SM Pro Audio Jackaroo Operating Manual

!"#$"%&&

'()%&"*+,&-!"#$"%&&

'./01123

045/6153

7580153967.

6:9;:-.5<23-45=3:2

61128=6153

:6>/2-124123

?582-@28236153

(=/10AB=8:1058-"=;05-?241-+2C0:2

SMPROAUDIO* JACKAROO

SAFETY INSTRUCTIONS

CAUTION:

WARNING:

DETAILED SAFETY INSTRUCTIONS:

Retain Instructions:

Follow Instructions:

Water, Liquid and Moisture:

Ventilation:

Heat:

Power Source:

Grounding and Polarization:

Power-Cord Protection:

Cleaning:

Periods of Inactivity:

Damage Requiring Service:

Servicing:

ALL OTHER SERVICING SHOULD BE REFERRED TO QUALIFIED SERVICE PERSONNEL

To reduce the risk of electrical shock, do not remove the cover or rear
panel of this unit. No user serviceable parts inside. Please refer servicing to
qualified personnel only.

To reduce the risk of fire or electrical shock, do not expose this

appliance to rain or moisture.

All safety and operation instructions of this manual should be read and adhered
to before operation.

Please retain all safety and operating instructions for future reference.

All operation and user instructions should be followed.

The appliance should not be used near water, rain or other liquids. Make sure
that no liquid can leak, spill or otherwise seep into the appliance.

Please place the appliance so no obstacles interfere or impede the flow of air
through the ventilation openings.

The appliance should be situated away from other heat sources such as heaters,
radiators, ovens, or other appliances that produce heat.

Make sure your appliance is set to the correct voltage for the country in which it
will be used.

Precautions should be taken so that the grounding or polarization means of an
appliance is not defeated.

Power supply cords should be routed so that they are not likely to be walked on,
pinched, damaged, worn, or rubbed by any other device or obstacle.

The appliance should be cleaned only with a light soft cloth. Do not use any
damaging or corrosive products on the unit.

The power cord of the appliance should be unplugged from the outlet when left
unused for a long period of time.

The appliance should be serviced by qualified service personnel when:

- The power supply cord or the plug has been damaged; or

- Objects have fallen, or liquid has been spilled into the appliance; or

- The appliance has been exposed to rain; or

- The appliance does not appear to operate normally or exhibits a marked
change in performance; or

- The appliance has been dropped, or the enclosure damaged.

The user should not attempt to service the appliance beyond what is described in
the Operating Instructions.

FOReWORD

INSTALLATION

Mains2voltage

Your SM Pro Audio JACKAROO was carefully packed at the factory and the
packaging is designed to protect the unit from rough handling. Nevertheless,
we recommend that you carefully examine the packaging and its contents for
any signs of physical damage that may have occurred in transit.

If the unit is damaged, please do not return it to us, but notify your dealer and
the shipping company immediately, otherwise claims for damage or replacement
may not be granted. Shipping claims must be made by the consignee.

PLACEMENT

The SM Pro Audio JACKAROO utilizes an electronic circuit. Be sure that there is
enough air space around the unit for cooling. To avoid overheating, please do
not place the unit on high temperature devices such as power amplifiers or near
other units that may have high frequency transmittance, such as wireless devices.

The JACKAROO can be used with voltages ranging from 100V AC to 250V AC.
Please make sure that you have selected the correct voltage range on the back
of the unit and that the required fuse setting is correct as well before switching
the unit ON. Damage occurring as a result of incorrect voltage selection may
not be covered as a warranty repair.

SMPROAUDIO2 JACKAROO

Dear Customer,
Thank you very much for expressing your confidence in SM Pro Audio products

by purchasing this unit. The JACKAROO was designed to be a comprehensive
“workhorse” test device for home, project, and professional studios, live sound
rental companies, repair centers, schools, and fixed installations—in short,

Regards,
SM ProAudio

virtually any and all venues where audio products are used. Drawing on years
of hands-on experience in the audio industry and valuable suggestions from
our customers, our engineers have developed a product that we are certain will
more than meet your expectations. As with all SM Pro Audio equipment, the
JACKAROO was designed to provide you with superb performance, excellent
technical specifications, and uncompromised audio quality at an extremely
affordable price.

connectors

2 x XLR Male
2 x XLR Female
2 x DMX 5-Pin
2 x Speakon
4 x 1/4" TRS
4 x 1/8" (3.5mm) TRS
4 x RCA
2 x 5-Pin DIN/MIDI

2 x RJ11
2 x RJ45
2 x Rotary Signal Attenuators
AC/DC Voltage Generator (5VDC, 12VDC, 9VAC, 17VAC) @ 500milliamp
Banana Plug Continuity Tester
Signal Generator w/ 100Hz / 1kHz / 10kHz Tones
Monitor Speaker (each of the 8 lines being tested can be selected)
Ground Lift Switch
Transformer-Isolation Switch
Left / Right Selection Switch (for splitting stereo to mono signals)

INTRODUCTION

Hardware4DESIGN4

SMPROAUDIO4 JACKAROO

The JACKAROO is a combination cable tester, signal generator, splitter, combiner,
“gender-bender,” and more. Think of it as an audio “Aussie Army Knife”—an
indispensible tool for studios, PA companies, repair shops, fixed installations,

Packaged in a sturdy 2U rack-mount format, the JACKAROO features a wide
assortment of front-panel inputs and outputs, including Neutrik XLR, 1/4" TRS,
1/8" TRS, RCA, 5-Pin MIDI, BNC, RJ11, and RJ45. Any input can feed any
output, making it easy to test cables, split signals among multiple devices,
separate left/right stereo signals, and connect equipment with dissimilar I/O
configurations. Transformer-isolation, on-board continuously-variable passive
attenuators with true switched bypass, and banana plug connections for
continuity testing are also included. You can even monitor the signal with the
included amplifier and speaker on the Jackaroo. (Yes, we really did try to think
of everything!)

touring bands, sound contractors...you get the idea.

As with all SM Pro Audio products, the JACKAROO features a no-compromise
circuit design and only the highest quality hardware components. For enhanced
durability, all inputs and outputs are secured firmly to the exterior chassis.
Great attention has been paid to the overall construction and design to ensure
years of robust performance under a variety of performance conditions.

2 x BNC

05K

JA CK AR OO

ATT

RCA1/8” TR S

WARNIN G: DO NO T ENGAG E CABLE TEST WI TH
P OWER RU NNING THRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TRS

1/4” TRS

Attenu ator

Attenua tor

05K

ATT

RCA1/8” TR S

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TR S

2

Off

5
5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4

6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity te ster

With Bee per & LE D

JACKAROO'Connections

The JACKAROO comprises two sections that can function independently or be
for linked for joint operation. Each section has connectors for signal input (SEND)
and signal output (RECEIVE). Section A contains 10 types of connectors; Section B

SMPROAUDIO' JACKAROO

A B

Connector'types

BNC

1/4" (6.5mm) stereo TRS

1/8" (3.25mm) stereo TRS

RCA

RJ11 (6-pin)

RJ45 (CAT5, CAT5e, CAT6, 8-pin)

XLR

MIDI (5-pin DIN)

SPEAKON (4-pin)

DMX (5-pin)

RCA1/8” TRS XLR

MID I

RJ45RJ11

1/4” TRS

BNC

has four, designed primarily for use with audio signals.

JACKAROO'SIGNAL'ROUTING'AND'LEVEL

SMPROAUDIO' JACKAROO

A B

05K

JA CK AR OO

ATT

RCA1/8” TR S

WARNIN G: DO NO T ENGAG E CABLE TEST WIT H
P OWER RU NNING T HRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TR S

1/4” TRS

Attenu ator Att enuato r

05K

ATT

RCA1/8” TRS

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TR S

2

Off

5

5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4 6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity te ster

With Bee per & LE D

1
2
3

4

5

Signal attenuator
Signal attenuator bypass switch

Section A: GROUND (earth) lift; removes pin 1 from connection
Section B: LINK; When activated, all inputs on section A are copied
on section B, so that stereo signals on A can be split between sections
A and B, or incoming signals can be split among three outputs.

Left / Right selector switch. When splitting a stereo signal into dual
mono signals, use this switch to select if the output side is Left or Right.

Transformer isolation ON/OFF.

Available on pins 2 and 3.

1

2

3

4

5

05K

ATT

Atte nuator

L-RATT PASS

TRGND LIFT

Each of the JACKAROO’s two sections has a panel of controls, the settings of
which determine the level of a signal and how it is routed through the device.
The panels are identical except for the function of switch 3, which in panel A is
used to lift the ground, and in panel B to link the two sections.

JACKAROO'PIN'CONfigurations

Below is a general guide to common pin configurations, which you may find useful
when testing cables.

SMPROAUDIO' JACKAROO

Appl ic ation 1 2 3 Notes

Canford Talkback backbone earth/screen +24V DC audio

D54 screen

no
connection

analogue
multiplex

DMX screen data - data +

this is not an official standard: see esp.
Martin!!!

High End Systems intelligent
fixtures control

ground data - data +

Loudspeakers

Martin intelligent fixtures control
(old)

screen data + data - this is not the same as 3-pin DMX!

Martin intelligent fixtures control
(new)

screen data - data +

Martin have now changed to be pin
compatible with 3-pin DMX

Martin smoke machine control

Microphones (Europe standard) screen signal + signal -

Microphones (US standard)

Microplex common +15 VDC data

XLR 3-Pin

MIDI Connector

Only pins 4 and 5 are normally used.

1+ Positive Carries the positive Channel 1 signal from the amp to the speaker

1- Negitive Carries the negative Channel 1 from the amplifier to the speaker

2+ Positive Carries the second positive (Ch. 2) signal from the amp to the speaker

2- Negative Carries the second negative (Ch. 2) signal from the speaker to the amp

SPEAKON Connector

05K

JA CK AR OO

ATT

RCA1/8î TRS

WARN ING: D O NOT E NGA GE CAB LE TE ST WIT H

POWE R RUN NING T HRU TH E TES T
CABL ES!

RCA1/8î TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4î T RS

1/4î T RS

Atte nuator

Atten uator

05K

ATT

RCA1/8î TRS

RCA1/8î TRSXLR

XLR 1/4î T RS

1/4î T RS

2

Off

5
5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4 6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TR

GND LIFT

L-R

ATT PASS

TRLINK

Banan as:

48V PHA NTOM PO WER

SEN D REC EIVE

Conti nuity te ster

With Be epe r & LED

JACKAROO'functions:'continuity'tester

The JACKAROO features an on-board continuity tester, which allows you to
determine if an electrical path can be established between two points. Using the
included cables, you can easily test a wide variety of equipment, such as lamps,

illuminate if the signal is flowing properly between the two points being tested.

IMPORTANT:

MAKE SURE THE ITEM BEING TESTED IS NOT CONNECTED

TO ANY POWER SOURCE!

JACKAROO'FUNCTIONS:'Test'tone

SMPROAUDIO JACKAROO

05K

JA CK AR OO

ATT

RCA1/8î TRS

WARNING: DO NO T ENGAGE CABLE T EST WITH

POWER RUNN ING THRU THE TEST
CABLES!

RCA1/8î TRS XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4î TRS

1/4î TRS

Attenuato r

Attenuato r

05K

ATT

RCA1/8î TRS

RCA1/8î TRSXLR

XLR 1/4î TRS

1/4î TRS

2

Off

5

5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4

6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banan as:

48V PHA NTOM PO WER

SEN D RE CEIVE

Conti nuit y test er

With B eepe r & LED

Bana nas :

Co ntinuity tes ter

With Beeper & LE

D

Test

Tone

100hz 1k 10k

volume

single wires, PCB circuit boards, and the like. A buzzer will sound and the LED

The tone test generator can be set to 100Hz, 1kHz, or 10kHz. The output level
of the test tone can be adjusted via the screw located to the right of the tone
frequency selector switch.The test tone signal will appear only at the section A
output connectors unless the LINK switch (in the section B control panel) is set
to ON, in which case the tone will appear at both the A and B output connectors.
Note that the signal is carried only by pins 2, 3, and 4 of a connector, as pin 1
is ground.

05K

JA CK AR OO

ATT

RCA1/8” TRS

WARNIN G: DO NO T ENGAG E CABL E TEST WI TH
P OWER R UNNING THRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TRS

1/4” TRS

Attenu ator

Attenu ator

05K

ATT

RCA1/8” TR S

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TRS

2

Off

5

5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4

6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity t ester

With Bee per & LE D

jackaroo-functions:-TESTING--CABLES

IMPORTANT: Before testing any cables, please make sure that no power

is running through them.

When testing a cable to determine the presence of 48V phantom power, do not
engage the CABLE TEST switch. Simply connect the XLR or TRS cable to the

The JACKAROO features a built-in cable tester that performs an automated

test routine. To test a cable, connect both sides of the cable to the appropriate
connectors on the JACKAROO and engage the CABLE TEST switch. The

The JACKAROO will sequentially test each of the connectors’ pins (up to 8),

SMPROAUDIO- JACKAROO

For example, if a properly functioning 3-pin XLR cable is connected to the XLR
SEND and RECEIVE jacks and CABLE TEST is engaged, both upper and lower

LEDs 1 will light up, followed by LED pair 2 and LED pair 3. If the cable was
incorrectly wired, the LEDs would not light, indicating a problem. If the cable had
a short between pins 1 and 2, for example, then LED pairs 1 and 2 would light

WARNING: DO NOT ENGAGE CABLE TEST WITH
POWER RUNNING THRU THE TEST
CABLES!

Cable
Test

1 2 3 4 5 6 7 8

48 V PH ANTOM POWER

and display the status of each pin on the correspondingly-numbered LEDs.

simultaneously, indicating that the signal was shorted across both pins.

TESTING-CABLES-with-phantom-power

JACKAROO; if phantom power is running through the cable, LEDs 2 and 3 will

light simultaneuosly, indicating the presence of phantom power.

05K

JA CK AR OO

ATT

RCA1/8” TR S

WARNIN G: DO NO T ENGAG E CABLE TEST WIT H
P OWER RU NNING T HRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TR S

1/4” TRS

Attenu ator

Attenu ator

05K

ATT

RCA1/8” TRS

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TR S

2

Off

5

5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4

6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity te ster

With Bee per & LE D

05K

JA CK AR OO

ATT

RCA1/8” TR S

WARNIN G: DO NO T ENGAG E CABLE TEST WIT H
P OWER RU NNING T HRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TR S

1/4” TR S

Attenu ator Att enuato r

05K

ATT

RCA1/8” TRS

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TR S

2

Off

5

5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4 6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity te ster

With Bee per & LED

jackaroo-functions:-AC/DC-power-supply

The JACKAROO can supply four different voltages to various devices, such as

effects units, that require external power. Note that the maximum current the

JACKAROO can supply is 500ma (milliamps); connecting devices that exceed

this specification may damage the unit.

Voltages are selected on the JACKAROO front panel. Available voltages are 5VDC,

jackaroo-functions:-Monitor-amp-and-speaker

The JACKAROO has a built in amplifier and speaker that can be used to monitor
audio signals on pins 2 - 8. (Pin 1 cannot be monitored as it is always ground.)
The speaker output volume level can be adjusted via the slotted knob located just

below the monitor selector knob.

SMPROAUDIO- JACKAROO

5V dc

Off

12

V dc

9V ac

17V a c

Voltage selector

Voltage out
Max 500mA

2

Off

5

3

4

6

7

8

Monitor selector

12VDC, 9VAC, and 17VAC. The connector is a 2.1mm DC jack, center positive.

05K

JA CK AR OO

ATT

RCA1/8” TR S

WARNIN G: DO NO T ENGAG E CABLE TEST WIT H
P OWER RU NNING T HRU THE TEST
C ABLES!

RCA1/8” TR S XLR

XLR

Cable
Test

Test
Tone

1 2 3 4 5 6 7 8

MIDI

MIDI

RJ45

RJ45

RJ11

RJ11

1/4” TR S

1/4” TRS

Attenu ator

Attenu ator

05K

ATT

RCA1/8” TRS

RCA1/8” TR SXLR

XLR 1/4” TR S

1/4” TR S

2

Off

5
5V dc

Off

12V dc

9V ac

17V ac

Voltage selector

3

4

6

7

8

Monitor selector

Voltage out
Max 500mA

BNC

BNC

100hz 1k 10k

MONITOR SPEAKER

L-RATT PASS

TRGND LIFT

L-RATT PASS

TRLINK

Banana s:

48V PH ANTO M POWE R

SEN D REC EIVE

Contin uity te ster

With Bee per & LE D

The JACKAROO lets you easily split signals, change connector gender,

perform attentuation, and more.

In this example we’ll take stereo 1/4" TRS cable and split the signal into two mono

RCA outputs.

1. Make sure that the CABLE TEST switch is NOT engaged

2. Connect the 1/4" TRS stereo source signal into the section A 1/4" input (lower left).

3. Connect an RCA cable to the section A RCA output (upper left) and a second

4. Select LEFT using the L-R switch in the section A control panel.

5. Select RIGHT and set LINK to ON in the section B control panel.

The signal will now be split.

If the signal level is too high on one or both sides, switch ATT (attenuation) ON and
use the rotary control(s) to attenuate the signal.

If the signal needs to be transformer isolated, or the ground needs to be lifted to

remove hum and noise, simply engage the GND LFT switch.

By following the above example, you can split, attenuate, and combine signals,

change the gender of connectors, and create a variety of input/output configurations.

SMPROAUDIO- JACKAROO

A B

0

0

5K

5K

ATT

ATT

Atte nua tor

Atte nua tor

L-R

L-R

ATT PASS

ATT PASS

TR

TR

GND LIFT LINK

A

B

JACKAROO-FUNCTIONS:-SPLITTING-signals

Splitting a stereo signal into dual mono signals

cable to the section B RCA output (upper right).

SMPROAUDIO* JACKAROO

JACKROO*REAR*PANEL

The rear panel contains the following connectors:

AC POWER INPUT

110V-240V selector switch

2 AC OUTPUT connectors

2 DC OUTPUT connectors

2 CAT5 LINK connectors

A. Mirrors the front-panel power supply to provide power for external devices,

such as effects pedals, effect units, other circuits, etc. Maximum current is 500ma.

Four voltages are available: 5VDC, 12VDC, 9VAC, and 17VAC.

B. RJ45 connectors for linking together multiple JACKAROOs. If you have several

test rooms, or a studio and a recording room, you are able to connect several

JACKAROOs together so that longer cable runs and different types of gear can
be tested. The RJ45s 8-pins mirror the front-panel section A input signals.

AC Po wer I n

POWE R INPU T

Rj45Rj45

LINK

Made in Chin a

J a c k a r o o

AC 17V 0 .5A AC 9V 0 .5A DC 9V 0 .5A DC 12 V 0.5 A

POW ER SU PPLY

WARNIN G: DO NOT ENGAGE C ABLE TES T WITH
PO WER RUN NING TH ROUGH TH E
TE ST CABLE S!

A

B

SMPROAUDIO* JACKAROO

1*WARRANTY*CARD

2*WARRANTY

3*RETURN*AUTHORIZATION*NUMBER

To be protected by this warranty, the buyer must complete an online warranty
registration within 14 days of the date of purchase on www.smproaudio.com.

1. SM ProAudio warrants the mechanical and electronic components of this
product to be free of defects in material and workmanship for a period of one
years from the original date of purchase, in accordance with the warranty
regulations described below. If any defects occur within the specified warranty
period that are not caused by normal wear or inappropriate use, SM Pro Audio
shall, at its sole discretion, either repair or replace the product.

2. If the warranty claim proves to be justified, the product will be returned freight
prepaid by SM Pro Audio within Australia. Outside of Australia, the product will
be returned at the buyer's expense.

3. Warranty claims other than those indicated above are expressly excluded.

1. To obtain warranty service, the buyer must call SM Pro Audio during normal
business hours BEFORE returning the product (Tel.: [phone]). All
inquiries must be accompanied by a description of the problem. SM Pro Audio
will then issue a return authorization number. Return authorizations may also be
obtained by submitting a request to [e-mail].

2. The product must be returned in its original shipping carton, together with the
return authorization number, to the following address:

SM Pro Audio
Service Department
W25, 26-28 Roberna St
Moorabbin
Melbourne, Victoria
Australia 3189

SMPROAUDIO JACKAROO

4

WARRANTY2

REGULATIONS

52CLAIM2FOR2DAMAGES

62OTHER2WARRANTY2RIGHTS

SM Pro Audio Service Department
W25, 26-28 Roberna St Moorabbin Melbourne, Victoria Australia 3189

ALL RIGHTS RESERVED © 2010 SM Pro Audio

1. Warranty services will be furnished only if the product is accompanied by an original
retail dealer’s invoice. Any product deemed eligible for repair or replacement under the
terms of this warranty will be repaired or replaced within 30 days of receipt of the product
at SM Pro Audio.

2. If the product needs to be modified or adapted in order to comply with applicable
technical or safety standards on a national or local level, in any country which is not the
country for which the product was originally developed and manufactured, this
modification/adaptation shall not be considered a defect in materials or workmanship.

This warranty does not cover any such modification/adaptation, irrespective of whether it
was carried out properly or not. Under the terms of this warranty, SM Pro Audio shall not
be held responsible for any cost resulting from such a modification/adaptation.

3. Free inspections, maintenance/repair work and replacement of parts are expressly
excluded from this warranty, in particular if caused by inappropriate use. Likewise, the
warranty does not cover defects of expendable parts caused by normal wear of the
product. Expendable parts are typically pots, potentiometers, switches, and similar
components.

4. Damages/defects caused by the following conditions are not covered by this warranty:

0LVXVHQHJOHFWRUIDLOXUHWRRSHUDWHWKHXQLWLQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVJLYHQLQ

the user or service manuals

&RQQHFWLRQRURSHUDWLRQRIWKHXQLWLQDQ\ZD\WKDWGRHVQRWFRPSO\ZLWKWKHWHFKQLFDORU

safety regulations applicable in the country where the product is used.

'DPDJHVGHIHFWVWKDWDUHFDXVHGE\DQ\RWKHUFRQGLWLRQEH\RQGWKHFRQWURORI603UR

Audio.

5. Any repair carried out by unauthorized personnel will void the warranty.

6. Products that do not meet the terms of this warranty will be repaired exclusively at the
buyer’s expense. SM Pro Audio will inform the buyer of any such circumstance. If the buyer
fails to submit a written repair order within 4 weeks after notification, SM Pro Audio will

UHWXUQWKHXQLW&2'ZLWKDVHSDUDWHLQYRLFHIRUIUHLJKWDQGSDFNLQJ6XFKFRVWZLOODOVR

be invoiced separately when the buyer has sent in a written repair order.

Failure of SM Pro Audio to provide proper warranty service shall not entitle the buyer to
claim (consequential) damages. In no event shall the liability of SM Pro Audio exceed the
invoiced value of the product.

This warranty does not exclude or limit the buyer’s statutory rights provided by national
law, in particular, any such rights against the seller that arise from a legally effective
purchase contract.

The information contained in this manual is subject to change without notice. No part of
this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording of any kind, for any purpose, without
the express written permission of SM Pro Audio.

.