Installation Instructions
SRC Classic Sides (Part # 76636)
07-10 Jeep Unlimited (4-Door)
WWW.SMITTYBILT.COM
NOTE: Carefully read entire instructions thoroughly before attempting to install this part.
Parts Included Qty Parts Included Qty
Driver Side Bar 1
Passenger Side Bar 1
Nut-Clip 4
6mm Flat Washer 12
6mm Ny-lock Nut 12
Step 1: Remove oem or aftermarket side rails/steps if equipped. (Fig A)
Step 2: Identify the passenger and driver side. Place the passenger side guard onto the
vehicle by lining up the 6 tabs (2 front , 2 center and 2 back) on the guard with the
already existing holes on the pinch weld area of your vehicle. (On some models you
may need to drill 2 holes) Fig A
Step 3: Identify the two holes (one front and one in the center) on the bottom of the body that the
Nut-clips will be inserted into by where the top brackets of the guard align with. (You may
Need to remove some tape that is applied from the factory that is covering the holes)
Fig B,C,D
10 x 25mm Hex Bolt 4
10mm Flat Washer 4
8mm Flat Washer 2
8 x 25mm Hex Bolt 2
Line up the 6 tabs (2 front, 2 center and 2
back) on the guard with the already
existing holes on the pinch weld area of
your vehicle.
(Fig A) (Fig B)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
You may need to remove some tape that is
applied from the factory that is covering the
holes. (Front passenger side pictured)
Installation Instructions
with.
studs.
SRC Classic Sides (Part # 76636)
07-10 Jeep Unlimited (4-Door)
WWW.SMITTYBILT.COM
Step 4: Loosely attach the guard to the vehicle by inserting the 2-10mm hex bolts into the
nut clips and 6mm lock-nuts onto the bracket studs that go through the pinch weld
area. (Fig D)
Step 5: Insert the 8mm hex bolt with flat washer through the rear bracket into the factory
threaded hole in the bottom of your body tub. (Fig E)
Identify the two
holes (one front
and one in the
center) on the
bottom of the
body that the
Nut-clips will be
inserted into by
where the top
brackets align
Insert clip into body by sliding it in
through the square hole next to it
Loosely
attach the
guard to the
vehicle by
inserting the
10mm hex
bolts into the
nut clips and
6mm locknuts onto the
bracket
(Fig C) (Fig D)
Insert the 8mm hex bolt with flat washer
through the rear bracket into the factory
threaded hole in the bottom of your body
tub.
Now proceed to tighten all of the bolts
and nuts completely. Installation is now
complete. Follow these same steps on
the opposite side.
(Fig E) (Fig F)
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Installation Instructions
SRC Classic Sides (Part # 76636)
07-10 Jeep Unlimited (4-Door)
WWW.SMITTYBILT.COM
Step 6: Now proceed to tighten all of the bolts and nuts completely. Installation is now
complete. Follow these same steps on the opposite side.
CARE AND MAINTENANCE
To protect your investment it is recommended to regularly wash and wax this part. Do not
use any type of cleaners that contain abrasives that may damage the finish of your part.
LIMITED WARRANTY
Smittybilt (The Company) warrants to the original purchaser of this product that should the product or any part thereof, under
normal use and conditions, be proven defective in material or workmanship within 5 years from the original date of purchase, such
defect(s) will be repaired or replaced (At the Company’s option) without charge for parts or labor. To obtain repair or replacement
within the terms of the warranty, the product is to be delivered with proof of warranty coverage ( e.g. dated bill of sale, receipt),
specification of defect, freight pre-paid with Returns Good Authorization Number from Smittybilt to place of purchase. Items
returned to Smittybilt without a Returns Authorization Number will be refused and returned to sender at the sender’s expense. This
warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
altercation, improper installation, mishandling, misuse, neglect accident or acts of nature. THE EXTENT OF THE COMPANY’S
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE
PURCHASER FOR THIS PRODUCT.
This warranty is in lieu of all expressed warranties and liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHTH WITHIN A PERIOD OF 90 DAYS FROM DATE OF
ORIGINAL PURCHASE.IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED,WHATSOEVER. No person or representative is authorized to assume for the company any liability other than expressed
herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damage, therefore above limitations may not apply to you. This warranty gives the purchaser specific legal rights. The
purchaser may have additional rights, which vary from state to state.
For Technical Support/Warranty Information please call 310-762-9944
Smittybilt, 400 West Artesia Blvd, Compton, CA 90220
Loading...