Snapper 3011523BV User Manual
Safety Instructions & Operator's Manual for
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for
further details.
Manual No. 7102295 (I.R. 2/18/2008)
TP 100-5350-IR-RE-N
REAR ENGINE RIDING MOWER
SERIES 23
Models
2811523BV (7800102)
2812523BVE (7800104)
3011523BV (7800103)
3012523BVE (7800105)
3317523BVE (7800254)
C2811523BV (7800363)
C2812523BVE (7800365)
C3011523BV (7800364)
C3012523BVE (7800366)
C3317523BVE (7800368)
Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your
confidence in the Snapper brand. When operated and maintained according to the instructions in this
manual, your Snapper product will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with the
machine and how to avoid them. This machine is designed and intended only for finish cutting of
established lawns and is not intended for any other purpose. It is important that you read and understand
these instructions thoroughly before attempting to start or operate this equipment. Save these
instructions for future reference.
PRODUCT REGISTRATION
IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS
(Complete the following information on your Snapper purchase)
Date of Purchase__________________________________________________________________
Retailer_________________________________________________________________________
Retailer's Phone Number___________________________________________________________
Equipment
Model Number______________________________________________________________
Serial Number ______________________________________________________________
Engine
Model_________________________Type__________________Trim___________________
It is very important that you register your purchase with Snapper to ensure warranty coverage. Please
mail your product registration card to:
Snapper at P.O. Box 1379, McDonough, Georgia 30253.
Or you may register online at www.snapper.com.
You can contact us at our website, or if you would like to speak with a Customer Service
Representative, call us at the Snapper Customer Relations Center at 1-800-935-2967. For faster
service please have your Serial Number and Model Number available.
Briggs & Stratton Yard Power Products Group
Copyright © 2008, Briggs & Stratton Corporation
Milwaukee, WI, USA. All Rights Reserved.
SNAPPER is a trademark of
Simplicity Manufacturing, Inc.
Port Washington, WI, USA.
1
Operator Safety
Features and Controls Operation Maintenance Troubleshooting Warranties
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operator Seat Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Engaging Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Engaging Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Stopping Engine, Wheel Drive, Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setting Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Reverse Lockout Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Service - After the First 5 Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Service - Every 25 Operating Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Service - Annually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Service - Every Two Years . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Removing the Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Engine Adjustments and Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Mower Deck and Component Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Rear Engine Rider Drive Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Mower Drive Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Snapper Rear Engine Rider Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Maintenance/Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
WARNING
Battery posts, terminals and related accessories contain
lead and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
!
!
WARNING
Engine exhaust, some of its constituents, and certain
vehicle components contain or emit chemicals known to
the State of California to cause cancer or other reproductive
harm.
!
!
www.snapper.com2
Operator Safety
! !
WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects
that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in
serious injury or death to the operator or other persons. The owner of the machine must understand these
instructions and must allow only persons who understand these instructions to operate machine. Each
person operating the machine must be of sound mind and body and must not be under the influence of any
substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your
machine which your dealer cannot answer to your satisfaction, call or write the Customer Service
Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).
Protection for Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Children who have been
given rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over by the
machine. Never assume that children will remain where you
last saw them.
1. KEEP children out of the mowing area and under the
watchful care of a responsible adult other than the operator.
2. DO NOT allow children in yard when machine is operated
(even with the blade OFF).
3. DO NOT allow children or others to ride on machine,
attachments or towed equipment (even with the blades
OFF). They may fall and be seriously injured.
4. DO NOT allow pre-teenage children to operate machine.
5. ALLOW only responsible adults & teenagers with mature
judgment under close adult supervision to operate machine.
6. DO NOT operate blades in reverse. STOP BLADES. LOOK
and SEE behind and down for children, pets and hazards
before and while backing.
7. USE EXTRA CARE when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
Protection against Tipovers
Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death.
All slopes require extra CAUTION. If you cannot back up the
slope or if you feel uneasy on the slope, DO NOT mow it.
Use extra care with grass catchers or other attachments;
these affect the handling and the stability of the machine.
Refer to the Slope Guide at the end of this manual.
1. DO NOT operate machine on slopes exceeding 15
degrees (27% grade).
2. Exercise EXTREME CAUTION on slopes above 10
degrees (18% grade). Turn blades OFF when traveling
uphill. Use a slow speed and avoid sudden or sharp turns.
3. DO NOT operate machine back and forth across face of
slopes. Operate up and down. Practice on slopes with
blades off.
4. AVOID starting, stopping or turning on slopes. If machine
stops going uphill or tires lose traction, turn blades OFF and
back slowly straight down the slope.
5. STAY ALERT for holes and other hidden hazards. Tall
grass can hide obstacles. Keep away from ditches,
washouts, culverts, fences and protruding objects.
Protection against Tipovers
(Continued From Previous Column)
6. KEEP A SAFE DISTANCE (at least 3 feet) away from edge
of ditches and other drop offs. The machine could turn over
if an edge caves in.
7. Always begin forward motion slowly and with caution.
8. Use weights or a weighted load carrier in accordance
with instructions supplied with a grass catcher. DO NOT
operate machine on slopes exceeding 10 degrees (18%
grade) when equipped with grass catcher.
9. DO NOT put your foot on the ground to try to stabilize
the machine.
10. DO NOT operate machine on wet grass. Reduced traction could cause sliding.
11. Choose a low enough speed setting so that you will not
have to stop or shift on a slope. Tires may lose traction on
slopes even though the brakes are functioning properly.
12. DO NOT operate machine under any condition where
traction, steering or stability is doubtful.
13. Always keep the machine in gear when going down
slopes. DO NOT shift to neutral (or actuate hydro roll
release) and coast downhill.
Preparation
1. Read, understand, and follow instructions and warnings
in this manual and on the machine, engine and attachments. Know the controls and the proper use of the
machine before starting.
2. Only mature, responsible persons shall operate the
machine and only after proper instruction.
3. Data indicates that operators age 60 and above, are
involved in a large percentage of mower-related injuries.
These operators should evaluate their ability to operate the
mower safely enough to protect themselves and others
from serious injury.
4. Handle fuel with extra care. Fuels are flammable and
vapors are explosive. Use only an approved fuel container.
DO NOT remove fuel cap or add fuel with engine running.
Add fuel outdoors only with engine stopped and cool. Clean
spilled fuel from machine. DO NOT smoke.
5. Practice operation of machine with BLADES OFF to learn
controls and develop skills.
6. Check the area to be mowed and remove all objects such
as toys, wire, rocks, limbs and other objects that could
cause injury if thrown by blade or interfere with mowing.
Important Operator Safety Instructions
3
Operator Safety
! !
Protection against Tipovers
(Continued From Previous Column)
7. Keep people and pets out of mowing area. Immediately
STOP blades, STOP engine, and STOP machine if anyone
enters the area.
8. Check shields, deflectors, switches, blade controls and
other safety devices frequently for proper operation and
location.
9. Make sure all safety decals are clearly legible. Replace if
damaged.
10. Protect yourself when mowing and wear safety glasses,
a dust mask, long pants and substantial footwear.
11. Know how to STOP blades and engine quickly in preparation for emergencies.
12. Use extra care when loading or unloading the machine
into a trailer or truck.
13. Check grass catcher components frequently for signs of
wear or deterioration and replace as needed to prevent
injury from thrown objects going through weak or worn
spots.
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
1. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
2. Use only an approved fuel container.
3. DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside where
there is an open flame, spark or pilot light such as on a
water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling.
7. Remove gas-powered equipment from the vehicle or
trailer and refuel it on the ground. If this is not possible,
then refuel equipment using a portable container, rather
than a gasoline dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed vehicles or trailers.
9. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. DO
NOT use a nozzle lock-open device
10. If fuel is spilled on clothing, change clothing immediately.
11. Never overfill a fuel tank. Replace fuel cap and tighten
securely.
Operation
1. Mount and dismount machine from left side. Keep clear
of discharge opening at all times.
2. Start engine from operator’s seat, if possible. Make sure
blades are OFF and parking brake is set.
3. DO NOT leave machine with engine running. STOP
engine, STOP blades, SET brake, and Remove key before
leaving operators position of any reason.
4. DO NOT operate machine unless properly seated with
feet on feet rests or pedal(s).
5. STOP BLADES and ENGINE and make sure blades have
stopped before removing grass catcher or unclogging
mower to prevent loss of fingers or hand.
6. Blades must be OFF except when cutting grass. Set
blades in highest position when mowing over rough
ground.
7. Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES
are ON or machine is in motion.
8. DO NOT operate machine without entire grass catcher or
guards in place and working. DO NOT point discharge at
people, passing cars, windows or doors.
9. Slow down before turning.
10. Watch out for traffic when near or crossing roadways.
11. STOP engine immediately after striking an obstruction.
Inspect machine and repair damage before resuming operation.
12. Operate machine only in daylight or with good artificial
light.
13. Move joystick (if equipped) SLOWLY to maintain control
during speed and directional changes.
14. Exercise CAUTION when pulling loads. Limit loads to
those you can safely control and attach loads to hitch plate
as specified with SNAPPER attachment instructions.
15. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control. When towing,
travel slowly and allow extra distance to stop.
16. DO NOT operate engine in enclosed areas. Engine
exhaust gases contain carbon monoxide, a deadly poison.
17. DO NOT discharge material against a wall or obstruction. Material may ricochet back towards the operator.
18. Only use accessories approved by the manufacturer.
See manufacturer’s instructions for proper operation and
installation of accessories.
Important Operator Safety Instructions (Continued)
www.snapper.com4
Operator Safety
! !
Towing
1. Tow only with a machine that has a hitch designed for
towing. DO NOT attach towed equipment except at the hitch
point.
2. Follow the manufacturer’s recommendation for weight
limits for towed equipment and towing on slopes.
3. DO NOT allow children or others on towed equipment.
4. On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.
5. Travel slowly and allow extra distance to stop.
Maintenance
1. DO NOT store machine or fuel container inside where
fumes may reach an open flame, spark or pilot light such as
in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an
enclosure. Store fuel container out of the reach of children
in a well ventilated, unoccupied building.
2. Keep engine free of grass, leaves or excess grease to
reduce fire hazard and engine overheating.
3. When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.
4. Check brakes frequently; adjust, repair or replace as
needed.
5. Keep all bolts, nuts and screws properly tight. Check that
all cotter pins are in proper position.
Maintenance
(Continued From Previous Column)
6. Always provide adequate ventilation when running
engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.
7. Disconnect negative (black) cable from battery before
performing maintenance or service. Cranking engine could
cause injury.
8. DO NOT work under machine without safety blocks.
9. Service engine and make adjustments only when engine
is stopped. Remove spark plug wire(s) from spark plug(s)
and secure wire(s) away from spark plug(s).
10. DO NOT change engine governor speed settings or
overspeed engine.
11. Lubricate machine at intervals specified in manual to
prevent controls from binding.
12. Mower blades are sharp and can cut. Wrap the blades
or wear heavy leather gloves and use CAUTION when handling them.
13. DO NOT test for spark by grounding spark plug next to
spark plug hole; spark plug could ignite gas exiting engine.
14. Have machine serviced by an authorized SNAPPER
dealer at least once a year and have the dealer install any
new safety devices.
15. Maintain or replace safety and instruction labels as necessary.
16. Use only genuine SNAPPER replacement parts to
assure that original standards are maintained.
Important Operator Safety Instructions (Continued)
5
Features and Controls
IMPORTANT
The figures and illustrations in this manual are provided
for reference only and may differ from your specific
model. Contact your Snapper dealer if you have questions.
Features and Controls
A. Steering Wheel
B. Engine Speed Control (hidden from view)
C. Ignition Switch
D. Clutch/Brake Pedal
E. Park Brake Latch
F. Blade Pedal
G. Blade Lever
H. Discharge Deflector
I. Override Control
J. Transmission Shift Lever
K. Fuel Tank
F
B
H
I
K
D
G
E
J
A
C
Features and Controls
www.snapper.com6
Operation
Pre-Start Check List
Make the following checks and perform the service required
before each start-up:
1. Check the tire pressure; add or release air as needed to
bring pressure to 12 PSI in front and 12 PSI in rear.
2. Check guards, deflectors and covers to make sure all are
in place and securely tightened.
3. Check engine oil and add oil as needed to bring level up
to the FULL mark (A, Figure 1). Refer to the engine
manual for oil specifications.
4. Adjust the seat (A, Figure 3) as needed to the most
comfortable position. Refer to the Section entitled
“OPERATOR’S SEAT ADJUSTMENT”.
5. Check the blade control to insure it works freely. If the
blade pedals are depressed, the blade lever can be
moved manually from “ON” to “OFF” to stop the blade.
6. Check the Reverse Lockout Mechanism. With the blade
pedals depressed, the shift lever must not go into
reverse.
7. Clean the exterior surfaces of the cutting deck and
engine of any accumulation of dirt, grass, oil, etc. Keep
the engine air intake screen and cooling fins clear at all
times.
8. Add fuel to the fuel tank after pushing the Rear Engine
Rider outside where fumes can dissipate. Make sure the
fuel filler cap (A, Figure 2) is tight, and the vent (B) is
open after refueling. Refer to the engine manual for fuel
specifications.
Operator Seat Adjustment
1. With the engine stopped, loosen the two adjusting
knobs (B, Figure 3) and move the seat to the desired
position. After adjustment, tighten the knobs securely.
NOTE: If the seat does not move after loosening the knobs, it
may be necessary to loosen the 5/16” patch lock screws or
hex nuts
(C)
located at the rear of the seat.
Figure 3: Operator seat adjustment
A
Figure 1: Engine oil ‘Full’ mark
A
Figure 2: Fuel filler cap
B
B
Operation
A
B
A
7
Operation
Starting and Operation
Engine (Electric Start)
IMPORTANT: When the ignition key is turned to “START”, the
engine will turn over, but will not start unless the
Clutch/Brake pedal is pressed all the way down, and the
Blade Lever is in the “OFF” position. The operator should be
in the seat.
Start the engine as follows:
1. Open the vent (B, Figure 2) on the fuel filler cap (A) by
turning counterclockwise.
IMPORTANT: Failure to open the vent on the fuel filler cap
can cause the engine to stall.
2. Move the transmission shift lever to the (N) Neutral
position. Refer to the section entitled “Wheel Drive”.
IMPORTANT: DO NOT start the engine with the transmission
shift lever in a drive position.
2. Make certain the Blade Lever (A, Figure 4) is in the
“OFF” position.
3. Press the Clutch/Brake Pedal (A, Figure 5) all the way
down and hold while starting the engine.
5. Move the engine speed control (A, Figure 6) to the
choke position (B) to start a cold engine.
6. Turn the ignition key (A, Figure 7) to the “START”
position until the engine starts.
NOTE: If after 5 seconds of cranking the engine does not
start, release the key, make sure the Clutch/Brake Pedal is
fully depressed, and attempt starting again after waiting for
approximately 20 seconds.
7. After the engine starts, move the engine speed control
to the “FAST” position and allow a brief warm-up until
engine runs smooth.
(Continued on Next Page)
Figure 4: Blade lever (in ‘Off’ position)
A
Operation (Continued)
WARNING
It is possible to start the engine with the transmission
shift lever in a drive position. Follow starting instructions
carefully.
!
!
Figure 5: Engaging the clutch/brake pedal
A
Figure 6: Engine speed control
A
B
Figure 7: Ignition key
A
www.snapper.com8
Operation
Starting and Operation (Continued)
Engine (Electric Start) (Continued)
8. Should the battery be too weak to start the engine, refer
to the Section entitled “Engine (Manual Start)” to
manually start the electric start engines.
9. On Model 3317523BVE and C3317523BVE, the engine is
equipped with a fuel shut-off solenoid. If the battery is
dead, the engine can be started with the recoil back-up
starter if the engine speed control is in the choke
position (HOT engine or COLD engine).
Engine (Manual Start)
IMPORTANT: When the key is turned to “ON”, and the recoil
handle is pulled, the engine will turn over, but will not start
unless the Clutch/Brake Pedal is pressed all the way down
with the Park Brake engaged, and the Blade Lever is in the
“Off” position.
Start the engine as follows:
1. Open the vent (B, Figure 2) on the fuel filler cap (A) by
turning counterclockwise.
IMPORTANT: Failure to open the vent on the fuel filler cap
can cause the engine to stall.
2. Move the transmission shift lever to the (N) Neutral
position. Refer to the section entitled “Wheel Drive”.
IMPORTANT: DO NOT start the engine with the transmission
shift lever in a drive position.
3. Make certain the Blade Lever (A, Figure 4) is in the
“OFF” position.
4. Press the Clutch/Brake Pedal (A, Figure 8) all the way
down, move the park brake latch (B) over, and release
the clutch/brake pedal to set the park brake.
5. Move the engine speed control (A, Figure 6) to the
choke position (B) to start a cold engine.
6. Turn the key (A, Figure 9) to the “ON” position.
7. Pull the starter rope, located on the engine recoil, with a
smooth, even motion until the engine starts.
NOTE: Always guide the starter rope back into the recoil
housing. Never allow rope to snap back.
After the engine starts, move the engine speed control
to the “FAST” position.
8. Allow a brief warm-up until the engine runs smooth.
Operation (Continued)
WARNING
It is possible to start the engine with the transmission
shift lever in a drive position. Follow starting instructions
carefully.
!
!
Figure 8: Setting the park brake
A
B
Figure 9: Key
A
9
Operation
Starting and Operation (Continued)
Mower Blade
1. With the engine running, move the engine speed control
to the “FAST” position.
2. Move the blade lever (A, Figure 10) forward to the “ON”
position, then depress the blade pedals (B) to hold the
blade lever in the “ON” position.
Wheel Drive
1. With the engine running, adjust the engine speed control
to the “FAST” position.
2. Depress the clutch/brake pedal (A, Figure 11).
3. Place the transmission shift lever (A, Figure 12) into
the first forward speed notch (B).
4. Release the clutch/brake pedal to begin forward motion.
5. During forward motion, the transmission shift lever
may be placed in any desired forward speed without
depressing the clutch/brake pedal.
NOTE: For best cutting results, move the transmission shift
lever into a slow forward speed and the engine speed control
to a fast position. This combination will allow the mower
blades to lift the grass while cutting smoothly and evenly.
Figure 10: Engaging the mower blade
A
Operation (Continued)
Figure 11: Engaging the clutch/brake pedal
A
Figure 12: Transmission shift lever
A
WARNING
Once blade is disengaged, it should come to a complete
stop in 3 seconds or less. If the blade continues to rotate
after 3 seconds, the blade brake must be adjusted. Refer to
Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning properly.
!
!
WARNING
DO NOT operate blades in reverse. STOP BLADES. LOOK
and SEE behind and down for children, pets and hazards
before and while backing.
!
!
B
B
www.snapper.com10
Operation
Stopping - Engine,
Wheel Drive, Blade
Engine
1. Stop the engine by turning the key (A, Figure 13) to the
“OFF” position.
Wheel Drive
1. Stop motion of the Rear Engine Rider by pushing the
clutch/brake pedal (A, Figure 14) all the way down to
apply the brake.
Mower Blade
1. Stop the mower blade by releasing the blade pedals (A,
Figure 15) or moving the blade lever (B) rearward to the
“OFF” position.
Operation (Continued)
WARNING
DO NOT leave the machine with the engine running. STOP
Blade. STOP engine. Shift to neutral and engage park brake.
Remove key.
!
!
WARNING
Once blade is disengaged, it should come to a complete
stop in 3 seconds or less. If the blade continues to rotate
after 3 seconds, the blade brake must be adjusted. Refer to
Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning properly.
!
!
Figure 13: Turning key to ‘Off’
A
Figure 15: Stopping the mower blade
B
A
Figure 14: Engaging the clutch/brake pedal
A
Loading...