SMK M0001 User Manual
Preliminary
Power Rocking Recliner with Headrest and Lumbar
Power Wall Recliner with Headrest and Lumbar
Operating Instructions Manual
For Product Prexes 1HR & 16H and Handle Values:
RT = Right Toggle (Control Panel)
LT = Left Toggle (Control Panel)
RW = Right Wireless Remote
LW = Left Wireless Remote
DOC014818
07/2019
1
Preliminary
IMPORTANT
Read the safety and other instructions before using your
Power Rocking Recliner with Headrest and Lumbar or
Power Wall Recliner with Headrest and Lumbar furniture.
Keep this manual for future reference.
2
Preliminary
Table of Contents
Important Safety Instructions ................................................................. 4 – 5
Regulatory Compliance Statements ............................................................. 6
Recliner Assembly Instructions................................................................8 – 9
Battery Backup Assembly Instructions .......................................................10
Operating Instructions for Recliners with Standard
Control Panel ....................................................................................... 11 – 13
Operating Instructions for Recliners with
Optional Wireless Remote ...................................................................15 – 20
Troubleshooting ..........................................................................................22
Furniture Placement Guide.........................................................................23
Disclaimer: The information and products featured in this manual may be somewhat
dierent from the product you purchased. La-Z-Boy reserves the right to make
substitutions that are equal in quality and performance.
3
Important: Read these instructions thoroughly before using.
(W63)
(W15)
SUB 1
DANGER – To reduce the risk of electric shock, serious injury or death:
• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this unit if the
(D2a)
• To prevent suocation, keep plastic bags away from children.
(D5)
• Keep cord out of the reach of children and pets that may cause damage.
(D7a)
(D11x)
New variant of D11
• Do not attempt to disassemble or service the product, pump or motor; no serviceable parts are
SUB 8
WARNING – To reduce the risk of burns, re, electric shock, serious
injury or death:
• This product is intended for indoor residential use only.
Preliminary
Important Safety Instructions
When assembling, do not plug in until directed in Operating Instructions.
power control is damaged, wet, in contact with or near spilled water or any liquid. Do not use the
unit if the button activation switch has been exposed to water or any liquid. Do not handle the plug
or remote control with wet hands.
inside. Contact your La-Z-Boy® dealer for service.
• The back of the unit must be lifted for assembly. Please seek assistance if you are unable to lift
(W88)
at least 45 pounds without strain.
(W138)
(W126)
(W145)
(W132)
(W133)
(W131a)
• Keep upholstery away from ames or lit cigarettes. Upholstery may burn rapidly, with toxic gas and
• Unplug the power cord immediately if you detect strange odors or fumes coming from the unit.
(W82)
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
(W140)
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug
• Disconnect the electrical plug from outlet before cleaning, moving, servicing or when not in use for
• Closely supervise children and disabled persons using this product.
(W2)
• This product has many moving parts, serious injury can occur if not used properly. Keep hands,
(W6)
• Do not place power supply underneath the chair.
• Do not place cord under carpet or in a location where it could become worn.
• Do not allow electrical cord to be pinched anywhere.
• Keep the electrical cord away from heat sources.
(W134)
• Do not use this product where the cord may be a trip hazard.
(W129)
• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance
(W17)
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
(W130)
• Never operate the unit with a damaged power supply, electrical cord, plug or connector. Check the
thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery. For your
safety, always use a properly installed smoke detector with working batteries.
and pull it out.
an extended period of time.
ngers and body parts away from the mechanism. To reduce the risk of head entrapment and other
injuries, keep children and pets away from openings and moving parts in and around furniture.
to allow the legrest to fully extend without rubbing or interference.
condition of the power supplies, electrical cords, plugs and connectors often.
Save These Instructions
4
Important: Read these instructions thoroughly before using.
(W29)
(W5)
(W9
(W12)
(W10)
NEW
(W25)
(W26)
(W91)
(W62a)
(W32)
NEW
(W73)
Preliminary
Important Safety Instructions
When assembling, do not plug in until directed in Operating Instructions.
• Do not operate the unit until the back is installed and locked.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.
• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
• Do not stand, sit or place extra weight on the arms, back or open legrest.
• This product may adversely aect medical devices. Do not use near people using or wearing
medical devices.
• Users of medical devices should contact their health care provider before using this product. Do not
use this product if you have poor circulation, are immobile, or cannot sense heat, except as directed
by your health care provider.
• Do not use this product where aerosol (spray) products are being used or where oxygen is being
administered.
• This product is not intended to be used as a bed. Do not sleep in for an extended period.
• Double-insulated products are marked with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED” and may include the symbol M3 (square within a square). Do not attempt to ground
these products, which use two systems of insulation instead of grounding. Double-insulated
products should be serviced only by qualied service personnel, using replacement parts identical
to the original parts.
• Before moving the product, disconnect the electrical plug from the wall outlet and secure the
mechanism to prevent unexpected opening or movement. Never move the product by the
mechanism, legrest, handle, reclining back, or swivel base.
• The Power Rocking Recliner with Headrest and Lumbar and Power Wall Recliner with
Headrest and Lumbar units are intended for a single occupant not exceeding 300 pounds per
seat. Do not operate an individual seat with more than one occupant in or on any part of the
individual seat.
• If you give this product to someone else, include this Operating Instructions manual.
SUB 3
NOTICE – To reduce the risk of product damage:
• To prevent damage to the power supply, do not plug in until instructed.
(N8a)
• Never operate the unit except when it is on its base in the upright position.
(N10)
• Gently press the buttons during operation and avoid hitting the buttons with pointed or hard objects.
(N9)
• After 1 minute of continuous operation, allow the system to rest for 9 minutes.
(N29a)
• Only operate when no foreign object or obstacle will impede, interfere, or otherwise damage the
NEW
unit in any of its positions or while in motion.
Save These Instructions
5
Preliminary
Regulatory Compliance Statements for
Furniture with Wireless Remote
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain must be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par
Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des
autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
6
Preliminary
(Page intentionally left blank)
7
Preliminary
Assembly Instructions
SUB 3
NOTICE – To reduce the risk of product damage:
N18
Do not plug in until instructed.
1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body bracket and
set aside; depending on the product purchased, inside the bag are the power supply, power cord, optional
remote and AAA batteries for the optional remote (Figure 1).
SUB 4
WARNING – To reduce the risk of injury:
W29
W88
Do not operate the unit until the back is installed and locked.
The back of the unit must be lifted for assembly. Please seek assistance if you are unable
to lift at least 45 pounds without strain.
2. Make back electrical connections.
• Lay the back across the arms of the chair. Turn the locking levers, located on the brackets
attached to the back (one on each side), to a 90° angle (Figures 2 and 3).
• Locate and identify the two electrical connections between the back and the body.
- The blue connectors on the left side (sitting) are for the adjustable headrest feature. One
connector routes from bottom of the back panel and the other between the rear seat and tailgate.
- The gray connectors on the right side (sitting) are for the adjustable lumbar feature. One connector routes
from bottom of the back panel and the other between the rear seat and tailgate.
• Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the
connectors.
• Connect the adjustable headrest (Figure 4). Align the pins and sockets in the blue connectors,
push the connectors together and close the locking cover to secure the connection.
• Connect the adjustable lumbar (Figure 4). Align the pins and sockets in the gray connectors, push
the connectors together and close the locking cover to secure the connection.
3. Install the back.
• Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall between
the rear seat and tailgate, and align the brackets on the back with the brackets on the body (Figure 2)
• Lower the back onto the body, making sure the back and body brackets are completely engaged.
- To make sure the back is properly installed with both sets of back and body brackets engaged, stand behind the
chair and twist the back from side to side. If one or both sides move out of position the brackets are not engaged
(Figure 5). Remove the back and repeat the steps above.
- If you are unable to install the back properly, contact your La-Z-Boy® dealer for assistance.
• Lock the brackets by using a screwdriver to push down the locking levers (Figure 3).
4. Locate the motor connector behind the unit. Connect the motor connector to the power supply connector. Align
the connectors, push together until fully seated and close the locking cover to secure the connection (Figure 6).
5. Remove the power supply box from the electrical components bag. Remove the power supply and 120 volt
power cord from the box.
6. Connect the 120 volt power cord to the power supply (Figure 6). Do not plug in until instructed in the operating
instructions.
7. Proceed to the Battery Backup Assembly Instructions.
8. To remove the back, unplug the 120 volt power cord from the electrical outlet, and disconnect the power supply
from the motor connector behind the unit. Reverse the Assembly Instructions steps. When lifting the back
up from the body, to lay across the arms, make sure to do so slowly and carefully to prevent damage to the
electrical connections.
8
Loading...