Thank You
Warranty
Thank you for purchasing PadDock™ 10 from SMK-Link
Electronics. This User’s Guide is designed to help guide
you through setting up your PadDock 10 Stereo Speaker
System for iPad™. The process of setting up your
PadDock 10 is an easy step-by-step process. Should you
need additional help, we have the following resources to
help:
Paddock Specic Website www.pdstand.com
SMK-Link Website www.smklink.com
Toll Free Technical Support 888-696-3500
Free Email Technical Support pcsupport@smkusa.com
Package Contents
User’s
Guide
User’s Guide
USB to Power Cable
PadDock 10
©2010 SMK-Link Electronics. SMK-Link, the SMK-Link Logo and PadDock are
trademarks of SMK-Link Electronics, Inc. Apple and iTunes are registered
trademarks of Apple Inc. iPad is a trademark of Apple Inc. “Made for iPad”
means that an electronic accessory has been designed to connect specically to iPod, iPhone, or iPad, respectively, and has been certied by the
developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory
standards. Please note that the use of this accessory with iPod, iPhone, or
iPad may aect wireless performance. Designed in California by SMK-Link.
Made in Mexico.
USB to mini USB
SMK-Link warranties this product against defects in
materials and workmanship under normal use for a
period of one year from the date of purchase. This
warranty only covers SMK-Link hardware. Please save
your receipt as proof of purchase in the unlikely event
that you need warranty service. A full copy of our
warranty statement can be found at
www.pdstand.com/warranty
SMK-Link Electronics, Inc.
3601-B Calle Tecate (805) 987-6662 Oce
Camarillo, CA 93012 (805) 987-6665 Fax
www.smklink.com
Agency Certifications
USA - FCC CFR 47 Part 15, Subpart B This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation. This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
* Consult the dealer or an experienced radio/TV technician for help.
Operation with non-approved equipment is likely to result in interference to radio and TV
reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Canada - ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation
is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
European RoHS DIR 2002/95/EC
Waste electrical and electronic products must not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority or
Retailer for recycling advice.
User’s
Guide
Setting Up PadDock 10
Before You Begin
The rst time you unpack your PadDock 10, please
remove the protective covering over the bottom anti-skid
pad.
Step 1: Dock iPad
Rotate PadDock 10 until the
speaker is on the left and the
dock connector is down. Align
your iPad against the
speaker with the dock
connectors lining up then
push down rmly.
You can also insert your
iPad with the dock in the
horizontal position, just be
sure that the dock connectors are aligned so you do
not damage your iPad or
PadDock 10.
Note: If your iPad is brand new,
there may be more resistance.
Step 3: Attach To Computer (Optional)
You have the option of attaching the PadDock 10 to your
computer. The mini USB port attaches to the back of the
PadDock 10. The other end of the cable attaches to an
available USB port on your computer.
Step 4: Turning on
Plug your power supply into an available outlet. Switch
the Charge / Sync Switch to Charge mode. You can then
turn your iPad by pressing its power button or home
button.
Charge / Sync Switch
Charge Indicator
Sync Indicator
Volume Knob
Switching Between Charge and Sync Mode
Charge Mode
When the Charge / Sync Switch is in the up position the
system is set into charge and play mode. When set in this
mode, the Charge Indicator should light. If the Charge
Indicator is not lighting, please check the USB to power
cable.
PadDock 10 should be in Charge mode anytime you are
not planning to actively sync with iTunes. The iPad
charges at its highest rate when the speaker is turned
completely o.
Sync Mode
When the Charge / Sync Switch is in the down position
the system is set into Sync mode. When set in this mode,
the Sync Indicator should light. If the Sync Indicator is
not lighting, please check the USB to mini USB cable to
ensure it is attached correctly.
When set to Sync mode, the indicator in the upper right
hand corner of your iPad will indicate Not Charging. The
USB cable provides some power to the iPad to prevent
the battery from draining during syncing. If not switched
back to Charge Mode, once the iPad goes to sleep, it will
charge very slowly at a rate equivalent to plugging
directly into your computer.
Step 2: Attach Power Cable
Take the barrel end of the USB to Power Cable
and plug it into the back of your PadDock 10.
Take the other end and plug it into the
power supply that came with your iPad.
Controlling the PadDock 10
Listen
The volume control knob on the side of PadDock 10
controls the sound level of the speaker system. The
sound can be turned o completely by rotating the
volume knob counterclockwise until it clicks.
The system can simultaneously play music and charge
the iPad. When playing music, the charging rate is
reduced. The speaker connot play music when syncing
with iTunes®.
Please review your iPad documentation for more information about syncing music, videos, pictures, book and apps
to your iPad.
Adjusting the PadDock 10
Rotate
With stops every 90 degrees, PadDock 10 allows you to
choose the best setting for your app or web page. Please
note, care should be taken to avoid tangling the cables.
Tilt
Tilt your iPad by grasping the stand on both side and
tilting to the desired viewing angle.
Loading...