Lift Desk Assembly Instructions
1
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
Form# 179963 www.smithsystem.com 09/2013
You may also place your order online at
Lift Desk Hardware Pack
QTY: 1
Small Modesty Panel
QTY: 1
Large Modesty Panel
QTY: 1
Top Support Brace
QTY: 1
Bottom Support Brace
QTY: 1
Crankshaft Rod
QTY: 1
Lift Desk Leg Set
QTY: 1 Set
Replacement Crank Desk Caster Pack
17590 - Crank Desk Caster Pack 2.6”:
1. (2) 17590L –Crank Desk Caster 2.6”
Locking
2. (2) 17590N – Crank Desk Caster 2.6”
Non-locking
3. (16) M5X10mm Caster Screw
Replacement Fastener Hardware Pack
17708 – Crank Desk Fasteners:
1. (17) M6X1X8mm Machine Screw
2. (9) 70054 #10X3/4” Wood Screw
Replacement Glide Hardware Pack
77875 – 4 Pack M10X5mm Glides
1. (1) 77813 - 3/16” Allen Wrench
2. (4) M10X5mm glides
Replacement Crank Handle Pack
77730 – Crank Desk Handle Replacement:
1. .3125-18 6mm Socket Cap Screw
2. Crank Handle
Hardware and Components
2
Form# 179963 www.smithsystem.com 09/2013
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
3
Step 1: Flip the top over so the laminate is face down.
Step 2: Using the crank shaft rod, manually lower each of the legs to the bottom separately by
inserting the crankshaft rod around the knobs one at a time. Insert the rod on the left and twist
the rod clockwise until bottomed out. Take the rod off of the left knob, insert the rod on the
right knob, and twist the rod counterclockwise until bottomed out.
Step 3: Place the two legs on the top about 2 feet apart. Place the Crank Shaft rod into the
knobs on each of the two legs.
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
Form# 179963 www.smithsystem.com 09/2013
You may also place your order online at
Step 4: Using (4) of the ¼-20 screws, attach the top brace to the legs. Make sure that the large
holes on the brace are facing away from the table top.
4
Step 5: Attach the large panel to the top brace using (3) ¼-20 screws. Make sure that all flanges
are facing towards the front of the table.
(Front) (Rear)
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
Form# 179963 www.smithsystem.com 09/2013
Step 6: Remove the Hex bolt from inside the crank handle rod. Place the Crank Handle on the
Crank Handle Rod. Refasten the Hex bolt into the crank handle rod.
Step 7: Crank the desk all the way extended.
5
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
Form# 179963 www.smithsystem.com 09/2013
You may also place your order online at
Step 8: Using (4) ¼-20 screws, attach the Small Modesty Panel onto the Legs (2 people are
recommended for this step). Be sure that the large modesty panel slides into the small modesty
slots behind the small modesty panel. The side flanges on the small modesty panel should face
towards the back of the table, while the flanges on the top and bottom of the small modesty
panel should face towards the front.
(Front) (Back)
6
Step 9: Crank the desk back down to its lowest setting and attach the bottom bracket to the
feet using (4) ¼-20 screws.
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
Form# 179963 www.smithsystem.com 09/2013
You may also place your order online at
Step 10: Crank the desk up and down a few time to ensure the gears operate correctly.
Step 11: Using (7) wood screws for the 30” and (9) wood screws for the 60”; attach the frame
to the table top. (The extra (2) wood screws on the 60” go on the top support brace).
7
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
Form# 179963 www.smithsystem.com 09/2013
Step 12 (Optional): If desired, attach the (4) casters onto the feet using (16) M5X10mm screws.
The locking casters are most helpful in the front caster position, while the 2 non-locking in the
rear caster positions.
8
Step 12 (Optional): If desired, attach the (4) glides onto the feet.
For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
Form# 179963 www.smithsystem.com 09/2013
You may also place your order online at
Loading...