Parts Manual fo
r
R
REAR ENGINE RIDE
SERIES 23
MODEL
281023BVE (84871)
281123BV (7800102)
281123BV (84872)
281123BV (84940)
281123BVE (84874)
281123HVE (84883)
2811523BV (7084940)
281223BVE (85622)
2812523BVE (7085622)
2812523BVE (7800104)
281323BVE (84876)
2813523BVE (7085624)
2813523BVE (85624)
301123BV (84873)
301123BV (84941)
3011523BV (7800103)
301223BVE (85623)
3012523BVE (7085623)
3012523BVE (7800105)
301323BVE (84877)
3013523BVE (7085625)
3013523BVE (85625)
331323HVE (84885)
331523BVE (84878)
331523KVE (7084879)
331523KVE (7800106)
331523KVE (84879)
331623BVE (84954)
331723BVE (7084954)
331723BVE (7800107)
W280923BV (84881)
W281023BVE (84884)
W301023BVE (84882)
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
McDonough, GA, 30253 U.S.A.
Revision 5,
8/24/2007
Manual No. 7006152
TP 400-5003-5-RE-N
s
PAGE GROUP
4
6
10
14
16
20
22
24
26
28
30
34
36
40
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
78
WHEELS- FRONT & REAR
FRONT END, STEERING
MAIN CASE & L.H. FENDER
LEFT HAND FENDER & BEARING
DIFFERENTIAL, R. H. FENDER
YOKE LIFT COMPONENTS
PRIMARY CHAIN CASE & SMOOTH CLUTCH
GEAR SHIFTER ASSEMBLY
FUEL TANK & SEAT
ENGINE, MUFFLER, DRIVE DISC
CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
30" CUTTING DECK, DEFLECTOR
BELTS, BRAKES, INTERLOCK
RAILS, LIFT ARMS, CAM LIFT
BLADE STOP PEDALS
SPINDLE
DECALS
ELECTRICAL SYSTEMS (For 9, 11 & 11.5HP Briggs Recoil)
ELECTRICAL SYSTEMS (For 10, 11, 12, 12.5 & 13HP Briggs)
ELECTRICAL SYSTEMS (For 13.5, 15, 16 & 17HP Briggs)
ELECTRICAL SYSTEMS (For 11 & 13HP Honda)
ELECTRICAL SYSTEMS (For 15HP Kohler)
ELECTRICAL SYSTEMS (Briggs Magneto Ground)
ELECTRICAL SYSTEMS (Kohler Magneto Ground)
WIRING SCHEMATIC (9, 11 & 11.5HP Recoil Start Briggs)
WIRING SCHEMATIC (10, 11, 12, 12.5 & 13 HP Briggs)
WIRING SCHEMATIC (13.5, 15, 16 & 17 HP Briggs Engines)
WIRING SCHEMATIC (11 & 13 HP Honda Engines)
WIRING SCHEMATIC (14 & 15 HP Kohler Engines)
HARDWARE BAGS
ACCESSORIES & ATTACHMENTS
Table Of Content
SERIES 23
Manual No. 7006152REAR ENGINE RIDER
3
TP 400-5003-5-RE-N
WHEELS- FRONT & REAR
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
4
SERIES 23
WHEELS- FRONT & REAR
p
y
Part No Descri
1 7058943 2 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 2, 3, 4, 5 & 6)
2 7073563 1 TIRE, 11 x 4.00-4 (Kenda)
3 7017146 1 RIM (For 4.10/3.50 x 4 Tire)
4 7011807 2 BALL BEARING, Flange (3/4” I.D.)
5 7012234 1 VALVE STEM, Snap In
6 7014669 1 LUBE Fitting
7 7031038 1 CAP, Dust
8 7011032 1 FELT SEAL
9 7010935 3 WASHER, .77 x 1.13 x .06 Flat
10 7011022 1 HUB CAP
11 7091516 1 COTTER PIN, 5/32 x 1”
12 7010821 1 TUBE, Inner (For 4.10/3.50 x 4 Tire)
13 7058951 2 ASSEMBLY, Rear Tire & Rim (28”, 30”, 33” Models) (Includes Items 5, 14 & 15)
14 7073584 1 TIRE, 16-6.50 x 8
15 7017147 1 RIM, Extra Wide (For 16/7.50 x 8 Tire) (33” Models)
16 7040434 1 HUB, Rear Wheel L. H. (Weldment)
17 7040433 1 HUB, Rear Wheel R. H. (Weldment)
18 7011035 1 AXLE BOLT, Left Hand (5/16-24 x 1-5/8” Tapered)
19 7011201 1 NUT, Wheel Bolt, 5/16-24 Hex Center Lock
20 7023522 1 CAP, Hub, L. H. (Long Axle)
21 7011013 1 WHEEL BOLT, Right Hand (5/16-24 x 2” Tapered)
22 7023895 1 CAP, Hub
23 7011817 1 SEAL, 1.22" ID x 1.875" OD
24 7031732 1 CAP, Seal 1.0" ID x 1.67" OD, Right Hand (Shown) (8 & 10 HP)
25 7012332 1 CLAMP, Right Hand 2” (used on 8, 10, 11.5, 12.5, 13 &
25 7014542 1 CLAMP, Right Hand 2.69" (used on 12, 14 & 15 HP)
26 7091502 3 BOLT, 1/2-20 x 3/4” Lug, GR 5
tionItem Qt
Note
17 HP)
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
5
TP 400-5003-5-RE-N
FRONT END, STEERING
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
6
SERIES 23
FRONT END, STEERING
p
y
Part No Descri
1 7058030 1 ASSEMBLY, Steering Wheel (for 5/8” shaft) Includes item 2
2 7023781 1 LOGO, Steering Wheel
3 7013862 1 ROLL PIN, 1/4 x 1-1/2”
4 7023667 1 FOAM COVER, Steering Shaft
5 7023671 1 COVER, Steering Shaft
6 7090296 1 PIN, 3/16 x 1” Cotter
7 7090183 2 WASHER, .66 x 1.31 x .09 Flat
8 7046158 1 BUSHING, Nylon
9 7101192 1 CABLE, Brake, Snap-In replaces 7072648 (voided)
10 7022449 1 CABLE, Clutch/Brake (54.32” long) used on 25”, 28” & 30” Decks
10 7074131 1 CABLE, Clutch/Brake (55” long) used on 33” & 42” Decks
11 7090372 1 NUT, 1/4-20 Hex Center Lock, GR 5 or B
12 7034174 2 CONNECTOR, Cable
13 7091495 1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
14 7054378 1 WELDMENT, Front Axle, Narrow used on 25”, 28” & 30” Decks
14 7053266 1 WELDMENT, Front Axle, Wide used on 33” Decks
15 7074561 1 BOTTLE, Water
16 7074560 1 HOLDER, Bottle (Wire)
17 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
18 7011714 1 HAIR PIN 2-1/4”
19 7038243 1 LATCH, Parking Brake
20 7015444 1 SPRING, Parking Brake Latch
21 7014049 2 FOOT PAD, Short (5.5” x 4.7”)
21 7014048 2 FOOT PAD, Long (5.5” x 9.5”)
22 7010776 1 RING, 1/2” External Retaining (Heavy Duty)
23 7047888 1 WELDMENT, Clutch Pedal
24 7011815 1 PAD, Pedal
25 7010694 1 BUSHING, Nylon
26 7046232 1 WELDMENT, Steering Shaft
27 7090753 1 PIN, 3/16 x 1-1/2” Cotter
28 7010746 2 RING, 5/8” External Retaining
29 7010935 6 WASHER, .77 x 1.13 x .06 Flat
30 7010986 4 BEARING, Nylon
31 7090364 2 PIN, 5/32 x 1” Cotter
32 7090122 4 WASHER, 3/8” Flat SAE or 7091514
33 7013321 4 BUSHING, Tie Rod
34 7041687 1 WELDMENT, King Pin, Left Hand
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
7
TP 400-5003-5-RE-N
FRONT END, STEERING
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
8
SERIES 23
FRONT END, STEERING
p
y
Part No Descri
35 7041688 1 WELDMENT, King Pin, Right Hand
36 7090365 2 PIN, 1/8 x 3/4” Cotter
37 7013023 1 TIE ROD, Left Hand (7.41” long)
37 7012541 1 TIE ROD, Left Hand (9.91” long)
38 7012933 1 TIE ROD, Right Hand (7.41” long)
38 7012540 1 TIE ROD, Right Hand (9.91” long)
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
9
TP 400-5003-5-RE-N
MAIN CASE & L.H. FENDER
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
10
SERIES 23
MAIN CASE & L.H. FENDER
p
y
Part No Descri
1 7028990 1 COVER, Battery
2 7028989 1 COVER, Switch
3 7073268 1 COVER, Solenoid
4 7074210 1 BRACKET, Belt Adjuster
5 7091198 2 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
6 7090358 1 SCREW, 5/16-24 x 2-1/2” Hex Head Cap, GR 5
7 7031100 1 TUBE CLAMP
8 7010969 2 NUT, 5/16-24 Flange Lock (Large)
9 7074650 1 BUSHING, Pivot replaces 7022509 (voided)
10 7053697 1 WELDMENT, Main Case (Standard) (shown)
10 7053698 1 WELDMENT, Main Case (Commercial) (not shown) used on E331523KVE Model
11 7034299 2 WING, Rear
12 7028200 2 SWIVEL, Adjustable
13 7091503 2 HAIR PIN, 3/32 x 1-1/2”
14 7090793 4 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
15 7011791 4 RETAINER, 5/16” Bolt
16 7091296 4 WASHER, 5/16” Flat
17 7091315 7 WASHER, .32 x .58 x .08 Split Lock
18 7091297 7 NUT, 5/16-24 Hex, GR 5
19 7090595 2 BOLT, 5/16-18 x 3/4” Hex Flange Lock, GR 5
20 7024998 3 PLUG, 1” Hole Used on Euro models only
21 7090238 4 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
22 7077692 4 BOLT, M8-1.25 x 25mm, Self-Tap (Kohler)
23 7074946 1 PLATE, Engine (Kohler Engine) used on E331523KVE Model
24 7030798 2 BUMPER, Rear
25 7036367 1 BUMPER (1-Piece) (33” Deck)
26 7090484 4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap or 7091506
27 7010153 2 CAP, Bumper
28 7090188 2 WASHER, 11/32” Flat
29 7090361 14 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap or 7091867
30 7090391 1 WASHER, 5/16” Internal Tooth Lock
31 7012652 1 CLIP, Wire
32 7090206 1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
33 7091513 4 SCREW, 5/16-24 x 1-3/4” Hex Head Cap, GR 5
34 7091272 7 FASTENER, 1/4” Ratchet
35 7047189 1 BRACKET, Drive Support
36 7090585 6 NUT, 5/16-18 Hex Flange Lock, GR 5
tionItem Qt
Note
only
only
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
11
TP 400-5003-5-RE-N
MAIN CASE & L.H. FENDER
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
12
SERIES 23
MAIN CASE & L.H. FENDER
p
y
Part No Descri
37 7036419 1 BELT GUIDE, K 30/33 (9.48" Bolt Pattern Bent Top) used on E331523KVE Model
38A 7017653 1 BELT GUIDE, 25, 26, 28, 41" (5.74" Bolt Pattern, 4.74" Belt Gap)
38B 7036418 1 BELT GUIDE, 30/33 (5.74" Bolt Pattern, 5.0" Belt Gap) used on 331723BVE Model only
39 7023676 1 SHIFT LINK, Long (5/16-24 both ends)
40 7041384 1 WELDMENT, Shift Arm
41 7033799 1 CROSS BRACE
42 7011018 1 SHIFT LINK, Short (5/16-24 thread)
43 7073735 1 BRACKET, Switch
44 7090981 2 SCREW, #10-32 x 1/4” Hex Washer Self-Tap
45 7037285 1 FENDER, Left Hand (1.628" I. D. Hole)
tionItem Qt
Note
only
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
13
TP 400-5003-5-RE-N
LEFT HAND FENDER & BEARING
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
14
SERIES 23
LEFT HAND FENDER & BEARING
p
y
Part No Descri
1 7012332 2 BOOT CLAMP, 2”
2 7075115 1 BOOT, Rear Axle, Thick Flange
3 7011072 1 WASHER, Thrust
4 7011071 1 THRUST WASHER
5 7052827 1 ASSEMBLY, DX Bearing
6 7074182 2 BEARING, DX
7 7074500 1 SEAL, Axle (Dust/Grease)
8 7075848 1 FITTING, Lube, 45 Degree, 3/16” w/Hex (long shank) or 7013324
9 7011070 1 TIE ROD (5/16-24 thread- both ends)
10 7037285 1 FENDER, Left Hand (1.628” I. D. Hole)
11 7010969 1 NUT, 5/16-24 Flange Lock (Large)
12 7012271 1 WASHER, Shim or quantity as required
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
15
TP 400-5003-5-RE-N
DIFFERENTIAL, R. H. FENDER
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
16
SERIES 23
DIFFERENTIAL, R. H. FENDER
p
y
Part No Descri
1 7090362 13 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap
2 7012296 1 BEARING, Axle (R. H. Fender)
2 7054372 1 BEARING-DX, Axle (R. H. Fender) includes 1-1/8" I.D. (DX) bearing
3 7010969 1 NUT, 5/16-24 Flange Lock (Large)
4 7031079 1 WASHER, Thrust
5 7038067 1 PLATE, Differential Note: 4 holes offset - align
6 7022115 4, 8 SPACER, Pinion
7 7021127 4, 8 GEAR, Differential Pinion (12T 12P)
8 7011072 1 WASHER, Thrust
9 7051584 1 * ASSEMBLY, Drive Hex Tube
10 7010988 1 WASHER, Nylon
11 7010964 1 GEAR, 11 Tooth, 10 Pitch
12 7010941 1 CHAIN, 46 Pitch (#35 Endless)
13 7021129 1 SPROCKET, 34T, 3/8P
14 7010965 1 RING, 1-3/16” External Retaining
15 7021128 1 SPACER, Differential Case
16 7012332 2 BOOT CLAMP, 2”
17 7075115 1 BOOT, Oil Seal (Short Axle)
18 7011024 1 PLUG, 1/2” Cup Insert
19 7037279 1 CASE, Transmission
20 7028762 1 GASKET, Transmission Case
21 7037280 1 FENDER, Right Hand (1.62” Dia. Hole)
22A 7021158 1 GEAR, 63 Tooth 10 Pitch (4 Hole)
22B 7027644 1 GEAR, 63 Tooth 10 Pitch (8 Hole)
23 7047763 1 ASSEMBLY, Long Axle (Includes Gear)
24 7074431 1 SPACER, Differential Case
25 7057398 1 ASSEMBLY, Short Axle, 23T (Includes Gear)
26 7012333 4, 8 BOLT, 5/16-24 x 1-5/8” Hex Special Lock (Vibresist)
27 7011156 2 5/16” O-RING
28 7011782 2 WASHER, 5/16” Belleville
29 7090395 1 WASHER, 5/16” External Tooth Lock
30 7090188 1 WASHER, .34 x .69 x .08 Flat
31 7011042 1 SCREW, 5/16-24 x 2-5/8” Hex Head Cap
32 7090361 11 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
35 7061017 1 GREASE, Transmission (24 oz. Required)
-- 7060411 1 KIT, Differential (4 Pinion)
-- 7060662 1 KIT, Differential (8 Pinion w/DX Bearing)
tionItem Qt
Note
properly to prevent binding.
Footnotes:
Note: * Assembly includes two bearings inside hex tube (p/n 7015140, not shown) & one nylon washer (p/n 7010988, item
10).
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
17
TP 400-5003-5-RE-N
DIFFERENTIAL, R. H. FENDER
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
18
SERIES 23
DIFFERENTIAL, R. H. FENDER
p
y
Part No Descri
-- 7075479 1 KIT, Long & Short Axle (Includes items 23, 24, & 25)
tionItem Qt
Note
Footnotes:
Note: * Assembly includes two bearings inside hex tube (p/n 7015140, not shown) & one nylon washer (p/n 7010988, item
10).
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
19
TP 400-5003-5-RE-N
YOKE LIFT COMPONENTS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
20
SERIES 23
YOKE LIFT COMPONENTS
p
y
Part No Descri
1 7013885 1 SPRING, Clutch & Brake
2 7014664 1 BOLT, 5/16-18 Shoulder
3 7091198 2 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
4 7090187 1 WASHER, 5/16” Split Lock
5 7090196 1 NUT, 5/16-18 Hex, GR 5 or B
6 7014663 2 SLIDE HALF
7 7047190 1 BRACKET, Slide
8 7090122 2 WASHER, 3/8” Flat SAE
9 7015464 1 STUD, Clutch Link (3/8-24 thread)
10 7090037 1 PIN, 3/32 x 3/4” Cotter or 7091597
11 7090390 1 WASHER, 3/8” Internal Tooth Lock
12 7091630 1 NUT, 3/8-24 Hex, GR 5 or B or 7090155
13 7090539 2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
14 7059068 1 ASSEMBLY, Leaf Spring
15 7073733 1 ARM, Yoke
16 7046162 1 LIFT, Yoke
17 7011201 2 NUT, 5/16-24 Hex Center Lock
18 7011048 2 BEARING, Yoke
19 7011763 2 FENDER WASHER, 5/16”
20 7090238 2 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
21 7033291 1 COLLAR, Yoke
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
21
TP 400-5003-5-RE-N
PRIMARY CHAIN CASE & SMOOTH CLUTCH
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
22
SERIES 23
PRIMARY CHAIN CASE & SMOOTH CLUTCH
p
y
Part No Descri
1 7052683 1 ASSEMBLY, Primary Chain Case (Includes the following 16 items)
2 7041136 1 WELDMENT, Primary Chain Case Half, Right Hand
3 7028761 1 GASKET, Primary Chain Case
4 7011121 2 WASHER, 5/8” Belleville
5 7010756 2 BEARING, .625 x 1.37 x .435
6 7018963 1 WELDMENT, Sprocket & Shaft
7 7010614 1 KEY,#5 Woodruff
8 7039778 1 PRIMARY CHAIN CASE HALF, Left Hand
9 7010942 2 BEARING, Needle 1.355” ID x 1.6245” OD x .5” Wide
10 7011086 2 THRUST WASHER, Nylon
11 7040355 1 WELDMENT, Hub & Sprocket
12 7010941 1 CHAIN, 46 Pitch (#35 Endless)
13 7090307 10 SCREW, 10-24 x 1/2” Hex Washer Self-Tap
14 7022785 1 ROLLER, 1-3/8 Long
15 7010776 1 RING, 1/2” External Retaining (Heavy Duty)
16 7011024 1 PLUG, 3/4” Cup Insert
17 7091505 1 NUT, 5/8-18 Hex Nyloc
18 7019260 2 O-RING, 1/2 x 5/8”
19 7027981 1 WASHER, Shim .625 x .875
20 7053114 1 ASSEMBLY, Smooth Clutch (non-asbestos) (Includes the following 5 items)
21 7059443 1 HUB, Driven Disc (assembly) replaces 7054243 (voided)
22 7053103 1 DISC, Driven (rubber tire bonded to rim)
23 7014523 1 THRUST WASHER
24 7032331 1 PLATE, Drive Disc
25 7092081 4 NUT, 5/16-24 Hex Flange Lock or 7090480, center lock flange
26 7052497 1 ASSEMBLY, Brake Lever (Includes brake pad & rivet)
27 7012313 1 RING, 3/8” External Retaining
28 7090303 1 NUT, 1/4-28 Hex Top Lock
29 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
30 7072593 1 * SPACER, Brake Arm Pivot (.418/.403 long) replaces 7010916 (.300/.285
31 7091504 1 SCREW, 1/4-28 x 1” Hex Head Cap, (Washer Face) GR 5
32 7072406 1 * SPRING, Torsional Brake Return
33 7061017 GREASE, Transmission (Use 2 oz. Maximum)
tionItem Qt
Note
nut
long)
Footnotes:
Note: * Brake return replacement kit (7061197) is made of items 30 & 32.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
23
TP 400-5003-5-RE-N
GEAR SHIFTER ASSEMBLY
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
24
SERIES 23
GEAR SHIFTER ASSEMBLY
p
y
Part No Descri
1 7023656 1 GRIP, Shift Handle
2 7059212 1 WELDMENT, Shift Handle
3 7023914 1 PIN, 1/4 x 1-3/4” Tapered Clevis
4 7090037 1 PIN, 3/32 x 3/4” Cotter
5 7031036 2 WASHER, Thrust
6 7019245 1 BUSHING, 3/4 x 1.62 Flange (Nylon)
7 7091298 1 NUT, 5/16-18 Hex Nyloc
8 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
9 7058763 1 * ASSEMBLY, Speed Adjustment Latch
10 7026292 1 SPRING part of Speed Adjustment Latch
11 7090196 1 NUT, 5/16-18 Hex, GR 5 or B
12 7010754 1 SPRING, Shift Detent
13 7073289 1 LEVER, Over-Ride
14 7091595 1 WASHER, .47 x .92 x .065 Flat
15 7015761 1 SHOULDER BOLT, 5/16-18
16 7019246 1 BUSHING, 3/4 x I.O. Flange (Nylon)
17A 7040598 1 WELDMENT, Arm, Shift Handle
17B 7043201 1 WELDMENT, Arm, Shift Handle (w/grease ftg. Hole)
18 7010817 1 LUBE FITTING, 3/16” Press-In used with 7043201
19 7091315 1 WASHER, .32 x .58 x .08 Split Lock
20 7091297 1 NUT, 5/16-24 Hex, GR 5
tionItem Qt
Note
Ass'y
Footnotes:
Note: * Assembly is comprised of: Shift Detent Weldment (7041232), Shoulder Rivet (7029022), Reverse Stop (7073218) &
item 10.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
25
TP 400-5003-5-RE-N
FUEL TANK & SEAT
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
26
SERIES 23
FUEL TANK & SEAT
p
y
Part No Descri
1 7075071 1 SEAT, Operator (11.58” tall) (shown) (Michigan V-2400 Series) used on 12HP & Higher Models
1 7075376 1 SEAT, Operator (9.30” tall) (Michigan V-2300 Series) used on 2811523BV,
2 7051905 1 ASSEMBLY, Fuel Tank (Includes item 3) used on 9, 10 & 11.5HP Models
2 7052435 1 ASSEMBLY, Fuel Tank with Gauge (Includes item 3A) used on 12, 12.5, 14.5, 15 &
3 7012515 1 CAP, Fuel Tank
3A 7019377 1 CAP, Fuel Tank w/Gauge
4 7029900 4 CLAMP, Fuel Line replaces 7012222 clamp
5 7076272 1 HOSE, Fuel (1/4” I.D. x 8-1/2” long) used on Briggs 8-17HP
5 7012912 1 HOSE, Fuel (1/4” I.D. x 12-1/2” long) used on Kohler Models only
5 7041996 1 HOSE, Fuel (1/4” I.D. x 6-1/2” long) used on Kohler Models only
6 7077351 1 HOSE, Fuel (1/4” I.D. x 3-1/2” long)
7 7014359 1 FILTER, Fuel (In-Line)
8 7024507 1 VALVE, Fuel Shut-Off (Accessory)
9 7033377 1 BRACKET, Fuel Tank (Rear)
10 7091542 2 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx #T-40)
11 7029211 1 SWITCH, Seat, Quick Mount (NC) used on seat, p/n 7028650
11A 7023354 1 SWITCH, Seat (NC)
12 7091714 4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5
13 7075018 2 BRACKET, Seat
14 7011791 4 RETAINER, 5/16” Bolt
15 7091038 2 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
16 7090539 2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
17 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
18 7033470 1 PLATE, Throttle Control
19 7022751 1 CONTROL, Throttle (23.6” long) (Briggs Engines)
19 7074320 1 CONTROL, Throttle (34.6” long) (Kohler Engines)
19 7075089 1 CONTROL, Throttle (34.6” long) (Honda Engines)
20 7090672 2 NUT, 5/16-18 Hex Flange Top Lock or 7090951
21 7013849 2 SPACER, .33 x .63 x .156
22A 7023735 2 KNOB, Fluted, 5/16-18 internal thread (2.15 O.D.)
22B 7023191 2 KNOB, 3-Prong, 5/16-18 x 3/4” external thread used on seat, p/n 7028650
tionItem Qt
Note
3011523BV
17HP Models
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
27
TP 400-5003-5-RE-N
ENGINE, MUFFLER, DRIVE DISC
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
28
SERIES 23
ENGINE, MUFFLER, DRIVE DISC
p
y
Part No Descri
1 -- 1 * ENGINE, 9HP Briggs (Mod 28B702-1154-E1) recoil start
1 -- 1 * ENGINE, 10HP Briggs (Mod 214707-0113-E1) electric start
1 -- 1 * ENGINE, 11HP Briggs (Mod 21A907-0124-E1) electric start
1 -- 1 * ENGINE, 11HP Briggs (Mod 21A902-0127-E1) recoil start
1 -- 1 * ENGINE, 11HP Honda (Mod GXV340, Type K2DET3) electric start
1 -- 1 * ENGINE, 11.5HP Briggs (Mod 217802-0113-E1) recoil start
1 -- 1 * ENGINE, 12.5HP Briggs (Mod 219907-0131-E1) electric start
1 -- 1 * ENGINE, 13HP Briggs (Mod 21A907-0128-E1) electric start
1 -- 1 * ENGINE, 13HP Honda (Mod GXV39K, Type 1DET3) electric start
1 -- 1 * ENGINE, 13.5HP Briggs (Mod 21B907-0137-E1) electric start
1 -- 1 * ENGINE, 15HP Briggs (Mod 284H07-0115-E1) electric start
1 -- 1 * ENGINE, 15HP Kohler (Mod CV15ST, Type PS-41584) electric start
1 -- 1 * ENGINE, 16 or 17HP Briggs (Mod 31F777-0115-E1) electric start
2 7027972 1 ASSEMBLY, Oil Valve
3 7015352 1 GASKET, Exhaust
4 7090362 2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap
5A 7074453 1 MUFFLER w/Heat Shield (Briggs 11 thru 17HP)
5B 7019358 1 MUFFLER (Kohler 14 & 15HP)
6 7091738 2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR8
7 7010210 1 KEY,1/4” Square x 2” Long
8 7090132 2 SET SCREW, HRSS, 3/8-16 x 3/8”
9A 7072658 1 WELDMENT, 5.75” O.D. Drive Disc used on 28” & 30” Decks
9B 7074187 1 WELDMENT, 5.25” O.D. Drive Disc used on 33” Deck Models
10 7090585 2 NUT, 5/16-18 Hex Flange Lock, GR 5
11 7091495 1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
12 7013849 1 SPACER, .33 x .63 x .156
13 7091065 1 NUT, 1/4-20 Hex Flange Lock
14 7091576 1 NUT, 1/4-20 Hex, GR 5 or B not shown (attaches to starter
tionItem Qt
Note
terminal on Briggs 12.5 or 17HP)
Footnotes:
Note: * Purchase engine parts from engine manufacture dealer.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
29
TP 400-5003-5-RE-N
CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
30
SERIES 23
CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
p
y
Part No Descri
1 7073434 1 COVER, Spindle
2 7091015 2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
3 7091016 4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
4A 7061970 1 DECK, 28” Replacement (Painted deck w/decals & wheel
4B 7061972 1 DECK, 33” Replacement (Painted deck with decals)
5 7090731 6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR 5
6 7091070 8 NUT, 5/16-18 Hex Flange Lock, GR 5
7 7033570 1 BRACKET, Gage Wheel (Front)
8 7091532 3 SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR 5
9 7091518 3 NUT, 3/8-24 Hex Nyloc
10 7019190 3 WHEEL, Gage
11 7015272 3 SPACER
12 7033571 2 BRACKET, Gage Wheel (Rear)
13 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 or 7090001
14 7016983 1 COVER, 28” Mulcher
14 7016984 1 COVER, 33” Mulcher
15 7026233 1 DEFLECTOR, Discharge, 28” & 33”
15A 7500484 1 ASSEMBLY, Discharge Deflector, 28” & 33” (without decal) Incl. items 15, 16, 18, 19, & 20
16 7026483 2 PUSH NUT, 1/4”
17 7091811 3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 or 7091811
18 7026234 1 PIN, Hinge
19 7016341 1 SPRING, Hinge
20 7033780 1 HINGE, Deflector (Deck side)
21 7091296 2 WASHER, 5/16” Flat
22 7013010 1 DECAL, Danger, (Cut Finger) or 7026831
23 7035635 1 BLADE, 28” Hat Shaped Hi-Lift standard equipment
23 7034168 1 BLADE, 33” Hat Shaped Hi-Lift standard equipment
24 7026453 1 BLADE, Ninja, 28”
24 7024741 1 BLADE, Ninja, 33”
25 7019515 1 BLADE, 28”
25 7019523 1 BLADE, 33”
26 7090492 2 NUT, 5/16-18 Wing
27 7091939 2 NUT, 1/2-20 Hex, GR 5 or B was 7090559, Hex Jam Nut
28 7090509 2 WASHER, 1/2” Internal Tooth Lock
29 7090613 9 NUT, 3/8-16 Hex Flange Lock
30 7090612 3 BOLT, 3/8-16 x 3/4” Hex Flange Lock
31 7090491 2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR 5 was 7090392
tionItem Qt
Note
bracket fasteners)
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
31
TP 400-5003-5-RE-N
CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
32
SERIES 23
CUTTING DECKS, DEFLECTOR (28" & 33" Hi-Vac)
p
y
Part No Descri
32 7060480 1 KIT, Air Lift, Hi-Vac (Includes items 33, 34, 35 & 36) used on 28” & 33” Decks
33 7037723 2 AIR LIFT, Hi-Vac (3 hole)
34 7090228 6 SCREW, 5/16-24 x 11/16” Oval Head Machine
35 7090391 6 WASHER, 5/16” Internal Tooth Lock
36 7090223 6 NUT, 5/16-24 Hex
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
33
TP 400-5003-5-RE-N
30" CUTTING DECK, DEFLECTOR
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
34
SERIES 23
30" CUTTING DECK, DEFLECTOR
p
y
Part No Descri
1 7073434 1 COVER, Spindle
2 7091015 2 SCREW, 1/4-20 x 3-1/2” Hex Head w/Free Spinning Washer
3 7091016 4 SCREW, 1/4-20 x 5/8” Hex Head w/Free Spinning Washer
4 7061971 1 DECK, 30” Replacement (Painted deck with decals)
5 7034024 1 * BRACKET, Front Anti-Scalp
6 7034026 1 * BRACKET, Anti-Scalp, 30” L.H. Rear
7 7034025 1 * BRACKET, Anti-Scalp, 30” R.H. Rear
8 7090731 8 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR 5
9 7090585 10 NUT, 5/16-18 Hex Flange Lock, GR 5 or 7091070
10 7090859 3 * SCREW, 3/8-24 x 3-3/4” Hex Head Cap, GR 5 or 7091532
11 7015272 3 * SPACER
12 7019190 3 * WHEEL, Gage
13 7090289 3 * NUT, 3/8-24 Hex Center Lock, GR 5 or B or 7091518 (3/8-24 Hex Nyloc
14 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
15 7091296 2 WASHER, 5/16” Flat
16 7090492 2 NUT, 5/16-18 Wing
17 7052553 1 ASSEMBLY, 30” Deflector (Incl. items 18, 19, 20 & 22)
18 7026846 1 PIN, Hinge (Straight, 8-7/8” long)
19 7024569 1 HINGE, Deflector (8” long)
20 7016428 1 SPRING, Hinge
21 7025047 1 DEFLECTOR, 30” Deck
22 7013010 1 DECAL, Danger, (Cut Finger)
23 7091510 3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 or 7090606
24 7090612 3 BOLT, 3/8-16 x 3/4” Hex Flange Lock
25 7090613 9 NUT, 3/8-16 Hex Flange Lock
26 7090392 2 SCREW, 1/2-20 x 1” Hex Head Cap, GR 5
27 7090509 2 WASHER, 1/2” Internal Tooth Lock
28 7090559 2 NUT, 1/2-20 Hex Jam
29 7018069 1 BLADE, 30”
30 7026565 1 BLADE, Ninja, 30”
31 7060735 1 KIT, Air Lift (Includes items 32 thru 35)
32 7090228 6 SCREW, 5/16-24 x 11/16” Oval Head Machine
33 7031724 2 AIR-LIFT (30” Models)
34 7090391 6 WASHER, 5/16” Internal Tooth Lock
35 7090223 6 NUT, 5/16-24 Hex
tionItem Qt
Note
Nut)
Footnotes:
Note: * These parts comprise # 7061157 (Gage Wheel Kit for 30” Snapper Decks). Bracket mounting fasteners are also
included.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
35
TP 400-5003-5-RE-N
BELTS, BRAKES, INTERLOCK
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
36
SERIES 23
BELTS, BRAKES, INTERLOCK
p
y
Part No Descri
1 7043844 1 * BELT, Drive (73.75” AA Section) used on 33” Deck Models
1 7022252 1 * BELT, Drive (72.75” AA Section) used on 25”, 28” & 30” Decks
2 7074467 1 NUT, 3/4-16 Hex Jam, GR 8
3 7032027 2 WASHER, 49/64” I.D. x 1-1/2” O.D. Flat
4 7018781 1 PULLEY, Deck
5 7015290 1 PULLEY, Hub (Powdered Metal)
6 7091299 2 NUT, 3/8-16 Hex Nyloc
7 7029624 2 IDLER PULLEY, 4” Idler
8 7091497 2 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
9 7035728 1 BRACKET, Fixed Idler used on 33” Deck Models only
10 7036526 1 BRACE, Fixed Idler Bracket used on 33” Deck Models only
11 7090858 5 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
12 7046567 1 HANDLE, Blade Engagement (Flip)
13 7010740 2 RING, 2” External Retaining
14 7090037 3 PIN, 3/32 x 3/4” Cotter
15 7036521 1 SPRING, Extension, 4” x 1/2” Diameter
16 7047787 1 WELDMENT, Idler Arm
17 7014314 1 SPACER, .39 x 1.0 x .31 Nylon
18 7046874 1 GRIP, Handle
19 7091514 2 WASHER, 3/8” Flat
20 7035378 1 DRUM, Brake Spindle
21 7014304 1 PIN, 1/4 x 1-5/8” Clevis
22 7034852 1 BAND, Brake (Formed)
23 7090122 2 WASHER, 3/8” Flat SAE
24 7090055 4 WASHER, 1/4” Flat
25 7046677 1 EYE-BOLT, 1/4-20 x 4”
26 7046648 1 SPRING, Torsion, Flip Handle
27 7091974 1 PIN, 3/16 x 1” Clevis
28 7059254 1 WELDMENT, Blade Engagement Handle
29 7014168 1 SPRING, Blade Handle
30 7012055 1 ROD, Idler Control
31 7090299 1 SCREW, #10-32 x 1” Hex Washer Head Self-Tap
32 7018524 1 SWITCH, Deck Interlock (NO)
33 7038021 1 MOUNT, Handle/Switch
34 7090362 2 SCREW, 1/4-20 x 5/8” Hex Washer Head Self-Tap
35 7090555 1 PIN, 3/32 x 1/2” Cotter
36 7090761 1 NUT, 1/4-20 Hex Top Lock
tionItem Qt
Note
Footnotes:
Note: * Belt part numbers are printed on belts.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
37
TP 400-5003-5-RE-N
BELTS, BRAKES, INTERLOCK
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
38
SERIES 23
BELTS, BRAKES, INTERLOCK
p
y
Part No Descri
37 7014343 1 BUSHING, Flange .27 x .35 x .4
38 7046782 1 SPRING, Rectangular Wire Die, Blue
39 7032111 1 RESTRICTOR, Belt
tionItem Qt
Note
Footnotes:
Note: * Belt part numbers are printed on belts.
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
39
TP 400-5003-5-RE-N
RAILS, LIFT ARMS, CAM LIFT
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
40
SERIES 23
RAILS, LIFT ARMS, CAM LIFT
p
y
Part No Descri
1 7091503 2 HAIR PIN, 3/32 x 1-1/2”
2 7028200 2 SWIVEL, Adjustable
3 7028728 2 ADJUSTER, Chain (5/16-18 thread)
4 7091297 2 NUT, 5/16-24 Hex or 7090223
5 7090854 1 NUT, 3/8-24 Hex Nyloc
6 7090122 1 WASHER, 3/8” Flat SAE
7 7034213 1 PIVOT, Leveling
8 7059324 1 WELDMENT, Rear Lift Arm
9 7090483 1 SCREW, 3/8-24 x 1-3/4” Hex Head Cap, GR 5
10 7032030 2 WASHER, 13/32 x 1-1/4” Flat
11 7046155 1 LEVER, Height of Cut
12 7090289 1 NUT, 3/8-24 Hex Center Lock
13 7046159 1 SPRING, Lever
14 7012068 2 RING, Rear Lift Arm (Blue)
15 7031855 1 GUIDE, Belt
16 7046163 2 SPRING, Assist
17 7031838 1 BRACE, Top
18 7016122 1 ROD, Leveling (3/4-24 thread)
19 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
20 7058969 1 ASSEMBLY, Clutch Plate
21 7043848 1 RAIL, Deck Lift, Right Hand
22 7073269 1 RAIL, Deck Lift, Left Hand
23 7046157 1 DETENT, Height Adjust
24 7090324 2 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
25 7046217 1 SPACER, Detent
26 7091198 3 SCREW, 3/8-16 x 5/8” Hex Washer Self-Tap
27 7026420 1 GRIP, Height Adjustment Lever
28 7012067 2 RING, Front Lift Arm (Red)
29 7032997 1 ARM, Front Lift
30 7058041 1 WELDMENT, Front Lift Arm
31 7090365 1 PIN, 1/8 x 3/4” Cotter
32 7022717 1 ROD, Deck Support (Front Lift Arm to Front End)
33 7017847 1 RING, .438 External Retaining
34 7090858 2 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
35 7071920 2 SPACER, Deck Lift
36 7092051 1 BOLT, #10-24 x 1” Flat Head Square Neck
37 7091290 1 NUT, #10-24 Hex Nyloc
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
41
TP 400-5003-5-RE-N
RAILS, LIFT ARMS, CAM LIFT
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
42
SERIES 23
RAILS, LIFT ARMS, CAM LIFT
p
y
Part No Descri
38 7032243 1 ANCHOR
39 7090233 2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5
40 7090391 2 WASHER, 5/16” Internal Tooth Lock
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
43
TP 400-5003-5-RE-N
BLADE STOP PEDALS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
44
SERIES 23
BLADE STOP PEDALS
p
y
Part No Descri
1 7073267 1 FOOT PEDAL, Blade Stop Control
2 7074649 1 SPRING, Latching (.072 dia.) replaces 7035669 (.062 dia.)
3 7015448 1 SPRING, Pedal
4 7015495 1 SHOULDER BOLT, 3/8-24 w/Nylon Patch, GR 5
5 7015446 1 SHOULDER BOLT, 3/8-24 x 9/16”
6 7032030 1 WASHER, Flat 13/32” ID x 1.25” x 1/8” Thick ZP was 7012063
7 7091630 1 NUT, 3/8-24 Hex, GR B was 90155
8 7090250 2 WASHER, 1/2” Flat SAE
9 7090289 1 NUT, 3/8-24 Hex Center Lock
10 7091584 1 NUT, 1/4-20 Hex Flange Lock, GR 5
11 7073216 1 CABLE ASSEMBLY, No Reverse in Mow
12 7073217 1 CLIP, Cable
13 7091530 1 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR 5 was 91776
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
45
TP 400-5003-5-RE-N
SPINDLE
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
46
SERIES 23
SPINDLE
p
y
Part No Descri
1 7054531 1 ASSEMBLY, Spindle Housing (Incl. items 2 thru 9A & 10 thru 13) used on 33” deck
1 7058049 1 ASSEMBLY, Spindle Housing (Incl. items 2 thru 8 & 9B thru 11) used on 28” & 30” decks
2 7012491 2 RING, 1.85” Internal Retaining
3 7013313 2 BEARING, Spindle
4 7040460 1 WELDMENT, Spindle Housing
5 7010817 1 LUBE FITTING, 3/16” Press-In
6 7044785 1 SPINDLE, Rider (10.327” overall length)
7 7010935 1 WASHER, .77 x 1.13 x .06 Flat
8 7014407 1 WASHER, Spindle
9A 7037751 1 HOLDER, Blade used on 33” deck
9B 7031184 1 HOLDER, Blade used on 28” & 30” decks
10 7044782 1 SPACER, Blade Centering
11 7090356 1 NUT, 5/8-18 Hex Center Lock Jam
12 7090491 2 SCREW, 1/2-20 x 1-1/4” Hex Head Cap, GR 5
13 7091939 2 NUT, 1/2-20 Hex, GR 5 or B
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
47
TP 400-5003-5-RE-N
DECALS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
48
SERIES 23
DECALS
p
y
Part No Descri
1 7071916 1 DECAL, SNAPPER
2 7023982 1 DECAL, OHV (33” Kohler Engine Models)
3 7023980 1 DECAL, Back-Up Recoil (33” Kohler Engine Models)
4 7046218 1 DECAL, Height of Cut
5 7026831 1 DECAL, Danger (CPSC)
6 7046720 1 DECAL, Chute/Deflector Warning
7 7023996 1 DECAL, 28 Inch (Hi-Vac)
8 7023997 1 DECAL, 30 Inch
9 7022991 1 DECAL, 33 Inch (Hi-Vac)
10 7015691 1 DECAL, Battery Caution
11 7012358 1 DECAL, Battery
12 7029113 1 DECAL, Caution, Fuel (English)
13 7074481 1 DECAL, No Mow in Reverse
14 7046440 1 DECAL, Safety Instructions
15 7101111 1 DECAL, Warning, Safety Panel
16 7075607 1 DECAL, Service Parts, Domestic
17 7101109 1 DECAL, Remove Battery
18 7101112 1 DECAL, Danger, Safety Panel
19 7101107 1 DECAL, Caution, Fuel
20 7101108 1 DECAL, Caution, Battery
21 7101110 1 DECAL, Danger, Deck
-- -- 1 DECAL, Patent Numbers not shown, not a service part
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
49
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (For 9, 11 & 11.5HP Briggs Recoil)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
50
SERIES 23
ELECTRICAL SYSTEMS (For 9, 11 & 11.5HP Briggs Recoil)
p
y
Part No Descri
1 7063064 1 INTERLOCK MODULE, Briggs was 28606
2 7028386 1 HARNESS (Deck Interlock Wiring)
3 7018524 1 SWITCH, Deck Interlock (NO)
4 7090880 1 WASHER, 5/8” Internal Tooth Lock
5 7015438 1 NUT, 5/8-32 Hex
6 7011138 1 IGNITION KEY, Pair
7 7073714 1 HARNESS, Ground (Recoil Start)
8 7012080 3 CABLE TIE, 7”
9A 7029211 1 SWITCH, Seat, Quick Mount (NC) used on 11 & 13 HP Engines
9B 7023354 1 SWITCH, Seat (NC) used on 11-1/2 HP Engines
10 7017817 1 SWITCH, Ignition (2-Pole) (Recoil Start)
11 7022886 1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
12 7028607 1 HARNESS, Operator Presence Control (OPC) Wire
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
51
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (For 10, 11, 12, 12.5 & 13HP Briggs)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
52
SERIES 23
ELECTRICAL SYSTEMS (For 10, 11, 12, 12.5 & 13HP Briggs)
p
y
Part No Descri
1 7060753 1 KIT, 12 Volt Dry Charge Battery, 220 CCA
2 7075671 1 SOLENOID, Super-Trombetta replaces 7018817
3 7022788 1 HARNESS, Starter Wiring (Briggs Engines)
4 7073715 1 HARNESS, Ignition Wiring (Briggs Engines)
5 7016168 1 HOLDER, Fuse (Includes Fuse)
-- 7016169 1 FUSE, 10 Amp (Not shown)
6 7063064 1 INTERLOCK MODULE, Briggs was 28606
7 7028386 1 HARNESS (Deck Interlock Wiring)
8 7018524 1 SWITCH, Deck Interlock (NO)
9 7012444 1 COVER, Battery Cable
10 7019326 1 WIRE, Positive (Red, 17” long)
11 7073797 1 SWITCH, Ignition, 4 Terminal, Indak
12 7090880 1 WASHER, 5/8” Internal Tooth Lock
13 7015438 1 NUT, 5/8-32 Hex
14 7011138 1 IGNITION KEY, Pair
15 7090539 3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
16 7022886 1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
17 7091576 4 NUT, 1/4-20 Hex, GR 5 or B
18 7090053 2 WASHER,1/4” Internal Tooth Lock
19 7027172 2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR 5
20 7028027 1 WIRE, Negative, Black (15” long)
21 7028607 1 HARNESS, Operator Presence Control (OPC) Wire
22 7091576 1 NUT, 1/4-20 Hex, GR 5 or B
23 7012080 2 CABLE TIE, 7”
24 7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
25 7014451 1 CABLE TIE
26A 7029211 1 SWITCH, Seat (NC) used on 11 & 13HP Engines
26B 7023354 1 SWITCH, Seat (NC) used on 12.5 & 13 HP Briggs
tionItem Qt
Note
only
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
53
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (For 13.5, 15, 16 & 17HP Briggs)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
54
SERIES 23
ELECTRICAL SYSTEMS (For 13.5, 15, 16 & 17HP Briggs)
p
y
Part No Descri
1 7060753 1 KIT, 12 Volt Dry Charge Battery, 220 CCA
2 7075671 1 SOLENOID, Super-Trombetta
3 7022788 1 HARNESS, Starter Wiring (Briggs)
4 7074406 1 HARNESS, Ignition Wiring (Briggs)
5 7016168 1 HOLDER, Fuse (Includes Fuse)
-- 7016169 1 FUSE, 10 Amp (Not shown)
6 7063064 1 INTERLOCK MODULE, Briggs & Kohler was 28606
7 7028386 1 HARNESS (Deck Interlock Wiring)
8 7018524 1 SWITCH, Deck Interlock (NO)
9 7012444 1 COVER, Battery Cable
10 7019326 1 WIRE, Positive (Red, 17” long)
11 7026343 1 SWITCH, Ignition-Afterfire Solenoid
12 7090880 1 WASHER, 5/8” Internal Tooth Lock
13 7015438 1 NUT, 5/8-32 Hex
14 7011138 1 IGNITION KEY, Pair
15 7090539 3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
16 7022886 1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
17 7091576 4 NUT, 1/4-20 Hex, GR 5 or B
18 7090053 2 WASHER,1/4” Internal Tooth Lock
19 7027172 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5
20 7028027 1 WIRE, Negative, Black (15” long)
21 7028675 1 HARNESS, Operator Presence Control (OPC) Wire
22 7091576 4 NUT, 1/4-20 Hex, GR 5 or B
23 7012080 2 CABLE TIE, 7”
24 7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
25 7014451 1 CABLE TIE
26 7012485 2 RETAINER, 1/4” Bolt
27 7023354 1 SWITCH, Seat (NC) for use with 7075071 seat
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
55
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (For 11 & 13HP Honda)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
56
SERIES 23
ELECTRICAL SYSTEMS (For 11 & 13HP Honda)
p
y
Part No Descri
1 7060753 1 KIT, 12 Volt Dry Charge Battery, 220 CCA
2 -- 1 SOLENOID (not shown, part of engine) No Snapper part number.
3 7054589 1 HARNESS, Starter Wiring (Honda)
4 7074962 1 HARNESS, Ignition Wiring
5 7014451 1 CABLE TIE, 3.19” long
6 7063064 1 INTERLOCK MODULE, Briggs & Kohler was 28606
7 7028386 1 HARNESS (Deck Interlock Wiring)
8 7018524 1 SWITCH, Deck Interlock (NO)
9 7012444 1 COVER, Battery Cable
10 7023354 1 SWITCH, Seat (NC)
11 7073797 1 SWITCH, Ignition, 4 Terminal, Indak
12 7090880 1 WASHER, 5/8” Internal Tooth Lock
13 7015438 1 NUT, 5/8-32 Hex
14 7011138 1 IGNITION KEY, Pair
16 7022886 1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
19 7027172 2 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR 5
20 7028027 1 WIRE, Negative, Black (15” long)
21 7074963 1 HARNESS, Operator Presence Control (OPC) Wire
23 7012080 2 CABLE TIE, 7”
24 7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
25 7012485 2 RETAINER, 1/4” Bolt
tionItem Qt
Note
Purchase from engine
manufacturer.
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
57
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (For 15HP Kohler)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
58
SERIES 23
ELECTRICAL SYSTEMS (For 15HP Kohler)
p
y
Part No Descri
1 7060753 1 KIT, 12 Volt Dry Charge Battery, 220 CCA
2 7075671 1 SOLENOID, Super-Trombetta replaces 7018817
3 7019321 1 HARNESS, Starter Wiring (Kohler Engines)
4 7074405 1 HARNESS, Ignition Wiring (15HP Kohler Engines)
5 7016168 1 HOLDER, Fuse (Includes Fuse)
-- 7016169 1 FUSE, 10 Amp (Not shown)
6 7063064 1 INTERLOCK MODULE, Briggs & Kohler was 28606
7 7028386 1 HARNESS (Deck Interlock Wiring)
8 7018524 1 SWITCH, Deck Interlock (NO)
9 7012444 1 COVER, Battery Cable
10 7019326 1 WIRE, Positive (Red, 17” long)
11 7073797 1 SWITCH, Ignition, 4 Terminal, Indak
12 7090880 1 WASHER, 5/8” Internal Tooth Lock
13 7015438 1 NUT, 5/8-32 Hex
14 7011138 1 IGNITION KEY, Pair
15 7090539 3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
16 7022886 1 SWITCH, Operator Presence Control (OPC) Traction (NC/NO)
17 7091576 1 NUT, 1/4-20 Hex, GR 5 or B
18 7090053 2 WASHER,1/4” Internal Tooth Lock
19 7027172 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5
20 7028027 1 WIRE, Negative, Black (15” long)
21 7028678 1 HARNESS, Operator Presence Control (OPC) Wire
22 7091576 1 NUT, 1/4-20 Hex, GR 5 or B
23 7012080 2 CABLE TIE, 7”
24 7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
25 7014451 1 CABLE TIE, 3.19” long
26 7012485 2 RETAINER, 1/4” Bolt
27 7029211 1 SWITCH, Seat (NC)
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
59
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (Briggs Magneto Ground)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
60
SERIES 23
ELECTRICAL SYSTEMS (Briggs Magneto Ground)
p
y
Part No Descri
-- -- View shows engine magneto ground connection on throttle plate
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
61
TP 400-5003-5-RE-N
ELECTRICAL SYSTEMS (Kohler Magneto Ground)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
62
SERIES 23
ELECTRICAL SYSTEMS (Kohler Magneto Ground)
p
y
Part No Descri
-- -- View shows engine magneto ground area
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
63
TP 400-5003-5-RE-N
WIRING SCHEMATIC (9, 11 & 11.5HP Recoil Start Briggs)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
64
SERIES 23
WIRING SCHEMATIC (9, 11 & 11.5HP Recoil Start Briggs)
p
y
Part No Descri
-- -- Wiring Schematic incl. harness #'s 7028386, 7073714 & 7028607
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
65
TP 400-5003-5-RE-N
WIRING SCHEMATIC (10, 11, 12, 12.5 & 13 HP Briggs)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
66
SERIES 23
WIRING SCHEMATIC (10, 11, 12, 12.5 & 13 HP Briggs)
p
y
Part No Descri
-- -- Wiring Schematic incl. harness #'s 7022788, 7073715 & 7028607
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
67
TP 400-5003-5-RE-N
WIRING SCHEMATIC (13.5, 15, 16 & 17 HP Briggs Engines)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
68
SERIES 23
WIRING SCHEMATIC (13.5, 15, 16 & 17 HP Briggs Engines)
p
y
Part No Descri
-- -- Wiring Schematic incl. harness #'s 7022788, 7074406, 7028675
& 7015430
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
69
TP 400-5003-5-RE-N
WIRING SCHEMATIC (11 & 13 HP Honda Engines)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
70
SERIES 23
WIRING SCHEMATIC (11 & 13 HP Honda Engines)
p
y
Part No Descri
-- -- Wiring Schematic incl. harness #'s 7054589, 7074962, 7028386
& 7074963
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
71
TP 400-5003-5-RE-N
WIRING SCHEMATIC (14 & 15 HP Kohler Engines)
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
72
SERIES 23
WIRING SCHEMATIC (14 & 15 HP Kohler Engines)
p
y
Part No Descri
-- -- Wiring Schematic incl. harness #'s 7019321, 7074405, 7028386
& 7028678
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
73
TP 400-5003-5-RE-N
HARDWARE BAGS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
74
SERIES 23
HARDWARE BAGS
p
y
Part No Descri
-- 7063039 1 HARDWARE BAG (Incl. the 17 items below) for manual start models
7011024 2 PLUG, 1/2” Cup Insert
7013321 2 BUSHING, Tie Rod
7013849 2 SPACER, .33 x .63 x .156
7013862 1 ROLL PIN, 1/4 x 1-1/2”
7023667 1 FOAM COVER, Steering Shaft
7023671 1 COVER, Steering Shaft
7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
7091038 4 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
7091516 2 PIN, 5/32 x 1” Cotter
7090296 1 PIN, 3/16 x 1” Cotter
7090122 2 WASHER, 3/8” Flat SAE
7075018 2 BRACKET, Seat
7091714 4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5
7023735 2 KNOB, Seat Adjusting, 5/16-18 thread
7011791 4 RETAINER, 5/16” Bolt
7023354 1 SWITCH, Seat (NC)
7090951 2 NUT, 5/16-18 Hex Large Flange Center Lock
-- 7061872 1 HARDWARE BAG (Includes the 15 items below)
7011024 2 PLUG, 1/2” Cup Insert
7013321 1 BUSHING, Tie Rod
7013849 2 SPACER, .33 x .63 x .156
7013862 1 ROLL PIN, 1/4 x 1-1/2”
7023667 1 FOAM COVER, Steering Shaft
7023671 1 COVER, Steering Shaft
7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B
7091038 2 BOLT, 5/16-18 x 1/2” Hex Flange Nyloc
7091516 2 PIN, 5/32 x 1” Cotter
7090296 1 PIN, 3/16 x 1” Cotter
7090122 1 WASHER, 3/8” Flat SAE
7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
7023191 2 KNOB, Seat Adjusting (5/16-18 thread)
7028395 2 SPACER, Pivot
7029211 1 SEAT SWITCH, Quick Mount (NC)
-- 7063292 1 HARDWARE BAG (Incl. items 1-12 above & the 6 items below)
7023735 2 KNOB, Seat Adjusting, 5/16-18 thread
7023354 1 SWITCH, Seat (NC)
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
75
TP 400-5003-5-RE-N
HARDWARE BAGS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
76
SERIES 23
HARDWARE BAGS
p
y
Part No Descri
7075018 2 BRACKET, Seat
7091714 4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5
7011791 4 RETAINER, 5/16” Bolt
7090951 2 NUT, 5/16-18 Hex Large Flange Center Lock
-- 7061093 1 HARDWARE BAG (Incl. the 9 items below)
7017176 1 DECAL, Recycling Speeds
7017328 1 DECAL, Height of Recycling Cut
7022325 1 DECAL, Cut Height
7090001 3 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
7090188 3 WASHER, 5/16” Flat
7090392 2 SCREW, 1/2-20 x 1” Hex Head Cap, GR 5
7090492 3 WING NUT, 5/16-18
7090509 2 WASHER, 1/2” Internal Tooth Lock
7090559 2 NUT, 1/2-20 Hex Jam
tionItem Qt
Note
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
77
TP 400-5003-5-RE-N
ACCESSORIES & ATTACHMENTS
Manual No. 7006152 REAR ENGINE RIDER
TP 400-5003-5-RE-N
78
SERIES 23
ACCESSORIES & ATTACHMENTS
p
y
Part No Descri
7060325 KIT, Drive Disc Puller used on All RER Aluminum
7060697 KIT, Dump Cart
1692125 KIT, Dump Cart (10 Cu. Ft.)
7061400 KIT, Gage Wheel (28” & 33”)
7060794 KIT, Gage Wheel (41” & 42”)
7060941 KIT, Single Bag Catcher (25”)
7060942 KIT, Single Bag Catcher (26” & 30”)
7060943 KIT, Single Bag Catcher (28” & 33”)
7060944 KIT, Single Bag Catcher (41” & 42”)
7063281 KIT, Twin Bag Catcher (28” & 33”)
7061414 KIT, Twin Bag Catcher (European 28” & 33”)
7060945 KIT, Twin Bag Catcher (41” & 42”)
7063125 KIT, Clamshell Bagger (28” & 33”)
7060947 KIT, Bag-N-Wagon (28” & 33”)
7060948 KIT, 28” Thatcherizer used on All series 7 & Newer
7060964 KIT, Wagon Cover (28” & 33”)
7072416 KIT, Front Weight used on All series 7 & Newer
7060959 KIT, 36” Dozer Blade
7060653 KIT, Tire Chains (16 x 6.50-8 Tires)
7060049 KIT, Tire Chains (16 x 4.50-8 Tires)
7061823 KIT, Ninja Recycling Cover (25”) includes 7029143 (25” Ninja
7061049 KIT, Recycling Cover (25”) includes 7016967 (25” mulching
7061253 KIT, Ninja Recycling Cover (28”)
7061254 KIT, Ninja Recycling Cover (30”)
7061255 KIT, Ninja Recycling Cover (33”)
7061987 KIT, Ninja Recycling Cover (41” & 42”)
7061915 KIT, 24” x 36” Tow Behind Poly Lawn Roller
tionItem Qt
Note
Drive Discs
Models
Models
blade)
blade)
Footnotes:
Manual No. 7006152REAR ENGINE RIDER
SERIES 23
79
TP 400-5003-5-RE-N
Parts Manual fo
r
REAR ENGINE RIDER
SERIES 23
IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION
TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
McDonough, GA, 30253 U.S.A.
Revision 5,
8/24/2007
Manual No. 7006152
TP 400-5003-5-RE-N
Loading...