Snapper 216015, 216515BV User Manual

Download

Page 1

Safety Instructions & Operator’s Manual for

21” STEEL DECK

WALK MOWERS

SERIES 15

PUSH

MODELS

216015

216515BV

MODEL NUMBER EXPLANATION

21 65 15 BV

CUTTING WIDTH ENGINE DESIGNATION ENGINE HORSE POWER SERIES DESIGNATION

21 – 21” Cutting Width B – Briggs &Stratton 15 - Series Designation 60 – 6.0 HP (Engine Horse Power) V – Overhead Valve 65 – 6.5 HP (Engine Horse Power)

Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense.

MANUAL No. 7-3689 (I.R. 4/29/00)

Page 2

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerf ul cutting machine is capab le of amputating hand s and feet and can throw objects that can cause injury and damage! Failure to comply with the follow ing SAFETY instru ctions could resu lt in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Ch ildren are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

1. KEEP children out of the mowing area and under the watchful care of a responsible adult.

2. DO NOT allow children in yard when mach ine is operated and turn machine OFF if anyone enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature judgment under close adult supervision to operate machine.

5. DO NOT pull mower backwards unless absolutely necessary. LOOK and SEE behind and down for children, pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners, shrubs, trees, or other object s that may obscure vision.

SLOPE OPERATION

1. Slopes are a major factor related to slip and fall accidents, which can result in severe injury. All slopes require extra cau tion. If you feel uneasy on a slope, DO NOT mow it.

2. Mow across slopes, never up-and-down. Exercise extreme CAUTION when changing directions on slopes. DO NOT mow steep slopes or other areas where stability or traction is in doubt.

3. Use extra care with crass catchers or other attachments; these affect the handling and the stability of the machine.

PREPARATION

1. Read, understand, and follow instructions and warnings in this manual and on the mower, engine and attachments. Know the controls and the proper use of the mower before starting.

2. Only mature, responsible persons shall operate the machine and only after proper instruction.

PREPARATION

(Continued From Previous Column)

3. Data indicates that o perators age 60 and abov e, are involved in a large percentage of mowerrelated injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury.

4. Handle fuel wit h ext ra care. Fuels are flammab le and vapors are explosive. Use only an approved fuel container. DO NOT remove fuel cap or add fuel with engine running. Add fuel outdoors only with engine stopped and cool. Clean spilled fuel and oil from machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects such as toys, wire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere with mo win g. Also note the location of holes, stumps, and other possible hazards.

6. Keep people and pets out of the mowing area. Immediately, STOP Blade, Stop engine and Stop mower if anyone enters the area.

7. Check shields, deflectors, switches, blade controls and other safety dev ices frequently for proper operation and location.

8. Make sure all safety decals are clearly legible. Replace if damaged.

9. Protect yourself w hen mowing and wear safety glasses, long pants and substantial footwear. DO NOT mow barefooted or with sandals.

10. Know how to STOP blade and engine quickly in preparation for emergencies.

11. Use extra care when loading or unloading the machine into a trailer or truck.

12. Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or torn spots.

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATION

1. DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area wh ile engine is running.

2. STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of alcohol or drugs.

5. After striking a foreign object or if mower vibrates abnormally, STOP the engine, disconnect and secu re spark plug wire. Inspect the mower for any damage and repair the damage.

6. DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your footing. Keep a firm hold on the handle and walk, never run. Slipping could cause injury.

9. DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE before leaving the operators position for any reason.

10. Before cleaning, repairing or inspecting make certain engine, blade and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.

11. STOP engine and wait until the blade comes to complete STOP before removing grass bag and/or clearing grass.

12. DO NOT operate mower without the entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

13. Slow down before turning.

14. Watch out for traffic when near or crossing roadways.

15. DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

MAINTENANCE AND STORAGE

1. DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2. Keep mower and engine free of g rass, leaves or excess grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts an d screws properly tight. Check that all cott er pins are in proper position.

5. Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, a deadly poison.

6. Service engine and make adjustments only when engine is stopped. Removed spark plug wire from spark p lu g an d secu re w ire away from spark plug to prevent accidental starting.

7. DO NOT change engine governor speed settings or overspeed engine.

8. Check grass bag assembly frequently for wear or deterioration to avoid thrown objects and exposure to moving parts. Replace with new bag if loose seams or tears are ev ident. Rep lace slider or bag adapter if broken or cracked.

9. Mow er blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

10. DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

11. Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

12. Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

Page 4

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS.............................................2 & 3

TABLE OF CONTENTS............................................................................ 4

SECTION 1 - FAMILIARIZATION..............................................................5

SECTION 2 - OPERATING INSTRUCTIONS.........................................6-8

Pre-start Checklist ............................................................................................... 6

Starting & Stopping Engine & Blade............................................................... 6-7

Starting & Stopping Wheel Drive .................................................................... 6-7

Handle Height Adjustment.................................................................................. 7

Cutting Height Adjustment................................................................................ .7

Recycling Operation............................................................................................ 8

Installation of Grass Catcher.............................................................................. 8

SECTION 3 - MAINTENANCE INSTRUCTIONS....................................... 9

Change Engine Oil............................................................................................... 9

Check Mower Blade............................................................................................. 9

Service - Annually................................................................................................ 9

Engine................................................................................................................ 9

Air Filter............................................................................................................. 9

Engine Oil.......................................................................................................... 9

Storage Procedure............................................................................................... 9

SECTION 4 - ADJUSTMENTS AND REPAIR....................................10-11

Mower Blade Replacement ............................................................................... 10

Blade Sharpening .........................................................................................10-11

TROUBLESHOOTING ............................................................................ 12

SERVICE SCHEDULE ............................................................................ 13

Maintenance/Replacement Parts...................................................................... 13

WARRANTY............................................................................................ 14

PRIMARY MAINTENANCE................................................................15-18

Page 5

Section 1 - FAMILIARIZATION

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepar ed for the operators of the SNAPPER WALK BEHIND MOWERS. Its purpose, aside from recommending operating and routine service requirements, is to promote safety through the use of accepted operating practices. Read, Understand and Follow the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3 of this manual and all safety messages on the mower and attachments before operating the mower.

1.2 NOMENCLATURE

The nomenclature drawing above, Figure 1.1, shows the essential parts of the SNAPPER WALK BEHIND MOWERS. It is recommended that all operators of the mower become thoroughly familiar with the controls, parts and operation of the mower before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals befor e operating and keep both handy for future reference.

Page 6

Section 2 - OPERATING INSTRUCTIONS

POSITION)

2.1 PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1. Check guards, deflectors, grass bag, adapter and covers to mak e sure all are in place and securely tightened.

2.1.2. Chec k blade control and wheel drive control to insure they work freely. See Figure 2.1.

RECYCLING MODEL SHOWN (ROPE START MOUNTED ON RIGHT SIDE OF HANDLE)

BLADE CONTROL

FIGURE 2.1

2.1.3. Check cutting height. Adjust to desired height.

2.1.4. Check engine oil and add oil as needed to bring

level up to the full mark. Refer to Engine Owner’s Manual for oil specifications. See Figure 2.2.

FIGURE 2.2

2.1.5. Add fuel to tank after pushing the mower

outside where fumes can saf ely dissipate. Make sure cap is tightened after refueling. Refer to Engine Owners Manual for specifications.

2.1.6. Clean exterior surfaces of cutting deck and engine of any accumulation of spilled fuel, dirt, grass , oil, etc. Keep engine air intake screen and cooling fins clear at all times.

2.2 STARTING & OPERATION

2.2.1. ENGINE & BLADE (Primer Models)

1. Move engine speed control to the “Fast” (Rabbit)

position. See Figure 2.3.

NOTE: Stop the engine (and blade) by releasing the

blade control.

BLADE CONTROL

ENGINE SPEED CONTROL (SHOWN IN “FAST”

2. Push primer bulb three times to start a cold

engine. NOTE: Primer should not be required to restart a hot engine.

3. Pull blade control against handle.

4. Pull rope start handle to crank engine.

5. After engine starts, allow a brief warm-up until

engine runs smooth.

CATCHER MODEL SHOWN (ROPE START MOUNTED ON LEFT SIDE OF HANDLE)

FIGURE 2.3

Page 7

Section 2 - OPERATING INSTRUCTIONS

HEIGHT

2.3 STOPPING

Stop engine and blade by releasing the blade control. Stop forward motion of mower by releasing the wheel drive control.

2.4 HANDLE HEIGHT ADJUSTMENT

The height of the mo wer handle can be adjusted as follows:

1. Loosen the lower nuts on each lower handle as shown in Figure 2.4.

HIGHER

LOWER HANDLE

LOWER

2.5 CUTTING HEIGHT ADJUSTMENT

1. Pull the height adjusting latch outward and move

to desired cutting height. See Figure 2.5.

LOWEST CUTTING

LATCH

HIGHEST CUTTING

LOOSEN LOWER NUTS ON EACH LOWER HANDLE

FIGURE 2.4

2. Move upper mower handle up or down until the

desired position is achieved.

3. Tighten the lower nuts on each lower handle to maintain desired position.

WARNING

Stop engine and mow er blade by releasing the blade control before adjusting cutting height or handle height.

FIGURE 2.5

2. Set all wheels at the same cutting height. The

highest cutting position is Notch 6. The lowest cutting position is Notch 1. See Figure 2.6.

LATCH POSITIONS

CUTTING HEIGHT SETTINGS

FIGURE 2.6

Page 8

Section 2 - OPERATING INSTRUCTIONS

ADAPTER

CONNECTOR

WARNING

2.6 RECYCLING OPERATION (Optional Accessory)

NOTE: For best recycling results, cut up to a m axim um of

1/3 of grass blade length and recycle ONLY when grass is dry.

1. Set all wheels in the highest cutting position (Notch 6).

2. Move engine speed control to “FAST” (Rabbit) position.

3. Move ground speed control to slowest speed setting.

4. Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

2.7 INSTALLATION of GRASS CATCHER

Install grass catcher by sliding connector over f lange of adapter. See Figure 2.7. Attach grass bag hooks over middle handle cross bar. See Figure 2.8.

POSITION BAG BETWEEN HANDLES

SLIDE CONNECTOR DOWN OVER BAG ADAPTER FLANGE

BAG

FIGURE 2.7

ATTACH BAG HOOKS OVER MIDDLE HANDLE

MIDDLE HANDLE CROSS BAR

FIGURE 2.8

Page 9

Section 3 – MAINTENANCE

40 FT. LBS.

3.1 INTRODUCTION

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.

3.2 SERVICE - AFTER FIRST 5 HOURS

3.2.1. CHANGE ENGINE OIL

WARNING

1. Refer to Engine Manual for proper oil

specifications and procedures.

2. For simplest/cleanest oil change, loosen lower handle wing nuts and stand mower up on lower handle as shown in Figure 3.1. Drain oil through dipstick tube into a container.

FIGURE 3.1

3.2.2. CHECK MOWER BLADE

1. Disconnec t spark plug wire and secure end away

from plug.

2. Tilt m ower up on its rear wheels for access to the blade cap screw. Do not tilt m ower with spark plug or carburetor down. See Figure 3.2.

3. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs. See Figure 3.2.

4. Check blade for sharpness, wear and damage. Refer to Section “BLADE WEAR LIMITS”.

FIGURE 3.2

3.3 SERVICE - ANNUALLY

Perform all maintenance as described in the “Service Schedule” section of this manual.

3.3.1. Engine

Service engine according to engine owner’s manual.

3.3.2. Air Filter Refer to engine owner’s manual for service instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1. Drain f uel from fuel tank and let engine run until all fuel is out of the carburetor.

2. Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!

3. Tape all openings closed to prevent spraying

water into exhaust or air intakes during washing.

4. Tilt m ower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of gr ass with a putty knife and or wire brush.

5. Lubricate all exposed m etal with a light coating of oil to prevent corrosion.

6. On self-propelled models, loosen wing nuts on ground speed control rod before folding handles.

7. Loosen handle k nobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8. Store the mower in a shed or other dry area, protected from weather.

RECOMMENDED BLADE RETAINING CAP SCREW TORQUE VALUE SHOULD BE 30 TO

Page 10

Section 4 - REPAIR & ADJUSTMENTS

FLANGES

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.1 MOWER BLADE REPLACEMENT

4.1.1. STANDARD BLADE WEAR LIMIT

1. Inspect blade frequently for signs of exces sive wear

or damage. See Figure 4.1.

4.1.1A. NINJA BLADE WEAR LIMIT 1A. Inspect blade frequently for signs of excessive

wear or damage. See Figure 4.2.

NEW BLADE

WEAR LIMIT (NOTCH STARTS)

DANGEROUS CONDITION ! DO NOT USE ON MOWER ! REPLACE WITH NEW BLADE.

FIGURE 4.1

WEAR LIMIT. CRACKS OR NOTCHES BEGIN TO APPEAR ON TIP

2. Replace the blade if it is badly chipped, bent,

noticeably out of balance or has cracks or notch in either tip. See Figure 4.1 & 4.2. Replace with new blade.

DO NOT use a cutting blade that shows signs of excessive wear or damage. Refer to Section “MOWER BLADE REPLACEMENT” for proper blade inspection and service procedures.

4.1.2. BLADE SHARPENING

1. Dis connect spark plug wire and secure end away

from plug.

IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occ ur, the air f ilter will have to be replaced.

2. Tilt mower up on its rear wheels. Do not tilt mower with spark plug or carburetor down.

3. Remove blade. See Figure 4.3.

WARNING

BLADE HUB

FLANGE

BLADE

CONE WASHER (Concave Side Up)

MAKE SURE THAT BLADE HUB IS SEATED BETWEEN

CAPSCREW

FIGURE 4.3

DANGEROUS ! DO NOT USE A BLADE IN THIS CONDITION !

FIGURE 4.2

Page 11

Section 4 - REPAIR & ADJUSTMENTS

BLADE ASSEM BLY

WARNING

4. Sharpen blade on a grinding wheel at an angle of

22 to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN BEYOND ORIGINAL CUTTING EDGE

ORIGINAL CUTTING EDGE

5. Check blade for balance. If necessary, correct

balance by grinding heavy end of blade.

6. Reinstall blade. See Figure 4.3. Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs.

22-28º

BLADE TIP

END VIEW OF

FIGURE 4.4

Page 12

TROUBLESHOOTING

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.

Using Recoil Starter 2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for

3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.

Engine Stalls or Stops

After Running

2. Choke control in the “CHOKE” position. 2. Move choke control to “OFF” position.

3. Fuel tank empty. 3. Fill with fuel to proper level.

4. Engine air pre-cleaner and or air cleaner dirty. 4. Clean free of all debris.

5. Spark plug defective or gap set improperly. 5. Service spark plug.

6. Water, debris or stale fuel in fuel system. 6. Drain and clean fuel system.

Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty 1. Clean or replace filters.

2. Spark plug faulty. 2. Service spark plug.

3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.

Excessive Vibration 1. Damaged, out of balance or bent mower blade. 1. Service mower blade.

2. Loose blade components. 2. Service and tighten loose parts.

3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.

Cutting Grass

Improperly

Poor Grass Discharge

Oil Leaking

1. Blade control is released or is not being held securely against handle.

1. Cutting height too low or high. 1. Adjust cutting height.

2. Engine speed too slow. 2. Move engine speed control to “FAST” position.

3. Forward ground speed too fast. 3. Move ground speed control to a slower speed.

4. Terraced cut, side to side. 4. Adjust height of cut with height adjust levers.

5. Excessive deck pitch, front to rear. 5. Adjust height of cut with height adjust levers.

6. Cutting blade dull or damaged. 6. Sharpen cutting edges or replace blade.

1. Engine speed too slow. 1. Move engine speed control to “FAST” position.

2. Forward speed too fast. 2. Move ground speed control to a slower speed.

3. Grass is wet. 3. Mow when grass is dry.

4. Excessively worn or damaged blade. 4. Service mower blade.

5. Build up of grass clippings and debris under deck. 5. Clean deck.

6. Improper blade installed on deck.

7. Blade installed improperly on deck. 7. Install blade properly.

1. Leaking engine case.

Instructions.

1. Blade control should be held securely against handle at all times during operation of mower.

6. Install proper SNAPPER blade.

1. Contact authorized SNAPPER dealer.

2. Check and tighten drain plug.

3. Make sure dip stick or oil filler cap is securely in place.

Page 13

ITEM SERVICE PERFORMED

Engine Oil

Check Oil Level Page 6

SERVICE SCHEDULE

REF. EACH

USE 5 HRS

HRS

100

HRS

EACH

SEASON

Air Pre-Cleaner

Air Cleaner Spark Plug

Engine Cooling

System

Mower Blade

Mower Deck

*Change oil every 25 hours when operating under heavy load or high temperatures. **Clean more often under dusty conditions or when air debris is present

4.2 MAINTENANCE/REPLACEMENT PARTS

Initial Oil Change Page 9 Periodic Oil Change Page 9

Clean Sponge Element Engine Manual

& Page 9.

Clean or Replace Engine Manual. Replace Engine Manual. Clean Shroud & Fins Engine Manual

Check For Wear, Damage & Replacement Clean Debris Accumulation

Page 10-11 Page 9

X X*

X**

X** X X**

MAINTENANCE PARTS

Blade Control Cable (See Parts Manual) 7-2933 Cutter Blade (Mulching) 1-7168 Cutter Blade (Not Air Lift Compatible) 2-6691 Cutter Blade (Air Lift Compatible) 1-9795 Cutter Blade (Ninja - Quad Edge) 2-6407 Parts Manual for 21” Steel Deck Walk Behind Mower

Series 12, 14, 15 & 16

06059

Page 14

3 YEAR LIMITED WARRANTY

For three (3) years from pur chase date f or the original pur chaser 's res idential, non-com m erc ial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applic able), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

For ninety (90) days from purchase date for the or iginal purchaser's commercial, rental, or other non-residential use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replacement under this warranty must be paid by the purchaser.

This warranty does not apply to engines and their components , and batteries, as these item s are warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not cover any machine or com ponent part that has been altered or modified changing safety, performance, or durability.

Batteries have a one (1) year prorated warranty period with free replacement if requir ed during the first ninety (90) days from the original purchas e date. SNAPPER will not be responsible for any installation cost incurred. T he battery warranty only covers original equipment batteries and does not cover dam age to the battery or machine caused by neglect or abuse, destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.

There is no other express warranty.

DISCLAIMER OF WARRANTY Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to three (3) years from purchase date for the original purchaser's residential or other non-commercial use, and ninety (90) days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages, under any and all warranties are excluded.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

WARNING: THE USE OF REPL ACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF SUCH PARTS.

IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:

Snapper’s Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253

Page 15

PRIMARY MAINTENANCE

Page 16

PRIMARY MAINTENANCE

Page 17

PRIMARY MAINTENANCE

Page 18

PRIMARY MAINTENANCE

Page 19

NOTES

___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________

Page 20

Safety Instructions & Operator’s Manual for

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR

EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS,

OWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER

21” STEEL DECK WALK BEHIND MOWERS SERIES 15

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand , and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).

WARNING

CHEMICALS KN REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.

WARNING

REPRODUCTIVE HARM.

MANUAL No. 7-3689 (I.R. 4/29/00)

Snapper 216015, 216515BV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual