smev 7003, 8203, MO9202S, PI7723, PI8543 Installation And Use Manual

FRANÇAIS

NEDERLANDS

DEUTSCH

NORSK

SLOVENSKI

SVENSKA

SUOMI

DANSK

ITALIANO

ENGLISH

ESPAÑOL

INSTALLATION / USAGE / ENTRETIEN - FR

INSTALLATIE / GEBRUIK / ONDERHOUD - NL

INSTALLATION / GEBRAUCH / WARTUNG - DE

ASENNUS / KÄYTTÖ / HUOLTO - FI

INSTALLATION / ANVÄNDNING / UNDERHÅLL - SE

INSTALLASJON / BRUK / VEDLIKEHOLD - NO

INSTALACIJA / UPOR ABA / VZDR ŽEVANJE - SI

INSTALLATION / USE / MAINTENANCE - GB

INSTALLA ZIONE / USO / MANUTENZIONE - IT

INSTALLATION / BRUG / VEDLIGEHOLDELSE - DK

INSTALACIÓN / USO / MANUTENCIÓN - ES

INSTALAÇÃO / UTILIZAÇÃO / MANUTENÇÃO - PT

PORTUGUÊS

7003 - 7023 - 7103 - 7123 - 8103 VD - 8103 VDM - 8123 VD - 8123 VDM

8203 - 8203 M - 8223 - 8223 M - MO8302 - MO8303 - MO8322 - MO8323

MO8342 - MO8362 - MO8801D - MO8801S - MO8821D - MO8821S

MO9122 - MO9202D - MO9202S - MO9222D - MO9222S - PI7203 - PI7223 - PI7703

PI7723 - PI8002 - PI8003 - PI8022 - PI8023 - PI8042 - PI8043 - PI8062 - PI8063

PI8403 - PI8423 - PI8443 - PI8463 - PI8502 - PI8503 - PI8522 - PI8523 - PI8542

PI8543 - PI8562 - PI8563 - PI8621A - PI8621R - PI8621S - PI8802D - PI8802S

PI8822D - PI8822S - PI8842D - PI8842S - PI8862D - PI8862S - PI9003 - PI9023

12

ENGLISH

SYMBOLS

WARNINGS AND SAFETY SYMBOLS
The safety symbols utilised identify possible hazards to users.
Always respect all safety warnings identified with these symbols:

INDEX

INSTALLATION 13
SAFETY WARNINGS 13

CABINET APERTURE 13
CONNECTING TO GAS SUPPLY 14
WIRING- CONNECTING TO ELECTRICITY SUPPLY 15
FIXTURE 15

USE 16

WARNINGS 16

CONTROLS 16
BURNERS: 17
HOB: 18
SELECTING BURNER 18
ELECTRONIC IGNITION HOB (DEPENDING ON MODEL) 18
MANUAL IGNITION HOB 18
HOB FLAME REGULATION 18
VISUAL FLAME CONTROL 19
GAS CYLINDERS / BOTTLES 1

9

MAINTENANCE 20

CLEANING 20

INJECTORS 20
SMEV ACCESSORIES 20
TEST PRESSURE POINT10

FIGURES AND TECHNICAL DRAWINGS 122-135

WARNING
Hazard of injury or death.

CAUTION
To prevent possible injury
and / or damage

INSTALL ATIONUS E

MAINTENA NC E

13

ENGLISH

SAFETY WARNINGS

THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE
REGULATIONS IN FORCE AND ONLY USED IN AN ADEQUATELY VENTILATED
AREA. ALWAYS READ THE INSTRUCTIONS PROVIDED THOROUGHLY BEFORE
INSTALLING AND USING THIS APPLIANCE.
THIS APPLIANCE MUST BE INSTALLED BY SPECIALISED GAS SERVICE ENGINEERS.

THIS APPLIANCE IS DESIGNED AND MANUFACTURED FOR COOKING FOOD
ONLY. ANY OTHER USE IS CONSIDERED IMPROPER AND INCORRECT CREATING
HAZARDOUS CONDITIONS. THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR DAMAGE TO THINGS OR INJURIES TO PERSONS CAUSED BY INCORRECT
INSTALLATION AND / OR INCORRECT AND IMPROPER USE.

BEFORE INSTALLING CHECK THAT THE LOCAL GAS AVAILABLE (GAS TYPE AND
PRESSURE) AND THE APPLIANCE REGULATORS ARE COMPATIBLE WITH THE
APPLIANCE ITSELF.

GAS REGULATING SPECIFICATIONS FOR THIS APPLIANCE ARE PROVIDED ON THE
LABEL AFFIXED TO THE APPLIANCE (OR ON THE SERIAL PLATE).

THIS APPLIANCE IS NOT CONNECTED TO A FUME EXTRACTION FLUE FOR
EXTRACTING PRODUCTS OF COMBUSTION THEREFORE IT MUST BE INSTALLED
AND CONNECTED (FITTED) CONFORMING TO INSTALLATION REGULATIONS
IN FORCE FOR APPLIANCES OF THIS TYPE. IT IS OF UTMOST IMPORTANCE TO
RESPECT LEGISLATION REGARDING VENTILATION.

THE APPLIANCE MUST FITTED AT AN APPROPRIATE AND SAFE DISTANCE FROM
FLAMMABLE MATERIALS.

CABINET APERTURE

This hob has a class 3 grading: BUILT-IN APPLIANCE FOR KITCHENS OR WORKTOPS

MINIMUM ALLOWABLE DISTANCES FROM WALLS (FIG. 1 - PG. 122):

A / B FROM THE OUTER EDGE OF THE BURNER HEAD NEAREST ONE OF THE SIDE WALLS AND / OR

REAR WALL:
135 mm

C THE DISTANCE BETWEEN THE TOP OF THE BURNER AND THE BOTTOM OF THE UNITS AND /
OR SHELVES FITTED ABOVE THE HOB:
500 mm

D THE DISTANCE BETWEEN THE BOTTOM OF THE BURNER AND THE UNDERSIDE:
30 mm

SIZE OF CABINET APERTURE

Cut-out a hole in the cabinet as illustrated in FIG. 2 - PG. 123 depending on model to install.
The cabinet must be appropriately constructed and aligned horizontally with the worktop and with the unit.
The cabinet aperture must be perfectly squared and aligned.
If there are apertures for cabinet ventilation, prevent flammable materials from entering these.

Models PI8621A, PI8621S and PI8621R are modular.
It is possible to connect from 1 to 5 appliances in series.
ALWAYS RESPECT THE DISTANCE BETWEEN ONE CABINET APERTURE AND ANOTHER (FIG. 2 – PG. 130).

INSTALL ATION

US E

MAINTENA NC E

14

ENGLISH

CATEGORY AND COUNTRY OF DESTINATION

I3B/P(30)

AT BE DK FI DE GB NL NO SE CH SI

I3+ (28-30/37)

BE FR IE IT ES CH GB PT SI

GAS PRESSURE

30 mbar Butane (G30)

30 mbar Propane (G31)

28-30 mbar Butane (G30)

37 mbar Propane (G31)

This appliance is designed for running off the following types of gas at the corresponding operating pressures. The gas
category (or categories) of the appliance is given on the specifications label affixed to the appliance.

CONNECTING TO GAS SUPPLY

CHECK THESE SPECIFICATIONS BEFORE CONNECTING THE APPLIANCE TO THE
GAS CYLINDER /BOTTLE. THE PRESSURE REGULATORS CONNECTED BETWEEN
THE GAS CYLINDER AND APPLIANCE MUST CONFORM WITH THE CATEGORIES
GIVEN IN THE TABLE BELOW.

MODEL TOTAL NOMINAL THERMAL

CAPACITY

AIR VOLUME REQUIRED FOR

COMBUSTION

MO8801D - MO8801S - MO8821D

MO8821S - PI8621A

PI8621S

PI8621R

MO8302 - MO8322 - MO8342

MO8362 - MO9202D - MO9202S

MO9222D - MO9222S
PI8002 - PI8022 - PI8042 - PI8062
PI8502 - PI8522 - PI8542 - PI8562

PI8802D - PI8802S - PI8822D - PI8822S
PI8842D - PI8842S - PI8862D - PI8862S

MO9122

7003 - 7023 - 7103 - 7123

8103 VD - 8103 VDM

8123 VD - 8123 VDM

8203 - 8203 M - 8223 - 8223 M

MO8303 - MO8323 - PI9003 - PI9023

PI7203 - PI7223 - PI7703 - PI7723
PI8003 - PI8023 - PI8043 - PI8063
PI8403 - PI8423 - PI8443 - PI8463
PI8503 - PI8523 - PI8543 - PI8563

kW - gr/h m3/h

1,0 - 73

1,8 - 131
2,2 - 160

2,8 - 204

3,2 - 233

3,6 - 262

3,8 - 277

4,6 - 335

2,0

3,6

4,4

5,6

6,4

7,2

7,6

9,2

INSTALL ATIONUS E

MAINTENA NC E

15

ENGLISH

FIXTURE

THIS APPLIANCE MUST BE FITTED AND SECURED TO THE CABINET UTILISING THE FIXTURE SCREWS AS
ILLUSTRATED IN FIG. 3 - PG.131.

The gas supply pipe connected to the appliance must be a rigid metal pipe with sealed fittings. It is possible to fit
a flexible hose, however, in this case the following conditions must be respected:

a) The hose can be accessed easily for inspection;
b) The hose must be protected against coming into contact with parts which heat up (for example parts
underneath the burners);
c) The hose must be protected against being damaged (twisting, pulling, trapping,….);
d) The hose must be protected against being trapped by moving parts (e.g. drawers);
e) The hose must not have a length over 1.5 m;
f) The hose must be replaced before its expiry date;
For models PI8621A, PI8621S, PI8621R seal the appliance gas pipe utilising the sealed tube with pre-mounted
gas fitting provided. Once the appliance has been connected to the gas supply check for gas leaks utilising a non­corrosive fluid. Do not use a water and soap solution. NEVER USE A FLAME TO TEST FOR GAS LEAKS

Models PI8621A, PI8621S and PI8621R are modular. It is possible to connect from 1 to 5 appliances in series.
Disconnect and remove the sealed tube mounted to the gas pipe on the installed appliance and connect it to the
gas pipe on the appliance to install. Connect the appliances together by connecting the gas pipes in series utilising
the fitting.

CONNECTING TO ELECTRICITY SUPPLY

THIS APPLIANCE MUST BE CONNECTED TO A 12 VDC POWER PACK ONLY. THE
CIRCUIT MUST BE FITTED WITH A SAFETY FUSE NOT HIGHER THAN 3 AMP.

WHEN WIRING RESPECT CORRECT POLARITY!

IT IS OF UTMOST IMPORTANCE NEVER TO CONNECT THIS APPLIANCE TO MAINS
VOLTAGE (230 V) WHICH IRREVERSIBLY DAMAGES APPLIANCE COMPONENTS AND
CREATES A HAZARD TO THE USER.

To connect the appliance use a 1.5 mm2 double red and black wire and wire to the terminal junction box located at the
rear of the appliance. The red terminal is the positive pole and the black terminal is the negative pole.

This chapter refers only to models with the wording 12 VDC on the appliance specifications label affixed to the
appliance.

WHEN INSTALLING AND CONNECTING THE APPLIANCE TO THE GAS SUPPLY,
ENSURE THAT THE GAS SUPPLY HOSE IS NOT TWISTED, STRETCHED OR
SUBJECTED TO ANY FORM OF STRAIN WHICH COULD CREATE A HAZARD.

INSTALL ATION

US E

MAINTENA NC E

16

ENGLISH

WARNINGS

THIS APPLIANCE MUST ONLY BE USED BY RESPONSIBLE ADULTS. DURING USE
AND IMMEDIATELY AFTER USE THE BURNER AND OTHER ACCESSIBLE PARTS MAY
BE HOT; DO NOT TOUCH THESE PARTS AND ALWAYS KEEP CHILDREN AT A SAFE
DISTANCE. AFTER USING THE APPLIANCE ENSURE THE KNOB/KNOBS ARE OFF.
AFTER USE ALWAYS SHUT OFF THE GAS SUPPLY AT THE MAIN GAS TAP.

THE USE OF GAS APPLIANCES GENERATES HEAT AND MOISTURE IN THE
IMMEDIATE AREA. ALWAYS ENSURE A GOOD VENTILATION IN THE COOKING
AREA: KEEP ALL AIR VENTS OPEN FOR NATURAL VENTILATION OR INSTALL AN
EXTRACTOR FAN (COOKERHOOD).

DUE TO INTENSIVE USE OF THE APPLIANCE IT MAY BE NECESSARY TO INCREASE
VENTILATION SUCH AS OPENING A WINDOW OR INCREASING COOKERHOOD
(EXTRACTOR FAN) SPEED.

FOR MODELS MO8800 THE DRAINER MUST BE REMOVED WHEN UTILISING THE
HOB BURNER/S.

CAUTION: THIS WARNING IS AFFIXED IN VISIBLE LOCATION ON THE HOB
GLASS LID. GLASS HOB LIDS MAY SHATTER WHEN HEATED. ALWAYS RAISE
THE LID BEFORE IGNITING A BURNER/S (HOB, OVEN AND GRILL) AND TURN OFF
ALL BURNERS (HOB, OVEN AND GRILL) AND LET THEM COOL DOWN BEFORE
LOWERING THE HOB GLASS LID.

CAUTION: THIS WARNING REFERS TO MODELS WITH INCORPORATED SINK
UNIT AND HOB AND WITH GLASS LID DIVIDED BETWEEN SINK AND HOB.
THIS WARNING IS AFFIXED IN A VISIBLE POSITION ON THE SINK UNIT GLASS
LID. WHEN USING THE HOB WITH THE GLASS LID ON THE SINK UNIT CLOSED,
ALWAYS KEEP PANS ON HOB AT A DISTANCE OF 10 MM MINIMUM FROM SINK
UNIT GLASS LID.

The following symbols indicate the burner corresponding to the control knob.
NOTE: different models may have different knobs and different symbols.

THIS SYMBOL IS PLACED NEXT TO THE HOB BURNER KNOBS.
FULL DOT REFERS TO THE CORRESPONDING HOB BURNER.

GAS OFF

HIGH FLAME

LOW FLAME

The following symbols indicate the burner regulation corresponding to the knob position.
NOTE: different models may have different knobs and different symbols.

OTHER SYMBOLS

PUSHBUTTON ELECTRONIC IGNITION

CONTROLS

INSTALL ATIONUS E

MAINTENA NC E

17

ENGLISH

BURNERS

Technical specifications for burners referring to appliance model:

7003 2 1 73 1 1,8 131
7023 2 1 73 1 1,8 131
7103 2 1 73 1 1,8 131
7123 2 1 73 1 1,8 131
8103 VD 2 1 73 1 1,8 131
8103 VDM 2 1 73 1 1,8 131
8123 VD 2 1 73 1 1,8 131
8123 VDM 2 1 73 1 1,8 131
8203 2 1 73 1 1,8 131
8203 M 2 1 73 1 1,8 131
8223 2 1 73 1 1,8 131
8223 M 2 1 73 1 1,8 131
MO8302 1 1 73 1 1,8 131
MO8303 2 1 73 1 1,8 131
MO8322 1 1 73 1 1,8 131
MO8323 2 1 73 1 1,8 131
MO8342 1 1 73 1 1,8 131
MO8362 1 1 73 1 1,8 131
MO8801D 1 1 73
MO8801S 1 1 73
MO8821D 1 1 73
MO8821S 1 1 73
MO9122 2 1,8 131
MO9202D 1 1 73 1 1,8 131
MO9202S 1 1 73 1 1,8 131
MO9222D 1 1 73 1 1,8 131
MO9222S 1 1 73 1 1,8 131
PI7203 1 1 73 2 1,8 131
PI7223 1 1 73 2 1,8 131
PI7703 1 1 73 2 1,8 131
PI7723 1 1 73 2 1,8 131
PI8002 1 1 73 1 1,8 131
PI8003 1 1 73 2 1,8 131
PI8022 1 1 73 1 1,8 131
PI8023 1 1 73 2 1,8 131
PI8042 1 1 73 1 1,8 131
PI8043 1 1 73 2 1,8 131
PI8062 1 1 73 1 1,8 131
PI8063 1 1 73 2 1,8 131
PI8403 1 1 73 2 1,8 131
PI8423 1 1 73 2 1,8 131
PI8443 1 1 73 2 1,8 131
PI8463 1 1 73 2 1,8 131
PI8502 1 1 73 1 1,8 131
PI8503 1 1 73 2 1,8 131
PI8522 1 1 73 1 1,8 131
PI8523 1 1 73 2 1,8 131
PI8542 1 1 73 1 1,8 131
PI8543 1 1 73 2 1,8 131
PI8562 1 1 73 1 1,8 131
PI8563 1 1 73 2 1,8 131
PI8621A 1 1 73
PI8621R 1 2,2 160
PI8621S 1 1,8 131
PI8802D 1 1 73 1 2,2 160
PI8802S 1 1 73 1 2,2 160
PI8822D 1 1 73 1 2,2 160
PI8822S 1 1 73 1 2,2 160
PI8842D 1 1 73 1 2,2 160
PI8842S 1 1 73 1 2,2 160
PI8862D 1 1 73 1 2,2 160
PI8862S 1 1 73 1 2,2 160
PI9003 2 1 73 1 1,8 131
PI9023 2 1 73 1 1,8 131

THERMAL CAPACITY BURNERS MODEL

SEMI-RAPID

Ø 62 mm

AUXILIARY

Ø 47 mm

RAPID

Ø 77 mm

nr. Kw gr/h nr. Kw gr/h nr. Kw gr/h

INSTALL ATION

US E

MAINTENA NC E

AUXILIARY

Ø 47 mm

from 6 to 16 cm

SEMI-RAPID

Ø 62 mm

from 16 to 22 cm

RAPID

Ø 77 mm

from 16 to 22 cm

BURNER PAN DIAMETER

18

ENGLISH

To ignite burner, gently push-in and turn the control knob to position HIGH FLAME and maintaining the knob pushed
at the same time press the electronic ignition pushbutton. Once the burner is alight maintain the knob in this position
for a few seconds to the ensure the flame remains alight.

-MANUAL IGNITION HOB

THE FLAME MUST NEVER EXTEND BEYOND THE EDGE OF THE PAN. CENTRE THE
PAN OVER THE BURNER ENSURING STABILITY ON THE PAN SUPPORT.

- SELECTING BURNER

- ELECTRONIC IGNITION HOB (DEPENDING ON MODEL)

HOB

Manual ignition when the appliance is not fitted with the electronic ignition feature or in the event of failure in the
electronic ignition.

MAKE SURE THERE ARE NO PANS OR OTHER ANY OBJECTS ON THE BURNERS
WHEN IGNITING.

IF THE BRUNER DOES NOT IGNITE IMMEDIATELY REPEAT IGNITION AFTER
HAVING FOLLOWED EACH STEP BELOW:

• TURN THE KNOB TO “SMALL FLAME”

• PROCEED WITH MANUAL IGNITION

• CHECK THERE IS SUFFICIENT GAS IN THE GAS BOTTLE.

IF THE APPLIANCE STILL DOES NOT IGNITE SHUT OFF THE GAS SUPPLY AT THE
MAIN GAS TAP AND CONTACT YOUR LOCAL DEALER.

MAKE SURE THERE ARE NO PANS OR OTHER ANY OBJECTS ON THE BURNERS
WHEN IGNITING.

To ignite burner, gently push-in and turn the control knob to position HIGH FLAME and maintaining the knob pushed at
the same time light the burner with a match or gas lighter. Once the burner is alight maintain the knob in this position
for a few seconds to ensure the flame remains alight.

IF THE BURNER DOES NOT IGNITE IMMEDIATELY CHECK THERE IS SUFFICIENT
GAS IN THE GAS BOTTLE.

IF THE APPLIANCE STILL DOES NOT IGNITE SHUT OFF THE GAS SUPPLY AT THE
MAIN GAS TAP AND CONTACT YOUR LOCAL DEALER.

- HOB FLAME REGULATION

To regulate flame turn the knob to the desired cooking flame.