Smeg WHTS1114LSSA User manual [GB]

Washing Machine User’s Manual

Lavatrice

Manuale utente

Wasmachine

Gebruiker Handleiding

WHTS1114LSSA

Document Number

2820526521_EN/ 30-04-18.(15:34)

1 General safety instructions

This section includes security instructions which may help prevent the injuries and material damage risks. All kinds of warranties shall be invalid if these instructions are not observed.

1.1 Life and property safety

Never place the product on a carpet-covered floor. Electrical parts will get

overheated since air cannot circulate from under the device. This will cause problems with your product.

Unplug the product if it is not in use.

Always have the installation and repairing procedures carried out by the

Authorised Service Agent. The manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

The water supply and draining hoses must be securely fastened and remain

undamaged. Otherwise, water leak may occur.

While there is still water inside the product, never open the loading door or

remove the filter. Otherwise, risk of flooding and injury from hot water will occur.

Do not force open the locked loading door. Door can be opened a few

minutes after the washing cycle ends. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.

Use detergents, softeners and supplements suitable for automatic washing

machines only.

Follow the instructions on the label of textiles and the detergent package.

1.2 Children's safety

This product can be used by the children who are at the age of 8 and

over and the people whose physical, sensory or mental skills are not fully developed or who do not have necessary required experience and knowledge as long as they are supervised or trained about the safe use of the product and its risks. Children should not play with the device. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.

Packaging materials may be dangerous for the children. Keep packaging

materials in a safe place away from reach of the children.

Electrical products are dangerous for the children. Keep the children away

from the product when it is in use. Do not allow them to play with the product. Use child lock to prevent children from intervening with the product.

2 / EN

Washing Machine / User’s Manual

Do not forget to close the loading door when leaving the room where the

product is located.

Store all detergents and additives in a safe place away from the reach of

the children by closing the cover of the detergent container or sealing the detergent package.

1.3 Electrical safety

If the product has a failure, it should not be operated unless it is repaired by

the Authorised Service Agent. Risk of electric shock!

This product is designed to resume operating in the event of powering

on after a power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.

Plug the product into a grounded outlet protected by a 16 A fuse. Do not

neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

Do not wash the product by spraying or pouring water onto it! Risk of electric

shock!

Never touch the power cable plug with wet hands! Do not grab the power

cord to unplug the machine, always unplug it by holding the socket with one hand, and pulling the plug with the other hand.

Product should be unplugged during installation, maintenance, cleaning

and repair procedures.

If the power cable is damaged, it must be replaced by the manufacturer,

after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.

1.4 Hot surface safety

Washing Machine / User’s Manual

While washing the laundry at high temperatures, the loading door glass will get hot. Considering this fact, during washing operation keep the children away from the loading door of the product to prevent them touching it.

3 / EN

Important instructions for environment

2.1 Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to

learn about these collection centers. Compliance with RoHS Directive: The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

2.2 Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Intended use

• This product has been designed for domestic use. It is not for commercial purposes or it should not be used out of its intended use.

• The product must only be used for washing and rinsing of laundry that are marked accordingly.

4 / EN

Washing Machine / User’s Manual

4 Technical specifications

Complying Commission Delegated Regulation (EU) No 1061/2010

Supplier name or trademark SMEG Model name WHTS1114LSSA Rated capacity (kg) 11 Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) A+++ Annual Energy Consumption (kWh) Energy consumption of the standard 60°C cotton programme at full load (kWh) 1,210 Energy consumption of the standard 60°C cotton programme at partial load (kWh) 0,920 Energy consumption of the standard 40°C cotton programme at partial load (kWh) 0,910 Power consumption in ‘off-mode’ (W) 0,440 Power consumption in ‘left-on mode’ (W) 0,640 Annual Water Consumption (l) Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency) B Maximum spin speed (rpm) 1400 Remaining moisture Content (%) 53 Standard cotton programme Programme time of the standard 60°C cotton programme at full load (min) 236 Programme time of the standard 60°C cotton programme at partial load (min) 190 Programme time of the standard 40°C cotton programme at partial load (min) 190 Duration of the left-on mode (min) N/A Airborne acoustical noise emissions washing/spinning (dB) 59/76 Built-in No Height (cm) 84 Width (cm) 60 Depth (cm) 65 Net weight (±4 kg.) 82 Single Water inlet / Double Water inlet

• Available Electrical input (V/Hz) 230 V / 50Hz Total current (A) 10 Total power (W) 2200 Main model code 9715

(1)

Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the

consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.

(2)

Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water

consumption will depend on how the appliance is used.

(3)

“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption.

Technical specifications may be changed without prior notice to improve the quality of the product.

(1)

(2)

(3)

Cotton Eco 60°C and 40°C

233

13200

• / -

Washing Machine / User’s Manual

5 / EN

4.1 Installation

• Apply to the nearest authorised service agent for the installation of your product.

• Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

• Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

• Make sure that the installation and electrical connections of the product are performed by authorised service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

4.1.1 Appropriate installation location

• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar surfaces.

• When the washing machine and dryer are placed on top of each other, their total weight –when loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product in the environments where the temperature falls below 0 ºC.

• Leaving a gap at the sides of the machine is suggested to reduce vibration and noise

• On a graduated floor, do not place the product next to the edge or on a platform.

• Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them on the product.

4.1.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Do not make this operation alone by yourself.

4.1.3 Removing the transportation locks

1 Loosen all bolts with an appropriate wrench until they turn freely. 2 Remove the transport safety bolts by turning them slightly. 3 Insert the plastic covers in the bag containing the user manual to the openings on the rear panel.

CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be

6 / EN

damaged.

Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

Install the transport safety bolts in reverse order of the disassembly procedure. Never move the product without the transportation safety bolts properly fixed in place!

Washing Machine / User’s Manual

4.1.4 Connecting water supply

40 cm

100 cm

The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure

reducing valve if water pressure is higher.

CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will

get damaged or the product will switch to protection mode and will not operate.

CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1 Tighten the nuts of the hose by hand. Never use a tool when

tightening the nuts.

2 When hose connection is completed, check whether there is leak

problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product.

4.1.5 Connecting the drain hose to the drain

• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.

CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there

is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine performs water intake and discharge processes without any problem, fix the drain hose securely.

• Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm.

• In case the drain hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.

• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.

• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

Washing Machine / User’s Manual

7 / EN

4.1.6 Adjusting the feet

CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced

1 Loosen the lock nuts on the feet by hand. 2 Adjust the feet until the product stands in a stable and balanced way.

3. Tighten all lock nuts by hand again.

4.1.7 Electrical connection

Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• Connection must comply with national regulations.

• The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements. Use of a Groud Fault Circuit Interrupter (GFCI) is recommended.

• Power cable plug must be within easy reach after installation.

• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.

• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

• Do not make connections via extension cables or multi-plugs.

on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems.

CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

4.1.8 Initial use

8 / EN

CAUTION: Damaged power cables must be replaced by the Authorised Service Agents.

Before starting to use the product make sure that the preparations are made which are in line with the “Important Safety and Environment Instructions” and the instructions in the “Installation” section. To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If this program is not available in your machine, apply the method which is described in the section 4.4.2.

Use an anti-limescale suitable for the washing machines.

Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.

Washing Machine / User’s Manual

+ 18 hidden pages