Snapper 2800 GT, 1800 GT, 2700 YT, 1700 YT User Manual
1
Installation
Instructions
Hitch & Tube Group
Mfg. No. 1694692
For Prestige / 2800 / 1800 / GT Series Garden Tractors
For Conquest / 2700 / 1700 / YT Series Yard Tractors
Figure 1. Contents
Kit Contents:
Ref. Part No. Qty. Description
1 1679896 1 CLAMP, Hose 6", Band Type
2 1679895 1 HOSE, Vac Col, 6 x 12
3 1930531 4 SCREW, Truss Head Phillips,
#10-32 x 1/2
4 1910531 4 WASHER, #10-32
5 1928919 4 NUT, Hex Washer Assembly,
#10-32
6 1675766 1 DECAL, Cleaning Instructions
7 1700773 1 TUBE & DECAL ASSEMBLY
(Includes Ref. No. 6)
8 1921210 4 CAPSCREW, Hex Head,
3/8-16 x 1
9 1727132 1 BRACKET, RH
10 1727133 1 BRACKET, LH
11 1930651 4 NUT, Hex Centerlock, 3/8-16
12 1960268 6 CARRIAGE BOLT,
3/8-16 x 1-1/4
13 1919439 6 NUT, Nylock, 3/18-16
14 1724807 1 CROSS BAR
15 1725599 1 HITCH, Inner
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
WARNING
HITCH INSTALLATION
NOTE: Do not tighten hardware until all components are
installed.
1. Mount the left and right hitch brackets (B & D, Figure
2) to the rear frame wrapper (E). Secure with four
3/8-16 x 1 capscrews (A) and 3/8-16 locknuts (C).
Figure 2. Hitch
A. Capscrew, 3/8-16 x 1 D. Hitch Bracket, LH
B. Hitch Bracket, RH E. Rear Frame Wrapper
C. Locknuts, 3/8-16 (Tractor)
A
B
C
D
A
E
1
11
2
3
6
5
4
8
9
15
14
13
12
13
10
12
8
7
2
Installation Instructions Hitch & Tube Group
Form No. 1727434-00
Rev. 07/2004
© 2004 Simplicity Manufacturing, Inc. All Rights Reserved
TP 200-4128-00-AT-SMAN
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
Figure 4. Discharge Tube Installation
A. Decal E. Truss Head Screw
B. Discharge Tube F. Hose
C. Locknut, Hose G. Clamp
D. Washer H. Turbo Discharge
G
H
F
A
B
C
D
E
F
G
2. Connect the inner hitch (B, Figure 3) to the cross bar
hitch (C) using 3/8-16 x 1-1/4 carriage bolts (D) and
3/8-16 locknuts (A).
3. Connect the cross bar hitch (C) to the brackets (E)
using 3/8-16 x 1-1/4 carriage bolts (D) and 3/8-16
locknuts (A).
4. Tighten all hardware.
DISCHARGE TUBE ASSEMBLY
1. Connect the flexible hose (F, Figure 4) and clear
plastic discharge tube (B). The two should overlap
by approximately 2”.
2. Secure the tubes using truss head screws (E), washers (D), and locknuts (C). Insert the screws from the
inside out and poke them through the flexible hose.
3. Insert the upper end of the clear tube into the cart
sleeve. Slide the flex hose (F) over the turbo (H) and
secure with the large hose clamp (G). The hose
should overlap the turbo discharge by 2”-3”.
The clamp screw should be positioned to the inside
as shown to prevent accidental impact and removal
of the clamp.
Check that the upper end of the clear tube (B, Figure
4) is not contacting the top of the collector cover. If
necessary, cut off the clear tube flush with the connecting sleeve (See Wide Body Cart Operators
Manual).
Figure 3. Hitch Installation
A. Locknut,3/8-16 D. Carriage Bolt, 3/8-16 x 1-1/4
B. Inner Hitch E. Bracket
C. Cross Bar Hitch
D
C
A
B
A
D
E
E
Loading...