Smittybilt 51034 User Manual

Installation Instructions

Driver Side

Passenger Side

12-1.75mm x 35mm

Tube Spacers

BULL BAR (Part # 51033&51034)

07- 10 SIERRA 1500 / SILVERADO 1500

PARTS LIST:

1 Bull Bar 2 12-1.75mm x 140mm Hex Head Bolts
1 Driver/Left Mounting Bracket 3 12mm Lock Washers
1 Passenger/Right Mounting Bracket 5 12m ID x 29mm OD x 3mm Flat Washers
1 12-1.75mm x 35mm Bolt Plate 3 12mm Hex Nuts

4 8-1.25mm x 30mm Hex Head Bolts
4 8mm Lock Washers
4 8mm ID x 17mm OD x 1.5mm Flat Washers
2 Tube Spacers – 84mm

Mounting Bracket

(1 pc)

(2 pcs)

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 West Artesia Blvd, Compton, CA 90220

Page 1 of 5 12/06/07 (AM)

Mounting Bracket

(1 pc)

Bolt Plate

(1 pc)

Installation Instructions

BULL BAR (Part # 51033&51034)

07- 10 SIERRA 1500 / SILVERADO 1500

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not

required, but strongly recommended. If local/state law requires a license plate, license plate relocation
kit is available.

3. From underside of vehicle, remove the two bolts holding the driver factory tow hook, then remove tow

hook from vehicle. NOTE: This Bull Bar is not compatible with factory tow hooks, so you will not be
reinstalling factory tow hooks back onto vehicle.

4. Loosely attach Mounting Brackets to Bull Bar using the included (4) 8mm x 30mm Hex Head Bolts, (4)

8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this time. NOTE: Refer to
figure above for bracket configuration.

5. With help slide the Bull Bar assembly through tow hook cavities and place Mounting Brackets on the

outer side of frame rails.

6. On the driver side you will be using the front tow hook hole that traverses the frame from side to side

to attach Mounting Bracket to frame rail. Insert (1) Tube Spacers through the front of frame rail and
align it with hole that traverses the frame rail (Figure 2). Secure the assembly with the included (1)
12mm x 140mm Hex Head Bolt, (1) 12mm Lock Washer, (1) 12mm Hex Nut, and (2) 12mm Flat
Washers (Figure 3).

7. On the passenger side use the included (1) 12mm x 35mm Bolt Plate, (1) 12mm Lock Washer, (1)

12mm Hex Nut, and (1) 12mm Flat Washer to attach Mounting Bracket to rear tow hook hole. Repeat
step 6 to attach Mounting Bracket to front tow hook hole (Figure 4).

8. Adjust Bull Bar properly, and then tighten all hardware at this time. NOTE: If you can’t reach the Bull

Bar Bolts (8mm hardware) from behind of bumper and through tow hook cavity, some cutting might be
necessary to the tow hook cavity in order to tighten the Bull Bar Bolts.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a

protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap
may be used also to clean the Bull Bar.

For gloss black finishes: Mild soap may be used to clean the Bull Bar.

For Technical Support/Warranty Information please call 310-762-9944

Smittybilt, 400 West Artesia Blvd, Compton, CA 90220

Page 2 of 5 12/06/07 (AM)