Snapper 1695299, 1693706 User Manual

Installation Instructions

54”Turbo Blower

Mfg. No. 1693706, 1695299

For 54” Mower Decks

SAFETY RULES

Read these safety rules, and the safety rules in your tractor Operator’s Manual, and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. THE TRIANGLE IN THE TEXT SIGNIFIES IMPORTANT CAUTIONS OR WARNINGS WHICH MUST BE FOLLOWED.

WARNING

● When blower assembly is removed from the mower deck, the deflector must be properly installed.

● If the mower stalls or the turbo blower chute plugs, disengage the electric clutch (PTO), stop the engine and remove the key. set the parking brake. wait for moving parts to stop. Remove the foreign object or clear the chute with a piece of wood before restarting the engine. Never place hands into blower housing to clear jammed object. Blower may rotate when object is removed.

● For added tractor stability and to prevent tipping or loss of control:

a. Use reduced speed on uneven ground and when

turning corners.

b. Reduce loads on hillsides. It is recommended that

the collection system be kept only half full when negotiating any slopes. Start mowing on slopes when the collection system is empty.

c. Mow up and down the face of slopes; never

across the face of any slope.

● When operating on slopes, use front counterweight. Never operate on slopes greater than 17.6% (10°).

● Know the tractor controls and how to stop quickly. READ THE TRACTOR OPERATOR’S MANUAL.

● Disengage the electric clutch (PTO). Shut off the engine, remove the key, and wait for all moving parts to stop before attaching, adjusting, or disconnecting any part of the collection system.

● Check the collection system to make sure it is bolted tightly to the tractor.

● Look behind to make sure the area is clear before backing up.

● DO NOT turn sharply when travelling alongside a building or any object.

● DO NOT carry passengers on the tractor.

● Read and obey all warning decals.

OPERATION

Operation With Turbo

• Grass should be cut often but not too short. If grass is too long or lush, it may be necessary to keep ground speed to a minimum or to cut only half the width to prevent clogging. If grass is too high, operate with mower in high cutting position. Cut the grass again in lower cutting position, if desired.

• Before mowing, clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades.

• The blower housing should be removed for cleaning. If a large amount of cut grass is spilling out from under the deck, the tube may be plugged or grass bags are full. Shut off tractor, disengage the PTO, remove the key, and allow all moving parts to stop before disconnecting the tube.

• Always operate at full throttle speed.

Operation Without Turbo

• For operation without the turbo, the deflector must be properly installed in the down position and retained by the spring latch.

• To remove turbo, reverse the installation steps.

Recommended Accessories

• Front counterweight is recommended when using rear-mounted grass catcher.

• On slopes over 17.6% (10°), use two rear wheel weights in addition to front counterweight.

Always mow up and down the face of slopes, never across the face. Never mow on slopes greater than 30% (16.7 degrees)

NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position.

WARNING

Read and obey all operation and warning decals.

WARNING

• Do not open cover with engine running.

• Do not operate mower without the complete catcher in place

• When operating on slopes, refer to operator's manual for counterweights.

DANGER

ROTATING CUTTING BLADE

Do not operate mower

without deflector or entire

grass catcher in place.

1704277

1704405

WARNING

• This shield must be in place at all times during operation.

• Mower deflector must be in down position when blower is removed.

1717291

Installation Instructions 54”Turbo Blower

54”Turbo Blower Installation Instructions

Kit Contents:

Ref Part No. Qty. Description

1 1665982 4 RETAINER, Bearing 2 108202 2 BALL BEARING 3 1931333 5 CARRIAGE BOLT, 5/16-18 x 3/4 4 1706631 1 FAN ASSY 5 1927557 8 FLANGE LOCKNUT, 5/16-18 6 1921332 3 CAPSCREW, .312-18X0.750 G5 7 1706634 1 PULLEY 8 960403 1 KEY, Woodruff

9 1960619 1 SET SCREW, Torx, 5/16-18 x 5/16 10 1935255 1 SPEED NUT 11 1919438 1 NYLOCK NUT, 5/16-18 12 1720918 1 COVER 13 1917372 1 NUT, 5/16-18 14 1917356 1 LOCKWASHER, 5/16 15 1713588 1 SPACER 16 1935255 1 PAL NUT, 5/16-18 17 1921959 4 CAPSCREW, 1/4-20 x 5/8 18 1700654 1 BRACKET, Belt Cover 19 1916964 4 LOCKWASHER, 1/4 20 1916622 4 NUT, 1/4-20 21 1721454A 1 COVER, Arbor 22 1921719 1 CAPSCREW, 5/16-18 x 2-1/2 23 1927120 1 CAPSCREW, 7/16-14 x 2-1/4 24 1720737 1 PULLEY & HUB ASMY 25 1720932 1 V-BELT 26 1720749 1 SUPPORT PLATE 27 1720921 3 LOCKING TAB 28 1719590 1 SPRING, Extension 29 1720920 1 PLATE, Deflector Mounting 30 1931320 1 CARRIAGE BOLT, 1/4-20 x 1-1/4 31 1720718 2 PILOT PIN, Tapered Spacer 32 1933896 4 LOCKNUT, 10-24 33 1720951 1 ROD & ANCHOR ASMY, Deflector 34 1960404 4 SCREW, Truss Head, 10-24 x 3/4

Kit Contents:

Ref Part No. Qty. Description

35 1921159 1 CAPSCREW, 1/4-20 x 2-1/4 36 1720978 1 SPACER, 5/8 x 1 37 1704628 2 PIN, Spring 38 1720892 1 HOUSING, with Decal 39 1700259 1 DECAL-Danger 40 1933988 3 PAL NUT, 5/16 41 1672689 1 S-HOOK 42 1927429 3 TAPTITE SCREW, 1/4-20 x 5/8 43 1706630 1 STRAP 44 1960472 6 SCREW, Truss Head, 1/4-20 45 1921969 1 CAPSCREW, 3/8-16 x 1-1/2 46 1924940 4 WASHER, 3/8 47 1708029 1 PULLEY, Idler 48 1916965 2 LOCKWASHER, 3/8 49 1916950 2 NUT, 3/8-16 50 1923701 1 CAPSCREW, 3/8-16 x 2 51 1666114 1 BUSHING 52 1720934 1 LEVER ASMY 53 1922755 1 WASHER, 3/8 54 174896 1 SPRING, Extension 55 1704419 1 BELT STOP 56 1930641 8 LOCKNUT, 1/4-20 57 1921319 1 WASHER, 1/4 58 1921961 1 CAPSCREW, 1/4-20 x 1-1/4 59 1930645 1 NUT, 3/8-16 60 1720721 1 PLATE & BRACKETS ASMY 61 1929000 2 TAPTITE SCREW 62 1668500 1 BRACKET 63 1672735 1 SPRING 64 1917372 6 NUT, 5/16-18 65 1917356 6 LOCKWASHER, 5/16 66 1931333 6 CARRIAGE BOLT, 5/16-18 x 3/4 67 1721023 1 BAFFLE, RH, 26-1/2” 68 1720613 1 BAFFLE, LH, 23-1/2”

+ 5 hidden pages