Snapper 1691827 User Manual

INSTALLATION
I
Section A. General
This kit provides an add-on light and required
alternator for compact and large frame snowthrowers with Tecumseh engines. Kit can be installed on snowthrowers that are equipped with cabs (hard or soft). See the appropriate section for installation instructions:
Section C. Section D. Section E. Large-Frame
Section B. Kit Parts
ITEM DESCRIPTION P/N
z-
B. Self-Tapping Screw, l-114”
C. AC Ughtlng Connector D. Spacer’ E. F.
G. H. Plastic Tie’
1.
*5
Alternator
Self-Tapping Screw, :&I@“**
Centertng
Alternator Shaft, 3”” Alternator Shafl,
Headllght Assy.
CIIP
HP Models “7, 6, 10 HP Models
Snowthrower Application Compact No Cab/Soft Cab
Large-Frame
No Cab/Soft Cab Hard Cab
QTY.
-
Tube
3-M”’
1704.346
1704652 1704663
1704647 1704646 1704649
1704641 1704642 1704644 925094 930222
INSTRUCTIONS :
~~,
SNOWTHROWER HEADLIGHT KIT
MFG. NO. 1691827
Sofi
Section C. Compact Snowthrower With
Without Cab.
1. Drill a 13/&Y hole, 5/8” from bottom and centered (approx.
8-i/2”
from either end) on the
crossmember as shown in figure 2.
AD-815
F
:igure 2.
1 3 3 1 1
1 1 1 1 2
1
2. Install light with capsorew, lockwasher, and nut (lockwasher and nut towards rear).
3. Install alternator as provided in the Tecumseh Installation Instructions. Use the appropriate
alternator shaft (F, figure 1) and self-tapping screws (B).
t
4. Install clip and plastic ties as shown in figure 3.
This will prevent wire harness from interfering with recoil starter.
_
‘1990
63
CLIP
-1
Cab/
.
I I
I
Figure 1.
gure 3.
FORM
PRlNTED IN U.S.A.
‘I
1704651-02
10190
Section D. Large Frame Snowthrower With Soft-
Cab/ No Cab.
1. Drill 13/32” hole in right-hand side channel, 3” below auger drive handle and centered (approx.
_~~~
i-3/4”),
as shown in figure 4.
--.- -._~~~~.. ---~ .---
------l
Figure 4.
2. Install light with capscrew, lockwasher, and nut (nut on inside).
3. Install alternator as provided in the Tecumseh Installation Instructions. Make sure alternator is
installed with wire harness plug at the 3:00
position. Use the appropriate alternator shaft (F,
figure 1) and self-tapping screws
(B).
4. Install clip on upright as shown in figure 5 to prevent wire from interfering with recoil starter.
Plastic ties provided with kit will not be used.
5. If soft cab is used, tuck the right-hand side of cab around the light bracket
Section E. Large Frame Snowthrower With Hard Cab.
NOTE
Hard cab should be installed first before
installing light kit.
1. Drill 13/32” hole in the right hand side of thecab frame, approx. 3/4” down and
l-1/2”
from
capscrew, as shown in figure 6.
2. Install light through cab frame with capscrew,
lockwasher, and
3. Install clip on upright
nut (nut on inside).
asshown in figure 5. Plastic
ties provided with the kit will not be used.
:
?.
F
igure
5.
,i,
,.’
c
Loading...