Smittybilt T0678QC User Manual

Nerf Step (Part# T0678CC) 05-10 Toyota Tacoma Double Cab

Nerf Step (Part# T0678QC) 07-10 Toyota Tacoma Double Cab
Short Bed

Installation Instructions

2” Main tube 5’or 6’ Bed

Bolt Kit:

• 10) 8mm x 1” bolts

• 10) 5/16” washers

• 10) 8mm lock washers

Tools Needed:

• 13mm wrench

1. Remove the bars from their box and
locate the bolt kit. Remove any factory hardware.

See Figure 1

Figure 1

2. Position the step to the driver side of the vehicle. NOTE: The short end of the step board should be located at the front of the
vehicle. Test fit the step board to the factory hole locations. NOTE: The step should line up with the existing factory bolt
locations.

3. Starting with the center bracket, start one 8mm hex bolt, 8mm lock
washer and 8mm
flat washer into the factory bolt location. NOTE: Step board should hang in
location with the bent flange toward the rear of the vehicle. Start the other
8mm nut, 8mm lock washer and 8mm washer on the same bracket. NOTE:
Hand tighten.

See Figure 2

(Figure 2)

4. Start all of the remaining 8mm hex bolts, 8mm nuts, 8mm
lock washers and 8mm flat washers at each bracket. NOTE:
The front bracket only uses one 8mm bolt and washer per side.
Torque each bolt to 15ft/lbs.

See Figure 3

5. Repeat installation procedure on the other side. (Figure 3)
This concludes the step installation.

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 W. Artesia Blvd, Compton, CA 90220

Nerf Step (Part# T0678CC) 05-10 Toyota Tacoma Double Cab

Nerf Step (Part# T0678QC) 07-10 Toyota Tacoma Double Cab
Short Bed

Installation Instructions

2” Main tube 5’or 6’ Bed

Products licensed to N-fab Inc by Fichter Designs is protected by US patent law and International Copy Right law. US Patent #
6588783, # 6874801, # 7416202. Other patents and continuances pending. N-fab products configuration also protected by
International Trade Dress Law. All Design and Patent infringements will be prosecuted to the full extent of the law.

Product cleaning and maintenance instructions

Stainless Steel Finish – Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap, window or

glass cleaner may be used to clean the finish. Dual state powder coat finish – Mild soap, window or glass cleaner may be used to
clean the finish. In order to protect the finish, you may wax your product on a regular basis with pure carnauba automotive wax.
Do not use any types of soap, polish or was that contains abrasive that could damage the finish

WARRANTY

Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs
according to the material and finish of the product purchased. Subject to the duration and conditions of the limited warranty stated
below, Smittybilt warrants to the original retail purchaser that its products are free from defects in material and workmanship. All
other warranties and representations express or implied are hereby disclaimed, including fitness for merchantability and buyer’s
intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to
the selection, suitability and performance of all goods and products selected. This limited warranty does not cover damage or
impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product
modification, improper or inadequate cleaning and/or maintenance. Smittybilt is not responsible for items damaged during
shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited warranty
coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.

Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned
to Smittybilt at customer’s expense. The determination of whether or not a returned part is defective or subject to coverage under
the limited warranties stated herein shall be made at Smittybilt’s sole discretion.

1. Limited Lifetime Warranty on Stainless Steel Products -

Smittybilt stainless steel products carry the foregoing limited repair or replacement warranty against workmanship and defects in the
material so long as the original purchaser retains the original stainless steel parts.

2. Limited Five (5) Year / 50,000 Mile Pro-Rata Warranty (whichever occurs first) on Dual-Stage Powder Coating

Products -

Smittybilt dual-stage powder coated products carry the foregoing limited repair or replacement warranty for a period of (5) years or
50,000 miles (whichever occurs first) from date of purchase against workmanship and defects in the material, provided that any
claim submitted after (2.5) years from date of purchase shall, if accepted, be satisfied by Smittybilt offering customer a credit on the
purchase of a replacement product equal to fifty percent (50%) of customer’s initial purchase price.

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 W. Artesia Blvd, Compton, CA 90220