Snapper 1692210, 1692231, 1692353, 9000100 User Manual
INSTALLATION
INSTRUCTIONS
WARNING
A
Turn off the engine, let the rotor come to a
complete stop and disconnect the spark plug
wire before assembling the vacuum kit or
changing attachments.
A
WARNING
Never remove% adapter from the back of the
machine while the machine is running or the
rotor is turning. The rotor is
es away from the adapter iniet. Serious injury
will result if you put your fingers or foot in the
adapter inlet while the rotor is turning!
INSTALLATION
pinning
just inch-
CHIPPER/SHREDDER VACUUM KIT
Mfg. Nos. 1692210, 1692231, 1692353,900OlOO
Never operate the machine without the cou
pier/hose
assembly or plug connected to the
I
arrows (or seams) running along the top of the coupler with those on the adapter. Push fully in and turn
until it snaps into place.
NOTE:
4. Slip the grip (12) onto the handle (11). Putting some
Insert plug (3) into adapter when vacuum
attachment is not in use. See Removing the
Vacuum Kit on the next page.
soap on the handle will make the grip slide on easi-
er.
1. Remove the rotor housing cover. Retain the screws.
2. Replace the cover with the adapter (1A or 1 B) using
the screws removed in step 1 and washers (15).
3.Twist the coupler (2) onto the end of the hose (4).
Insert the coupler into the adapter hy aligning the
Ref. Qty. Part No. Description
1A
1B
IO
13
14
l Lid color depends on which kit you’ve ordered. Only
one lid is packaged per kit.
1
1021100
1
1713522
2
1
1023100
3
1
1025100 Plug
4
1
1035100
5
1
1027100 Leaf Tray
6
1
1030100 Nozzle
1
7
8
9
11
12
15 3 1919326
1024100 Ring
1
1960294
1
1921319 Washer,
1
6041612
1
1026100
1
1028100
1
5001612
1
1709404*
1
lOlQlOO* Hopper Lid (Gold)
1
1709467*
Adapter
Adapter (European Model)
Coupler
Hose,
10’
x 4” Dia.
Nut, Hex, Flange, l/4-20
l/4
Screw, Phillups Hd.
1/4-20x
Handle
Grip, Handle
Decal, Danger
Hopper Lid (Orange)
Hopper Lid (Red)
I-112
5. Connect the handle to the nozzle (6) using the
screw
(lo),
washers (9) and nut (8).
6. Connect nozzle (6) or leaf tray (5) to the hose,.
7. Securely place hopper lid (14) on hopper.
Figure
1. Kit Parts
-
FORM
PRINTED IN U.S.A.
1709566
12l93SMI
USING THE VACUUM
The vacuum kit lets you take full advantage of the
vacuum created by the four fan blades on the rotor flywheel. Placing the lid on the hopper directs the suction power to the hose inlet at the bottom of the hous-
ing.
Use the vacuum kit to conveniently rake dry leaves
and grass clippings into the leaf tray, where the material is sucked through the vacuum hose, shredded in
the shredding chamber and expelled out the dis-
charge chute. The hopper lid must be in place for the
vacuum to work properly. The clear vacuum hose
allows you to monitor the flow of material. The
urn
kit works best on dry leaves,
The nozzle and handle can be attached to the end of
the hose for, hard to reach places. The strength of the
vacuum can be adjusted by turning the sleeve on the
nozzle end. Open the sleeve fully for minimum suction
power to vacuum leaves over a garden area.
vactt-
VACUUMING TIPS
*
Keep the hose straight for best performance.
*
Rake leaves into the tray at a steady rate so that the
engine or motor runs at an even level. For best
results, do not cram the tray full of leaves.
-
Avoid items, such as twigs, that can get caught in
the hose.
*
If material is wet, allow to dry before vacuuming.
REMOVING THE VACUUM KIT
1.
When not using the vacuum kit, turn off the engine,
let the motor come to a complete, stop and disconnect the spark plug wire.
2. Rotate the coupler/hose assembly until the seams
line up on top, pull until it clicks then unscrew and
remove.
3. Insert the plastic plug (3) into the adapter and twist
until it seats completely
FORM
-
1709566
Loading...