Parts Manual fo
r
)
)
INTERMEDIATE REAR TINE TILLER
6 & 7 HP 16" TWO SPEED
MODEL
6016RT (7800052
7016RT (7800053
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Revision 2,
McDonough, GA, 30253 U.S.A.
10/11/2006
Manual No. 7006257
TP 400-5131-2-RT-N
s
PAGE GROUP
4
6
10
14
16
18
20
22
24
Handle Bar Group
Engine, Belts & Wheels Group - 6 HP
Engine, Belts & Wheels Group - 7 HP
Transmission Group
Wheel & Tiller Shaft Group
Hood, Drag Stake & Tine Group - 6 HP
Hood, Drag Stake & Tine Group - 7 HP
Decal Group
Hiller/Furrower Attachment
Table Of Content
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
3
TP 400-5131-2-RT-N
Handle Bar Group
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
4
Handle Bar Group
p
y
Part No Descri
1 1716699 2 HANDLE GRIP, Drive Control Lever
2 1722325 1 LEVER, Drive Control
3 1719038 2 HANDLE GRIP
4 1960392 4 SCREW, Pan Head Phillips #10-24 x 1/2
5 1716723 1 BRACKET, Drive Control Lever LH
6 1933896 6 NUT, Hex Nylock, 10-24
7 1716720 1 SPRING, Forward Cable Adjustment
8 2820438 4 NUT, Hex Jam, 5/16-24
9 1723692 1 HANDLE BAR ASSEMBLY
10 1719037 2 CABLE ASSEMBLY
11 1719063 2 C-CLAMP
12 1921332 3 CAPSCREW, Hex Head, 5/16-18 x 3/4
13 1723703 1 PIN, Detent
14 1723695 1 PIVOT ROD ASSEMBLY
15 1723696 1 PIVOT MOUNT ASSEMBLY
16 1921210 4 CAPSCREW, Hex Head, 3/8-16 x 1
17 1916950 5 NUT, Hex, 3/8-16
18 1924940 2 WASHER
19 1723694 1 PIVOT, Handle Bar Mount
20 1920415 1 CAPSCREW, Hex Head, 3/8-16 x 1-1/4
21 1716770 1 WASHER
22 1922648 1 CAPSCREW, Hex Head 3/8-16 x 4
23 1723697 1 PIVOT, Hnadle Bar Height Adjustment
24 1960044 2 WASHER
25 1716729 1 LINK, Reverse
26 1921977 1 CAPSCREW, Hex Head, 5/16-18 x 1-1/4
27 1716725 1 HANDLE, Reverse
28 1716704 1 BUSHING, Pivot, 5/16
29 1716722 1 BRACKET, Drive Control Lever RH
30 1935048 2 NUT, Hex Flange Tow Way Lock, 5/16-18
31 1921332 4 BOLT, Hex Flange Head, 5/16-18 x 3/4
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
5
TP 400-5131-2-RT-N
Engine, Belts & Wheels Group - 6 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
6
Engine, Belts & Wheels Group - 6 HP
p
y
Part No Descri
1 1722157 1 BRACKET, Engine
2 1723711 1 SPACER, Engine
3 1722158 1 PULLEY, Engine 2 Groove
4 1716770 1 WASHER
5 1917356 2 LOCKWASHER, Spring, 5/16
6 1921515 2 CAPSCREW, Hex Head, 5/16-24 x 3/4
7 2805850 2 KEY, PARALLEL PLN, 3/16 x 3/16 x 1-3/32
8 1960345 1 CAPSCREW, Hex Head, 3/8-24 x 2
9 1716728 2 YOKE, Cable
10 1722159 1 ARM, Pivot
11 1716702 2 PIN, Link Forward/Reverse
12 1722162 1 GUIDE, Belt Reverse
13 1924940 4 WASHER, 3/8
14 1716805 1 PULLEY, Idler Reverse
15 1916950 2 NUT, Hex Center Lock, 3/8-16
16 1716703 2 PIN, Cotter
17 1723710 1 BOLT, Flat Head, 5/16-24 x 1-1/2
18 1722160 1 PIVOT
19 1960044 3 WASHER, 5/16
20 1716766 1 V-BELT, Forward
21 1716802 2 SPRING, Idler Arm
22 1935048 3 NUT, Hex Flange Lock, 5/16-18
23 1921332 3 BOLT, Hex Flange Head, 5/16-18 x 3/4
24 1722161 1 GUIDE, Belt Forward
25 1722165 1 COVER, Belt
26 1722163 1 PULLEY, Transmission 2 Groove
27 1721525 1 WHEEL & TIRE ASSEMBLY TILLER, Left
28 1721524 1 WHEEL & TIRE ASSEMBLY TILLER, Right
29 1716776 2 PIN, Lock
30 1716803 1 PULLEY, Forward Idler
31 1722166 1 ARM, Idler Forward
32 1722168 1 SCREW, Hex Socket Shoulder, 5/16-18 x 3/8
33 1925690 1 CAPSCREW, Hex Head, 5/16-18 x 3-1/2
34 1722144 1 V-BELT, Reverse
35 1922127 4 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
36 1 ^ ENGINE, 6HP B&S INTEK, Model #126412-0023-E2
37 1721528 1 ^^ BUMPER, Guard (Optional)
tionItem Qt
Note
Footnotes:
^See your local Briggs & Stratton dealer for Parts & Service.
^^Bumper is not standard with the 6HP tiller, but it is an available option, order the bumper guard (Ref# 37), 4 nuts (Ref#
22) and 4 capscrews (Ref# 35).
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
7
TP 400-5131-2-RT-N
Engine, Belts & Wheels Group - 6 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
8
Engine, Belts & Wheels Group - 6 HP
p
y
Part No Descri
38 1919384 1 WASHER
39 2860164 1 WASHER
tionItem Qt
Note
Footnotes:
^See your local Briggs & Stratton dealer for Parts & Service.
^^Bumper is not standard with the 6HP tiller, but it is an available option, order the bumper guard (Ref# 37), 4 nuts (Ref#
22) and 4 capscrews (Ref# 35).
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
9
TP 400-5131-2-RT-N
Engine, Belts & Wheels Group - 7 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
10
Engine, Belts & Wheels Group - 7 HP
p
y
Part No Descri
1 1722157 1 BRACKET, Engine
2 1723711 1 SPACER, Engine
3 1722158 1 PULLEY, Engine 2 Groove
4 1716770 2 WASHER
5 1917356 2 LOCKWASHER, Spring 5/16
6 1921515 2 CAPSCREW, Hex Head, 5/16-24 x 3/4
7 2805850 2 KEY, Parallel
8 1960345 1 CAPSCREW, Hex Head, 3/8-24 x 2
9 1716728 2 YOKE, Cable
10 1722159 1 ARM, Pivot
11 1716702 2 PIN, LINK Forward/Reverse
12 1722162 1 GUIDE, Belt Reverse
13 1924940 4 WASHER, 3/8
14 1716805 1 PULLEY, Idler Reverse
15 1930651 2 NUT, Hex Center Lock, 3/8-16
16 1716703 2 PIN, Cotter
17 1723710 1 BOLT, Flat Head, 5/16-24 x 1-1/2
18 1722160 1 PIVOT
19 1960044 3 WASHER, 5/16
20 1716766 1 V-BELT, Forward
21 1716802 2 SPRING, Idler Arm
22 1935048 7 NUT, Hex Flange 5/16-18
23 1921332 3 BOLT, Hex Flange Head, 5/16-18 x 3/4
24 1722161 1 GUIDE, Belt Forward
25 1722165 1 COVER, Belt
26 1722163 1 PULLEY, Transmission 2 Groove
27 1716773 1 WHEEL & TIRE ASSEMBLY, Tiller LH
28 1716775 1 WHEEL & TIRE ASSEMBLY, Tiller RH
29 1716782 2 CAPSCREW, Hex Socket Head, 1/4-20 x 2-3/32
30 1960151 2 WASHER, 1/4
31 1716781 2 SPRING
32 1716778 2 PIN, Lock
33 2828372 2 NUT, Hex KEPS 1/4-20
34 1716777 1 KNOB, Lock Out Set of Two
35 1722185 2 SETSCREW, Wheel Lockout
36 1722171 2 CLAMP, C Wheel Lockout
37 1721528 1 BUMPER, Guard
tionItem Qt
Note
Footnotes:
^See your local Briggs & Stratton dealer for Parts & Service.
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
11
TP 400-5131-2-RT-N
Engine, Belts & Wheels Group - 7 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
12
Engine, Belts & Wheels Group - 7 HP
p
y
Part No Descri
38 1922127 8 CAPSCREW, Hex Head, 5/16-18 x 1-3/4
39 1722166 1 ARM, Idler Forward
40 1716803 1 PULLEY, Forward Idler
41 1722168 1 SCREW, Hex Socket Shoulder, 5/16-18 x 3/8
42 1925690 1 CAPSCREW, Hex Head, 5/16-18 x 3-1/2
43 1722144 1 V-BELT, Reverse
44 1 ^ ENGINE, 7HP B&S INTEK, Model #120412-0141-E1
45 1919384 1 WASHER, 3/8
46 2860164 1 WASHER
tionItem Qt
Note
Footnotes:
^See your local Briggs & Stratton dealer for Parts & Service.
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
13
TP 400-5131-2-RT-N
Transmission Group
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
14
Transmission Group
p
y
Part No Descri
1 1723700 1 DIPSTICK
2 1921332 12 CAPSCREW, Hex Head, 5/16-18 x 3/4
3 1722327 1 COVER PLATE & MOUNT
4 1716753 1 BRACKET, Engine Mount LH
5 1716752 1 BRACKET, Engine Mount RH
6 1935048 4 NUT, Hex Flange Lock, 5/16-18
7 1716789 2 GASKET, Housing & Transmission Cover
8 1716791 4 SEAL, Housing
9 1716792 2 GASKET, Bearing Cap Front/Rear
10 1716796 1 CAP, Rear Bearing
11 1716797 1 SEAL, Oil, Drive Shaft
12 1716798 3 BOLT, Hex Flange Head, 1/4-20 x 3/4
13 1716790 2 PLUG, Pipe, Socket Head, Oil Check, 1/4-18
14 1722330 1 TRANSMISSION, Housing, Tiller Casting
15 1716793 1 CAP, Rear Bearing
16 1716795 3 BOLT, Hex Flange Head, 1/4-20 x 7/8
17 1721511 1 BRACKET, Depth Regulator RT
18 1716799 1 GASKET KIT, Oil Seal ( Includes Ref. 7, 8, 9, and 11)
19 1723699 1 TRANSMISSION ASSEMBLY, Complete, w/Lockouts - 6 HP
19 1723701 TRANSMISSION ASSEMBLY, Complete - 7 HP
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
15
TP 400-5131-2-RT-N
Wheel & Tiller Shaft Group
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
16
Wheel & Tiller Shaft Group
p
y
Part No Descri
1 1716793 1 CAP, Rear Bearing
2 1716825 1 SHIM SET, Rear Bearing Cap
2 1716826 1 SHIM, 0.062 THK1-3/4” x OD1806 (As Required)
2 1716827 1 SHIM, 0.030 THK1-3/4” x OD1807 (As Required)
2 1716828 1 SHIM, 0.015 THK1-3/4” x OD1808 (As Required)
2 1716829 1 SHIM, 0.010 THK1-3/4” x OD1809 (As Required)
3 1716810 2 BEARING, Tapered (Cone & Race)
4 1716824 4 SPACER, 1” x 1-1/4”
5 1716816 4 BUSHING
6 1716815 4 SHIM SET, Axle Spacer
6 1716817 1 SHIM, 0.062 THK1-3/8” x OD1705 (As Required)
6 1716818 1 SHIM, 0.030 THK1-3/8” x OD1706 (As Required)
6 1716819 1 SHIM, 0.015 THK1-3/8” x OD1707 (As Required)
6 1716820 1 SHIM, 0.010 THK1-3/8” x OD1708 (As Required)
7 1716830 4 RING, Snap, Internal Retainer
8 1716791 4 SEAL, Housing
9 1716821 2 RING, Snap, External Retainer
10 1722333 1 DRIVE SHAFT, Main
11 1716813 2 KEY, Parallel Plane 1/4” x 1/4” x 1”
12 1716814 1 GEAR, Worm, Wheels Shaft
13 1716811 1 SHAFT ASSEMBLY, Wheels w/Lock Pin
13 1716812 1 SHAFT ASSEMBLY, Wheel w/Lock Pin
14 1716796 1 CAP, Rear Bearing
15 1716797 1 SEAL, Oil, Drive Shaft
16 2860164 1 WASHER, 5/8
17 1716811 1 SHAFT ASSEMBLY, Wheels w/Lock Pin
18 1716823 1 GEAR, Worm Shaft
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
17
TP 400-5131-2-RT-N
Hood, Drag Stake & Tine Group - 6 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
18
Hood, Drag Stake & Tine Group - 6 HP
p
y
Part No Descri
1 1723703 1 PIN, Detent, 5/16
2 1723702 1 LEVER, Depth Regulator
3 1921958 2 CAPSCREW, Hex Head, 1/4 - 20 x 1/2
4 1722329 1 HOOD, Tiller, No Decal
5 1917356 2 LOCKWASHER, Spring, 5/16
6 1920787 2 CAPSCREW, Hex Head, 5/16-18 x 1/2
7 1921971 2 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
8 1721513 1 TINE ASSEMBLY, LH
9 1916965 2 LOCKWASHER, Spring, 3/8
10 1930651 2 NUT, Hex Center Lock, 3/8-16
11 1935048 2 NUT, Hex Flange, 5/16-18
12 1721514 1 TINE ASSEMBLY, RH
13 1716701 2 BOLT, Hex Flange Head, 5/16-18 x 1/2
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
19
TP 400-5131-2-RT-N
Hood, Drag Stake & Tine Group - 7 HP
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
20
Hood, Drag Stake & Tine Group - 7 HP
p
y
Part No Descri
1 1723703 1 PIN, DETENT 5/16
2 1723705 1 LEVER, Depth Regulator
3 1921958 2 CAPSCREW, Hex Head, 1/4-20 x 1/2
4 1722329 1 HOOD, Tiller, No Decal
5 1917356 2 LOCKWASHER, 5/16
6 1920787 2 CAPSCREW, Hex Head, 5/16-18 x 1/2
7 1921210 16 CAPSCREW, Hex Head, 3/8-16 x 1
8 1716741 2 HOLDER, Tine Blade Left and Right
9 1921971 2 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
10 1916965 18 LOCKWASHER, 3/8
11 1930651 18 NUT, Hex Centerlock, 3/8-16
12 1716739 8 TINE BLADE, Left Side
13 1716737 8 TINE BLADE, Right Side
14 1716701 2 BOLT, Hex Flange Head, 5/16-18 x 1/2
15 1716749 1 REPL KIT, Tine Blade Holder (Includes Reference Nos. 7, 8, 9,
10, 11, 12, and 13)
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
21
TP 400-5131-2-RT-N
Decal Group
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
22
Decal Group
p
y
Part No Descri
1 1726721 1 DECAL, Snapper
2 1716734 1 DECAL, Console Forward/Reverse Instructions
3 1716747 1 DECAL, Hood, Operator Instructions Label
4 1716840 1 DECAL, Danger, Tine Hood Label
5 1723523 2 DECAL, 6016 RT (not shown)
5 1723522 2 DECAL, 7016 RT
6 1716800 1 DECAL, Warning, Belt Cover
7 1716839 1 DECAL, Brush Bar (on 7 HP model only)
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
23
TP 400-5131-2-RT-N
Hiller/Furrower Attachment
Manual No. 7006257 INTERMEDIATE REAR TINE TILLER
TP 400-5131-2-RT-N
24
Hiller/Furrower Attachment
p
y
Part No Descri
1 1931352 2 BOLT, Carriage, 3/8-16 x 1-1/2
2 1931333 4 BOLT, Carriage, 5/16-18 x 3/4
3 1723726 1 HILLER WING, Left
3 1723727 1 HILLER WING, Right (Not Shown)
4 1960044 4 WASHER, Flat, 5/16
5 2820426 4 LOCKWASHER, External Tooth, 5/16
6 1933126 4 WING NUT, 5/16-18
7 1960268 1 BOLT, Socket Head, 3/8-16 x 1-1/4
8 1723725 1 BRACKET
9 1919439 2 NUT, Nylock, 3/8-16
10 1916950 1 NUT, Hex, 3/8-16
11 1723724 1 BLADE, Furrower
12 1686802 1 HILLER / FURROWER ATTACHMENT, Complete
tionItem Qt
Note
Footnotes:
Manual No. 7006257INTERMEDIATE REAR TINE TILLER
25
TP 400-5131-2-RT-N
Parts Manual fo
r
INTERMEDIATE REAR TINE TILLER
6 & 7 HP 16" TWO SPEED
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
Manual No. 7006257
Revision 2,
10/11/2006
TP 400-5131-2-RT-N
Loading...