Installation Instructions
Nerf-Step (Part # N0482CC, N0482QC)
04-09 Nissan Titan Crew Cab 4-Door Short Bed
WWW.SMITTYBILT.COM
NOTE: Carefully read entire instructions thoroughly before attempting to install this part.
It is recommended to have some additional help while installing these bars.
Parts Included Qty Tools Required
8mm x 1” bolts 4 13mm Ratchet with socket or Wrench
8mm nuts 4
5/16” Flat Washer 8
5/16” Lock Washer 8
STEP 1: Start by locating the driver’s side nerf step. To do so, locate the shorter tail bend. The short side goes to
the front of the vehicle.
STEP 2: Locate the factory threaded holes, located under the door on the underside of the body of the vehicle.
NOTE: There will be black plastic caps covering the mounts. Remove all caps and discard.
STEP 3: Hold the step up to the under body of the vehicle and align the factory studs in the body with the upper
mounts in the brackets of the nerf-steps. Install the two 8mm nuts, flat washers, and lock washers-hand
tighten.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 1600 Walnut Parkway, Compton, CA 90220
Picture is for sample use, may not be actual bars
Installation Instructions
Nerf-Step (Part # N0482CC, N0482QC)
04-09 Nissan Titan Crew Cab 4-Door Short Bed
WWW.SMITTYBILT.COM
STEP 4: Next, align the lower mount on the bracket with the lower factory threaded holes in the body of the
vehicle. Install the two 8mm bolts, flat washers and lock washers. Starting with the lower bolts, tighten
all 8mm bolts to 15-20 ft/lbs.
STEP 5: Repeat the process on the passenger side. This concludes the install.
Product cleaning and maintenance instructions
Stainless Steel Finish – Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap, window or glass cleaner may
be used to clean the finish. Dual state powder coat finish – Mild soap, window or glass cleaner may be used to clean the finish. In order to
protect the finish, you may wax your product on a regular basis with pure carnauba automotive wax. Do not use any types of soap, polish or was
that contains abrasive that could damage the finish
Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and
finish of the product purchased. Subject to the duration and conditions of the limited warranty stated below, Smittybilt warrants to the original retail purchaser that
its products are free from defects in material and workmanship. All other warranties and representations express or implied are hereby disclaimed, including fitness
for merchantability and buyer’s intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to
the selection, suitability and performance of all goods and products selected. This limited warranty does not cover damage or impairment in any part due to misuse,
improper installation, accident or contact with on-road or off-road hazards, product modification, improper or inadequate cleaning and/or maintenance. Smittybilt is
not responsible for items damaged during shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited
warranty coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.
Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned to Smittybilt at customer’s
expense. The determination of whether or not a returned part is defective or subject to coverage under the limited warranties stated herein shall be made at
Smittybilt’s sole discretion.
1. Limited Lifetime Warranty on Stainless Steel Products -
Smittybilt stainless steel products carry the foregoing limited repair or replacement warranty against workmanship and defects in the material so long as the original
purchaser retains the original stainless steel parts.
2. Limited Five (5) Year / 50,000 Mile Pro-Rata Warranty (whichever occurs first) on Dual-Stage Powder Coating Products -
Smittybilt dual-stage powder coated products carry the foregoing limited repair or replacement warranty for a period of (5) years or 50,000 miles (whichever occurs
first) from date of purchase against workmanship and defects in the material, provided that any claim submitted after (2.5) years from date of purchase shall, if
accepted, be satisfied by Smittybilt offering customer a credit on the purchase of a replacement product equal to fifty percent (50%) of customer’s initial purchase
price.
Fichter Design's configuration protected by International Trade Dress Law. Fichter Designs licensed to Smittybilt Automotive Products
are Protected by U.S. patent law and International Copy Right Law. US Patent #6588783 and #6874801 other patents and
continuances pending. All Intellectual Property & Patent infringements will be prosecuted to the full extent of the law.
WARRANTY
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 1600 Walnut Parkway, Compton, CA 90220
Loading...