Snapper 4582 User Manual

Attachment
g
Illustrated
Parts List
Attachment
. No. Description
Mf
1695196 Hitch Sub Frame
500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.2007
Part No.:
TP 400-4582-00-AT-SMA
Rev.
1734888
04/2007
Table Of Content
s
PRODUCT COMPONENTS PAGES
Hitch Group ..........................................................................................................................................................
Torque Specification Chart ..................................................................... Inside Back Cover
4
Hitch Group
NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
987583
The above parts group applies to the following Mfg. Nos.:
1695196 - Hitch Sub Frame
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
4
TP 400-4582-00-AT-SMA
Hitch Group
PART NO. DESCRIPTIONREF NO QTY.
PUSH BAR ASSEMBLY, Hitch Sub Frame 1 1733779ASM 1 ROD, Hitch 2 1733812SM 1 RETAINER, Pin Spring 3 2176012SM 5 SHAFT & HOOK ASSEMBLY 4 1723292SM 1 CLAMP, Wheel Support for 3/4 Shaft 5 1653768SM 1 SPRING, Compression 6 2171011SM 1 CARRIAGE BOLT, 5/16-18 x 1 G5 7 1931335SM 4 WASHER, 5/16 8 1919381SM 4 LOCKWASHER, Spring 5/16 9 1917356SM 4 NUT, Hex 5/16-18 10 1917372SM 4 LEVER ASSEMBLY, Lift Snow Attach 11 1724025SM 1 PIN, Round Head Drilled 3/8 x 2-3/8 12 2105249SM 1 PLATE, Presser Lock 13 1722469SM 1 PIN, Flat Head Drilled 14 1722819SM 1 CLIP, Hair Pin 1/8 Diameter Spring 15 1960033SM 1 ROD, Rear Lift 16 1722946SM 1 COLLAR, Set 17 1729258SM 2 SCREW, Set, Square Head Cup Point 5/16-18 x 1/2 G8 18 1928721SM 2 TUBE & PIN ASSEMBLY, Guide 19 1723115SM 1 ROD, Hitch 20 1723309SM 1 BAR, Lift, 8-15/16 Long 21 1723795ASM 1 CLIP, Hair Pin 22 1960074SM 2 CAPSCREW, Hex Head 3/8-16 x 1 G5 23 1921210SM 4 NUT, Hex Flange 3/8-16 Whiz Lock 24 1928352SM 4 LATCH, Push Bar 25 1733814ASM 1 ROD, Mower Hitch 26 1734050SM 1
Footnotes
The above parts group applies to the following Mfg. Nos.:
1695196 - Hitch Sub Frame
Briggs and Stratton Yard Power Products Group
2007Copyright © by Briggs and Stratton Corporation
Milwaukee, WI, USA. All rights reserved
5
TP 400-4582-00-AT-SMA
Hardware Identification & Torque Specifications
Common Hardware Types
Hex Head Capscrew
Carriage Bolt
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size
second number is present it represent the
When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the second number represents the example, and the final number is the bolt or screw (in this example 2 inches long).
, meaning the
Nominal size
inside diameter
, or
body diameter
threads per inch
body length
Washer
Lockwasher
Hex Nut
is 1/2 inch; if a
threads per inch
is 1/2 inch; the
(16 in this
of the
The guides and ruler furnished below are designed to help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
Nut, 1/2”
Inside Diameter
1
1/4 3/4
1/2
Screw, 1/2 x 2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Body
Diameter
Body
Length
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware Grade
Size Of Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 11 15.0 17 23.1 25 34.0 5/16-24 12 16.3 19 25.8 27 34.0 3/8-16 20 27.2 30 40.8 45 61.2 3/8-24 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/16-20 35 47.6 55 74.8 80 108.8 1/2-13 50 68.0 75 102.0 110 149.6 1/2-20 55 74.8 90 122.4 120 163.2 9/16-12 65 88.4 110 149.6 150 204.0 9/16-18 75 102.0 120 163.2 170 231.2 5/8-11 90 122.4 150 204.0 220 299.2 5/8-18 100 136 180 244.8 240 326.4 3/4-10 160 217.6 260 353.6 386 525.0 3/4-16 180 244.8 300 408.0 7/8-9 140 190.4 400 544.0 600 816.0 7/8-14 155 210.8 440 598.4 660 897.6 1-8 220 299.2 580 788.8 900 1,244.0 1-12 240 326.4 640 870.4 1,000 1,360.0
1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque values must meet this specification.
No
Marks
SAE Grade 2 SAE Grade 5 SAE Grade 8
in/lbs in/lbs
19
2.1
20
2.3
27
3.1
31
3.5
66
7.6 8 10.9 12 16.3
76
8.6 10 13.6 14 19.0
30 31 43 49
NOTES
3.4
3.5
4.9
5.5
in/lbs
41 43 60 68
420 571.2
4.6
4.9
6.8
7.7
Wrench & Fastener Size Guide
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16
5/16” Bolt or Nut
Wrench—1/2”
3/8
3/8” Bolt or Nut
Wrench—9/16”
7/16 DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”
Loading...