT run engine indoors.
OPERATIONAL PRECAUTIONS
1. Before starting, make visual check to make sure
auger/impeller housing is clear and all guards
and shields are in place and tight.
2. DO NOT operate machine without proper guards
shields, deflectors, or other safety protective
devices in place and functioning properly.
3. Should the auger/impeller become clogged,
release the auger/impeller clutch control and, as
an additional precaution, STOP the engine
before attempting to unclog the auger/impeller or
discharge chute.
4. DO NOT attempt to unclog the auger/impeller or
discharge chute by reaching in with your hands.
Use a long stick or similar implement to unclog.
5. DO NOT attempt to unclog the auger/impeller or
discharge chute with the engine running. STOP
engine and remove key.
6. STOP engine (motor) and remove key before
leaving the operator position for any reason.
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg3.png)
IMPORTANT SAFETY INSTRUCTIONS
OPERATIONAL PRECAUTIONS
(Continued From Previous Page)
7. DO NOT put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
8. Start engine only where exhaust fumes will be safely
dissipated. Allow a brief warm-up period, and
practice operation of controls outside before putting
the machine to work.
9. After striking a foreign object, STOP the engine
(motor), remove the key, and remove the wire from
spark plug. Thoroughly inspect the snow thrower for
any damage, and repair the damage before restarting
and operating the snow thrower.
10. STOP the engine if the machine starts to vibrate
excessively as this normally indicates mechanical
problems. Remove the key and disconnect the spark
plug wire to prevent unintentional starting before
servicing or repairing the machine.
11. DO NOT clear snow across the face of slopes.
Exercise extreme CAUTION when changing direction
on slopes. DO NOT attempt to clear steep slopes.
12. DO NOT leave machine unattended with the engine
running. STOP engine and remove key to prevent
unauthorized operation.
13. Release clutch control and make sure auger/impeller
has STOPPED before adjusting deflector, or placing
hands near auger/impeller.
14. DO NOT use snow thrower on surfaces above
ground level, such as, a roof of a building.
15. Exercise extreme CAUTION when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or traffic.
16. DO NOT overload the machine capacity by
attempting to clear snow at too fast a rate.
17. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when backing.
18. Disengage power to the auger/impeller when snow
thrower is transported or not in use.
19. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as
wheels weights, counterweights, cabs and the like).
20. Never operate the snow thrower without good
visibility or light. Always be sure of your footing, and
keep a firm hold on the handles. Walk; never run.
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline isextremely
flammable and the vapors are explosive
1. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
2. Use only an approved fuel container.
3. DO NOT remove fuel cap or add fuel with the engine
running. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as on a water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always place
the containers on the ground away from the vehicle
before filling.
7. Remove gas-powered equipment from the vehicle or
trailer and refuel it on the ground. If this is not
possible, then refuel equipment using a portable
container, rather than a gasoline dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed
vehicles or trailers.
9. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. DO NOT use a nozzle lock-open device
10. If fuel is spilled on clothing, change clothing
immediately.
11. Never overfill a fuel tank. Replace fuel cap and
tighten securely.
MAINTENANCE AND STORAGE
1. DO NOT store machine or fuel container inside
where fumes may reach an open flame, spark, or
pilot light as ina water heater, furnace, clothes dryer
or other gas appliance. Allow engine to cool before
storing machine in an enclosure. Store fuel container
out of reach of children in a well ventilated,
unoccupied building.
2. Keep machine and engine free of excess oil, grease
and spilled fuel to reduce fire hazard.
3. When draining fuel tank, drain fuel into an approved
container outdoors and away from open flame.
4. Inspect all bolts, nuts and screws frequently and
keep properly tightened.
5. Use only recommended shear bolts (if equipped) to
prevent possible damage to machine.
6. Service engine and make adjustments only when
engine is stopped. Remove key, remove wire from
spark plug, secure wire away from plug, and
disconnect cord from electric starting motors to
prevent accidental starting.
7. DO NOT change engine governor speed settings or
overspeed engine.
8. DO NOT test for spark by grounding the spark plug
next to spark plug hole. Spark from the plug could
ignite gas exiting engine.
9. Have machine serviced by an authorized SNAPPER
dealer at least once a year and have the dealer install
any new safety devices.
10. Use only genuine SNAPPER replacement parts to
assure that original standards are maintained.
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg4.png)
TABLE OF CONTENTS
SECTION 1 - IMPORTANT SAFETY INSTRUCTIONS .......................... 2-3
TABLE OF CONTENTS ............................................................................ 4
SECTION 2 - OPERATING INSTRUCTIONS ....................................... 5-10
Introduction ................................................................................................................. 5
Pre-start Checklist ................................................................................................... 6-7
Starting & Stopping Engine (Recoil Start Models) ............................................. 7-10
Starting & Stopping Engine (Electric Start Models) .......................................... 9-10
Starting & Stopping Auger/Impeller ..................................................................... 8-10
Starting & Stopping Wheel Drive ......................................................................... 8-10
Free Wheel Machine ................................................................................................. 10
SECTION 3 - MAINTENANCE INSTRUCTIONS ................................ 11-12
Checking Auger Drive Belt ...................................................................................... 11
Checking Wheel Drive Belt ...................................................................................... 11
Lubricate Gear Case ................................................................................................. 11
Lubricate Auger & Bearing ...................................................................................... 11
General Lubrication .................................................................................................. 11
Annually (End of Season) ........................................................................................ 12
Changing Engine Oil .......................................................................................... 12
Changing Spark Plug......................................................................................... 12
Storage Procedure ................................................................................................... 12
Maintenance and Service Parts .............................................................................. 12
SECTION 4 - ADJUSTMENTS AND REPAIR .................................... 13-18
Auger/Impeller & Wheel Drive Belt Adjustment ................................................ 13-14
Auger/Impeller & Wheel Drive Belt Replacement ............................................. 14-15
Skid Shoe Adjustment ............................................................................................. 16
Single Handle Control Adjustment ......................................................................... 17
Auger Shear Bolt Replacement ............................................................................... 18
Chute Crank Adjustment ......................................................................................... 18
Rubber Drive Tire Replacement .............................................................................. 18
TROUBLESHOOTING ............................................................................ 19
SERVICE SCHEDULE ............................................................................ 19
WARRANTY AND PRODUCT REGISTRATION ................................ 20-21
IMPORTANT
The figures and illustrations in this manual are provided for reference only and
may differ from your specific model. Contact your Snapper dealer if you have
questions.
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg5.png)
Section 2 - OPERATING INSTRUCTIONS
1.1 INTRODUCTION
Before starting machine, visually check location of all operational controls and identify major parts discussed in
Operator's Manual.
REMOTE DEFLECTOR
HIGH SPEED IMPELLER
CONTROL (26" & 30" MODELS)
SPEED CONTROL LEVER
DISCHARGE CHUTE
_CONTROL
IMPELLER HOUSING
DISCHARGE_
DEFLECTOR
CAP
FUEL TANK
BLOWERCLUTCH_
CONTROL LEVER /
HEAD LIGHT
(26"&30"MODELS)
--TRACTION CLUTCH
CONTROL LEVER
PANEL
DISCHARGE CHUTE
WHEEL RETAINING
PINS
TIRES
12-16 PSI W/O CHAINS.
16-20 PSI WITH CHAINS.
BLOWER
HOUSING
COLLECTO
R AUGERS
(REPLACEABLE)
GEAR BOX
SKID SHOES
IMPELLER
(ROTATES @ APPROX.
1100 RPM DURING OPERATION)
FIGURE 1.1
NOMENCLATURE
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg6.png)
Section 2 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
Make the following checks and perform the service
required before each start-up.
2.1.1. Check engine oil and add oil as needed to
bring level up to the FULL mark. Refer to engine
owner's manual for oil specifications.
2.1.2. Check guards, chutes, deflectors and covers
to make sure all are in place and securely
tightened.
2.1.3. Check auger/impeller control and wheel drive
control to insure cables are connected and both
levers operate freely. See Figure 2.1.
IMPORTANT: On 26" & 30" Auger models only. Standing in
the operator's position, the left handle bar lever is for wheel
drive engagement and disengagement. The right handle bar
lever is for auger/impeller engagement and disengagement.
Hold both levers down to handle bar for engagement and
release levers for disengagement. When both levers are
pressed down to the handle bar at the same time, the
operator can release the right hand lever and the right lever
will remain engaged as long as the left hand lever is held
down to handle bar. Release the left hand lever and both
levers will disengage.
PRESS BOTH LEVERS --'1
RELEASE BLOWER
CLUTCH LEVER;
CONTINUE HOLDING
WHEEL DRIVE
WARNING
Use approved fuel container. DO NOT smoke near
open fuel container. DO NOT fill fuel tank indoors or
when engine is running. Allow engine to cool for at
least ten minutes before refilling. Wipe off any
spilled fuel before starting engine. DO NOT run
engine indoors.
2.1.6. Add fuel to tank after pushing the machine
outside where fumes can safely dissipate. Make sure
cap is tightened after refueling. Wipe up any spilled
fuel on machine and surrounding area. Refer to
Engine Owners Manual for specifications.
2.1.7. Check auger/impeller housing and discharge
chute, both must be free of all obstructions. Clean
engine of any accumulation of spilled fuel, dirt, etc.
WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord could
cause a shock or fire. Thoroughly inspect electrical
extension cord before using machine. If cord is
damaged, do not use and do not operate machine.
Replace damaged cord immediately. Contact your
Snapper service dealer for assistance. To reduce the
risk of electric shock, use only with an extension
cord intended for outdoor use having a cord type:
SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A or
SJTOW-A.
WHEEL
DRIVE
CONTROL
FIGURE 2.1
2.1.4. Check chute operation. Rotate chute crank to
insure smooth rotation throughout its range. See
Section 4.1.6. for worm gear adjustment.
2.1.5. Check tires and add or release air as needed
to bring air pressure to 12 psi without tire chains. Air
pressure with tire chains should be 16 psi.
IMPORTANT: Electric Start Kit optional
accessory on some models.
2.1.8. Check and make sure extension cord is in
good condition. Extension cord should not have any
broken insulation or exposed wires. Use an
extension cord that is heavy enough to carry the
correct amount of current to the machine. See
Figure 2.2 for correct size to use depending on cord
length and nameplate ampere rating. If in doubt,
use the next heavier gauge cord.
MINIMUM GAUGE FOR CORD SETS
120 or 230 Volt Total Length of Cord in Feet
Rating-Amps 25 ft. I 50 ft. I 100 ft. I 150 ft.
More Not More ,7,.,,,.,A.W._'_.
Than Than
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not
FIGURE 2.2
Recommended
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg7.png)
Section 2 - OPERATING INSTRUCTIONS
2.1
PRE-START CHECK LIST
2.1.9. Check the AC electrical outlet that will be
used and make sure it is a polarized outlet. The
machine has a polarized plug (one blade of plug is
wider than the other) that will accept a polarized
extension cord. The extension cord will fit into a
polarized outlet (receptacle) only one way. If plug
does not fit fully into your outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to
install a proper polarized outlet. DO NOT modify or
change this polarized plug in any way.
2.2
STARTING, OPERATION & STOPPING
(RECOIL START MODELS)
MOVE CHOKE TO THE
"ON" POSITION
PUSH PRIMER
THREE TIMES
2.2.1. ENGINE
1. Turn fuel shut off valve to the "ON" position. See
Figure 2.3.
\
, TURN VALVE TO
"ON" POSITION
MOVE ENGINE
F--SPEEDCONTROL
"" / TO FAST
I
INSERT
KEY
FIGURE 2.4
6. Pull rope start handle to crank engine.
7. After engine starts, move the choke control to
the no choke, "OFF" position. Allow a brief warm-up
until engine runs smooth.
(Continued on Next Page)
FIGURE 2.3
2. Insert key into ignition switch. See Figure 2.4.
3. Move choke control to the choke, "ON" position.
See Figure 2.4.
4. Move engine speed control to the "FAST"
position. See Figure 2.4.
5. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine. See Figure 2.4.
IMPORTANT: Stop the auger/impeller and wheel drive
by releasing the auger/impeller and wheel drive control
levers. Stop the engine by moving the engine speed
control to stop or removing the key from the switch.
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg8.png)
Section 2 - OPERATING INSTRUCTIONS
2.2
STARTING, OPERATION & STOPPING
(RECOIL START MODELS)
(Continued From Previous Page)
AUGE_IMPELLER
CONTROL
2.2.2. PROPELLING SNOW THROWER
IMPORTANT: This snow thrower has six forward
speeds and one reverse speed.
1. Move ground speed control to the desired
speed position. See Figure 2.5.
2. Proceed to Section 2.2.4. to engage wheel
drive.
SPEED CONTROL
DEFLECTOR CONTROL
CHUTE
CRANK
O
FIGURE 2.5
oDLRIVE
o
FIGURE 2.6
2.2.5. DISCHARGE CHUTE and DEFLECTOR
ADJUSTMENT
1. Release auger/impeller control and wheel drive
control levers to allow auger/impeller and ground
speed to come to a complete stop.
2. Position the deflector in the desired location using
deflector handle located on control panel. Rotate
deflector handle counter clockwise to unlock. Push
handle to raise or pull handle to lower the deflector.
Rotate deflector handle clockwise to lock into position.
3. Rotate chute crank to position discharge chute in
desired direction. Refer to Figure 2.5.
Objects can be thrown by the snow thrower while it
is in operation. Thrown objects could cause serious
injury to the operator or bystanders. Always wear
safety goggles or other suitable eye protection.
Keep people and pets away from area. Release
auger/impeller clutch and wheel drive controls and
make sure auger/impeller and wheel drive have
STOPPED before rotating discharge chute, or
adjusting deflector. DO NOT place hands near
auger/impeller while engine is running
2.2.3. ENGAGING AUGER
1. Move auger/impeller control lever against
handle to engage auger/impeller. See Figure 2.6.
2.2.4. ENGAGING WHEEL DRIVE
1. Move wheel drive control lever against handle
to engage wheel drive. Ground speed can be
changed while the machine is in operation by
changing position of the ground speed control.
IMPORTANT: This snow thrower has six forward
speeds and one reverse speed, See Figure 2,6,
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bg9.png)
Section 2 - OPERATING INSTRUCTIONS
2.2 STARTING, OPERATION & STOPPING
(RECOIL START MODELS)
2.2.6. STOPPING - ENGINE, AUGER & WHEEL
DRIVE
Stop the auger/impeller and wheel drive by
releasing the auger/impeller and wheel drive
control levers. Stop the engine by moving the
engine speed control to the stop position or
removing the key from the switch. Always remove
key from key switch before leaving machine
unattended. See Figure 2.7.
MOVE CONTROL TO
"STOP"
_REMOVE
KEY
2.2.7. ENGINE
1. Turn fuel shut off valve to the "ON" position.
Refer to Figure 2.3.
2. Insert key into ignition switch. See Figure 2.8.
3. Connect the power cord to the starter switch
box on the engine, then plug the other end into 120
volt AC receptacle.
4. Move choke control to the choke, "ON" position.
See Figure 2.8.
IMPORTANT: Stop the auger/impeller and wheel drive
by releasing the auger/impeller and wheel drive control
levers. Stop the engine by moving the engine speed
control to the stop position or removing the key from the
switch.
5. Move engine speed control to the "FAST"
position. See Figure 2.8.
6. Push primer button three times to start a cold
engine. NOTE: Do not use primer button to start
warm engine.
7. Push the electric starter button. DO NOT hold
button for more than 20 seconds to avoid
damaging the starting motor. See Figure 2.8.
8. After engine starts, move the choke control to
the no choke "OFF" position. Allow a brief warm-up
until engine runs smooth.
9. Disconnect power cord from AC receptacle.
Disconnect power cord from machine and remove
cord from area where machine will be in operation.
START
BUTTON _
PLUG INTO
HERE
FIGURE 2.7
2.2
STARTING, OPERATION & STOPPING
(ELECTRIC START MODELS)
WARNING
DO NOT use an electrical extension cord that is
damaged. A damaged electrical extension cord
could cause a shock or fire. Thoroughly inspect
electrical extension cord before using machine. If
cord is damaged, do not use and do not operate
machine. Replace damaged cord immediately.
Contact your Snapper service dealer for assistance.
To reduce the risk of electric shock, use only with
an extension cord intended for outdoor use having
a cord type: SW-A, SOW-A, STW-A, STOW-A, SJW-
A, SJTW-A or SJTOW-A.
!
MOVE
CHOKE TO
THE"ON"
POSITION
PUSH PRIMER
THREE TIMES
MOVE ENGINE
SPEED CONTROL
TO"FAST"
INSERT KEY
FIGURE 2.8
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bga.png)
Section 2 - OPERATING INSTRUCTIONS
2.2
STARTING, OPERATION & STOPPING
(ELECTRIC START MODELS)
(Continue From Previous Page)
WARNING
Objects can be thrown by the snow thrower while it
is in operation. Thrown objects could cause serious
injury to the operator or bystanders. Always wear
safety goggles or other suitable eye protection.
Keep people and pets away from area.
2.2.8. ENGAGING AUGER
1. Pull auger/impeller control lever against handle
to engage auger/impeller. Refer to Figure 2.6.
2.2.9. ENGAGING WHEEL DRIVE
1. Move wheel drive control lever against handle
to engage wheel drive. Ground speed can be
adjusted while the machine is moving by changing
position of the ground speed control. Machine has
six forward speeds and one reverse. Refer to
Figure 2.5.
2.2.12. FREE WHEEL MACHINE
Snow Thrower can be transported without engine
running and transmission drag.
1. Remove hair pins and clevis pins from both
wheel axles. Remove wheels from axle. Apply a
liberal amount of axle grease to the axle to allow
the wheel to rotate freely.
2. Slide wheel inward toward main case.
3. Reinstall clevis pins and hair pins into outer
holes to prevent wheel from sliding off of the end
of axle. Wheels will rotate freely on axle.
IMPORTANT: If engine is started the wheel drive
will not operate unless wheels and axle are
reconnected. Reinstall clevis pins and hair pins
into holes in the hubs of the wheels and through
axle. See Figure 2.9.
OUTSIDE
INSIDE "DRIVE"
HOLE
EWHEEL)
WARNING
Release auger/impeller clutch control and make sure
auger/impeller has STOPPED before rotating
discharge chute, or adjusting deflector. DO NOT place
hands near auger/impeller while engine is running.
2.2.10. DISCHARGE CHUTE and DEFLECTOR
ADJUSTMENT
1. Release auger/impeller control and wheel drive
control levers to allow auger/impeller and ground
speed to come to a complete stop.
2. Position the deflector to the desired location using
deflector handle located on control panel. Rotate
deflector handle counter clockwise to unlock. Push
handle to raise or pull handle to lower the deflector.
Rotate deflector handle clockwise to lock into position.
3. Rotate chute crank to position discharge chute in
desired direction. Refer to Figure 2.5.
2.2.11. STOPPING - ENGINE, AUGER & WHEEL
DRIVE
Stop the auger/impeller and wheel drive by
releasing the auger/impeller and wheel drive
control levers. Stop the engine by moving the
engine speed control to the stop position or
removing the key from the switch. Always remove
key from key switch before leaving machine
unattended. Refer to Figure 2.7.
CLEVIS
PIN
FIGURE 2.9
DRIVE
WHEEL
10
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bgb.png)
Section 3 - MAINTENANCE
3.1 INTRODUCTION
To retain the quality of the snow thrower, use only
genuine SNAPPER replacement parts. Contact a
local SNAPPER dealer for parts and service
assistance. For the correct part or information for a
particular snow thrower, always mention model and
serial number.
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.1 CHECK AUGER DRIVE BELT
1. Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. Replace
belt before operating snow thrower. See Figure 3.1
AUGER BELT
3.3 GENERAL LUBRICATION
Lubricate machine as instructed before and after
operation each season.
3.3.1. GEAR CASE, AUGER SHAFT and AUGER
BEARING LUBRICATION
1. Before each season of operation, apply two
shots of grease from a grease gun into gear case.
Snapper suggests using Benalene 900. The grease
plug for the gear case is located in front of the gear
case. See Figure 3.3.
2. Before each season of operation, apply two
shots of grease from a grease gun into each auger
bearing. Snapper suggests using Benalene 900.
The grease fitting for the auger bearing is located
on each end of the auger. See Figure 3.3.
3. Before each season of operation, apply two
shots of general purpose grease from a grease gun
into the auger shaft. The grease fitting for the auger
shaft is located in the middle of each auger.
Remove shear bolts and rotate auger to distribute
grease evenly around shaft. Reinstall shear bolts
and nuts. Tighten to 5 to 10 ft. lb. of torque. See
Figure 3.3.
FIGURE 3.1
3.2.2 CHECK WHEEL DRIVE BELT
1. Visually check wheel drive belt for cracking,
fraying, severed or belt strands exposed. Replace
belt before operating snow thrower. See Figure 3.2.
DRIVE
BELT
\
SHEAR BOLT
FITTING
BEARING GREASE
0
GREASE
PLUG
FIGURE 3.3
3.3.2. GENERAL LUBRICATION
After each season of operation, spread a small
amount of grease on: The axle shafts for easy
wheel removal. The discharge chute and mounting
flange retainers for smooth rotation.
FIGURE 3.2
11
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bgc.png)
Section 3 - MAINTENANCE
3.4
ANNUALLY (END OF EACH SEASON)
Perform all maintenance as
maintenance schedule.
3.4.1. Engine
Refer to engine
instructions.
3.4.2. Spark Plug
Refer to engine
instructions.
3.5 STORAGE PROCEDURE
Refer to the Engine Owner's Manual for directions
regarding engine storage preparations. Prepare the snow
thrower for "end of season" storage as follows:
1. Drain fuel from fuel tank and let engine run until
all fuel is out of the carburetor.
2. Disconnect and remove the spark plug wire
away from spark plug before any other
preparations are made!
3. Tape all openings closed to prevent spraying
water into exhaust or air intakes during washing.
4. Tilt snow thrower up on its wheels and
thoroughly clean the underside of the
auger/impeller.
5. Lubricate all exposed metal with a light coating
of oil to prevent corrosion.
6. Store the machine in a shed or other dry area,
protected from weather.
owner's manual for service
owner's manual for service
described in the
3.6 MAINTENANCE and SERVICE PARTS
MAINTENANCE and SERVICE PARTS
Auger Drive Belt (Briggs Engines) 1-3937
Auger Drive Belt (Tecumseh Engines) 1-3939
Wheel Drive Belt (Briggs Engines) 1-3936
Wheel Drive Belt (Tecumseh Engines) 2-9101
Scraper Blade (24" Width Auger) 3-6122
Scraper Blade (26" Width Auger) 3-9770
Scraper Blade (30" Width Auger) 3-6006
Rubber Drive Tire 1-0765
Shear Bolts - 5/16-18 x 1-7/8" 9-1550
Hex Nuts - 5/16-18 9-1298
Parts Manual for Large Frame Snow Throwers - Series 6 #06069
Models: 8246, 9266, 9266E, 11306
12
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bgd.png)
Section 4 - REPAIR & ADJUSTMENTS
WARNING
DO NOT attempt any adjustments, maintenance,
service, or repairs, with engine running. Stop auger.
Stop engine. Remove key. Disconnect spark plug
wire and secure wire away from spark plug.
4.1 AUGER/IMPELLER and WHEEL DRIVE BELT
ADJUSTMENT/REPLACEMENT
When operating machine release the auger/impeller
clutch control. The auger/impeller should come to a
complete stop in 5 seconds. If the auger/impeller does
not come to a complete stop in the required time,
check and adjust belt tension. Inspect belts frequently
for signs of excessive wear. Observe drive belts for
slippage due to wear when operating machine. If
slippage does occur, adjust/replace as follows.
4.1.1. AUGER and WHEEL DRIVE CABLE
ADJUSTMENT
1. Measure control cable extension from a relaxed
position to full extended position. Move control lever
against handle. Measure the overall length of the
spring. The length of the cable spring should
increase by 318" when the clutch control lever is
depressed. See Figure 4.1.
4.1.2. AUGER BELT IDLER PULLEY
ADJUSTMENT
NOTE: To adjust the idler pulley and properly tension
the auger belt, the auger control cable adjustment
must first be loosened as described in the following
step. Cable adjustment must be checked after
completing the idler pulley adjustment.
1. Loosen jam nut at the end of cable. Hold
threaded end of cable and then turn metal housing
of cable counter clockwise until threaded portion of
cable is extracted from metal housing. Reinstall 1/2"
of the threaded portion of cable back into metal
housing. Retighten jam nut.
2. Remove belt cover. See Figure 4.2.
REMOVE
BELT
COVER
\
CABLE MUST BE
SLACK WHEN '_',_ _ I _'
CLUTCH HANDLE IS_,_\ "_
RELEASED _, ....
F' CABLE _'_ A
"_ /CONNECTOR
/--JAM fCABLE
SPRING
............................................ , O HOOLO
o-,%-,<?..>_
°v_'4f__"_.,_ STRETCH 3/8" WHEN
,q,.7
_,_j LEVER IS DEPRESSED
FIGURE 4.1
2. Adjust control cable by loosening jam nut at the
upper end of cable. Hold threaded end of cable and
then turn cable clockwise or counter clockwise until
correct extension is achieved. Retighten jam nut.
IMPORTANT: DO NOT over tighten the control cables.
The cables must have slack for the auger/impeller brake
to function properly and for the wheel drive to de-clutch
properly. If the auger control cannot be properly
adjusted, belt adjustment and/or replacement will be
required. Refer to Section "Auger Belt Idler Pulley
Adjustment". If the wheel drive control cannot be properly
adjusted, the rubber drive tire will require replacement.
Refer to Section "Rubber Drive Tire Replacement".
1=
FIGURE 4.2
3. Loosen nut and bolt that secures the idler pulley.
Move idler toward belt for more tension or away
from belt for less tension. See Figure 4.3. Retighten
bolt and nut securely.
BLOWER BELT GUIDE
(SHOULD CLEAR
BELT & PULLEY 1/1G"
IDLER
PULLEY
NUT
LOOSEN
FIGURE 4.3
TO 1/8")
BLOWER IDLER
ARM
TIGHTEN
BLOWER IDLER
RETURN SPRING
13
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bge.png)
Section 4 - REPAIR & ADJUSTMENTS
DO NOT attempt any adjustments, maintenance,
service, or repairs, with engine running. Stop auger.
Stop engine. Remove key. Disconnect spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank.
Allow engine to run, outdoors where fumes can be
safely dissipated, until all fuel is removed from
carburetor.
4.1.2. AUGER DRIVE BELT ADJUSTMENT
(IDLER PULLEY ADJUSTMENT)
(Continued From Previous Page)
4. Recheck cable for proper extension (3/8").
5. Reinstall belt cover.
4.1.3. AUGER DRIVE BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or exposed belt strands.
1. Remove belt cover. See Figure 4.2.
2. Remove discharge chute.
3. Unhook both idler springs.
4. Loosen auger/impeller belt guide. See Figure 4.4.
IMPORTANT: Wheel drive belt will have to be removed
from around engine drive pulley and engine shaft to
install auger drive belt.
5. Remove auger drive belt from around engine
pulley. See Figure 4.4.
/ -.'/
BELT GUID_
6. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.5.
SELF-TAPPING "_\
SCREWS
REMOVE
COVER
FIGURE 4.5
7. Remove auger drive belt from drive disc pulley.
Route auger belt through drive system in between
rubber drive tire and drive disc.
8. Route new auger drive belt through drive
system. NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position
it around auger pulley.
9. Reinstall wheel drive belt onto engine wheel
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
10. Route auger drive belt around engine auger
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
11. Position belt guide against auger drive belt and
tighten securely.
12. Reinstall both idler springs.
13. Reinstall discharge chute, belt cover and drive
system cover. Tighten screws securely.
14. Adjust idler for proper belt tension and control
cable for proper spring extension. Refer to Section
"Auger Belt Idler Pulley Adjustment".
FIGURE 4.4
14
![](/html/8c/8cfa/8cfa1452824e539bac70e3d64684852213085fe40f29048a80eeed34f4f1d981/bgf.png)
Section 4 - REPAIR & ADJUSTMENTS
WARNING
DO NOT attempt any adjustments, maintenance,
service, or repairs, with engine running. Stop auger.
Stop engine. Remove key. Disconnect spark plug
wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank. Allow
engine to run, outdoors where fumes can be safely
dissipated, until all fuel is removed from carburetor.
4.1.4. WHEEL DRIVE BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or exposed belt strands.
1. Remove belt cover. See Figure 4.2.
2. Remove discharge chute.
3. Unhook both idler springs.
4. Loosen auger/impeller belt guide. See Figure 4.6.
IMPORTANT: Auger drive belt will have to be removed
from around engine drive pulley and engine shaft to
install wheel drive belt.
5. Remove wheel drive belt from around engine
pulley. See Figure 4.6.
6. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.7.
SELF-TAPPING "_\
SCREWS
REMOVE
COVER
BELT GUIDE
/ -'J
FIGURE 4.7
7. Remove wheel drive belt from drive disc pulley.
Route wheel belt through drive system in between
rubber drive tire and drive disc.
8. Route new wheel drive belt through drive
system. NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position
it around auger pulley.
9. Route wheel drive belt onto engine wheel drive
pulley. Make sure belt is also positioned in the drive
disc pulley groove.
10. Reinstall auger drive belt around engine auger
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
11. Position belt guide against auger drive belt and
tighten securely.
12. Reinstall both idler springs.
13. Reinstall discharge chute, belt cover and drive
system cover. Tighten screws securely.
FIGURE 4.6
15