Parts Manual for
SHOWN
TWO STAGE
LARGE FRAME
SNOW THROWER
SERIES 5
MODELS
8245
8265
E8265
MODEL 10305E
9265
E9265
10305
11305
10305E
E10305
E10305E
E11305
IT IS THE POLICY O F SNAPPER TO IMPRO VE ITS PRO DUCTS WHENEVER IT IS POSSIBL E
AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH
CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
COPYRIGHT © 2000
SNAPPER INC.
ALL RIGHTS RESERVED
(Rev. 5, 7/03/00) MANUAL No. 06037
FAMILIARIZATION
DISCHARGE CHUTE
Pages 4 & 5
DIRECTIONAL CONTROL
Pages 16 - 19
BLOWER HOUSING
Pages 6 & 7
AUGERS
Page 3
SCRAPERS
Pages 6 & 7
LIGHTS
Pages 18 - 19
GEAR BOX, SHAFTS
Pages 10 & 11
BLOWER CLUTCH
Pages 16 - 19
SKID SHOES
Pages 6 & 7
MODEL 10305E SHOWN
HARDWARE
BAG KITS
PAGE 25
MANUAL No. 06037 LARGE FRAME SNOWTHROWER
CHUTE CONTROL
Page 16 - 19
TRACTION CLUTCH
Pages 16 - 19
DECALS
Pages 22 - 24
HANDLE BARS
Pages 16 - 19
CONTROL PANEL
Pages 16 - 19
ENGINE
Page 20
FRAME
Pages 12 & 13
WHEELS
Page 21
TRACTION DRIVE
Pages 14 & 15
IMPELLER
Page 3
ACCESSORIES
PAGE 25 - 27
2
AUGERS, IMPELLER
RIGHT SIDE
ITEM PART NO. DESCRIPTION
GEARBOX, SHAFTS
(See Pages 8 – 9)
LEFT SIDE
1 4-9928 AUGER, Right Side (8245 Models)
- 4-9935 AUGER, Right Side (8265, 9265 & E9265 Models)
- 4-9922 AUGER, Right Side (10305E, E10305E, N10305E, 11305 &
E11305 Models)
2 1-3864 FITTING, Grease (2)
3 9-1550 BOLT, 5/16-18 x 1-7/8" Shear (2)
4 9-1298 NUT, 5/16-18 Hex Nyloc (2)
5 4-9927 AUGER, Left Side (8245 Models)
- 4-9936 AUGER, Left Side (8265, 9265 & E9265 Models)
- 4-9921 AUGER, Left Side (10305E, E10305E, N10305E, 11305
E11305 Models)
6 4-9677 FAN, Impeller
7 1-3862 PIN, 1/4 x 1-1/2" Roll (2)
8 5-1350 ASSEMBLY, Bearing (Includes Item 11)
9 9-0699 BOLT, 1/4-20 x 3/4" Hex Flange Lock, Grade 5 (6)
10 9-1065 NUT, 1/4-20 Hex Flange Lock (6)
11 1-0817 FITTING, Grease (2)
12 2-8221 SPACER (Used on Model 8245 Models Only) (2)
LARGE FRAME SNOWTHROWER MANUAL No. 06037
3
DISCHARGE CHUTE
(PART OF CONTROL CABLE)
5B
5A
6
23
9
19
22
24
4
14
26
18
16
20
17
13 10
7
8
MANUAL No. 06037 LARGE FRAME SNOWTHROWER
#10-32 HEX JAM NUTS and
#10 LARGE OUTSIDE DIAMETER
FLAT WASHERS
19
COLLECTOR HOUSING
21
25
6
3
2
25
15
14
1
12
11
4
DISCHARGE CHUTE
ITEM PART NO. DESCRIPTION
1 2-8208 CHUTE, Discharge
-- 2-8217 CHUTE, Remote Control Discharge (8245 Model Only)
2 2-4773 DECAL, Hand Danger
3 2-8235 DEFLECTOR, Remote Control Discharge
-- 2-8184 DEFLECTOR (8245 Model Only)
4 2-8253 PIN, Hinge
5A 1-6324 T-KNOB (Plastic)
5B 3-5744 T-KNOB (w/5/16-18 insert)
6 9-1076 WASHER, 5/16 Flat (2)
7 9-1072 BOLT, 5/16-18 x 1” Square Neck Carriage, Grade 5
8 9-1021 SCREW, 5/16-24 x 3/4" Hex Head Cap, Grade 5 (3)
9 9-1074 NUT, 5/16-24 Hex Center Lock, Grade B
10 3-9765 RING, Chute (59 Tooth, 229 Degrees)
-- 4-7855 RING, Chute (Euro) (48 Tooth, 187 Degrees)
11 1-1938 RETAINER (Chute Ring to Housing) (2)
12 9-1077 BOLT, 5/16-18 x 5/8" Square Neck Carriage, Grade 5 (3)
13 9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (3)
14 9-1075 SCREW, #10-24 x 5/8" Hex Washer Self-Tap, Grade 5 (8)
15 9-1069 NUT, 5/16-18 Hex, Grade B or 5
16 3-2813 MOUNT, Cable
17 9-1064 BOLT, 1/4-20 x 1/2" Short Neck Carriage, Grade 5 (2)
18 9-1023 WASHER, 1/4” Internal Tooth Lock (2)
19 9-1100 NUT, 1/4-20 Hex (3)
20 4-5172 CABLE, Control
21 9-1099 NUT, 1/4-20 Hex Center Lock, Grade B or 5
22 9-1098 WASHER, 1/4 Flat (2)
23 2-3798 BOLT, 1/4-20 x 1-1/2" Eye
24 1-9692 WIRE, Safety
25 2-3673 PUSH-ON Fastener, 5/32” Dia. (2)
26 3-2559 RETAINER, Safety Wire (2)
LARGE FRAME SNOWTHROWER MANUAL No. 06037
5
COLLECTOR HOUSING
30
11
13
20
28
29
24
15
21
26
32
MANUAL No. 06037 LARGE FRAME SNOWTHROWER
20
5
31
21
19
25
23
22
22
2
7
5
14
27
22
13
8
10
6
1
9
16
25
19
12
18
4
3
17
5
6
COLLECTOR HOUSING
ITEM PART NO. DESCRIPTION
1 5-2134 ASSEMBLY, 24" Blower (8245 Models) (Includes 1-6578 Decal)
-- 5-2135 ASSEMBLY, 26" Blower (8265 & 9265 Models) (Incl. 1-6578 Decal)
-- 5-3421 ASSEMBLY, 30" Blower (10305E & 11305E Models) (Includes 2-6629 Decal)
2 3-3035 GUIDE, Cable (8265, 9265, E9265, 10305E, E10305E, N10305E),
11305 & E11305)
3 9-1021 SCREW, 5/16-24 x 3/4” Hex Head Cap, Grade 5
4 9-1074 NUT, 5/16-24 Hex Center Lock, Grade B
5 9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (9)
6 2-8280 DECAL, Danger Rotating Auger
-- 2-8711 DECAL, Foot Danger (Euro)
7 2-8281 DECAL, Heavy Duty Snow
8 3-4303 BRACKET, Worm Shaft Support
9 1-2117 BUSHING
10 1-4001 PIN, 1/8 x 3/4" Roll
11 2-8222 CONNECTOR
12 4-2809 SHAFT, Worm (3/8-16 threaded)
13 1-1724 WASHER, 13/32 Spring (2)
14 2-8348 WORM
15 9-0539 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
16 9-0858 SCREW, 5/16-18 x 1/2" Hex Washer Self-Tap (2)
17 3-8009 BAR, Stiffener (10305E, 11305 & E11305 Models Only)
18 9-1082 PIN, 3/32 x 3/4" Cotter
19 3-7982 SHOE, Skid (2)
20 9-0324 SCREW, 3/8-16 x 1" Hex Washer Self-Tap (2)
21 1-6360 WASHER, 3/8” Flat
22 9-0001 BOLT, 5/16-18 x 3/4" Short Neck Carriage, Grade 5 (11)
23 9-0731 BOLT, 5/16-18 x 1/2" Short Neck Carriage, Grade 5 (5)
24 3-6122 BLADE, Scraper (8245 Models)
-- 3-9770 BLADE, Scraper (8265 & 9265 Models)
-- 3-6006 BLADE, Scraper (10305E, 11305 & E11305 Models)
25 9-1076 WASHER, 5/16 Flat
26 2-8177 BRACKET, Worm
27 4-2894 PLUG, Dome 5/16” (2)
-- 4-2895 PLUG, 5/16” Dome (2)
28 9-1514 WASHER, 3/8” Flat
29 9-1585 NUT, 3/8-16 Hex Center Lock, Grade 5 or B
30 3-7971 DRIFT CUTTER (2)
31 9-0187 WASHER, 5/16 Split Lock (4)
32 9-0196 NUT, 5/16-18 Hex (4)
LARGE FRAME SNOWTHROWER MANUAL No. 06037
7
BELTS, IDLER, DRIVE PLATE, SHEAVE
4
14
18
MANUAL No. 06037 LARGE FRAME SNOW THROWER
12
3
2
29
15
13
13
5
10
16
1
28
26
11
18
6
7
23
10
24
8
25
9
17
20
22
27
23
ENGINE PULLEY
(See Page 20)
IDLER
(See Page 20)
21
22
24
19
8
BELTS, IDLER, DRIVE PLATE, SHEAVE
ITEM PART NO. DESCRIPTION
1 5-3580 ASSEMBLY, Idler Arm (Includes Items 2 & 3)
2 9-1559 RIVET (2)
3 1-3859 PAD, Brake
4 1-3919 SPRING
5 9-0791 BOLT, 3/8-16 x 1-1/2" Square Neck Carriage, Grade 2
6 9-0122 WASHER, 3/8 Flat
7 1-3850 PULLEY, Idler
8 9-0499 NUT, 3/8-16 Hex Top Lock
9 9-1069 NUT, 5/16-18 Hex, Grade B or 5
10 1-6314 WASHER, 5/16 x 1-1/4" Flat
11 1-3849 SPACER
12 9-1072 BOLT, 5/16-18 x 1" Square Neck Carriage, Grade 5
13 1-3931 HOUSING, Bearing
14 1-3924 BEARING (Includes Two #10-32 Socket Set Screws)
15 9-0001 BOLT, 5/16-18 x 3/4" Short Neck Carriage, Grade 5
16 9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (3)
17 1-3867 SHEAVE, Blower (Includes Two 5/16 Set Screws)
18 1-3937 BELT, Blower (All Models with Briggs Engines)
-- 1-3939 BELT, Blower (All Models with Tecumseh Engines)
19 1-0776 RING, 1/2 External Snap (Heavy Duty)
20 1-3861 KEY, #11 Woodruff
21 5-1358 PLATE, Drive (Includes Item 22)
22 1-4295 BEARING, Ball (2)
23 1-3936 BELT, Traction (All Models with Briggs Engines)
-- 2-9101 BELT, Traction (All Models with Tecumseh Engines)
24 1-4296 WASHER, 1/2 Shim (4) (Used with Item 21) (4)
25 9-0187 WASHER, 5/16 Split Lock
26 1-7734 COVER, Belt Guard
27 9-1122 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap
28 3-4302 WASHER, 3/4 x 1-1/8" Flat
29 1-1791 RETAINER, 5/16 Bolt
LARGE FRAME SNOWTHROWER MANUAL No. 06037
9
GEARBOX, SHAFTS
13
1
MANUAL No. 06037 LARGE FRAME SNOW THROWER
1
16
5
7
2
3
12
14
19
20
21
10
6
18
4
17
8
4
15
11
9
11
5
NOTE: USE 4 OZ. OF #2-9577
BENALENE 900 GREASE
FOR LUBRICATION.
10
GEARBOX, SHAFTS
ITEM PART NO. DESCRIPTION
1* 2-8220 SHAFT, Auger (8245 Models)
- 2-7639 SHAFT, Auger (8265 & 9265 Models)
- 2-9552 SHAFT, Auger (10305E, 11305 & E11305 Models)
2 1-3857 KEY, 1/4 x 7/8" Woodruff
3 5-1305 GEAR, Worm
4 1-3855 WASHER, 1.0 x 1-1/2" Thrust (2)
5 1-3858 SEAL, 1-1/2” O.D. Oil (2)
6 1-8451 COVER, Gear Case
7 9-0290 SCREW, 1/4-20 x 3/4" Hex Washer Self-Tap (4)
8 1-3854 O-RING, Case Cover
9 1-9674 CASE, Gear
10 9-0815 SCREW, 3/8-16 x 1/2" Hex Washer Self-Tap
11 2-7630 SHAFT, Impeller
12 1-3313 BEARING, Impeller Shaft
13 1-3862 PIN, 1/4 x 1-1/2" Roll
14 1-3856 SPACER, Gear Bearing
15 1-3861 KEY, 3/16 x 7/8" Woodruff
16 2-7606 GEAR, Rolled Worm
17 1-0935 WASHER, 3/4 x 1-1/8" Thrust (2)
18 1-2252 BUSHING, Impeller Shaft
19 1-3853 O-RING, Case Cap
20 1-8450 CAP, Case
21 9-1075 SCREW, #10-24 x 5/8" Hex Washer Self-Tap (3)
*NOTE: The following assemblies are made
of items 1 through 21 above:
5-3426, 24” Gear Case Assembly
5-7305, 26” Gear Case Assembly
5-7304, 30” Gear Case Assembly
LARGE FRAME SNOWTHROWER MANUAL No. 06037
11
FRAME, TRACTION DRIVE
25
3 43
39
41 40
5
6 2
1
40 39
38
38
40
20
41
40
21
22
42
26
23
8 44
36
19
37
39
14
2
28
27
15 32
33
12
11
19
45
13
31
7
4
24
35
19
18
1 (Ref.)
10
16
9
17
30
34
29
9
CHAIN CASE
(See Pages 14 & 15)
MANUAL No. 06037 LARGE FRAME SNOW THROWER
CLUTCH LEVER
(See Pages 16 – 19)
46
44
44
WHEELS
& HUBS
(Page 21)
12
FRAME, TRACTION DRIVE
ITEM PART NO. DESCRIPTION
1 1-9684 ROD, Activating
2 1-2117 BUSHING (2)
3 1-3887 ROD, Lower Shift
4 3-9768 COVER, Frame Back
5 3-7967 LEVER, Shift
6 1-3872 STUD, Shift Lever
7 3-2124 BELLCRANK, Traction
8 3-4306 FRAME (Order Items 9 & 10 When Replacing)
9 1-5363 BUSHING, Axle Shaft (2)
10 1-3874 BUSHING, Hex Shaft
11 1-0756 BEARING
12 3-2121 RETAINER, Bearing
13 3-9769 COVER, Frame Bottom
14 1-8460 GEAR, Axle Shaft
15 2-7610 SHAFT, Hex
16 1-0614 KEY, 1/8 x 5/8" Woodruff
17 1-3884 PINION, Hex Shaft
18 3-2120 BRACKET, Idler Mounting
19 2-8209 SHAFT, Axle
20 5-7276 BRACE, Frame (10305E, 11305 & E11305 Models Only)
21 3-7965 BRACKET, Clutch
22 3-2130 BRACKET, Spring
23 1-2264 SPRING
24 2-1843 SHAFT, Cross
25 9-1082 PIN, 3/32 x 3/4" Cotter
26 1-3875 ROD, Push
27 1-3878 PIN, 3/16 x 1-1/4" Roll (2)
28 1-3861 KEY, 3/16 x 7/8" Woodruff
29 3-4302 WASHER, 3/4 x 1-1/8" Flat
30 9-1064 BOLT, 1/4-20 x 1/2" Short Neck Carriage, Grade 5 (2)
31 9-1065 NUT, 1/4-20 Hex Flange Lock
32 9-0858 SCREW, 5/16-18 x 1/2" Hex Washer Self-Tap (3)
33 1-1763 WASHER, 5/16 x 1" Flat
34 1-0690 WASHER, 5/8 Shim
35 9-0001 BOLT, 5/16-18 x 3/4" Short Neck Carriage, Grade 5 (3)
36 9-1612 BOLT, 5/16-18 x 1-1/2" Sqare Neck Carriage, Grade 5
37 1-1791 RETAINER, 5/16 Bolt (4)
38 9-0206 SCREW, 5/16-18 x 3/4" Hex Head Cap, Grade 2
39 9-1067 NUT, 5/16-18 Hex Center Lock, Grade B (3)
40 1-6314 WASHER, 5/16 x 1-1/4" Flat (4)
41 1-3849 SPACER, 5/16 x 5/8" (2)
42 9-1084 SCREW, 1/4-20 x 3/8" Hex Washer Self-Tap
43 9-1302 NUT, 3/8-16 Hex, Grade B or 5
44 9-0361 SCREW, 5/16-18 x 5/8" Hex Washer Self-Tap (20)
45 9-0362 SCREW, 1/4-20 x 5/8" Hex Washer Self-Tap (4)
46 3-4303 BRACKET, Worm Shaft
LARGE FRAME SNOWTHROWER MANUAL No. 06037
13
CHAIN CASE (TRACTION DRIVE)
18
14
22
11
4
10
8
13 5
14
15
5
2
CHAIN CASE ASSEMBLY
MANUAL No. 06037 LARGE FRAME SNOW THROWER
3
7
HEX SHAFT
(See Item #15, Pages 12- 13
NOTE: USE “00” GREASE
FOR LUBRICATION
12
8
1
19
20
17
21
16
6
9
7
14
CHAIN CASE (TRACTION DRIVE)
ITEM PART NO. DESCRIPTION
1 5-1269 ASSEMBLY, Chain Case (Includes Items 2 Thru 22)
2 3-3543 COVER, Sprocket
3 9-0913 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx)
4 2-8761 GASKET
5 1-0756 BEARING, Ball (2)
6 1-0940 ASSEMBLY, Shaft & Sprocket
7 1-3881 BUSHING (2)
8 1-3882 WASHER, Thrust (2)
9 1-0941 CHAIN
10 4-0465 ASSEMBLY, Hub & Sprocket
11 4-7776 CHASE, Sprocket
12 2-0908 ROLLER
13 1-0776 RING, 1/2” External Snap (Heavy Duty)
14 1-1121 WASHER, Belleville (3)
15 1-0614 KEY, 1/8 x 5/8" Woodruff
16 9-0356 NUT, 5/8-18 Hex Center Lock Jam
17 5-0614 ASSEMBLY, Drive Disc (Includes Items 18 Thru 22)
18 1-0765 DISC, Drive
19 9-0731 BOLT, 5/16-18 x 1/2" Short Neck Carriage, Grade 5 (3)
20 2-0911 HUB
21 9-0585 NUT, 5/16-18 Hex Flange Lock, Grade 5 (3)
22 1-1024 PLUG
LARGE FRAME SNOWTHROWER MANUAL No. 06037
15
HANDLES, CONTROLS (MODELS 8245)
16 21
23
11 34 25
10
15 35
28 31
2
19 26
10
32
29
5
33
MANUAL No. 06037 LARGE FRAME SNOW THROWER
3
4
6
30
27
14
9
1
13
12
8
7
22
18
24
17
34
29
16
6
4
30
2
27
5
20
33
16
HANDLES, CONTROLS (MODELS 8245)
ITEM PART NO. DESCRIPTION
1 3-2922 BAR, Right Side Handle
2 3-2921 BRACKET, Handle (2)
3 3-2908 HANDLE, Right Side
4 2-8189 GRIP, Handle (2)
5 2-8223 CABLE, Clutch (2) (Includes Chain & Spring)
6 9-1020 NUT, 1/4 Push (2)
7 9-1074 NUT, 5/16-24 Hex Center Lock, Grade B
8 1-3887 ROD, Lower Shift
9 1-6304 CONNECTOR
10 1-4297 ROD, Upper Shift
11 1-6334 KNOB, Shift Handle
12 4-0660 HANDLE, Shift
13 3-7962 BRACKET, Shift Lever
14 3-4305 PANEL, Control
15 1-2117 BUSHING
16 2-8215 CRANK, Chute
17 1-3901 KNOB, Chute Crank
18 9-1067 NUT, 5/16-18 Hex Center Lock, Grade B (4)
19 2-8214 DECAL, Control- 8/24
-- 4-5177 DECAL, Control- 9/26
-- 4-5183 DECAL, Control- E9/26
20 3-2923 BAR, Left Side Handle
21 3-2907 HANDLE, Left Side
22 2-3933 SPRING, Shift Lever
23 9-1076 WASHER, 5/16 Flat
24 9-1065 NUT, 1/4-20 Hex Flange Lock (3)
25 9-0244 SCREW, 5/16-24 x 1-3/4" Hex Head Cap, Grade 2
26 9-1066 SCREW, 5/16-18 x 1-1/2" Hex Head Cap, Grade 5 (4)
27 9-0303 NUT, 1/4-28 Hex Top Lock (2)
28 9-1067 NUT, 5/16-18 Hex Center Lock, Grade B
29 1-6297 PIN, 1/4 x 1-7/8" Clevis
30 9-1025 SCREW, 1/4-28 x 1-3/8" Hex Head Cap, Grade 5 (2)
31 9-1064 BOLT, 1/4-20 x 1/2" Short Neck Carriage, Grade 5 (3)
32 9-1071 NUT, 3/8-16 Hex, Grade B
33 9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (4)
34 9-0041 PIN, 1/8 x 1" Cotter
35 9-1149 WASHER, 3/8 Flat
(NOTE: See Pages 18 Thru 19 for Models 8265, 9265 & 10305E)
LARGE FRAME SNOWTHROWER MANUAL No. 06037
17
HANDLE, CONTROLS (8265, 9265, 10305E, 11305 & E11305 MODELS)
11
24
3
38
14
10
39
9
2
16
15
20
12
53
6
29
MANUAL No. 06037 LARGE FRAME SNOW THROWER
43
3
1
33
34
45
44
20
32
31
29
42
15
13
30
9
41
8
46
36
16
14
26
25
35
37
23
9
18
27
28
17
40
23
38
4
13
9
20
50
52
47
6
7
8
8
48
21
19
22 7
7
51
18
HANDLE, CONTROLS (8265, 9265, 10305E, 11305 & E11305 MODELS)
ITEM PART NO. DESCRIPTION
1 3-2922 BAR, Handle (Right Side)
2 3-2923 BAR, Handle (Left Side)
3 1-1870 GRIP, Handle (2)
4 3-2907 HANDLE, Left Side
5 1-6573 DECAL, Traction Clutch
6 1-6297 PIN, 1/4 x 1-7/8" Clevis (2)
7 1-6311 CABLE, Left Side Clutch
8 9-1066 SCREW, 5/16-18 x 1-1/2" Hex Head Cap, Grade 5 (4)
9 9-1067 NUT, 5/16-18 Hex Center Lock, Grade B (5)
10 3-3006 PANEL, Control
11 1-2117 BUSHING
12 9-0041 PIN, 1/8 x 1" Cotter
13 9-1025 SCREW, 1/4-28 x 1-3/8" Hex Head Cap, Grade 5 (2)
14 9-1020 NUT, 1/4 Push (2)
15 3-2921 BRACKET, Handle (2)
16 9-0303 NUT, 1/4-28 Hex Top Lock (2)
17 2-8215 CRANK, Chute
18 1-3901 KNOB, Chute Crank
19 9-0074 BOLT, 1/4-20 x 3/4" Short Neck Carriage, Grade 5 (2)
20 9-1065 NUT, 1/4-20 Hex Flange Lock (3)
21 1-5960 GUIDE, Cable
22 3-2651 BRACKET, Cable Guide Support
23 1-3849 SPACER, 5/16” (3)
24 9-1085 BOLT, #10-24 x 1/2" Flat Head Carriage (2)
25 3-2910 LEVER, Clutch
26 9-0548 SCREW, 1/4-20 x 1" Hex Head Cap, Grade 5
27 9-0623 NUT, #10-24 Hex Flange Lock (2)
28 3-8352 BRACKET, Cam
29 1-6310 CABLE, Auger (Right Side)
30 1-5966 SPRING Cam Lock
31 1-5969 SPACER
32 1-8980 LOCK, Cam
33 9-0055 WASHER, 1/4 Flat
34 9-1099 NUT, 1/4-20 Hex Center Lock, Grade B or 5
35 1-6314 WASHER, 5/16 x 1-1/4" Flat (3)
36 3-2908 HANDLE, Right Side
37 9-1064 BOLT, 1/4-20 x 1/2" Short Neck Carriage, Grade 5 (2)
38 9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (4)
39 2-8278 DECAL, Instruction 8265
-- 4-5177 DECAL, Instruction 9265
-- 4-5183 DECAL, Instruction E9265
-- 2-8279 DECAL, Instruction 10305E
-- 2-8695 DECAL, Instruction E10305E & N10305E
-- 7-3483 DECAL, Instruction 11305
-- 7-3482 DECAL, Instruction E11305
40 1-6334 KNOB, Shift Handle
41 4-0660 WELDMENT, Shift Handle
42 3-7962 BRACKET, Shift Lever
43 9-1074 NUT, 5/16-24 Hex Center Lock, Grade B
44 9-1076 WASHER, 5/16” Flat
45 2-3933 SPRING
46 9-0244 SCREW, 5/16-24 x 1-3/4" Hex Head Cap, Grade 5
47 6-1191 KIT, Light Assembly (Rectangular) (2)
48 9-1064 BOLT, 1/4-20 x 1/2" Short Neck Carriage, Grade 5 (2)
49 1-4940 TIE, Cable
50 1-6312 ROD, Upper Shift
51 1-6304 NUT, 3/8-16 x 1-13/16 Connector
52 9-1071 NUT, 3/8-16 Hex, Grade B
53 9-1149 WASHER, 3/8 Flat
LARGE FRAME SNOWTHROWER MANUAL No. 06037
NOTE: See Pages 16 Thru 17
For Models 8245.
19
ENGINES, PULLEY, IDLER
10
ITEM P/N DESCRIPTION
1 3-8545 GUARD, Engine
ENGINE SPECS used on:
2 3-2128 ARM, Idler
3 1-7734 COVER, Belt
8 HP Tecumseh
4 9-0196 NUT, 5/16-18 Hex, Grade B or 5 (4)
Model HMSK80
5 1-0210 KEY, 1/4 x 2" Square
Type 155527V....... 8245, 8265 &
6 1-3850 IDLER
E8265
7 2-8212 SPRING, Idler
8 3-2150 FINGER, Belt
9 HP Tecumseh
9 9-1122 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap (2)
Model HMSK90
10 9-0954 SCREW, 5/16-18 x 5/16" Socket Head Set (4)
Type 156519D........9265 &
11 9-0791 BOLT, 3/8-16 x 1-1/2" Square Neck Carriage, Grade 2
E9265
12 9-1076 WASHER, 5/16 Flat (5)
13 1-3849 SPACER
10 HP Tecumseh
14 1-6314 WASHER, 3/8 Flat
Model HMSK100
15 9-1273 SCREW, 5/16-24 x 7/8" Hex Head Cap, Grade 5
Type 159236W.......10305E &
16 9-0499 NUT, 3/8-16 Hex Top Lock
E10305E
17 1-5376 PULLEY, Blower
Type 159302W.......N10305E
18 1-5377 PULLEY, Traction
Type 159426W 10305 &
19 9-1021 SCREW, 5/16-24 x 3/4" Hex Head Cap, Grade 5
E10305
20 1-5368 CORD, 10’ Extension for 110V (10305 & 10305E Models
Only)(Tecumseh Part Number 1A174-17)
11 HP Tecumseh
-- 7-2611 CORD, 8’ Extension for 230V (E9265 & E10305 Models)
Model OHSK110
21 9-1076 WASHER, 5/16 Flat (4)
Type 221721B........11305 &
22 9-0187 WASHER, 5/16 Split Lock (4)
E11305
23 2-8747 MUFFLER GUARD, Tecumseh 8 & 10 HP (not shown)
(Tecumseh Part Number 127-20)
MANUAL No. 06037 LARGE FRAME SNOW THROWER
20
17
5
15
16
10
14
13
18
8
19
6
1
12
11
2
3
9
20
4
22
21
7
WHEELS, HUB
ITEM PART NO. DESCRIPTION
6
5
2
3
7
8
9
4
1 5-1803 ASSEMBLY, Wheel & Tire (Snow Hog) (8245, 8265, & 9265 Models)
(Includes Items 2A, 3A, & 4)
- 5-1871 ASSEMBLY, Wheel & Tire (Snow Hog) (10305E Models)
(Includes Items 2B, 3B, & 4)
- 5-8916* ASSEMBLY, Wheel & Tire (Kenda) (8245, 9265 & E9265 Models)
(Includes Items 2C, 3C & 4)
- 5-8918* ASSEMBLY, Wheel & Tire (Kenda) (11305 & E11305 Models)
(Includes Items 2D, 3B & 4)
2A 2-3495 TIRE, 16 x 4.80 x 8 (Snow Hog) (8245, 8265 & 9265 Models)
2B 2-3672 TIRE, 16 x 6.50 x 8 (Snow Hog) (10305E Models)
2C 7-3453 TIRE, 16 x 4.80 x 8 (Kenda) (8245, 9265 & E9265 Models)
2D 7-3455 TIRE, 16 x 6.50 x 8 (Kenda) (11305 & E11305 Models)
3A 1-2162 RIM, (8245, 8265 & 9265 Models)
3B 1-2163 RIM, (10305E, 11305 & E11305 Models)
3C 1-2162 RIM, (8245, 9265 & E9265 Models)
4 1-2234 VALVE, Snap-In
5 4-0464 HUB, Wheel (2)
6 1-0935 WASHER, 3/4 x 1-1/8" Thrust
7 9-1502 BOLT, 1/2-20 x 3/4" Hex Head Lug (Nyloc) Grade 5 (6)
8 1-2407 PIN, 5/16 x 1-11/16" Clevis (2)
*NOTE: These wheel assemblies are
used on units built in 2000
for model year 2001)
9 1-5067 PIN, 3/32 x 1-1/2" Hair (2)
LARGE FRAME SNOWTHROWER MANUAL No. 06037
21
DECALS
3
5 4
1
2
7
ITEM PART NO. DESCRIPTION
1 2-9776 DECAL, European Community (CE)
2 7-2820 DECAL, 2000 Year of Manufacture
-- 7-2404 DECAL, 1999 Year of Mfr.(not shown)
-- 3-6434 DECAL, 1997 Year of Mfr.(not shown)
-- 2-9077 DECAL, 1996 Year of Mfr.(not shown)
6
3 2-8280 DECAL, Foot Danger/Blank
4 2-6629 DECAL, Foot Danger/Blank
5 1-6578 DECAL, Danger (Collector)
6 2-7733 DECAL, Ear Protection
7 2-4773 DECAL, Hand Danger
MANUAL No. 06037 LARGE FRAME SNOW THROWER
22
DECALS
9
(Continued)
8
10
11
12
14
13
ITEM PART NO. DESCRIPTION
8 2-8281 DECAL, Heavy Duty Snow
9 2-8711 DECAL, Foot Danger (Euro)
10 2-8700 DECAL, Chute/Read Manual (Euro)
11 2-3009 DECAL, Noise
15
LARGE FRAME SNOWTHROWER MANUAL No.06037
23
12 2-8744 DECAL, Turn To Lock
13 1-2639 DECAL, Start
14 1-6573 DECAL, Traction Clutch
15 7-3342 DECAL, OPEI Snow
DECALS
(Continued)
16
17
18
19
ITEM PART NO. DESCRIPTION
16 2-8279 DECAL, Control- 10/30
17 7-3483 DECAL, Control- 11/30
18 7-3482 DECAL, Control- E11/30
-- 2-8214 DECAL, Control- 8/24 (not shown)
-- 2-8695 DECAL, Ctrl.- E10/30 & N10/30(not shown)
-- 4-5177 DECAL, Control- 9/26 (not shown)
-- 4-5183 DECAL, Control- E9/26 (not shown)
-- 2-8696 DECAL, Control- E8/26 (not shown)
-- 4-5183 DECAL, Control- E9/26 (not shown)
19 7-3844 DECAL, Fuel Safety
MANUAL No. 06037 LARGE FRAME SNOW THROWER
24
ACCESSORIES
PART NO. DESCRIPTION
9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (4)
1-6314 WASHER, 5/16 x 1-1/4" Flat (2)
1-3849 SPACER
3-2910 LEVER, Clutch
2-8223 CABLE, Auger/Cable (2)
9-1067 NUT, 5/16-18 Hex Center Lock. Grade B
9-1071 NUT, 3/8-16 Hex, Grade B
1-6304 NUT, 3/8-16 x 1-3/4" Connector
1-1938 RETAINER, Chute
9-1075 SCREW, #10-24 x 5/8" Hex Washer Self-Tap (2)
1-3865 BOLT, 5/16-18 x 5/8" Shear (2)
9-1298 NUT, 5/16-18 Hex Nyloc (2)
9-0041 PIN, 1/8 x 1” Cotter
9-1082 PIN, 3/32 x 3/4” Cotter
9-1550 BOLT, 5/16-18 x 1-7/8" Shear (2)
9-1149 WASHER, 3/8 Flat
PART NO. DESCRIPTION
9-1070 NUT, 5/16-18 Hex Flange Lock, Grade 5 (8)
1-6314 WASHER, 5/16 x 1-1/4" Flat (2)
1-3849 SPACER
3-2910 LEVER, Clutch
9-1149 WASHER, 3/8 Flat
9-1067 NUT, 5/16-18 Hex Center Lock, Grade B
9-1071 NUT, 3/8-16 Hex, Grade B
1-6304 NUT, 3/8-16 x 1-3/4" Connector
1-1938 RETAINER, Chute
9-1075 SCREW, #10-24 x 5/8" Hex Washer Self-Tap (2)
9-1298 NUT, 5/16-18 Hex Nyloc (2)
9-0001 BOLT, 5/16-18 x 3/4" Short Neck Carriage
9-0187 WASHER, 5/16 Split Lock
9-0196 NUT, 5/16-18 Hex
9-0041 PIN, 1/8 x 1” Cotter
9-1082 PIN, 3/32 x 3/4” Cotter (2)
9-1550 BOLT, 5/16-18 x 1-7/8" Shear (2)
(for Models: E8265, 9265, E9265, 10305, 10305E, E10305, E10305E, 11305 and E11305)
PART NO. DESCRIPTION
9-1070 NUT, 5/16-18 Hex Flange Lock,
Grade 5 (4)
1-6314 WASHER, 5/16 x 1-1/4" Flat (2)
1-3849 SPACER
3-2910 LEVER, Clutch
9-0037 PIN, 3/32 x 3/4" Cotter (2)
9-1067 NUT, 5/16-18 Hex Center Lock,
Grade B
9-1071 NUT, 3/8-16 Hex, Grade B
1-6304 NUT, 3/8-16 x 1-3/4" Connector
1-1938 RETAINER, Chute
9-1075 SCREW, #10-24 x 5/8" Hex
Washer Self-Tap (2)
MANUAL No. 06037 LARGE FRAME SNOWTHROWER
HARDWARE BAG KIT #6-1368 (for Model 8245)
HARDWARE BAG KIT #6-1366 (for Model 8265)
HARDWARE BAG KIT #6-1365
PART NO. DESCRIPTION
1-3865 BOLT, 5/16-18 x 5/8" Shear (2)
9-1298 NUT, 5/16-18 Hex Nyloc (2)
2-8223 CABLE, Auger/Clutch
9-0001 BOLT, 5/16-18 x 3/4" Short Neck
Carriage (2)
9-0187 WASHER, 5/16 Split Lock (2)
9-0196 NUT, 5/16-18 Hex (2)
9-0041 PIN, 1/8 x 1” Cotter
9-1082 PIN, 3/32 x 3/4” Cotter
9-1550 BOLT, 5/16-18 x 1-7/8" Shear (2)
1-2080 TIE, Cable 7” (2)
25
*9-0196 HEX NUT (2)
*9-0187 LOCK WASHER (2)
ACCESSORIES (continued)
DRIFT CUTTER KIT #6-0472
3-7971 DRIFT CUTTER
*9-0001 CARRIAGE
BOLT (2)
*INCLUDED IN 6-0502 HARDWARE
BAG (PART OF THIS KIT)
TIRE CHAIN KITS FOR SNOW HOG TIRES
MODELS
8245, 8265
9265 & E9265
MODELS
10305, 10305E
E10305, E10305E
11305 & E11305
LARGE FRAME SNOWTHROWER MANUAL No.06037
TIRE SIZE
16-4.80 x 8
TIRE SIZE
16-6.50 x 8
KIT NO.
6-0900*
KIT NO.
6-0927*
*Each Kit Includes
Two (2) Chains
26
ACCESSORIES (Continued)
ELECTRIC START KITS
6-0759, KIT, 120 Volt Electric Start for Tecumseh HMSK 8 & 10 HP Engines
(Tecumseh Kit No. 179-84C)
For use on USA Models 8245, 9265 and 10305
6-3109, KIT, 230 Volt Electric Start for Tecumseh HMSK 8, 9 & 10 HP Engines
Includes 7-2610 Electric Starter Kit (Tecumseh No. 179-160) and
7-2611, 8’ Extension Cord
For use on Euro Models: E9265 & E10305
LIGHT KIT
6-1191, KIT, Light (for engines built with 18 watt internal alternator)
For use on Models 8265, E8265, 9265, E9265, 10305, 10305E, E10305 and E10305E)
SINGLE HANDLE CONTROL KIT
6-0991, KIT, Single Handle Control Retro-Fit
Fits Large Frame Snow Throwers After Models 8242, 8262 & 10302
REMOTE DEFLECTOR CONTROL KIT
6-1014, KIT, Remote Deflector Control
ACCESSORY LUBRICATION
Part No. 2-9577 GREASE, Benalene 900
MANUAL No. 06037 LARGE FRAME SNOWTHROWER
27
Parts Manual for
TWO STAGE
LARGE FRAME
SNOW THROWER
SERIES 5
MODELS
8245
8265
E8265
9265
E9265
10305
11305
10305E
E10305
E10305E
E11305
IT IS THE POLICY O F SNAPPER TO IMPRO VE ITS PRO DUCTS WHENEVER IT IS POSSIBL E
AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH
CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
COPYRIGHT © 2000
SNAPPER INC.
ALL RIGHTS RESERVED
MANUAL No. 06037 (Rev. 5, 7/03/00) Printed in U.S.A.
28
Loading...