smirthwaite Easi-Lift Instructions For Use Manual

1/12

Easi-Lift

INSTRUCTIONS FOR USE

Codes 3081-3086

Easi-Lift

1

CONTENTS PAGE

1.0 INTRODUCTION 1

2.0 ILLUSTRATION OF YOUR EASI LIFT CHANGING TABLE 2

3.0 TECHICAL DATA 3

4.0 FOR YOUR SAFETY 4

5.0 SURVEYING AND INSTALLATION 5

6.0 HOW TO USE YOUR EASI LIFT CHANGING TABLE 9

7.0 CARE & MAINTENANCE 11

8.0 GUARANTEE & SERVICE 15

9.0 CONTINUOUS IMPROVEMENT 16

10.0 WARRANTY & AFTERSALE 17

1.0 INTRODUCTION

Thank you for choosing the Smirthwaite Easi Lift changing table.
The Easi Lift is an electrically operated wall mounted changing table designed to fit

in a room where space is at a premium. Its compact design means that it fits well into
a wide range of environments.

IMPORTANT!

These instructions should be read by all therapists and carers using
the equipment and should be retained for future reference. The
product should always be used under adult supervision.

Any incorrect use of the product and failure to follow the instructions
may put the user at risk or impede the function. If you have any
queries using this product or wish for further copies, please do not
hesitate to contact Customer Service department on T: +44 (0)1626
835552

This product has been designed and manufactured specifically and
solely for use by clients with special needs.

Easi-Lift

2

2.0 ILLUSTRATION OF YOUR EASI LIFT CHANGING TABLE

A. Safety side1
B. Bed
C. Wall frame

1

The Easi lift is supplied with either standard safety side or stowaway variant (as displayed).

A B C

Easi-Lift

3

3.0 TECHNICAL DATA

Mild Steel, Powder Coated

Code

3081

3082

3083

3084

3085

3086

Size 1 2 3 4 5 6

User Weight (kg)

150

150

150

150

150

150

Height Range (mm)

450-9502

450-9502

450-9502

450-9502

450-9502

450-9502

Table Dimensions

L Length (mm)

1200

1300

1400

1500

1600

1700

W Width (mm)

550

550

600

600

650

650

M Width (mm)

1010

1010

1060

1060

1110

1110

M Width (mm) 3

875

875

925

925

975

975

Safety Sides

Y Height (mm)

300

300

300

300

300

300

Y Height (mm)3

165

165

165

165

165

165

Wall Frame

A Width (mm)

700

700

700

700

700

700

B Depth (mm)

110

110

110

110

110

110

C Height (mm)

1150

1150

1150

1150

1150

1150

Storage

S Width (mm)

305

305

305

305

305

305

Shipping Weight (kg)

80

82

84

86

88

90

2

Dependant upon installed height

3

When fitted with Stowaway safety rails

Easi-Lift

4

4.0 FOR YOUR SAFETY

STOP!

Please read these instructions CAREFULLY and THOROUGHLY

 DO NOT attempt to install and use this product in a wet room. Please follow installation

instructions as described in Section 5 carefully and thoroughly.

 The user should NOT be left unattended whilst on the changing table. Always ensure a

responsible therapist or carer is in attendance.

 The Easi Lift changing table height should NEVER be adjusted without a carer in

attendance.

 Always ensure the safety side is in the ‘up’ position once a patient is on the table.

 When storing the product vertically (up position), check to ensure that the locking plunger

pin is fully engaged.

 When not in use for periods of time, isolate the electrical supply.

 Always keep this product away from naked flames, cigarettes and sources of heat

including open fireplaces, radiators and heaters.

 Regular maintenance checks and cleaning are essential for the safe use of this

equipment (see care and maintenance section).

 DO NOT fit parts or accessories of other manufacturers to this product unless authorised

to do so in writing by G&S Smirthwaite Ltd. Failure to follow these instructions will not
only invalidate the guarantee but could make the product dangerous to use. G&S
Smirthwaite Ltd will not accept liability for any injury or damage incurred through such
malpractices. Any repairs required must be carried out by G&S Smirthwaite Ltd
authorised personnel.

 If any part is loose, damaged or functioning incorrectly, DO NOT use until rectified.

 The Easi Lift changing table is CE marked. This certifies that it meets all relevant

European safety requirements.

 If you believe the product or any fitted accessory to be faulty at any time, DO NOT USE –

contact Smirthwaite by telephone on [phone]

Easi-Lift

5

5.0 SURVEYING AND INSTALLATION

5.1 SURVEYING PROCEDURES

 Changing benches/tables are normally installed in small rooms with limited

space. In such circumstances it is vitally important to take accurate
measurements of the whole room in question, and make a plan to scale if
possible.

 Ensure that the intended wall for installation is strong enough to support

the weight of the changing bench plus the patient.

 If the wall is of brick or concrete construction, it will be strong enough to support

the equipment without the need of the backing board.

 If the wall is of hollow or soft insulation block construction, then we would always

recommend the backing board is used.

 Check for the position of dado rails, window sills, electrical power points,

switches, etc which may affect the installation.

 Check there is sufficient room around other facilities, e.g. wash basins, toilets,

etc.

 Remember to take into account the safety rail dimensions – check that the bench

would be capable of adjustment over the height range without fouling.

 Check that doors would be clear and that access is still possible
 Inspect the wall to see if padding/spacing is required to correct wall imperfections

 The Easi Lift requires a 220-240V AC 50Hz or 110V AC 60Hz power supply.

 The power connection must be made in an area that is kept free from moisture or

connected via a waterproofed socket with isolation switch.

STOP!

If in any doubt, ALWAYS seek PROFESSIONAL ADVICE

5.2 INSTALLATION TOOLS REQUIRED

 Electric hand drill, with appropriate drill bits for wood and masonry
 Set of spanners
 Tape measure
 Spirit level
 Hammer
 Screw driver
 Personal Protection Equipment (PPE); gloves, safety glasses