Installation Instructions
inside of the rear frame rails lining up the nuts in the plate with the holes
XRC Rear Bumper
(Part# 76655)
WWW.SMITTYBILT.COM
07-08 Jeep Wrangler (JK)
NOTE: Carefully read entire instructions before installing this product. It is recommend
having assistance for ease of installation.
Parts Included Qty Parts Included Qty
XRC Rear Bumper 1 ½” Flat Washer (USS) 8
Nut Plate 2 ½” Flat Washer (SAE) 4
½”-13 x 4 ½” Hex Bolt 4 ½” Lock Nut 4
½”-13 x 1 ¼” Hex Bolt 4
Step 1: Remove the factory rear bumper and support brackets from the vehicle.
Step 2: Drill out the four holes in the center of the frame to ½”. ( Fig A)
(Fig A) (Fig B)
Step 3: Insert nut plate into the
in the frame rail. (Fig B)
Step 4: Position the rear bumper up into place, aligning the four holes in the center of the frame with the
holes on the hitch plate portion of the bumper. (Fig D) (This step may require assistance) Attach
using the supplied ½”x 4 ½” bolts with flat washers and lock nuts. Do not completely tighten
at this time.
Drill out the four existing holes in
the center of the frame to ½”.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
bolts with flat washers and lock nuts.
XRC Rear Bumper
(Part# 76655)
WWW.SMITTYBILT.COM
07-08 Jeep Wrangler (JK)
Attach using the supplied ½”x 4 ½”
(Fig C) (Fig D)
Step 5: Install the four ½” x 1 ¼” bolts through the side brackets into the previously installed nut
plate.
Step 6: Make sure bumper is level and the completely tighten all hardware. Torque bolts to 90 ft-lb.
Step 7: Installation is now complete. (Fig E)
Install the four ½” x 1 ¼” bolts
through the side brackets into the
previously installed nut plate.
(Fig E)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
XRC Rear Bumper
(Part# 76655)
WWW.SMITTYBILT.COM
07-08 Jeep Wrangler (JK)
CARE AND MAINTENANCE
To protect your investment it is recommended to regularly wash and wax this part. Do not use any type of
cleaners that contain abrasives that may damage the finish of your part.
LIMITED WARRANTY
Smittybilt (The Company) warrants to the original purchaser of this product that should the product or any part thereof, under
normal use and conditions, be proven defective in material or workmanship within 3 years from the original date of purchase, such
defect(s) will be repaired or replaced (At the Company’s option) without charge for parts or labor.
To obtain repair or replacement within the terms of the warranty, the product is to be delivered with proof of warranty coverage (
e.g. dated bill of sale, receipt), specification of defect, freight pre-paid with Returns Good Authorization Number from Smittybilt to
place of purchase. Items returned to Smittybilt without a Returns Authorization Number will be refused and returned to sender at the
sender’s expense.
This warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged
through altercation, improper installation, mishandling, misuse, neglect accident or acts of nature. THE EXTENT OF THE
COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE
PAID BY THE PURCHASER FOR THIS PRODUCT.
This warranty is in lieu of all expressed warranties and liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE BROUGHTH WITHIN A PERIOD OF 90 DAYS FROM DATE OF ORIGINAL
PURCHASE.IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED,WHATSOEVER. No person
or representative is authorized to assume for the company any liability other than expressed herein in connection with the sale of
this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damage, therefore above limitations may not apply to you. This warranty gives the purchaser specific legal rights. The
purchaser may have additional rights, which vary from state to state.
Limited Five (5) Year / 50,000 Mile Pro-Rata Warranty (whichever occurs first) on Dual-Stage Powder Coating
Products -
Smittybilt dual-stage powder coated products carry the foregoing limited repair or replacement warranty for a period of (5) years or
50,000 miles (whichever occurs first) from date of purchase against workmanship and defects in the material, provided that any
claim submitted after (2.5) years from date of purchase shall, if accepted, be satisfied by Smittybilt offering customer a credit on the
purchase of a replacement product equal to fifty percent (50%) of customer’s initial purchase price
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
XRC Rear Bumper
(Part# 76655)
WWW.SMITTYBILT.COM
07-08 Jeep Wrangler (JK)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
XRC Rear Bumper
(Part# 76655)
WWW.SMITTYBILT.COM
07-08 Jeep Wrangler (JK)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Loading...