Page 1
ATTACHMENT
OPERATOR’S
MANUAL
Snow Plow/Dozer Blade
Mfg. No. Description
1693754 42” Remote Angling Snow Plow/Dozer Blade
Hitch
Mfg. No. Description
1693757 Hitch (for Sovereign / 900 / 2800 Series)
1721303-01
Rev 1/2001
TP 100-2374-01-AT-SMA
Snow/Dozer
Blade & Hitch
Page 2
1
Table of Contents
Maintenance & Normal Care Schedule..............6
Schedule for Normal Care ...............................6
Lubricate the Dozer Blade ...............................6
Adjustments.........................................................7
Skid Shoe Adjustment .....................................7
Spring Tension.................................................7
Lift Height Adjustment .....................................8
Initial Setup & Assembly
Dozer Components..........................................9
Hitch Components .........................................10
Assemble Blade.............................................11
Assemble Lift Rod .........................................12
Install Blade ...................................................12
Install Angling Control Rod ............................13
Attaching & Removing the Hitch & Blade
Removing & Attaching Dozer Blade ..............14
Hardware Identification
& Torque Specifications....................................15
NOTE: In these instructions, “left” and “right” are
referred to as seen from the operating position.
© Copyright 2000 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
TP 100-2374-01-AT-SMA
Recommended Accessories ..............................1
Safety Rules & Information
General Warnings............................................2
Operating on Slopes........................................2
Preparation ......................................................2
Operating Safety..............................................2
Features & Controls ............................................3
Blade Angle Control.........................................3
Attachment Lift.................................................3
General Operating Instructions
Checks Before Starting....................................4
Engine & Ground Speed Selection..................4
Transporting.....................................................4
Starting & Stopping .........................................4
Changing Angle of the Blade...........................5
Dozing Tips......................................................5
Snow Plowing Tips ..........................................5
Storage .................................................................5
Recommended Accessories
For best performance, it is recommended to use tire chains and two rear wheel weights. The maximum weight
added to the tractor should not exceed 35 lbs. per wheel.
For operation on slopes greater than 15% (8.5°), Quick Tach Weights, tire chains, and wheel weights are recommended. Never operate on slopes greater than 17.6% (10°).
Page 3
OPERATING SAFETY
● Always clear snow up and down the face of slopes,
never across the face. Exercise extreme caution
when changing direction on slopes. Do not attempt to
clear steep slopes.
● Exercise extreme caution when operating on, or
crossing, gravel drives, walks or roads. Stay alert for
hidden hazards or traffic.
● After striking an object or if unit starts to vibrate
abnormally, stop the engine and remove the key.
Check for the cause and any damage before restarting. Before any inspection, make sure all moving
parts have stopped.
● Take all possible precautions before leaving operator’s position. Lower the attachment, set the parking
brake, stop the engine and remove the key.
● Never operate near glass enclosures, automobiles,
window wells, dropoffs, etc.
● Do not put hands or feet near or under the dozer
blade. Keep clear of the dozer blade at all times.
● Do not overload machine capacity by attempting to
clear too much material at too fast a rate.
● Never operate unit at high transport speeds on slippery surfaces. Use care when travelling in reverse.
● Never operate the dozer blade without good visibility
or light. Always be sure your feet are properly placed
on the footrests and keep a firm hold on the steering
wheel.
● Do not run the engine indoors.
● Never allow anyone in front of the unit.
2
Safety Rules
& Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
The triangle in text signifies important cautions or warnings which must be followed.
GENERAL WARNINGS
● Know the tractor controls and how to stop quickly.
READ THE TRACTOR OPERATOR’S MANUAL.
● Read this manual and the tractor Operator’s Manual
carefully. Be thoroughly familiar with the controls and
the proper use of the equipment.
● Never allow children to operate the machine. Do not
allow adults to operate it without proper instruction.
● Do not carry passengers.
● Use only attachments or accessories designed for
your machine. See your dealer for a complete list of
recommended attachments or accessories.
● Keep the area of operation clear of all persons, particularly small children, and pets.
● Never direct discharge towards bystanders.
● Make sure all hardware is secure and that dozer
blade is in good operating condition.
● Check to be sure all safety devices and shields are in
place.
● Check that all adjustments are correct before using
this unit.
● Gasoline is highly flammable. Follow all precautions
listed in your tractor’s operator’s manual.
● Always wear eye protection while operating and performing adjustments to protect eyes from debris
thrown by the dozer.
● When cleaning, repairing, or inspecting the unit make
sure all moving parts have stopped. Disconnect and
secure the spark plug wires and remove the key to
prevent accidental starting.
PREPARATION
● Disengage the PTO before making any adjustments.
● Never attempt to make any adjustments while engine
is running.
● Thoroughly inspect the area where the dozer is to be
operated and remove all foreign objects.
● Adjust the skid shoe height to clear gravel or crushed
stone surface. See the Adjustments section for procedure.
DANGER
OPERATING ON SLOPES
CAN BE DANGEROUS
For operation on slopes greater than 15% (8.5°),
weight box, tire chains, and wheel weights are
recommended. NEVER OPERATE ON SLOPES
GREATER THAN 17.6% (10°).
Page 4
3
TRACTOR CONTROLS
Before you begin operating the tractor with the dozer
blade attachment, make certain you have:
• Read and understood the instructions in the
tractor Operator’s Manual.
• Become thoroughly familiar with all of the
tractor controls and their operation, including
how to safely and properly start and stop the
unit.
• Practice driving in an open area—without dozing—to become accustomed to the unit.
Features
& Controls
A. Blade Angle Control Lever
The blade angle release lever controls a spring-loaded
plate which locks the blade in one of three positions.
Use an abrupt pushing/pulling motion to release the
angling mechanism and move the blade left or right.
Push the angling lever forward fully to lock the blade in
the left position. Pull the lever fully back to lock the
blade in the right position. Move the lever slowly past
center to lock in the centered position.
NOTE: It is easier to change the angle of the blade with
the attachment raised.
B. Attachment Lift
NOTE: Models with hydraulic or electric lift should refer
to the tractor operator’s manual for lift control information.
The attachment lift lever raises and lowers the dozer
blade. See the tractor operator’s manual for control
information. See the Adjustments section for proper
attachment lift adjustment.
Please take a moment and
familiarize yourself with the
name, location, and function
of these controls so that you
will better understand the safety and operating instructions
provided in this manual.
Figure 1. Control Locations
A. Blade Angle Control Lever
B. Attachment Lift
CONTROL FUNCTIONS
The information below briefly describes the
function of individual controls. Operating the
tractor and dozer require the combined use of
these controls and additional controls whose
operation is described in the tractor Operator’s
Manual.
A
B
Page 5
4
Checks Before Starting
1. Refer to the Maintenance & Adjustments sections of
this manual and perform any needed service. Also,
refer to the tractor Operator’s Manual and perform
any required service.
2. Remove any objects from the work area which might
interfere with plowing activity.
3. Adjust the skid shoes to desired height. See Skid
Shoe Adjustment.
4. Make sure all hardware is present and secure.
Engine & Ground Speed Selection
Always run the engine at full throttle.
Set tractor speed to obtain the needed power to move
the material. Operate at a safe speed, depending on
conditions, so that you have complete control of the tractor. Rear wheel weights and chains are recommended
for slippery surfaces.
A weight box is recommended for additional traction.
Transporting
For maximum ground clearance, transport the blade to
and from work areas fully raised and angled straight
ahead.
Starting & Stopping
1. Start the tractor engine. Set engine throttle to full.
2. Raise the attachment lift and travel to the work site.
3. Set the angling control to the desired angle.
4. Lower the attachment lift and begin plowing.
5. Raise the plow before backing up.
6. To stop the tractor, set ground speed to neutral and
set the parking brake. Before leaving the seat, stop
the engine, set the parking brake, remove the key,
and wait for all moving parts to stop.
General
Operating Instructions
WARNING
Perform the Safety System Interlock test found in
your tractor Operator’s Manual. If tractor does not
pass the test, do not operate the tractor. See your
authorized dealer. Under no circumstances
should you attempt to defeat the safety system.
Use caution when plowing a snow covered area.
Snow can cover objects such as curbs, drop-offs,
and other obstacles. Be familiar with the area you
are plowing.
To prevent an explosion or fire, never store the
tractor with fuel in the tank inside a building
where an ignition source is present.
DANGER
OPERATING ON SLOPES CAN BE DANGEROUS
Never operate on slopes greater than 17.6% (10°)
which is a rise of 3-1/2 feet (106cm) vertically in
10 feet (607cm) horizontally.
Operate the unit at a slow ground speed when
driving onto slope. Avoid using brakes to control
ground speed.
When operating on slopes that are greater than
15 % (8.5°) but less than 17.6%, use additional
wheel weights or counterweights.
In addition to counterweights, use extra caution
when operating on slopes. Drive UP and DOWN
the slope, never across the face, use caution
when changing directions and DO NOT START
OR STOP ON SLOPE.
For additional traction, tire chains and wheel
weights can be added. Maximum weight added to
tractor should not exceed 35 lbs. per wheel.
IMPORTANT NOTE
To prevent damage to the unit, always
raise the dozer blade BEFORE turning or
backing up.
Page 6
5
General Operating Instructions
Daily Storage
1. Allow tractor engine to cool before storing in any
enclosure.
2. After dozing or plowing jobs are completed, hose or
brush down the blade to remove excess dirt.
3. Lightly oil all pivot points. Coat bare metal surfaces to
prevent corrosion.
IMPORTANT NOTE
Refer to Tractor Operator’s Manual for
important information concerning safely
storing your tractor.
Changing Angle of the Blade:
See Figure 1 for location of Controls.
NOTE: It is easier to change the angle of the blade with
the attachment raised.
1. Raise the attachment lift.
2. Use an abrupt pushing/pulling motion to release the
angling mechanism and move the blade left or right.
Push the angling lever forward fully to lock the blade
in the left position. Pull the lever fully back to lock the
blade in the right position. Move the lever slowly over
center to lock in the centered position.
Dozing Tips
• Determine the best dozing pattern before beginning.
• When land contour permits, it is best to travel in the
longest direction to minimize turning.
• In very deep snow or gravel, it may be necessary to
make the first pass with dozer blade partially raised,
then repeat each pass with the blade lowered to clear
the material left on the surface. Also, it may be necessary to clear less than the full width of the dozer
blade or reduce ground speed.
• When dozing, push the dirt to the desired location,
then drag the blade backwards for final leveling. Pack
down the dirt or gravel by driving the tractor over the
leveled area.
• Use any slight grade to your advantage, doze downhill, and set the blade angle so that the plowed material is moving downhill as it leaves the blade.
Snow Plowing Tips
• Determine the best snow removal pattern before
beginning.
• Plan the pattern so that you avoid pushing snow onto
cleared areas.
• When land contour permits, it is best to travel in the
longest direction to minimize turning.
• In very deep or heavy snow, it may be necessary to
make the first pass with dozer blade partially raised,
then repeat each pass with the blade lowered to clear
the material left on the surface. Also, it may be necessary to clear less than the full width of the dozer
blade or reduce ground speed.
• Snow tends to freeze into solid banks when plowed
off a driveway or other large area. Because of this
you may want to plow snow several feet past the
edge of the drive to allow space for future plowing to
build up.
• If pushing snow past the edges of driveways or sidewalks, be careful not to tear up the grass buried
under snow next to the drive or sidewalk. Lift the
blade several inches off the ground to avoid damaging the grass.
• Spinning tires with tire chains can leave unsightly
marks or permanent damage to asphalt or concrete
driveways or sidewalks. Avoid sudden stops or
starts.
Storage
Off-Season Storage
1. Remove dozer blade and hitch from the tractor.
2. Use water pressure or a brush to thoroughly clean
the dozer blade.
3. Paint, or lightly coat with oil, any area where paint
has been worn or chipped away.
4. Lubricate the dozer blade.
5. Store the dozer blade and hitch in a dry place.
Page 7
6
Maintenance
Schedule For Normal Care
Care Required Schedule
Clean debris from After each use.
dozer blade.
Lubricate dozer blade. Every 10 hours or at
least once a year.
Lubricate Dozer Blade
Lubricate the dozer blade as shown in Figure 2. Where
an oil can is shown, wipe the area clean, apply a few
drops of oil (SAE 30), then wipe up drips or spills.
In general, linkage connections and other parts that have
partial rotational or sliding movement should be lubricated periodically with SAE 30 weight oil. Avoid applying
excessive amounts of oil since this may cause a build-up
of dirt around the lubricated area, making subsequent
lubrication more difficult to accomplish.
WARNING
To avoid serious injury, perform maintenance on
the tractor or dozer blade only when the engine is
stopped, parking brake is set and all moving parts
have stopped. Always remove the ignition key
before beginning maintenance or adjustments to
prevent accidental starting of the engine.
Figure 2. Lubrication Points
Page 8
7
Adjustments
Skid Shoe Adjustment
Slotted holes are provided to permit adjustment of the
shoe assemblies for raising and lowering the blade to
various working heights (see Figure 3).
When cleaning snow from gravel or earth drives or
walks, the shoe assemblies should be lowered fully to
prevent blade contact with gravel or ground. When
cleaning smooth hard surfaces like concrete, the shoe
assemblies are normally placed fully up to allow the
blade to scrape the surface.
To adjust the skid, raise the blade off the ground and
block with a piece of wood. Loosen the bolts (B, Figure
3) and move the skid shoes (A) up or down to desired
height. Tighten the bolts securely.
Figure 3.
A. Skid Shoes
B. Bolts
Spring Tension
See Figure 4. This snow plow/dozer blade is spring
loaded so that when the blade strikes a solid object, the
springs will allow the blade to release as shown, rather
than cause damage. The blade will go back to its original
position after object is cleared.
Figure 4. Dozer Blade “Released”
Figure 5. Tension Springs
A. Eyebolt D. Pivot Frame
B. Nut, 5/16 E. Nut, 5/16
C. Spring
See Figure 5. To adjust spring tension hold rear nut (B)
and loosen front nut (E). Tighten rear nut (B) to increase
spring tension, or loosen to decrease tension.
For initial adjustment, tighten nut (B) on each eyebolt
enough to expose about 3/4" (19mm) of thread. Tighten
front nut (E) against rear nut (B) to lock adjustment in
place.
Page 9
8
Adjustments
Figure 6. Adjusting Lift Rod
A. Front Set Collar
B. Rod Guide
C. Spring
D. Rear Set Collar
E. Spring Clip
Lift Rod Adjustment
In the fully raised position the blade should be 6” off the
ground. In the fully lowered position, the lift rod should
slightly compress the spring creating downward pressure
on the blade.
NOTE: Always adjust the lift height before and after
adjusting the downward pressure.
IMPORTANT NOTE
DO NOT OVER-COMPRESS THE SPRINGS.
In addition to providing downward pressure,
the springs are an elastic medium that
absorbs shocks caused by bumps and
cracks in ground surfaces. Over-compressing the springs defeats this and may cause
damage to the unit.
A
E
B
C
D
Page 10
9
Initial Setup
& Assembly
Ref Qty Description
1 1 ROD, Control Handle, Upper
2 6 NUT, Hex, 5/16-18
3 2 LOCKWASHER, 5/16
4 4 WASHER, 5/16
5 2 CAPSCREW, 5/16-18 x 1-1/4
6 1 ROD, Control Handle, Lower
7 1 CLEVIS
8 1 WASHER, 1/2
9 1 CLIP, Hair Pin
10 3 COTTER PIN
11 1 ROD & PLATE ASMY, Pivot
12 1 DOZER BLADE ASMY, 42”
13 1 SCRAPER BAR
14 6 CARRIAGE BOLT, 3/8-16 x 1
15 10 LOCKWASHER, 3/8
Ref Qty Description
16 6 NUT, Hex, 3/8-16
17 2 SKID SHOE
18 4 WASHER, Plain, 3/8
19 4 CAPSCREW, 3/8-16 x 3/4
20 2 CAPSCREW, 1/2-13 x 1-1/2
21 2 SPACER, 1/2 ID x 3/4 OD x 5/16 LG
22 1 ROD, Latch Stop
23 2 LOCKNUT, 1/2-13
24 1 FRAME ASMY, Dozer
25 2 EYEBOLT
26 2 SPRING, Extension
27 1 CLIP, Hair Pin
28 1 PLATE ASMY, Latch
29 2 SPRING, Torsion
4
6
4
1
3
4
4
11
7
25
26
24
23
21
10
22
20
19
15
18
17
16
14
13
12
15
27
8
9
28
3
5
10
2
2
29
Figure 7. Dozer Components
Page 11
10
Initial Setup & Assembly
2
1
3
5
6
7
9
15
10
11
9
8
8
8
8
4
4
3
13
12
14
18
17
21
16
20
19
16
18
Ref Qty Description
1 2 STOP, Bar
2 2 SCREW, Taptite, 5/16-18 x 1
3 2 SETSCREWS, 5/16 x 1/2
4 2 SET COLLAR
5 1 ROD GUIDE ASSY.
6 1 SPRING
7 1 ROD, Lift, Electric/Hydraulic
8 5 CLIP, Hairpin
9 2 CLEVIS PIN
10 1 PUSH BAR ASSY, Front
11 1 PIVOT PIN
Ref Qty Description
12 1 EYEBOLT, 1/4-20 x 1-1/2
13 1 LOCKNUT, Center, 1/4-20
14 1 BRACKET, Control Rod
15 1 WASHER, 3/8
16 2 WASHER, 5/16
17 2 LOCKNUT, Flange, Whizlock 5/16-18
18 2 CAPSCREW, 5/16-18 x 1-1/2
19 1 BRACKET, Control Rod
20 1 NUT, Hex, Full, 5/16
21 1 LOCKWASHER, 5/16
Figure 8. Push Bar, Hitch, & Lift Rod Components
Page 12
11
Initial Setup & Assembly
INITIAL SETUP & ASSEMBLY
NOTE: Some of the following setup procedures may
already be completed.
Assemble Blade
1. Place the blade on a flat surface.
2. Install the bar stops (A, Figure 9) using the two 5/1618 x 1 taptite screws (B).
3. See Figure 10. Insert threaded end of eyebolt (A)
through lug on blade, and screw on 5/16 nut (B) just
far enough so that it is flush with the end of the eyebolt.
4. Hook the springs (C) into the pivot frame (D). Using a
pliers, stretch the springs to hook the opposite ends
to the eyebolts (A).
5. Tighten the nut (B) on each eyebolt enough to expose
about 3/4" (19 mm) of thread.
6. Holding the first nut (B) with a wrench,add a second
nut (E) to each eyebolt, and tighten securely against
the first nut to act as a jam nut.
Figure 10. Tension Springs
A. Eyebolt D. Pivot Frame
B. Nut, 5/16 E. Nut, 5/16
C. Spring
Figure 9. Bar Stop
A. Bar Stops
B. Taptite Screws, 5/16-18 x 1
Page 13
12
Initial Setup & Assembly
Install Blade
1. Drive the tractor over the push bar until rear of push
bar is under front hitch.
2. Stop engine, remove key and set parking brake.
3. Raise rear of push bar so its arms fit between lugs of
hitch (A, Figure 12) just behind front axle. Use two
clevis pins (B) and spring clips (C) to secure push bar
to hitch.
4. Insert front of push bar (D) into pivot frame on rear of
blade. Then install king pin (E) down through holes in
hitch and pivot frame. Secure king pin with spring clip
(F).
5. Insert prong of rod guide assembly (H) thru hole in
upright of push bar. Secure with spring clip (I).
6. Connect rear of lift rod (J) to tractor lift arm (K) using
spring clip (G).
Figure 12. Push Bar Installation
A. Tractor Hitch G. Spring Clip
B. Clevis Pin H. Rod Guide Assembly
C. Spring Clip I. Spring Clip
D. Push Bar J. Lift Rod
E. King Pin K. Lift Arm
F. Spring Clip
Assemble Lift Rod
1. Assemble lift rod per Figure 11.
Lift Rod Adjustment
Different types of terrain may require an adjustment
to the lift rod assembly. For instructions on how to
make this adjustment refer to the “Lift Rod
Adjustment” procedure in the ADJUSTMENTS section of this manual.
Figure 11. Lift Rod Assembly
A. Set Collars C. Spring
B. Rod Guide D. Lift Rod
A
B
C
D
Page 14
13
Initial Setup & Assembly
Figure 13. Control Rod Support
A. Angling Support D. 5/16 Flatwasher
B. Eyebolt & Locknut E. Flange Locknuts
C. 5/16-18 x 1-1/2 Capscrews
Install Angling Control Rod
NOTE: If installing the dozer attachment on a unit
equipped with a snowcab, replace the control rod support (A, Figure 13) with the hanging support (Ref. No. 19,
Figure 8). Mount the hanging support to the front cab
cross-bar.
1. Set the angling control support (A, Figure 13) against
the right side of the frame. Insert two 5/16-18 x 1-1/2
capscrews (C) through the support (A), and frame.
Space the lower hole away from the frame with a
5/16 washer (D). Secure using flange locknuts (E).
2. Install the eyebolt (B) in the support (A) and secure
with a centerlock nut.
A
B
C
D
E
Figure 14. Assemble Control Rods
A. 1/4-20 Centerlock Nut
B. Eyelet
C. Upper Control Rod
D. 5/16-18 x 1-1/4 Capscrew
E. 5/16 Washers, Lockwashers, & Nuts
F. Lower Control Rod
G. Hair Pin Clip & Washer
A
B
C
D
F
G
E
3. Connect the lower angling rod (F, Figure 14) to the
dozer release lever using a hair pin clip and washer
(G).
4. Insert the upper control rod (C) through the eyelet
(B), and secure the eyelet to the support using a 1/420 centerlock nut (A).
NOTE: It may be necessary to leave the eyebolt nut (A,
Figure 14) loose to prevent binding.
5. Secure the upper rod (C) to the lower rod (F) using
two 5/16-18 x 1-1/4 capscrews (D), washers (qty. 4),
lockwashers, and nuts (E). NOTE: Match offset to
offset so the rods form a straight line.
Page 15
14
Attaching &
Removing
REMOVAL & INSTALLATION
Removing & Attaching Dozer Blade
1. Lower the blade.
2. Remove the hair pin clip and washer (D, Figure 15)
securing the angling control rod to the clevis.
Disconnect the angling control rod.
3. Remove the angling control rod from the
support arm (A).
4. Remove the pivot pin (C) connecting the blade and
pushbar. Remove the blade.
5. Remove pin (E) securing hitch to the tractor.
8. Reinstall all pins for storage.
Install in reverse order of removal.
Figure 15. Dozer Removal
A. Support Arm C. Pivot Pin E. Clevis Pins
B. Hair Pin Clip D. Hair Pin Clip & Washer
D
C
B
A
B
E
C
Page 16
15
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of in/lbs in/lbs in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 19 2.1 30 3.4 41 4.6
8-36 20 2.3 31 3.5 43 4.9
10-24 27 3.1 43 4.9 60 6.8
10-32 31 3.5 49 5.5 68 7.7
1/4-20 66 7.6 8 10.9 12 16.3
1/4-28 76 8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common Hardware Types
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
Hex Head Capscrew
Carriage Bolt
1/4 3/4
1/4 3/4
0
Nut, 1/2”
1/2
1
1/2
Screw, 1/2 x 2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
Body
Diameter
Body
Length
Washer
Lockwasher
Hex Nut
Inside
Diameter
No
Marks
Wrench & Fastener Size Guide
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16
5/16” Bolt or Nut
Wrench—1/2”
3/8
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”
Page 17
16
NOTES
Page 18
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997
www.simplicitymfg.com
© Copyright 2000 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA.
Loading...