Snapper 84871 User Manual

Not for

Reproduction

Parts Manual fo

r

2

2

0

0

7

2

2

4

6

4

5

8

6

4

7

4

2

28" & 33" Hi-Vac

REAR ENGINE RIDER

SERIES 23

DescriptionModel No.

84871 281023BVE
780010
8487
8494
84874 281123BVE
84883 281123HVE
708494
780064
8562
708562
780010
7800649 2812523BVE
8487
708562
85624 2813523BVE
8488
8487
7084879 331523KVE
780010
84879 331523KVE
708495
780010
84954 331723BVE
780025
780065
84881 W280923BV
84884 W281023BVE

281123BV
281123BV
281123BV

2811523BV
2811523BV
2812253BVE
2812523BVE
2812523BVE

281323BVE
2813523BVE

331323HVE
331523BVE

331523KVE

331723BVE
331723BVE

3317523BVE
3317523BVE

Briggs & Stratton Yard Power Products Group

535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967

Manual No. 7006279
Revision: B 12/6/2010

Not for

Reproduction

Not for

Reproduction

PAGE GROUP

4 WHEELS, FRONT & REAR
6 FRONT END, STEERING

8 MAIN CASE & L.H. FENDER
12 LEFT HAND FENDER & BEARING
14 DIFFERENTIAL, R. H. FENDER
16 YOKE LIFT COMPONENTS
18 PRIMARY CHAIN CASE & SMOOTH CLUTCH
20 GEAR SHIFTER ASSEMBLY
22 FUEL TANK & SEAT
24 ENGINE, MUFFLER & DRIVE DISC
26 CUTTING DECKS & DEFLECTOR (28" & 33" Hi-Vac)
28 BELTS, BRAKES & INTERLOCK
30 RAILS, LIFT ARMS & CAM LIFT
32 BLADE STOP PEDALS
34 SPINDLE
36 DECALS
38 ELECTRICAL SYSTEMS (Briggs Magneto Ground)
40 ELECTRICAL SYSTEMS (For 9, 11 & 11.5HP Briggs Recoil)
42 ELECTRICAL SYSTEMS (For 10, 11, 12, 12.5 & 13HP Briggs)
44 ELECTRICAL SYSTEMS (For 13.5, 15, 16, 17 & 17.5HP Briggs)
46 ELECTRICAL SYSTEMS (For 11 & 13HP Honda)
48 ELECTRICAL SYSTEMS (For 15HP Kohler)
50 ELECTRICAL SYSTEMS (Kohler Magneto Ground)
52 WIRING SCHEMATIC (9, 11 & 11.5HP Recoil Start Briggs)
54 WIRING SCHEMATIC (10, 11, 12, 12.5 & 13 HP Briggs)
56 WIRING SCHEMATIC (13.5, 15, 16, 17 & 17.5HP Briggs Engines)
58 WIRING SCHEMATIC (11 & 13 HP Honda Engines)
60 WIRING SCHEMATIC (14 & 15 HP Kohler Engines)
62 HARDWARE BAGS
66 ACCESSORIES & ATTACHMENTS

Table Of Contents

28" & 33" Hi-Vac
SERIES 23

Manual No. 7006279

3

TP 400-5457-B-RE-N

Not for

Reproduction

WHEELS, FRONT & REAR

Manual No. 7006279 28" & 33" Hi-Vac

4

SERIES 23

Not for

Reproduction

WHEELS, FRONT & REAR

Part No DescriptionItem Qty

1 7058943 2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 2, 3, 4, 5 & 6)
2 7073563 1 TIRE, 11 x 4.00-4 (Kenda)
3 7017146 1 RIM (For 4.10/3.50 x 4 Tire)
4 7011807 2 BALL BEARING, Flange (3/4” I.D.)
5 7012234 1 VALVE STEM, Snap In
6 7014669 1 * LUBE Fitting, Straight (for 3/16" hole)
6 7076998 1 * LUBE Fitting, Straight (for 1/4" hole)
6 7010909 1 * LUBE Fitting, 90 Degree, Ball Check (for 1/4" ho le)
6 7104428 1 * LUBE Fitting, 90 Degree, Ball Check (for 5/16" hole)
7 7031038 1 CAP, Dust
8 7011032 1 FELT SEAL
9 7010935 3 WASHER, .77 x 1.13 x .06 Flat
10 7011022 1 HUB CAP
11 7091516 1 COTTER PIN, 5/32 x 1”
12 7010821 1 TUBE, Inner (For 4.10/3.50 x 4 Tire)
13 7058951 2 ASSEMBLY, Rear Tire & Rim (28” & 33” Models) (Includes Items 5, 14 & 15)
14 7073584 1 TIRE, 16-6.50 x 8
15 7012163 1 RIM, Extra Wide (For 16/7.50 x 8 Tire) (33” Models) was 7017147
16 7040434 1 HUB, Rear Wheel LH, 3 Hole 3/4" ID
17 7040433 1 HUB, Rear Wheel RH, 3 Hole 1" ID
18 7011035 1 AXLE BOLT, Left Hand (5/16-24 x 1-5/8” Tapered)
19 7092062 1 NUT, Wheel Bolt, 5/16-24 Hex Center Lock was 7011201
20 7023522 1 CAP, Hub, L. H. (Long Axle)
21 7011013 1 WHEEL BOLT, Right Hand (5/16-24 x 2” Tapered)
22 7023895 1 CAP, Hub
23 7011817 1 SEAL, 1.22” ID x 1.875” OD CAP, Seal 1.0” ID x 1.67” OD
24 7031732 1 CAP, Seal 1.0” ID x 1.67” OD, Right Hand (8 & 10 HP)
25 7012332 1 CLAMP, Right Hand 2” (used on 8, 10, 11.5, 12.5, 13 & 17 HP)
25 7014542 1 CLAMP, Right Hand 2.69” (used on 12, 14 & 15 HP)
26 7091502 3 BOLT, 1/2-20 x 3/4” Lug, GR 5

Footnotes:

NOTE* Different size holes used, measure hole for proper fit.

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

5

Not for

Reproduction

FRONT END, STEERING

Manual No. 7006279 28" & 33" Hi-Vac

6

SERIES 23

Not for

Reproduction

Part No DescriptionItem Qty

1 7058030 1 ASSEMBLY, Steering Wheel (for 5/8” shaft) (Includes item 2)
2 7023781 1 LOGO, Steering Wheel
3 7013862 1 ROLL PIN, 1/4 x 1-1/2”
4 7023667 1 FOAM COVER, Steering Shaft
5 7023671 1 COVER, Steering Shaft
6 7090296 1 PIN, 3 /16 x 1” Cotter
7 7090183 2 WASHER, .66 x 1.31 x .09 Flat
8 7046158 1 BUSHING, Nylon
9 7101192 1 CABLE, Brake, Snap-In (replaces 7072648)
10 7022449 1 CABLE, Clutch/Brake (54.32” long) (used on 25” & 28” Decks)
10 7074131 1 CABLE, Clutch/Brake (55” long) (used on 33” Decks)
11 7090372 1 NUT, 1/4-20 Hex Center Lock, GR 5 or B
12 7034174 2 CONNECTOR, Cable
13 7091495 1 SCREW , 1/4-20 x 3/4” Hex Head Cap, GR 5
14 7054378 1 WELDMENT, Front Axle, Narrow (used on 25” & 28” Decks)
14 7053266 1 W E LDMENT, Front Axle, Wide (used on 33” Decks)
15 7074561 1 BOTTLE, Water
16 7074560 1 HOLDER, Bottle (Wire)
17 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
18 7011714 1 HAIR PIN 2-1/4”
19 7038243D 1 LATCH, Parking Brake
20 7015444 1 SPRING, Parking Brake Latch
21 7014049 2 FOOT PAD, Short (5.5” x 4.7”)
21 7014048 2 FOOT PAD, Long (5.5” x 9.5”)
22 7010776 1 RING, 1/2” External Retaining (Heavy Duty)
23 7047888BM 1 WELDMENT, Clutch Pedal
24 7011815 1 PAD, Pedal
25 7010694 1 BUSHING, Nylon
26 7046232 1 WELDMENT, Steering Shaft
27 7091515 1 PIN, 3/16 x 1-1/2 ” Cotter (Was 7090753)
28 7010746 2 RING, 5/8” External Retaining
29 7010935 6 WASHER, .77 x 1.13 x .06 Flat
30 7010986 4 BEARING, Nylon
31 7091516 2 PIN, 5/32 x 1” Cotter Was 7090364)
32 7090122 4 WASHER, 3/8” Flat SAE
33 7013321 4 BUSHING, Tie Rod
34 7041687 1 WE LDMENT, King Pin, Left Hand
35 7041688 1 WELD MENT , King Pin, Right Hand
36 7091598 2 PIN, 1/8 x 3/4” Cotter (Was 7090365)
37 7013023 1 TIE ROD, Left Hand (7.41” long)
37 7012541 1 TIE ROD, Left Hand (9.91” long)
38 7012933 1 TIE RO D, Right Hand (7.41” long)
38 7012540 1 TIE RO D, Right Hand (9.91” long)

FRONT END, STEERING

Footnotes:

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

7

Not for

Reproduction

MAIN CASE & L.H. FENDER

Manual No. 7006279 28" & 33" Hi-Vac

8

SERIES 23

Not for

Reproduction

MAIN CASE & L.H. FENDER

Part No DescriptionItem Qty

1 7028990 1 COVER, Battery
2 7028989 1 COVER, Switch
3 7073268 1 COVER, Solenoid
4 7074210 1 BRACKET, Belt Adjuster
5 7091198 2 SCRE W, 3/8-16 x 5/8” He x W a s he r Se l f - Tap
6 7090358 1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR 5
7 7031100 1 TUBE CLAMP
8 7010969 2 NUT, 5/ 16-24 F lange Lock (Large)
9 7074650 1 BUSHING, Pivot (Was 7022509)
10 7053697 1 WELDMENT, Main Case (Standard) (shown)
11 7034299 2 WING, Rear
12 7028200 2 SWIVEL, Adjustable
13 7091503 2 HAIR PIN, 3/32 x 1-1/2”
14 7090793 4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
15 7011791 4 RETAINER, 5/16” Bolt
16 7091296 4 WASHER, 5/16” Flat
17 7091315 7 WASHER, .32 x .58 x .08 Split Lock
18 7091297 7 NUT, 5/16-24 Hex, GR 5
19 7090595 2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR 5
20 7024998 3 PLUG, 1” Hole (Used on Euro models only)
21 7090238 4 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
22 7077692 4 BOLT , M8-1.25 x 25mm, Self-Tap (Kohler)
23 7074946 1 PLATE, Engine (Kohler Engine)
24 7030798 2 BUMPER, Rear
25 7036367 1 BUMPER (1-Piece) (33” Deck)
26 7090484 4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap
27 7010153 2 CAP, Bumper
28 7090188 2 WASHER, 11/32” Flat
29 7090361 14 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
30 7090391 1 WASHER, 5/16” Internal Tooth Lock
31 7012652 1 CLIP, Wire
32 7091318 1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5 (Was 7090206)
33 7091513 4 SCREW, 5/16 -24 x 1-3/4” Hex Head Cap, GR 5
34 7091272 7 FASTENER, 1/4” Ratchet
35 7047189 1 BRACKET, Drive Support
36 7090585 6 NUT, 5/16-18 Hex Flange Lock, GR 5
38A 7017653 1 BELT GUIDE, 25 & 28 (5.74” Bolt Pattern, 4.74” Belt Gap)
38B 7036418 1 BELT GUIDE, 33” (5.74” Bolt Pattern, 5.0” Belt Gap) (used on 7800107 & 7800254 models)
39 7023676 1 SHIFT LINK, Long (5/16-24 both ends)
40 7041384 1 WELDMENT, Shift Arm
41 7033799 1 CROSS BRACE
42 7011018 1 SHIFT LINK, Short (5/16-24 thread)
43 7073735 1 BRACKET, Switch
44 7090981 2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap

Footnotes:

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

9

Not for

Reproduction

MAIN CASE & L.H. FENDER

Manual No. 7006279 28" & 33" Hi-Vac

10

SERIES 23

Not for

Reproduction

Part No DescriptionItem Qty

45 7037285 1 FENDER, Left Hand (1.628” I. D. Hole)

MAIN CASE & L.H. FENDER

Footnotes:

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

11

Not for

Reproduction

LEFT HAND FENDER & BEARING

Manual No. 7006279 28" & 33" Hi-Vac

12

SERIES 23

Not for

Reproduction

LEFT HAND FENDER & BEARING

Part No DescriptionItem Qty

1 7012332 2 BOOT CLAMP, 2”
2 7075115 1 BOOT, Rear Axl e, Thick Flange
3 7011072 1 WASHER, Thrust
4 7011071 1 THRUST WASHER
5 7052827 1 ASSEMBLY, DX Bearing (incl. next 3 items shown below)
6 7074182 2 BEARING, DX
7 7074500 1 SEAL, Axle (Dust/Grease)
8 7075848 1 FITTING, Lube, 45 Degree, 3/16” w/Hex (long shank) (or 7013324)
9 7011070 1 TIE ROD (5/16-24 thread - both ends)
10 7037285 1 FENDER, Left Hand (1.628” I. D. Hole)
11 7010969 1 NUT, 5/16-24 Flange Lock (Large)
12 7012271 1 WASHER, Shim (or quantity as required)

Footnotes:

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

13

Not for

Reproduction

DIFFERENTIAL, R. H. FENDER

Manual No. 7006279 28" & 33" Hi-Vac

14

SERIES 23

Not for

Reproduction

DIFFERENTIAL, R. H. FENDER

Part No DescriptionItem Qty

1 7091819 13 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap (Was 7090362)
2 7012296 1 BEARING, Axle (R. H. Fender)
2 7054372 1 BEARING-DX, Axle (R. H. Fender) (includes 1-1/8” I.D. (DX) bearing)
3 7010969 1 NUT, 5/ 16-24 F lange Lock (Large)
4 7031079 1 WASHER, Thrust
5 7038067 1 PLATE, Differential (Note: 4 holes offset - align properly to prevent binding.)
6 7022115 4, 8 SPACER, Pinion
7 7021127 4, 8 GEAR, Differen tial Pinion (12T 12P)
8 7011072 1 WASHER, Thrust
9 7051584 1 * ASSEMBLY, Drive Hex Tube
10 7010988 1 WASHER, Nylon
11 7200128 1 GEAR, 11 Tooth, 10 Pitch (Was 7010964)
12 7010941 1 CHAIN, 46 Pitch (#35 Endless)
13 7021129 1 SPROCKET, 34T, 3/8P
14 7010965 1 RING, 1-3/16” External Retaining
15 7021128 1 SPACER, Differential Case
16 7012332 2 BOOT CLAMP, 2”
17 7075115 1 BOOT, Oil Seal (Short Axle)
18 7011024 2 PLUG, 1/2” Cup Insert
19 7037279 1 CASE, Transmission
20 7028762 1 GASKET, Transmission Case
21 7037280 1 FENDER, Right Hand (1.62” Dia. Hole)
22A 7021158 1 GEAR, 63 Tooth 10 Pi tch (4 Hole)
22B 7027644 1 GEAR, 63 Tooth 10 Pi tch (8 Hole)
23 7047763 1 KIT, Long Axle Structure (Includes spacer 7074431) (Was 7047763)
24 7074431 1 SPACER, Differential Case
25 7057398 1 ASSEMBLY, Short Axle, 23T (Includes Gear)
26 7012333 4, 8 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist)
27 7011156 2 O-RING, 5/16”
28 7011782 2 WASHER, 5/16” Belleville
29 7090395 1 WASHER, 5/16” External Tooth Lock
30 7090188 1 WASHER , .34 x .69 x .08 Flat
31 7011042 1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
32 7090361 11 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
35 7061017 GREASE, Transmission (24 oz. Required)

7060411 1 KIT, Differential (4 Pinion)
7060662 1 KIT, Differential (8 Pinion w/DX Bearing)
7060412 1 KIT, Long & Short Axle (Includes items 23, 24, & 25)

Footnotes:

Note: * Assembly includes two bearings inside hex tube (p/n 7015140, not shown) & one nylon washer (p/n 7010988, item

10).

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

15

Not for

Reproduction

YOKE LIFT COMPONENTS

Manual No. 7006279 28" & 33" Hi-Vac

16

SERIES 23

Not for

Reproduction

YOKE LIFT COMPONENTS

Part No DescriptionItem Qty

1 7013885 1 SPRING, Clutch & Brake
2 7014664 1 BOLT, 5/16-18 Shoulder
3 7091198 2 SCRE W, 3/8-16 x 5/8” He x W a s he r Se l f - Tap
4 7090187 1 WASHER, 5/16” S plit Lock
5 7091511 1 NUT, 5/ 16-18 Hex, GR 5 or B (W as 7090196)
6 7014663 2 SLIDE HALF
7 7047190 1 BRACKET, Slide
8 7090122 2 WASHER, 3/8” Flat SAE
9 7015464 1 STUD, Clutch Link (3/8-24 thread)
10 7091597 1 PIN, 3/32 x 3/4” Cotter (Was 7090037)
11 7090390 1 WASHER, 3/8” Internal Tooth Lock
12 7091630 1 NUT, 3/8-24 Hex, GR 5 or B (Was 7090155)
13 7091122 2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap (Was 7090539)
14 7059068 1 ASSEMBLY, Leaf Spring
15 7073733 1 ARM, Yoke
16 7046162 1 LIFT, Yoke
17 7092062 2 NUT, 5/16-24 Hex Center Lock (Was 7011201)
18 7011048 2 BEARING, Yoke
19 7011763 2 FENDE R WASHER, 5/16”
20 7090238 2 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
21 7033291 1 COLLAR, Yoke

Footnotes:

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

17

Not for

Reproduction

PRIMARY CHAIN CASE & SMOOTH CLUTCH

Manual No. 7006279 28" & 33" Hi-Vac

18

SERIES 23

Not for

Reproduction

PRIMARY CHAIN CASE & SMOOTH CLUTCH

Part No DescriptionItem Qty

1 7052683 1 ASSEMBLY, Primary Chain Case (Includes the following 16 items)
2 7041136 1 WELDMENT, Prima ry Chain Case Half , Right Hand
3 7028761 1 GASKET, Primary Chain Case
4 7011121 2 WASHER, 5/8” Belleville
5 7010756 2 BEARING, .625 x 1.37 x .435
6 7018963 1 WELDMENT, Sprocket & Shaft
7 7010614 1 KEY, #5 Woodruff
8 7039778 1 PRIMARY CHAIN CASE HALF, Left Hand
9 7010942 2 BEARING, Needle 1.355” ID x 1.6245” OD x .5” Wide
10 7011086 2 THRUST WASHER, Nylon
11 7040355 1 WELDMENT, Hub & Sprocket
12 7010941 1 CHAIN, 46 Pitch (#35 Endless)
13 7090917 10 SCREW, 10-24 x 1/2” Hex Washer Self-Tap (Was 7090307)
14 7022785 1 ROLLER, 1-3/8 Long
15 7010776 1 RING, 1/2” External Retaining (Heavy Duty)
16 7011024 1 PLUG, 3/4” Cup Insert
17 7091505 1 NUT, 5/8-18 Hex Nyloc
18 7019260 2 O-RING, 1/2 x 5/8”
19 7027981 1 WASHER, Shim .625 x .875
20 7053114 1 ASSEMBLY, Smooth Clutch (non-asbestos) (Includes the following 5 items)
21 7059443 1 HUB, Driven Disc (assembly) (Was 7054243)
22 7053103 1 DISC, Driven (rubber tire bonded to rim)
23 7014523 1 THRUST WASHER
24 7032331 1 PLATE, Drive Disc
25 7092081 4 NUT, 5/16-24 Hex Flange Lock (Was 7090480, center lock flange nut)
26 7052497 1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
27 7012313 1 RING, 3/8” External Retaining
28 7090303 1 NUT, 1/4-28 Hex Top Lock
29 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
30 7072593 1 * SPACER, Brake Arm Pivot (.418/.403 long) (Was 7010916 (.300/.285 long))
31 7091504 1 SCREW, 1/4-28 x 1” Hex Head Cap, (Wa s her Face) GR 5
32 7072406 1 * SPRING, Torsional Brake Return
33 7061017 ** GREASE, Transmission (Use 2 oz. Maximum)

Footnotes:

Note: * Brake return replacement kit (7061197) is made of items 30 & 32.
NOTE: ** Maximum capacity of chain case before causing leakage at bearing is 2 oz. DO NOT OVERFILL!

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

19

Not for

Reproduction

GEAR SHIFTER ASSEMBLY

Manual No. 7006279 28" & 33" Hi-Vac

20

SERIES 23

Not for

Reproduction

Y

Part No DescriptionItem Qty

1 7023656 1 GRIP, Shift Handle
2 7059212 1 WELDMENT, Shift Handle
3 7023914 1 PIN, 1/4 x 1-3/4” Tapered Cle vis
4 7091597 1 PIN, 3/32 x 3/4” Cotter (Was 7090037)
5 7031036 2 WASHER, Thrust
6 7019245 1 BUSHI NG, 3/4 x 1.62 Flange (Nylon)
7 7091298 1 NUT, 5/16-18 H ex Nyloc
8 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
9 7058763 1 * ASSEMBLY, Speed Adjustment Latch
10 7026292 1 SPRING (part of Speed Adjustment Latch Ass'y)
11 7091511 1 NUT, 5/16-18 Hex, GR 5 or B (Was 7090196)
12 7010754 1 SPRING, Shift Detent
13 7073289 1 LEVER, Over-Ride
14 7091595 1 WASHER , .47 x .92 x .065 Flat
15 7015761 1 SHOULDER BOLT, 5/16-18
16 7019246 1 BUSHING, 3/4 x I.O. Flange (Nylon)
17A 7040598 1 WELDMENT, Arm, Shift Handle
17B 7043201 1 WELDMENT, Arm, Shift Handle (w/grease ftg. Hole)
18 7010817 1 LUBE FITTING, 3/16” Press-In (used with 7043201)
19 7091315 1 WASHER, .32 x .58 x .08 Split Lock
20 7091297 1 NUT, 5/16-24 Hex, GR 5

GEAR SHIFTER ASSEMBL

Footnotes:

Note: * Assembly is comprised of: Shift Detent Weldment (7041232), Shoulder Rivet (7029022), Reverse Stop (7073218) &
item 10.

SERIES 23

Manual No. 700627928" & 33" Hi-Vac

21

Not for

Reproduction

FUEL TANK & SEAT

Manual No. 7006279 28" & 33" Hi-Vac

22

SERIES 23