Snapper 17GTH-L48, 17GTH-L48 User Manual

Specifications and Main Features

  • Kohler KT17 Engine with 2 Cylinders
  • 17 Horsepower (12.6 kw)
  • 3.125 In. (79.4 mm) bore and 2.75 In (68.95 mm) stroke
  • Combustion Chamber of 48.21 Cu. In (689.2 cc)
  • 15 Amp Flywheel Alternator, 12 Volt electrical system
  • Utilizes Breaker Point Battery Ignition
  • Fuel tank can hold 3 gallons (11.4 L)
  • Make use of Hydrostatic Pump and Motor along with Axial Piston motor with a variable displacement
  • Diive Range: Forwards: 0 to 7 MPH ranging from 0 to 11.3 km/h, Reverse: 0 to 4 MPH ranging from 0 to 6.4 km/h
  • Dimensions: 70 In. (178 cm) in width and 36.9 In. (94 cm) in length and 35.7 In. (91 cm) in height
  • Approx 689 lbs Shipping and 808 lbs of weight
  • Mowing Width of 48 In (122 cm) at the net weight of 135 lbs
  • Vertical belt connected to tractor PTO from Mower Drive
  • Wheel Size: Rear- 23 x 10.50-12 Turf Type, Front- 16 x 6.50-8
  • Inside Tem Rear Tyre Radius of 32 In (81 cm)

Frequently Asked Questions

Q1: Engine of GTH-L Series

A1: The GTH-L series incorporates the use of ottos combustion engines along with rotary engines, more specifically the kohler type.

Q2: What is the horsepower of the GTH-L Series tractor?

A2: This tractor has a power of 17 HP which is 12.6 kw.

Q3: What is the procedure for checking the fuel level inside the tractor?

A3: There is a fuel level gauge that is mounted onto the filler cup of the fuel tank, and this fuel gauge would be used to check the fuel level.

Q4: What is the maximum speed the tractor can achieve?

A4: While moving forward, the maximum speed can be about 7MPH which is 11.3km/h, and 4MPH which is 6.4km/h when moving in reverse.

Q5: What is the cutting width of the mower?

A5: The width of the mower cutting edge is measured at 48 inches or 122 cm.

Q6: Which hydraulic fluid is recommended?

A6: Use of Simplicity Multipurpose Hydraulic/Transmission Oil is encouraged.

Q7: What is the recommended maintenance frequency for the tractor?

A7: Maintenance procedures should be followed regularly as recommended in the manual which is every 25 to 100 hours after use.

User Manual

Page 1
Snapper 17GTH-L48, 17GTH-L48 User Manual
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
Page 40
Page 41
Page 42
Page 43
Page 44
Page 45
Page 46
Page 47
Page 48
Page 49
Page 50
Page 51
Page 52
Page 53
Page 54
Page 55
Page 56
Loading...