Snapper 4808 User Manual

Attachment
g
Illustrated
Parts List
Attachment
. No. Description
Mf
1695419 Tiller 36"
500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.2007
Part No.:
TP 400-4808-00-AT-SMA
Rev.
1723861 11/2007
Table Of Content
s
PRODUCT COMPONENTS PAGES
Drive Group ..........................................................................................................................................................
Housing Group .....................................................................................................................................................
Lift Group ..............................................................................................................................................................
Tine & Deflector Group ........................................................................................................................................
10 12
Torque Specification Chart ..................................................................... Inside Back Cover
4 8
Drive Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
987907
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
4
TP 400-4808-00-AT-SMA
Drive Group
PART NO. DESCRIPTIONREF NO QTY.
Footnotes
PIN, Round Head Drilled, 3/8 x 2 1 2118053SM 1 LIFT ASSEMBLY 2 1707569ASM 1 PIN, Spring Retainer 3 2176012SM 5 CAPSCREW, Hex Head, 7/16-14 x 1-1/4, Black 4 2823471SM 1 WASHER, 7/16 5 1925125SM 2 SPACER 6 2105346SM 2 NUT, Hex Flange Lock, 7/16-14, Black 7 1930650SM 2 CAPSCREW, Hex Head, 5/16-18 x 2-3/4, Balck 8 1923141SM 1 SUPPORT, Rear Belt Guard 9 2105359ASM 2 SPACER 10 1704716SM 2 ANCHOR, Spring 11 1707599SM 1 SPACER 12 2105339ASM 1 SPRING, Torsion 13 1707593SM 1 WASHER, Special, Nylon 14 2860171SM 1 BUSHING, .343" x .750" x 1.060" 15 1666106SM 1 WASHER, 5/16, Black 16 1919326SM 1 COVER, Belt 17 1707564ASM 1 ROD 18 1657562SM 1 CAPSCREW, Hex Head, 7/16-14 x 3-1/2, G8 19 1930585SM 1 ARM & HUB ASSEMBLY 20 2105295ASM 1 LOCKWASHER, 3/8, Black 21 1916965SM 6 NUT, Hex, 3/8-16, Black 22 1960687SM 3 WASHER, 3/8, Black 23 1924940SM 2 SPACER 24 1709923SM 1 GUARD, Spring 25 1708352ASM 3 SCREW, Set Square Head, Cup Point, 3/8-16 x 1/2 26 1960474SM 1 PULLEY, 7.96" OD x .752" ID, w/.562" GROOVE, w/HUB 27 1723854SM 1 KEY, Parellel 28 2157427SM 1 PULLEY, Idler, 2.75" OD x .377" ID x .87 WD 29 1721133SM 1 CAPSCREW, Hex Head, 3/8-16 x 3-1/2, Black 30 1923938SM 1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4, Black 31 1921971SM 2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, Black 32 1920415SM 1 PULLEY, Idler, 4" OD x .375" ID x .83" WD 33 1706510SM 1 PULLEY, Idler, 1.875" OD x .375" ID x .97" WD 34 1706511SM 2 V-BELT,167.40" Long 35 1723478SM 1 SHAFT & SUPPORT ASSEMBLY 36 1708961ASM 1 PIN, Round Head Drilled, 3/8 x 1, Black 37 1708298SM 1 ARM ASSEMBLY, Tiller Idler 38 1735064ASM 1 CAPSCREW, Hex Head, .375-16 x 2-1/4 39 1922130SM 2 WASHER, 3/8, Black 40 1922755SM 3 PULLEY, Idler, 4.00" OD x .669" ID x 1WD, w/Bearing 41 1724387SM 1 PULLEY, 3" OD x .378" ID x .75" WD, w/Bearing 43 1721134SM 1 PIN, Round Head Drilled, 7/16 x 1-3/4 44 2155037SM 2 FRAME ASSEMBLY 45 1651844ASM 1
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
5
TP 400-4808-00-AT-SMA
Drive Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
987907
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
6
TP 400-4808-00-AT-SMA
Drive Group
PART NO. DESCRIPTIONREF NO QTY.
CAPSCREW, Hex Head, 1/2-13 x 5, G8 Black 46 1926159SM 1 WASHER, 1/2, Black 47 1924361SM 4 SPACER 48 2105386SM 2 NUT, Hex Flange Lock, 1/2-13, Black 49 1930644SM 1 NUT, Hex, 5/16-18, Black 50 1917372SM 1 LOCKWASHER, 5/16, Black 51 1917356SM 1 ROD, Diff Lock, 15" Long 52 1735052SM 1 SPACER 53 1667812SM 1 NUT, Flange, ESNA, 3/8-16 54 1960687SM 2 CAPSCREW, 3/8-16 x 2-1/2 55 1921972SM 1 SPACER 56 1706644SM 1 NUT, Flange, 3/8-16 57 1928352SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
7
TP 400-4808-00-AT-SMA
Housing Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
984364
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
8
TP 400-4808-00-AT-SMA
Housing Group
PART NO. DESCRIPTIONREF NO QTY.
3 1650841SM 1
CHAIN, # 40 1 2105336SM 2 CHAIN, # 50 2 2178174SM 1 TRANSMISSION SUB ASSEMBLY (Incl. Ref. Nos. 1-16, 18-38 on this page) & Incls. Ref.
Nos. 1-5,7,11,17,18,19,34,36 & 38 in the 36" Tiller Drive Group) FITTING, Grease 4 2815019SM 2 BOLT, Hex Head, Drilled & Tapped 5 2105132SM 2 LOCKWASHER, 1/2 6 1916966SM 4 BAR, Side 7 2105320ASM 2 NUT, Hex, 5/16-1 8 1917372SM 4 LOCKWASHER, 5/16 9 1917356SM 4 BEARING 10 1669337SM 2 LOCKNUT, 5/16-18 11 1923362SM 13 CASE ASSEMBLY, Half, R.H. 12 2105366ASM 1 SEAL 13 2105365SM 2 PLATE ASSEMBLY, Upper Bearing 14 1669338SM 2 RING, Retaining 15 2827320SM 4 WASHER, 1 16 2860208SM 4 SPACER, Inter. 18 2105192SM 1 SHAFT ASSEMBLY, Pulley 19 2105298SM 1 SPROCKET & BEARING ASSEMBLY, (Incl. Ref. Nos. 17 & 21) 20 1650975SM 1 SPROCKET & BEARING ASSEMBLY, (Incl. Ref. Nos. 17 & 24) 25 1650976SM 1 BEARING, Roller 17 2105195SM 4 SPROCKET ASSEMBLY, (See Ref. No. 20) 21 * 1 SPACER 22 2105360SM 2 SHAFT ASSEMBLY, Tine 23 2178177SM 1 SPROCKET (See Ref. No. 25) 24 * 1 SPACER, Internal 26 2105292SM 1 LOCKNUT, Hex, Jam, 3/8-16 27 1930645SM 6 PLATE ASSEMBLY 28 1669298SM 2 SEAL 29 2105357SM 2 BEARING 30 2105309SM 2 CAP, Grease 31 2105363SM 2 LOCKNUT, Flange, 1/2-13 32 1930644SM 2 CASE ASSEMBLY, Half, L.H. 33 2105367ASM 1 CAPSCREW, Hex Head, 5/16-18 x 5/8 34 1925205SM 13 WASHER, 1/2 35 1918431SM 1 CAPSCREW, Hex Head, 1/2-13 x 4 36 1926158SM 1 CAPSCREW, Hex Head, 1/2-20 x 1 37 1929528SM 2 GASKET 38 2105373SM 1 CAPSCREW, Hex Head, 5/16-1 8 x 1-1 /4 39 1921977SM 1 WASHER, 3/8 40 1924940SM 2 LOCKNUT, Flange, 5/16-18 41 1935048SM 2 HOOK, "S" 42 1679204SM 1
Footnotes
Note* Not a servicable part.
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
9
TP 400-4808-00-AT-SMA
Lift Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
986147
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
10
TP 400-4808-00-AT-SMA
Lift Group
PART NO. DESCRIPTIONREF NO QTY.
NUT, Hex Lock ESNA, 1/2-13 1 1960355SM 7 WASHER, 1/2 2 1926192SM 2 SPRING, Compression 3 2171011SM 1 SPACER, .52" x .738" 4 1668662SM 2 RETAINER, Pin 5 2176012SM 2 LEVER ASSEMBLY, Rear Hitch 6 1723790ASM 1 PIN, Round Head Drilled, 3/8 x 2-3/8 7 2105249SM 1 NUT, Hex, 1/2-13 8 1916951SM 2 PIN, Yoke, Drilled, 5/8 x 1-13/16 9 1960038SM 1 CARRIAGE BOLT, 3/8-16 x 1 10 1931350SM 1 CRANK & WASHER ASSEMBLY 11 1723840ASM 1 BRACKET 12 1723841ASM 1 NUT, Hex Lock ESNA, 3/8-16 13 1919439SM 4 SPRING, Extension 14 1723412SM 1 ROD & TUBE ASSEMBLY 15 1686941SM 1 HITCH ASSEMBLY 16 1723107ASM 1 SPACER 17 1709235SM 4 WASHER, 1/2 18 1924361SM 4 CAPSCREW, Hex Head, 1/2-13 x 2 19 1921024SM 4 CAPSCREW, Hex Head, 1/2-13 x 1-1/2 20 1920328SM 2 CAPSCREW, Hex Head, 1/2-13 x 1-1/4 21 1921977SM 2 WASHER, 1/2 22 1960170SM 4 HITCH ASSEMBLY 23 1707470ASM 1 DRAWBAR & WASHER ASSEMBLY 24 1722608ASM 1 NUT, Hex Lock ESNA, 5/16-18 25 1919438SM 2 CAPSCREW, Hex Head, 5/16-18 x 1, G8 26 1926149SM 2 BAR, Lift Link 27 1723795ASM 1 CAPSCREW, Hex Head, 3/8-16 x 1 28 1921210SM 4 NUT, Hex Whiz Lock, 5/16 29 1927557SM 2 NUT, Hex Centerlock Jam, 1/2-13 30 1924650SM 1 NUT, Hex Flange, 1/2-13 31 1960515SM 1 CAPSCREW, Hex Hed, 5/16-18 x 1 32 1921333SM 1 BRACKET 33 1723842ASM 1 ROD, Threaded 34 1723844SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
11
TP 400-4808-00-AT-SMA
Tine & Deflector Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
984363
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
12
TP 400-4808-00-AT-SMA
Tine & Deflector Group
PART NO. DESCRIPTIONREF NO QTY.
PLATE, End, R.H. 1 1707990ASM 1 LOCKNUT, Flange, 5/16-18 2 1927557SM 15 CARRIAGE BOLT, 5/16-18 x 5/8 3 1931332SM 8 DEFLECTOR ASSEMBLY, R.H. 4 2105369ASM 1 DECAL, Safety 5 1679700SM 2 SHIELD 6 2105354ASM 1 NUT, Hex Head, Flange, 1/4-20 7 1930642SM 1 CHANNEL 8 1707938ASM 1 CAPSCREW, Hex Head, 3/8-16 x 1 9 1921210SM 2 WASHER 10 1960353SM 2 NUT, Hex, Flange, 3/8-16 11 1930645SM 2 KEY 12 2105337SM 4 SCREW, Hex, Whizlock, 3/8-16 x 3/4 13 1933260SM 2 PLATE, End, L.H. 14 1707991ASM 1 DEFLECTOR ASSEMBLY, L.H. 15 2105370ASM 1 CAPSCREW, Hex, Whizlock, 3/8-16 x 1 16 1934654SM 4 LOCKNUT, 7/16-20 17 1928867SM 16 BLADE, Tine, R.H. 18 2105376ASM 8 BLADE, Tine, L.H. 19 2105375ASM 8 HUB & PLATE ASSEMBLY 20 1651504ASM 2 CAPSCREW, Hex Head, 7/16-20 x 1-1/2 21 1920353SM 16 PIN 22 2105249SM 2 PIN, Cotter 23 1918451SM 2 BLADE ASSEMBLY, L.H. 24 1650461SM 1 BLADE ASSEMBLY, R.H. 25 1650460SM 1 DEFLECTOR 26 1707945A 1 ROD 27 1707939SM 1 PIN, Cotter 28 1918448SM 1 CHAIN 29 1707951A 1 CAPSCREW, Hex Head, 1/4-20 x 7/8 30 1924009SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1695419 - Tiller 36"
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
13
TP 400-4808-00-AT-SMA
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
Hardware Identification & Torque Specifications
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside Diameter
Nut, 1/2”
No
Marks
3/8” Bolt or Nut
Wrench—9/16”
3/8
5/16” Bolt or Nut
Wrench—1/2”
5/16
1/4” Bolt or Nut
Wrench—7/16”
1/4
1/2” Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16 DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Common Hardware Types
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware Grade
Size Of
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the second number represents the example, and the final number is the bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
body length
(16 in this
of the
The guides and ruler furnished below are designed to help you select the appropriate hardware and tools.
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 11 15.0 17 23.1 25 34.0 5/16-24 12 16.3 19 25.8 27 34.0 3/8-16 20 27.2 30 40.8 45 61.2 3/8-24 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/16-20 35 47.6 55 74.8 80 108.8 1/2-13 50 68.0 75 102.0 110 149.6 1/2-20 55 74.8 90 122.4 120 163.2 9/16-12 65 88.4 110 149.6 150 204.0 9/16-18 75 102.0 120 163.2 170 231.2 5/8-11 90 122.4 150 204.0 220 299.2 5/8-18 100 136 180 244.8 240 326.4 3/4-10 160 217.6 260 353.6 386 525.0 3/4-16 180 244.8 300 408.0 420 571.2 7/8-9 140 190.4 400 544.0 600 816.0 7/8-14 155 210.8 440 598.4 660 897.6 1-8 220 299.2 580 788.8 900 1,244.0 1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5 b. for flange whizlock nuts and screws - use 135% of
3. Unless otherwise noted on assembly drawings, all torque values must meet this specification.
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
2.1
20
2.3
27
3.1
31
3.5
66
7.6 8 10.9 12 16.3
76
8.6 10 13.6 14 19.0
torques. grade 5 torques.
30 31 43 49
NOTES
in/lbs
3.4
3.5
4.9
5.5
41 43 60 68
4.6
4.9
6.8
7.7
Loading...