Snapper 18 Hydro User Manual

Specifications and Main Features

  • MOTOR MAKE: Kohler Command OHV
  • MOTOR MAKE: CH 18S
  • LOSSES POWER: 18 HP At 3600 RPM
  • BORE: 3.03 in. (77mm)
  • STROKE: 2.64 in. (67mm)
  • DISPLACEMENT: 38 cu. in. (624cc)
  • CRANKSHAFT BIULD: Horizontal, Cast Aluminum
  • Electrics:
  • Ignition: Key Ignition Switch
  • Governor: Internal Fly-Weight w/External Adjustment
  • Air Cleaner: Replaceable Paper w/Oiled Foam Pre-Cleaner
  • Lubrication: Pressurized Spray System
  • Oil Capacity: 2 Quarts (1.9L)
  • Tank for Fuel:
  • Material: Non-Corrosive Polyethylene
  • Capacity: 3 Gallons (11.4 L)
  • Type of Transmission: Hydrostatic Pump and Motor
  • Range of speed:
  • Forward: 0 - 7MPH (0-11.3km/h)
  • Reverse: 0 - 4 MPH (0 - 6.4 km/h)
  • Measures:
  • Overall Length: 70 In. (178 cm)
  • Overall Width: 36.9 In. (94 cm)
  • Height: 50.7 In. (127 cm)
  • Weight (approx.): Net: 689 lbs, Shipping: 808 lbs
  • Specifications for Mower:
  • Effective Cutting Width: 48 in. (122 cm)
  • Variable Cutting Height: 1.62" - 3.12" V 4.1-7.9 cm
  • Drive: V-Belt from Tractor PTO Pulley to
  • Blade Arrangement: The Same as Expensive Type as Three Staggered Blades
  • GSP TOW CENTER OF GRAVITY ADJUSTMENT:
  • Full Circle Steering Wheel
  • Clutch: Soft Action V-Belt Clutch
  • Brake: External Band Type

Frequently Asked Questions

Q: What type of oil should I use for the engine?

A: In cold weather conditions, SAE 5W-30 Cold Weather Engine Oil should be utilized, and in temperatures hovering over 32°, SAE 30W should be used instead.

Q: How often should I change the engine oil?

A: For the first five running hours, the engine’s oil will need to be changed after that it is necessary to follow the directions provided in Kohler’s engine manual.

Q: What is the maximum slope for safe operation?

A: Always avoid working on slopes greater than 16.7° and exercise extra caution on slopes greater than 8.5°.

Q: How do I replace the mower blades?

A: Mower blades can be replaced by wedging a wood block in between the blade and the housing so that the blade is prevented from rotating and while a capscrew’s counterclockwise rotation is done to remove it.

Q: What should I do if the engine does not start?

A: It is necessary to ensure that the fuel tank has ample fuel in it, the transmission lever has been set into a neutral position, and the PTO lever is in an ‘off’ position.

Q: How do I check the battery fluid level?

A: It is necessary to clean off dirt located around the battery cap and enveloping the cap until the fluid reaches the split ring’s bottom.

If not, top it with distilled water.

Q: What do I need to do if the tractor moves forward or backward when it is in neutral?

A: In this case, there is a need to ensure that the pump control arm roller is centered onto the marking for the neutral position adjustment, exactly as presented in the manual.

Q: Is it possible for me to jump start the tractor?

A: It is advised against jump starting, however, if it becomes imperative, then the procedures in a manual are followed in order to sustain the equipment from misuse.

User Manual

Page 1
Snapper 18 Hydro User Manual
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
Page 43
Page 44
Page 45
Page 46
Page 47
Page 48
Page 49
Page 50
Page 51
Page 52
Page 53
Page 54
Loading...