Smeg WM40T-1 User Manual

THE CONTENTS SECTION 1:BEFORE USING

• Safety warnings

• Recommendations

SECTION 2:INSTALLATION

• Removal of transportation screws

• Adjustment of feet

• Electrical connection

• Water supply connection

• Water drain connection

SECTION 3:TECHNICAL SPECIFICATIONS SECTION 4:CONTROL PANEL

• Start/Pause button

• Function indicator lights

• Function buttons

• Spin speed selector

• Program knob

SECTION 5:WASHING YOUR LAUNDRY

• Before washing

• Running the machine

SECTION 6:MAINTENANCE AND CLEANING

• Water inlet filters

• Pump filter

• Detergent drawer

• Siphon plug

• The cabinet

• The drum

• Remove of your machine from lime

SECTION 7: PRACTICAL INFORMATION SECTION 8:AVOIDING MINOR FAULTS SECTION 9:AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10:INTERNATIONAL WASHING SIGNS

SECTION 1:BEFORE USING

SAFETY WARNINGS

• Do not use a multiple socket or extension cord.

• Do not insert a plug with damaged or broken cord into the socket.

• If the cord is damaged it should be replaced by the manufacturer or

appointed service agent in order to avoid a hazard.

• Never remove the plug from the socket by pulling from the cord section. Remove the plug by holding.

• Do not plug the power supply with wet hands.

• Never touch the machine with wet hands or feet.

• Never open the detergent drawer while the device is running.

• Never force to open the door of the machine while the machine is

running.

• Since the machine can reach high temperatures while running, do not touch the drain hose and water during draining.

• In case of any failure, first unplug the device and close the water tap. Do not attempt to repair.Please apply to the nearest authorized service station.

• Do not forget that the packing material of your machine may be hazardous for children.

• Do not let your children play with the washing machine.

• Keep your pet away from your machine.

• Your machine should only be used by adults within the information

written in this manual.

• Your machine is designed for use in house environment. Warranty will be invalid if you use it for commercial purposes.

• The appliance should not be put on a carpet which can block the air ventilation on the bottom side.

RECOMMENDATIONS

• The detergent or softener in contact with air for a long time will dry and stick to your detergent drawer.To avoid this put your detergent and softener into the detergent drawer just before washing.

• It is recommended that you use pre-washing program for only very dirty clothes.

• Please do not exceed the maximum loading capacity.

• If you will not use your machine for a long time, unplug your machine, close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour.

• As a result of the quality control procedures, a certain amount of water may remain in your machine. This is not harmful for your machine.

SECTION 2: INSTALLATION

You must pay attention to the following issues before using your washing machine.

REMOVAL OF TRANSPORTATION SCREWS

• Transportation screws, which are located at the back side of the machine, must be removed before running the machine.

• Loosen the screws by rotating counterclockwise by a suitable wrench. (DIAGRAM-1)

• Remove the screws by pulling them.(DIAGRAM-2)

• To the holes where the transport screws have been removed, insert

the plastic transport screw taps found in the accessories bag. (DIAGRAM-3)

• The transportation screws, that have been removed from the machine should be kept in hand for any other transportation necessities.

DIAGRAM-2 DIAGRAM-1 DIAGRAM-3

ADJUSTMENT OF FEET

• Do not install your machine on rugs or similar surfaces.

• For your machine to work silently and without any vibration, it should

be settled on a flat, non-slippery and tough ground.

• You can adjust the balance of your machine from its feet.

• First, loosen the plastic adjustment nut.

• Adjust by rotating the feet upwards or downwards.

• After the balance has been reached, tighten the plastic adjustment

nut again by rotating it upwards.

• Never put cartons, wooden blocks or similar materials under the machine to balance the irregularities on the level of the ground.

ELECTRICAL CONNECTION

• Your washing machine works with 220-240V and 50Hz.

• A special grounded plug has been attached to the network cable of

your washing machine. This plug must definitely be inserted to a grounded socket with 10 ampere. The fuse flow value of the electricity line attached to this should also be 10 ampere. If you have no such sockets and fuses in your house, let it be made by a qualified electrician.

• Our company will not be responsible for any damages that may occur as a result of usage without grounding.

WATER SUPPLY CONNECTION

• Your machine has a single water (cold) inlet.

• To prevent from the leakages on the connection joints, 1 seal is

included in the hose packing.(Fit this seal on the end of the water inlet hose at the tap side.)

• Connect the end with bracket of the water inlet hose to the water inlet valve at the rear of the machine and the other end to your tap. In situations where you are not assured, let a qualified plumber make the connection works.

• Water pressure of 1-10 bars from your tap will enable your machine to work more efficiently.(1 bar pressure means water flow of more than 8 liters in 1 minute from a fully opened tap).

• After connections are completed, check for the non-leakage of the connection joints by turning on your tap completely.

• Be sure that water inlet hoses are not folded, broken or crushed.

• Mount the water inlet hoses to a 3”/4, geared water tap.

Cold water inlet

WATER DRAIN CONNECTION

• Be sure that water inlet hoses are not folded, twisted, crushed or elongated by stretching.

• Water drain hose should be mounted at a height of minimum 60 cm, maximum 100 cm from the ground.

• The end of the water drain hose may directly be fitted to the dirty water outlet hole or a special apparatus mounted on the outlet bracket of the wash-stand.

• Never attempt to extend the water drain hose by adding extra parts.

SECTION 3:TECHNICAL SPECIFICATIONS

WM40T-1

Maximum dry laundry capacity (kg) 5 Recommended loading (kg) 4,5

Height (cm) 85 Width (cm) 59,6

Depth (cm) 51 Maximum spin cycle ( rpm ) 400

(*) Maximum spin cycles depend on the model you’ve chosen

1 2 3

7 1-Upper tray 5-Handle

2-Detergent drawer 6-Filter cover

3-Control panel 7-Kickplate

4-Door

SECTION 4:CONTROL PANEL

WM40T-1

1 2 3 4 5 6

7 8 9

1-Detergent drawer 6-Program knob 2-Start/pause light 7-Start/pause button 3-Function indicator lights 8-Function buttons 4-Temperature adjustment knob 9-Program end light 5-Program ready light

START/PAUSE BUTTON

Used to start a selected program or pause during running.

It is required for the program knob to be brought to O(off) position before selecting the program or changing a contin uing program.

WARNING!

FUNCTION INDICATOR LIGHTS

When the start/pause button or any function button is pressed,the corresponding light turns on.The light turns off when the function button or start/pause button is re-pressed, or when the process the selected function is completed.

The function indicator lights are also used in failure detection system mentioned in section 9.

FUNCTION BUTTONS No spin

This program is recommended to be used for your sensitive clothes on which no spinning should be done. By pressing this function button, you can cancel the spinning process which is included in the program.

Easy ironing

By using this function, you can ensure your clothes to come out less wrinkled after the washing.

WARNING!

Functions vary depending on the model you have chosen.If you forgot to use additional function and your machine starts to wash push the additional function button if the indicator light is on. Additional function will be activated.If the indicator light is not on,additional function will not be activated.

TEMPARATURE ADJUSTMENT KNOB

By the temparature adjustment knob, you can adjust the washing water temparature of your clothes between O(cold wash) and 90 ˚C. When you are selecting the washing water temparature, pay attention to the international washing signs on your clothes.

PROGRAM KNOB

With the program knob, you can select the program with which you desire to wash your clothes. You can adjust the program selection process by turning the program knob in both directions. You must be careful that the adjustment sign of the program knob is exactly on the program you want to select. When you bring the program knob to O(off) position, while your machine is running, your program will remain incomplete.

+ 19 hidden pages