Snapper 2730 User Manual
INSTALLATION
PARTS LIST
Mounted on
mqyer deck.
INSTRUCTIONS
_
VAClJubI COL&CTQ~P @APTfJe~
MFG. NO. 1691170 FOR 42”MOWERS
MFG. NO. 1691009
&
1691182
MFG. NO. 1691171 FOR 48” MOWERS
MFG. NO. 1690986
WARNING
A
The adapter is part of the
A
YBCUU~
collector system.
&
1691193
Do not operate unless the adapter and entire
YBEUU~
is removed,
collector are installed. If vacuum collector
remove the adapter and be sure mower
deflector is In original position.
WARNING
A
Shut off tractor engine and
remove
key before
installing or removing the adapter.
hardware for,
48” mower.
NOTE
Deflector brace (F, figure 1) and adaptor holddown (R) are preassembled to adaptor (0) with
rivets (G).
Figure 1.
Ref.
Qty.
Description
A 1 Nut,
8 1
c 1 Washer,
D 1
E 1
1
F 1
G 6
H 1 Nut,
I 1 Washer,
J 1
K 1 Spring Latch 1678786
L 1 Nut.
M 1
N 1 Washer.
0
1
1
P 1 Washer. 7116 1817378
cl 1
R
1 Hold-down, Adaptor 1679548
3/8-l
Lockwasher.
Spacer
Bolt, Carriage,
(42”)
Bolt, Carriage. 3/8-16x
(48”)
Deflector Brace
Rivet
Bolt. Carriage,
Lockwasher,
Adaptor Assembly
42” 1678667
48” 1678668
Bolt,
8 1816950
3/S
3/S
3/8-l
6 x
1
l-114
5/16
l/2
3/S-16 x 7/S
5/16
5/l
6
5/l
6 1917642
(Inch. F.
G and
Carraige,
5/16-18
x 1
Part No.
1916965
1919384
153081
1917378
1923220
1700260
928706
1960251
J
960027
1931349
1917372
1917356
RI
1931335
INSTALLATION
1. Refer to figure I to take inventory of required parts.
2. Attach the latch (K, figure 1) to
18 x 1 carriage bolt
(Q),
washer (N), 5/ 16 lockwasher (M) and 5/ 16 nut
3. Install the spacer (D,‘figure l), with hardware shown,
in hole (A, figure 2) in mower deck. Remove existing
hardware. For the 42” adapter, use a
carriage bolt. For the48”adapter,
carriage bolt. For the 42” adapter, use a 3/ 8 washer (B,
figure l), 3/8 lockwasher (M) and 3/8 nut (N)
supplied. For the 48” mower, use existing washer and
nut and the
Figure 2.
A. Install Spacer
8.
InStall Bolt
C. Stone Guard
318
washer (B) supplied.
theadapterwith5/
16-
7/ 16 x I washer (P), 5/ 16
(L).
3/8-16 x 1
usea3/8-16x l-1/4
F&M -
1679272
PRlNTED IN U.S.A.
~
878
4. In the top hole (B, figure 2) of the mower deck, install
the 3/8-16 x 7/8 carriage bolt
washer (I) from bottom. Secure with
(.I,
figure 1) and l/Z”
318
locknut(H)
on top of deck.
5. Raise the mower
deflectori+,install the.;adapier.
6. Hook the adaptor hold-down (R, figure 1) onto the
stone guard (C, figure 2). Then, lift the adaptor up into
place, hooking onto the spacer (D, figure 1). The
spring latch (K) should snap over the carriage bolt(J)
installed on mower deck in step 4.
AWARNING
Shut off the engine and
removing my part of the
REMOVAL
mmve
YBCUU~
key before
collector.
To operate without the vacuum collector, remove the
adapter as follows. Unhook spring latch from bolt in
mower housing and then pull off, unhooking from spacer
and stone guard. Be sure mower deflector is down in
original position.
Loading...