Installation Instructions
N
ote: Please read instruction
s entirely before installing this product.
Outback Wind Breaker
Part # 903xx
WWW.SMITTYBILT.COM
07-11 JK Unlimited (4-Door)
Step 1: Depending on what your vehicle is equipped with remove your hardtop or lower your soft top.
This part can be installed with the soft top lowered back, but if you plan to install this part in
conjunction with a Tonneau cover the soft top and bow assembly will need to be completely
removed. It is also recommended for safety reasons to remove the bow assembly pivot brackets
from the roll bar using a #30 torx bit. (Fig C)
Step 2: Position the Windbreaker between your sport bar with the flap towards the back.
Fasten the windbreaker by running the strap around the sport bar and through the buckle. (Fig A)
Start with the top two center straps. (Fig B) Do not tighten completely at this time.
Slide the strap up through the rear slot
in the buckle then down back through
the front slot in the buckle.
(Fig A) (Fig B)
Step 3: Now secure the two straps on each top corner of the windbreaker. (Fig D)
Step 4: Secure the bottom four straps (2 per side) loosely around the back of the vehicles front seat
risers. (Fig E, F)
Step 5: Position the windbreaker so it’s in the optimal centered location and then proceed to tighten
all of the straps and buckles. Keep in mind; the amount the bottom straps are secured will
effect your seat slider position. Installation is now complete.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Fasten the windbreaker by running the strap
around the sport bar and through the buckle. Start
with the top two center straps. Do not tighten
completely at this time.
Installation Instructions
Outback Wind Breaker
Part # 903xx
WWW.SMITTYBILT.COM
07-11 JK Unlimited (4-Door)
Note: The zipper on the back of the windbreaker underneath the flap is to attach the Smittybilt Tonneau
Cover combination. (Fig G,H)
It is also recommended for safety reasons
to remove the bow assembly pivot brackets
from the roll bar using a #30 torx bit.
(Fig C)
Secure the bottom four straps (2
per side) loosely around the back
of the vehicles front seat risers.
(Fig E) (Fig F)
(Fig D)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
Note:
903xx
Outback Wind Breaker
Part # 903xx
WWW.SMITTYBILT.COM
07-11 JK Unlimited (4-Door)
7614xx
7613xx
(Fig G) (Fig H)
To complete your soft good protection; purchase Smittybilt Tonneau Cover (Part# 7613xx)
and Tonneau Cover Extension (Part# 7614xx). (Fig H)
CARE AND MAINTENANCE
Wash top with warm water and non abrasive soap. Do not wipe the windows with a dry rag or towel, use a
clean water soaked sponge of soft cloth. The zippers should be lubricated to keep them running smoothly.
Limited Warranties
Smittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and finish of the
product purchased. Subject to the duration and conditions of the limited warranty stated below, Smittybilt warrants to the original retail purchaser that its products are free
from defects in material and workmanship. All other warranties and representations express or implied, are hereby disclaimed, including fitness for merchantability and
buyer’s intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to the selection, suitability and
performance of all goods and products selected. This limited warranty does not cover damage or impairment in any part due to misuse, improper installation, accident or
contact with on-road or off-road hazards, product modification, improper or inadequate cleaning and/or maintenance. Smittybilt is not responsible for items damaged during
shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited warranty coverage, the Buyer must provide proof of
purchase. Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned to Smittybilt at customer’s
expense. The determination of whether or not a returned part is defective or subject to coverage under the limited warranties stated herein shall be made at Smittybilt’s
sole discretion.
Smittybilt soft/cut & sew products carry the foregoing limited repair or replacement warranty for a period of (1) one-year against workmanship
and defects in the material from the date of purchase.
To assure product quality, Smittybilt reserves the right to change product design, material, specification and finishes without prior notice to customers. This limited warranty
gives you specific legal rights and you may also have other rights, which may vary from state to state. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply as to you. Also, some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. Smittybilt reserves the right to discontinue product lines and substitute products, or provide other remedies than
those listed in this limited warranty for those discontinued products.
For Technical Support/Warranty Information please call 310-762-9944
Limited One (1) Year Limited Warranty on Soft/Cut & Sew Products -
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Loading...