Smeg WF366LDX, WF366RDX User Manual

USER MANUAL

Wines Cellars

1

Index

Page

Important instructions for safety and the environment

For your safety
Respect for the environment

Installation

Installation
Connection to the electrical mains

Before starting

Getting to know the appliance
Main features
Main components
Electronic Control
Main control panel

Turning the appliance on and off

Turning on and off
How to adjust the temperature to suit various needs
Information and malfunction signals on the display

Settings and Special Functions

Customization and Language Settings
Special functions activated through the Menu
Basic settings of the Menu

Internal Layout

Internal Layout (positioning, adjustment, removal)

Lighting

Lighting

Use of the MultiZone compartment

Use of the MultiZone compartment
MultiZone compartment

Conservation of wines

General directions
Wine conservation temperature
Time of conservation

Recommended times for food conservation

Care and Cleaning

Care and Cleaning
Condenser cleaning
Internal cleaning

Troubleshooting guide

Troubleshooting guide
Malfunction indications appearing on the display

Smeg Access Menu Map

Functions
Settings

1

B09001301

Product tested in accordante with EN62471

Risk Group 2

PRUDENZ A:

NON FI SSARE LA LAMPADA IN FUNZIONE .

PUÒ ES SERE DANN OSO PER GLI OCC HI.

CAUTION:

DO NOT STARE AT OPERATIN G LAMP.

MAY BE HAR MFUL T O THE EYES.

Important instructions for safety and the environment

1.1

For your safety

Notes

Suggestions for proper use
of the appliance

If this appliance is replacing an existing appliance which must be
removed or disposed of, make sure that it does not become a dan­gerous trap for children by cutting its power supply cable and ren­dering it impossible to close the door. Use the same caution at the
end of the lifespan of the new appliance.

This appliance is designed to refrigerate beverages and foods and
is destined for domestic use.

The appliance must be installed by following the instructions in the
Installation Guide, particular care should be taken not to obstruct the
vent openings of the appliance and of the built-in units.

The appliance features a concentrated lighting system with LED
lamps. Do not stare into these lamps when they are on to avoid pos­sible eyesight damage.
This warning is also contained on the label attached to the inside of
the refrigerator door.

When the freezer is functioning do not touch the inner surfaces in
stainless steel with wet or damp hands, since skin may stick to the
very cold surfaces.

Do not use any type of electrical equipment inside of the food
conservation compartments.

When positioning the shelves, do not place fingers in the shelf
slide guides.

Do not position containers of ammable liquids near the appliance.

Important

Instruction to prevent damage
to the appliance

Warning

Instructions for preventing
personal injury

Completely switch off the appliance and unplug the power supply
cable during cleaning operations. If the plug is not easily reached, it
is a good idea to disconnect the omnipolar switch that controls the
socket that the appliance is connected to.

The packaging parts can be dangerous for children: do not allow

children to play with the plastic bags, plastic lm or Styrofoam.

Any repairs must be performed by a qualified Smeg Service tech­nician.

This appliance is not intended for use by persons (including children)
with reduced physical, sensory or lack of experience and knowledge
unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.

Do not damage the appliance refrigerant circuit pipes.

Do not store explosive substances such as aerosol cans with a am­mable propellant in this appliance.

2

2

Installation

Respect for the environment

Make sure you dispose properly of all packing materials.

The appliance must not be disposed of with urban waste.
Contact local waste disposal authorities for information on the disposal
of recyclable waste.

For disposal, cut the power supply cord and make it impossible to
close the door.

During disposal, avoid damage to the refrigeration circuit.

Neither the refrigeration circuit nor the insulation contain substances
that are hazardous to the ozone layer

Installation

Make sure that installation is performed correctly, adhering to all of

the instructions in the specic installation guide provided with the

appliance.

1.2

2.1

Do not use extension cords and/or multiple
adapters for connection.

Connection to the electrical mains

The appliance is equipped with a Schuko type 16A plug.

It must be connected to the electrical mains by means of a corre­sponding Schuko socket.

Do not use extension cords and/or multiple adapters for connection.

2.2

3

4

3

Before starting

3.1

Getting to know the appliance

Congratulations for having purchased your new Smeg:
from now on you can use our innovative conservation
system, which will allow you to keep all of your food in the
best way possible.

This manual will answer most of your questions about the
product’s features. Should you require further information,
please check our website

www.smeg.com

3.2

The Smeg triple refrigeration system ensure perfect con-

ditions for conservation of various types of wines

The electronic control guarantees constant temperature

and humidity levels set by the user

The double compressor allows separate management
of the set temperature and humidity for the Cantina, Wine
Cellar and MultiZone compartments

The MultiZone compartment may operate in three dif­ferent modes: as a freezer, as a refrigerator or as a cooler
compartment

An interactive menu (Menu) permits personalized man­agement of appliance functions and the display of mes­sages on operation

Main features

Optimization of consumption during vacation periods

Patented hinge system that permits automatic door closing

MultiZone drawers with Soft self-closing system

Localized lighting system with LEDS

Anti-tipping system with brackets for wall mounting.

5

Before starting

3

1

2

3

Cantina

4

5

10

Main components

One drawer Wine Cellar

1 Structure in stainless steel

with aluminium trim

2 Wine Cellar and MultiZone

control panels with Menu

7

8

9

3 Sliding bottle shelfs,

mounted on wheels for
easy extraction

4 Cantina area control panel

5 Wine Cellar

6 Frezer compartment that

can be transformed into
a refrigerator or Low Temp
compartment

(MultiZone function)

7 Double refrigeration system

8 Temperature display

3.3

Wine Cellar

MultiZone

6

11

12

9 Acoustic signals

10 Vacation function

(in Menu)

11 Innovative lighting

12 Automatic door and

drawer closure

3

10 11 12 13

123456798

3.4

The innovative electronic control system designed by Smeg maintains constant temperature on the three compartments
and visualizes it on the control panel display. It also allows user interaction making it possible to personalize settings of the
various functions and to receive sound and/or visual messages should any malfunction occur in the appliance.

3.5

Before starting

Componenti principali

Electronic Control

Componenti principali

Main control panel

3.3

3.3

1

2

3

4

5

6

7

8

9

Unit

Wine cellar

Menu

Up/down
Wine Cellar

Display

Up/Down
(MultiZone)

Enter

Alarm

Light

Allows complete shutdown and start-up of the appliance
(press for three seconds).

Allows switching on and off only the Wine Cellar compartment (press
for three seconds).

Allows access to the appliance functions menu.

Using the Up and Down buttons, it is possible to change the set tem­perature of the refrigerator and scroll through the interactive menu.

Displays the temperature of the Wine Cellar and MultiZone compart­ments, the date and time, Menu functions and visual messages.

By selecting Up/Down the preset temperature can be changed ac­cording to the selected function mode (freezer, refrigerator, Low
Temp).

Conrms activation or deactivation of the selections made in the

Menu.

Allows activating or deactivating the automatic ice production.

Allows illumination of the Wine Cellar and Cantina compartments also
when the door is closed. Once activated, the light of the top compart­ment will automatically shut off after 6 hours.

10

11

12

13

Display

Up/Down
Cantina

Cantina

Humidity

Shows the temperature of the Cantina compartment.

Using the Up and Down keys, it is possible to change the set tempera­ture for the Cantina compartment.

Allows switching on and off only the Cantina compartment on or off
(press for three seconds).

Allows adjustment of humidity in the Wine Cellar and Cantina com­partments to three levels: High (HI), Medium (A) and Low (LO).

6

7

Turning the appliance on and off

4

First start-up

Turning off the Wine Cellar compartment

Turning the Wine Cellar compartment on

again

Turning on and off

When the appliance is connected to the electrical power supply but
has not yet been turned on, the display shows the message

This is a safety message to warn that power is supplied to the appli­ance, while all of the keys on the panel are off.
To switch on all the appliance compartments, press the Unit button
for three seconds.

Once you have turned on all of the compartments of the appliance,
you can turn off only the wine cellar compartment by pressing the
relevant key for three seconds.

The MultiZone compartment is always on and cannot be turned off
except by completely turning off the appliance.

Press again for three seconds the relevant key.

4.1

Complete shutdown

Lengthy shutdown periods

To prevent accidental modication of settings,

the keypad locks automatically after a certain
period of time and the display shows the mes­sage “keypad locked”. To re-activate it, simul­taneously press the keys Menu and Up/Down
(Down) for three seconds.

At the rst start-up, if the message Standby does
not appear, it means that the appliance has al-

ready started the cooling process. If this is the

case, deactivate any possible acoustic signals

by pressing the Alarm key , close the door and
wait until the set temperature is reached.

During the rst start-up, you will not be able to use

the Menu to modify factory settings until the de­fault temperature has been reached. It is howev­er possible to set the time and date immediately;
these parameters are required to activate some
of the special functions.

To shut down the unit completely for cleaning or maintenance, press
the Unit key
Also take the plug out of the socket and turn off the omnipolar switch
that powers it.

After you have completely shut down the appliance and unplugged
it, empty it of all its contents, clean it and dry it. Leave the doors and
the drawers ajar to prevent the formation of unpleasant odours.

for three seconds.

If only the Cantina or Wine Cellar compartment

is turned off, the corresponding fan will continue

to run independently to prevent the formation of
unpleasant odours and mould.

4

Turning on the appliance

4.2

How to adjust the temperature for suit various needs

To adjust the temperature in the various compartments, use the up/
down key for that compartment (see chapter 3.5).
If the “keypad locked” message appear, simultaneously press the keys
Menu and Up/Down (Down) for 3 seconds.

Wines compartment

Each model has been carefully tested before leaving the factory and
is adjusted so as to ensure high performance and low consumption.
The ideal temperature for wine conservation does however depend
on the types of wine you want to conserve, the method of conserva­tion (Wine Cellar for conservation and consumption, or Cantina for the
conservation and aging of prized bottles).
It also varies according to personal taste.
Please refer to the guide on wine conservation included further ahead
in this manual.

As needed, you can reset the temperatures as follows:

Cantina Compartment:
from +10° C to +18° C (from 50° F to 53.6° F).
The default temperature is +12° C (53.6° F).

Wine Cellar compartment:
from +4° C to +12° C (from 39.2° F to 53.6° F).
The default temperature is +10° C (50° F).

MultiZone compartment

If the “keypad locked” message appear, simul­taneously press the keys Menu and Up/Down

(Down)

The displayed temperature may vary slightly
with respect to the set temperature if the doors
are continuously opened or insertion of room
temperature food or large quantities of food.

It takes 6 to 12 hours to reach the selected tem­perature.

4.4

for 3 seconds.

Information and malfunction signals on the display

The MultiZone compartment is default set to freezer mode but it can
also be set to run as a refrigerator or cooler compartment.
Instructions for conversion are provided in the paragraph on special
functions and settings.

As needed, you can reset the temperatures as follows:

Freezer compartment: from -15° C to -22° C (from 5° F to -7.6° F).
The default temperature, which is recommended, is -18° (0° F)

Refrigerator compartment: from +2° C to +8° C (from 35.6° F to 46.4° F).
The default temperature, which is recommended, is +5° C (41° F).

Cooler compartment: from -2° C to +2° C (from 28.4° F to 35.6° F),
The default temperature, which is recommended, is 0° C (32° F).

An integrated control system provides information through luminous
signals or text messages shown on the display.

The information signal is always displayed with a xed text message,

while a malfunction signal is shown with blinking text.
The acoustic signal that accompanies some malfunction signals can be
deactivated by pressing the Alarm key on the main control panel.
The list of malfunction signals is located in the back of this manual.

8

9

Functions Shopping Multiz
Shopping Multizone ON/OFF Shopping ON

Functions Shopping Multiz
Shopping Multizone ON/OFF Super Cool OFF

Functions Shopping Multiz
Shopping Time Set Hours: I

Settings and Special Functions

5

To prevent accidental modication of settings,

the keypad locks automatically after a certain
period of time and the display shows the mes­sage “keypad locked”.

To re-activate it, simultaneously press the keys

Menu
three seconds.

and Up/Down (Down) for at least

Customization and Language Settings

It is possible to customized the functions of your Smeg to adapt it to di­verse usage needs, resetting the main parameters (Settings) or activating
special functions (Functions).
Functions are visualized on the main display by pressing the Menu button

.

The Up/Down buttons permit scrolling the available functions, which can
be selected by pressing the Enter button . The display visualizes the cur­rent functioning status.
Using the Up/Down buttons , it is also possible to scroll through the select­ed function, activating or deactivating by pressing the Enter button .

Once the function is conrmed, the display will automatically visualize the

main menu to select other functions.
At any time it is possible to return to the previous selection through
the Menu button .

The language of the messages appearing on the display can be changed
by operating as follows:
Enter the Menu by pressing the Menu button select Settings via the Up/
Down buttons and conrm via Enter .
Then select the Language function and the desired language.

Special functions activated through the Menu

5.1

5.2

Shopping MultiZone

How to activate

How to deactivate

How to program timed activation

To use special functions, select the Menu key
key to access the menu, conrming the selection
.

This function must be activated at least 24 hours before inserting room
temperature items into the freezer, or several hours before placing into
the freezer previously frozen items which have been subject to a slight
temperature rise. This function is automatically deactivated when the
programmed time period expires.
It is possible o program timed activation of the function.
After a prolonged interruption of the electrical power, it is necessary to
reactivate the function.

and use the Up/Down

Functions Hodiday Multiz
Holiday Multizone ON/OFF Holiday ON

Functions Hodiday Multiz
Holiday Multizone ON/OFF Holiday OFF

Functions Hodiday Multiz
Holiday Time Set Days: I

Functions Sabbath Mode
Sabbath Mode ON/OFF Sabbath Mode ON

Functions Sabbath Mode
Sabbath Mode ON/OFF Sabbath Mode OFF

Functions Bottle Cooler
Bottle Cooler ON/OFF Bottle Cooler ON

Functions Bottle Cooler
Set Cooling Time Set Time : 20 min

Functions Bottle Cooler
Bottle Cooler ON/OFF Bottle Cooler OFF

Settings and Special Functions

5

Vacation MultiZone

How to activate

How to deactivate upon re-entry

How to program the duration

Bottle Cooler

This function (recommended in case of prolonged absences since it
allows considerable energy savings) brings the Tri-Mode compartment
temperature to - 18°C (46.4°F).
It is possible to program the duration, or it can be manually deacti­vated upon re-entry after a period of absence.
This function remains active even if during the period of absence there
is a prolonged interruption of electrical power.

It is possible to program a period from 1 to 90 days.

This function can be activated when it is necessary to cool off bever­ages quickly, by placing them inside the freezer compartment.
It is possible to select a duration of 1 to 45 minutes. A sound signal will
indicated when the optimal temperature has been reached.
After removing the beverages, deactivate the sound signal by press­ing the Alarm button

.

How to activate

How to deactivate

How to program the duration

Sabbath Mode (Optional)

How to activate

How to deactivate

The function makes it possible to comply to certain religious observ­ances requiring that the operation of the appliance is not affected by
the opening or closing of the doors (the thermostatic control, the inner
lighting and the ice maker are deactivated).

10

11

Settings Default Setting
Enter to confirm

Settings DateSet Date

DATE: 01-01-2009

Settings DateShow Date

DATE: 01-01-2009 On

Settings DateShow Date

DATE: 01-01-2009 Off

Settings Multizone Options
Fridge Enter to confirm

Settings Multizone Options
Fresco Enter to confirm

Settings Multizone Options
Freezer Enter to confirm

Settings and Special Functions

5

MultiZone Options

How to set the Fridge function

How to set the Low Temp function

How to revert to the Freezer function

Default Setting

How to reset default settings

Basic settings of the Menu

Select the Menu button
to select .

The freezer compartment can, if required, be converted to the refrig­eration o Low Temp operating mode.

This offers the possibility to reset default factory settings and cancels
any previous changes.

and used the Up/Down button

5.3

ATTENTION: If the default settings are restored, it is

necessary to reactivate the choice of operation of
the MultiZone compartment in case it was previously
set as Fridge or Fresco.

How to set the date

Show Date

How to activate the date

How to deactivate the date

Date

Set Date

The display will visualize the date in the format dd:mm:yy (day:month:year),
the day will blink. Use the Up/Down buttons

rm with Enter to go on to the next setting; once the year is conrmed

the date will be set.

Using this function it is possible to deactivate/activate the date visuali­zation on the display.

to modify the setting, con-

Settings Time Set Time

TIME: 01:01

Settings Time Set View
Set: 12

Settings Time Set View
Set: 24

Settings Time Show Time

TIME: 01:01 On

Settings Time Show Time

TIME: 01:01 Off

Settings and Special Functions

5

How to set the time

How to set the display to 12 h

How to set the display to 24 h

Time

Set Time

The display visualizes the hours and minutes in the format hh:mm and
with hh: blinking. Use the Up/Down buttons

then conrm by pressing Enter
Once the minutes are conrmed, the time will be set.

This function selects the display at 12 or 24 h.Set 12/24

to go on to the next setting.

to modify the setting and

Show Time

How to activate the permanent time

How to deactivate

Through this function it is possible to activate/deactivate the constant
visualization of the time.

12

13

Settings Language italiano

Settings Language english

Settings Language français

Settings Language deutsch

Settings Language español

Settings Set ‘C

Settings Set ‘C/’F

Set ‘C/’F

Set ‘F

Settings ShowRoom Mode

ShowRoom Mode

On

Settings Off

Settings Child Lock

Child Lock

On

Settings Off

Italian

English

French

German

Spanish

Settings and Special Functions

The function allows selection of the language for the display messages.Language

5

Set °C/°F

How to set the temperature in Centigrade

How to set the temperature in Fahrenheit

Showroom Mode

How to activate

How to deactivate

Child Lock

How to activate

How to deactivate

This function permits visualizing the temperature in Centigrade or Fahr­enheit degrees. Normally, the appliance is set for visualization in cen­tigrade degrees.

6

Internal Layout

6.1

Internal Layout (positioning, adjustment, removal)

Wine shelf

MultiZone drawer

The shelves can be easily removed for cleaning.
Remove the bottles, completely extract the shelf, tilt it upward
until the wheels are free of their seat and extract it.

Fixed to the slide guides with two locking nuts

to remove the drawer, unscrew the locking nuts and remove the
drawer.

to remove the inner MultiZone drawer unscrew the locking nuts.

14

15

Lighting

7

Lighting

To provide optimum interior lighting, LED strips illuminate the refrig­erator compartment from the top and sets of LED lights directly il­luminate different areas of the refrigerator compartment, of the Low
Temp drawers and the freezer drawer.

In case of malfunction and/or failure of the lighting system, you
should contact an authorized Smeg Service Agent.

7.1

Once activated, the light of the top compartment

will automatically shut off after 6 hours.

Use of the MultiZone compartment

8

Use of the MultiZone compartment

8.1

Freezer mode

Refrigerator mode

The MultiZone compartment, used in conjunction with the Wine Cellar
and Cantina compartment, allows great exibility in the use of the ap­pliance.

Some possible uses:

Liquors, such as vodka, gin, tequila, schnapps, limoncello and the
glasses to serve them

Rapid cooling of beverages, by activating the bottle cooler function

Storage of large amounts of ice.

As expansion of the Wine Cellar or of the Cantina

For refrigeration of beer and soft drinks

Cooler mode

For storage of cold dishes and snacks.

For conservation of ham, salmon

gourmet preparations.

It comes without saying that, the compartment can be used in a tra­ditional manner. Suggestions and instructions are provided to offer
you best conservation of your food over time in complete safety.

8.2

16

17

Conservation of wines

9

Wine Cellar

General directions

As is known, wine can be stored for long periods of time if this is done
under the following conditions:

Suitable temperature without appreciable variations over time

Controlled level of humidity

Protection from light

Absence of noise and vibrations

Absence of odours

Bottle kept horizontal.

All of these conditions are fully met in the Smeg Wine Cellar.

Conservation temperature

The space offered by the Wine Cellar and Cantina compartments,
which can be expanded as necessary by using the MultiZone com­partment as a wine cellar, allows conservation of your best wines at
three different temperatures.

The three compartments are initially set to the following temperatures:

9.1

9.2

Cantina

MultiZone

Models with Cantina and Wine Cellar

Cantina compartment
+12° C (53.6° F) - adjustable from +4° C to +18° C (from 39,2° F to 64,4° F)

Wine Cellar compartment
+10° C (50° F) - adjustable from +4° C to +18° C (from 39,2° F to 64,4° F)

MultiZone drawer

-18° (0° F) - adjustable from -15° C to -22° C (from 5° F to -7.6° F)
(freezer mode)

To transform the MultiZone compartment into a wine cellar space, you
must access the Menu, set it as a refrigerator compartment, and ad­just it to a temperature between +4° C and +8° C (from 39.2° F to 46.4°
F).

All the temperatures can be modied according to the characteristics

of the wines and personal preferences. However, you should attempt
to keep the temperature as constant as possible over time.

Rapid and large-scale temperature variations can in fact cause dila­tion of the liquid and early aging of the wine.

You should also avoid very low temperatures (below 4° C - 39.2° F )
which may lead to the formation of deposits and damage the aes­thetic qualities of the wine.

All the compartments offer optimal conditions and take into account
all these needs. It should however be noted that the Cantina com­partment, in particular, is thermostatically controlled in a very precise
manner and ensures the utmost care and attention over time of your
most prized bottles.

18

Conservation of wines

9

Time of conservation

9.3

TYPE OF WINE CONSERVATION TEMPERATURE TIME OF CONSERVATION

New wines (Vin Nouveau) from 12° to 14° C 6 months

Sweet sparkling wines from 8° to 10° C 1 year

Rosé from 10° to 14° C 1 year

Semi-sparkling wines from 10° to 12° C 1 - 2 years

Normal white wines from 10° to 14° C 1 - 2 years

Light red wines from 12° to 14° C 2 years

Dry sparkling wines from 8° to 10° C 2 years

Classic sparkling wines from 8° to 10° C 3 - 4 years

Barrique and Vigorous white wines from 8° to 12° C 3 - 5 years

Normal red wines from 14° to 16° C 3 - 5 years

Barrique and Vigorous red wines from 14° to 18° C 7 - 10 years

Straw wines or Liquorous wines from 16° to 18° C 10 - 15 years

Improvement of wine over time and its duration usually depends on
the character of the variety and its type.
The following chart shows the best period of conservation and ag­ing for various types in ideal conservation conditions offered by your
appliance. However, you should always follow the instructions of the

winemaker, especially for ne wines.

18

19

Recommended times for food conservation

Fresh foods Conservation area Time

Raw meats

Large cuts Cooler Compartment 4 days

Steaks, poultry and wild game Cooler Compartment 3 days

Ground meat Cooler Compartment 1-2 days

Carpaccio Cooler Compartment Immediately

Cooked meat

Boiled meat and roasted meat Refrigerator Compartment 2 days

Meat sauce Refrigerator Compartment 6 days

Raw and cooked sh Cooler Compartment 2 days

Soups and broths Refrigerator Compartment 2 days

Pasta Refrigerator Compartment 2 days

Opened cold cuts Refrigerator Compartment 3 days

10

Fresh cheeses Refrigerator Compartment 2-3 days

Well protected aged cheeses Refrigerator Compartment Several months

Eggs (fresh and unwashed) Refrigerator Compartment 15 days

Opened containers Refrigerator Compartment 2-3 days

Raw vegetables (in perforated bags) Refrigerator Compartment 3-6 days

Frozen foods Conservation area Time

Beef, veal, lamb and goat Freezer Compartment (steaks) 6-12 months

Beef, veal, lamb and goat Freezer Compartment (Meat with bone) 4-6 months

Ground beef Freezer Compartment 1-2 months

Pork Freezer Compartment (Without bone) 4-6 months

Pork Freezer Compartment (With bone) 2-3 months

Ground pork Freezer Compartment 1-2 months

Meat leftovers Freezer Compartment 2-3 months

Whole chicken and turkey Freezer Compartment 8-12 months

Goose, duck and pheasant Freezer Compartment 4-8 months

Fish Freezer Compartment 1-2 months

Crustaceans Freezer Compartment 2-3 months

Cooked foods Freezer Compartment 1-2 months

Vegetables Freezer Compartment 8-12 months

Fruit Freezer Compartment 6-12 months

Desserts and cakes Freezer Compartment 2-3 months

11

Care and Cleaning

11.1

Scrupulously follow the detailed directions that
can be found in the provided kit and never
use abrasive or metallic products which could

scratch and damage the satin nishing on the

appliance permanently.
Before performing any sort of cleaning, discon­nect the appliance from the electrical power
supply. Make sure you do not damage the re­frigerant circuit in any way.

11.2

Care and Cleaning

Condenser cleaning

To clean the parts in steel use a microfiber cloth and the sponge pro­vided in the kit with the appliance.

Always use the cloth and sponge in the direction of the steel’s satin nish.

Every now and then, to make to steel shiny, wipe with a slightly damp
microfiber cloth.

Do not use the sponge on aluminium parts, such as the handles and
the profiles of the glass shelves.
You should use special care to keep free of obstructions the ventila­tion openings in the appliance or in the cabinet that houses it.

A ventilation grille is located either at the top of the appliance or at the
bottom according to the model type.
A foam lter is placed behind the grille to protect from dust the ventila­tion system.
To clean it use a vacuum cleaner with a soft brush attachment at maxi-

mum power, sweeping it along the vent slits. In case of a signicant dust

build up, the ventilation grille can be removed to allow a more accu-

rate cleaning of the lter.
Take care also to check the condition of the nned condenser and

clean it from dust if needed.

The edges of the condenser are sharp, there­fore use adequate protection for the hands and
arms when cleaning the condenser.

11.3

Do not use water on the electrical parts, lights

and control panel.

Internal cleaning

Operate as follows:

Switch off the appliance by pressing the Unit button on the main

control panel for approx 3 seconds.

On models with ventilation at the base remove the grille at the bottom
and take it off. On models with ventilation at the top the grille (mag­netically attached) lift as shown in the picture.

Thoroughly clean the grille and the foam lter, by means of a vacuum

cleaner and the soft brush attachment.

Wait approx 30 minutes, until the nned condenser cools down to

room temperature, then clean it thoroughly from any dust build up as
shown in the picture, taking care not to damage it.

Start up the appliance again, by pressing the Unit button on the
main control panel for approx 3 seconds.

Clean the internal and removable parts by washing them with a so­lution of lukewarm water, a small amount of dishwashing detergent
and a pinch of baking soda.

Rinse and dry right away.

Do not use mechanical devices or other methods to speed up de­frosting.

Do not bring cold glass parts into contact with
boiling water.
Do not wash any parts of the refrigerator in a
dishwashing machine since this could damage
or irreparably deform the parts.

20

Troubleshooting guide

12

Malfunction message

The appliance does not work

The internal temperatures are

higher than normal

The appliance remains in function for a long

time period

Troubleshooting guide

If you notice malfunctions in your appliance, use this guide before calling
Service. This guide may help you resolve the problem yourself or could
provide important information to ensure rapid and effective service.

A malfunction is usually indicated on the display.
Problems that cannot be resolved by the user are signalled through a
malfunction code.

Is the appliance connected to the electrical power supply?
Does electrical power arrive at the electrical socket?
Is the Unit key
Is the condenser clean?

Does the display show a malfunction code?
Is the temperature adjusted correctly?
Is the condenser clean?
Were the doors or drawers open for a long period of time?
Were large quantities of food recently inserted?

Bear in mind that during a very hot weather and with very high tem­peratures in the room it is normal that the compressor remains in op­eration for prolonged periods of time.
Were the doors or drawers open for a long period of time?
Were large quantities of food recently inserted?
Is the condenser clean?
Check that the doors are closed and that the food or containers do
not obstruct the perfect closure of the door.

activated?

12.1

If you hear strange noises

Condensation forms both inside and out

The Refrigerator or Freezer has frost or ice

Unpleasant odours inside the refrigerator

The doors are difcult to open

It is normal to hear noise from the fans or compressors during the
defrost phase.
Noise could be louder depending on the position of the appliance
and the surrounding environment.

If the climate is very humid, the formation of condensation is normal.
Opening the door or drawers for prolonged periods of time can con­tribute to the formation of condensation.
In any case, make sure that the doors are always perfectly closed.

Did you leave the doors open for a long period of time?
Do the doors close perfectly?
If the doors do not close perfectly, contact your installer.

Clean the appliance completely as indicated in this manual.
Hermetically cover all the food. Do not conserve food for prolonged
periods of time.

The appliance was designed to permit hermetic closure.
When the door is closed, a vacuum situation can occur: in this case it
is necessary to wait a few seconds until the pressure balances before
opening the door.

21

12

Troubleshooting guide

12.2

Malfunction indications appearing on the display

Display message Malfunction description

Power Failure Prolonged interruption of electrical power

Door open Door open

Drawer open Drawer open

Cellar too warm Cellar (Wine Cellar) compartment too warm

Cellar too cold Cellar (Wine Cellar) compartment too cold

Cantina too warm Cantina compartment too warm

Cantina too cold Cantina compartment too warm

Fridge too warm MultiZone compartment (refrigerator mode) too warm

The appliance starts up again automatically and indicates the highest recorded temperatures

this message appears few minutes from the door opening

this message appears few minutes from the drawer opening

See the troubleshooting guide

Wait 12 hours. If the problem persists, contact Customer Care

See the troubleshooting guide

Wait 12 hours. If the problem persists, contact Customer Care

See the troubleshooting guide

Fridge too cold MultiZone compartment (refrigerator mode) too cold

Cooler too warm MultiZone compartment (cooler mode) too warm

Cooler too cold MultiZone compartment (cooler mode) too cold

Freezer too warm MultiZone compartment (freezer mode) too warm

Freezer too cold MultiZone compartment (freezer mode) too cold

Error Code... Functional problems

Wait 12 hours. If the problem persists, contact Customer Care

See the troubleshooting guide

Wait 12 hours. If the problem persists, contact Customer Care

See the troubleshooting guide

Wait 12 hours. If the problem persists, contact Customer Care

call Customer Care who may help you to salve the problem or put you in contact with the
nearest Service Agent

22

Menu Map

13

Shopping MultiZone

Shopping ON/OFF

Shopping Time

Functions

Shopping MultiZone Off

Shopping MultiZone On

Set Hours: 1

13.1

FUNCTIONS

Vacation MultiZone

Bottle Cooler

Set Sabbath Mode

Vacation ON/OFF

Vacation Time

Set Cooling Time

Cooler ON/OFF

Sabbath Mode Off

Sabbath Mode On

Vacation MultiZone Off

Vacation MultiZone On

Set Days: 1

Set Time: 20 min

Bottle Cooler Off
Bottle Cooler On

23

13

Menu Map

13.2

Settings

Multiz Options

Default Setting

Date

Freezer
Fresco

Fridge

Enter to Conrm

Set Date

Show Date

Set Time

DATE: 01-01-2009

DATE: 01-01-2009 On

DATE: 01-01-2009 Off

TIME: 01:01

SETTINGS

Time

Language

Set °C/°F

Child Lock

Show Time

Set View

italiano

english

français

deutsch

español

Set °C

Set °F

ON

OFF

TIME: 01:01 On

TIME: 01:01 Off

Set: 24

Set: 12

24

ON

Showroom Mode

OFF

22-12-2014

SMEG W EN

INSTALLATION GUIDE

IMPORTANT

Dimensions in parentheses are in inches.

Weights in parentheses are in pounds.

Temperatures in parentheses are in Fahrenheit degrees.

1

Installation Guide

Page

Important Instructions

Important safety instructions

2

Children safety

Technical requirements

Appliance features and installation requirements

4

Installation niche features: Integrated

5

Installation niche features: Free-Standing

6

Preparing to install

Transport to installation site and unpacking

7

Electrical and Water connection

8

Levelling

11

Index

Panels mounting

Decorative door and Bottom-Drawer panels layout

12

Decorative panels layout for Fridge with one Bottom-Drawer

14

Decorative panels layout for Fridge with Glass door and one Bottom-Drawer

15

Panels Dimensions One Bottom - Drawer (models)

16

Mounting panels to the door and the drawer

17

Installation

Built-in installation of single appliance

19

Built-in installation of two or more appliances

20

Free-standing installation two or more appliances

22

Completing the installation

Anti-tipping safety assembly

23

Mounting the handles on stainless front

26

Ventilation

27

Post installation control

29

Start Up

30

1

2

3

Installation Guide

Symbols used in the Guide

Important safely instruction

Note

Tips for the correct use of the
appliance

Important

Directions to avoid appliance
damage

Warning

directions to prevent injury

Children safety

If this appliance is replacing an existing appliance which must be
removed or disposed of, make sure that it does not become a
dangerous trap for children by cutting its power supply cable and
rendering it impossible to close the door.
Use the same caution at the end of the lifespan of the new ap­pliance.

4

Appliance features and installation requirements

Appliance dimensions

Integrated

60 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)
75 Series w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)
90 Series w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)

Appliance dimensions

Free-Standing

Appliance dimensions

Integrated

Appliance dimensions

Free-Standing

Weight with packaging

Voltage

Power supply cable

Potable water supply pressure

Water supply tube

Provided installation accessories

Additional equipment necessary

60 Series w: 586 mm (23”)/ h: 2120 mm (84”)/ d: 635 mm (25”)
75 Series w: 736 mm (29”)/ h: 2120 mm (84”)/ d: 635 mm (25”)
90 Series w: 8869 mm (34 7/8”)/ h: 2120 mm (84”)/ d: 635 mm (25”)

60 Series w: 650 mm (25 5/8”) / h: 2210 mm (87”)/ d: 800 mm (31 1/2”)
75 Series w: 800 mm (31 1/2”)/ h: 2210 mm (87”)/ d: 800 mm (31 1/2”)
90 Series w: 950 mm (37 3/8”) / h: 2210 mm (87”)/ d: 800 mm (31 1/2”)

60 Series w: 650 mm (25 5/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
75 Series w: 800 mm (31 1/2”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
90 Series w: 950 mm (37 3/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)

60 Series up to 230 kg (507 lb)
75 Series up to 275 kg (606 lb)
90 Series up to 295 kg (650 lb)

Europe Version: AC 220-240V 50 Hz / North America Version: 110V 60Hz

Europe Version: Schuko 16 A plug / North America Version: 15 A

from 0.1 MPa to 0.5 MPa (1 Bar - 5 Bar)

3/4” female attachment

Customized panels mounting Kit

Anti-tipping Kit (B04000200)

Lateral connecting kit (KCLIT/KCLIH)

4 mm (1/8”) allen wrench

Phillips head screwdriver

wood and percussion drill

2.5 mm (1/8”) bit for wood

8 mm (3/8”) bit for walls

17 mm (3/4”) wrench

5

min 2064 (81 )

A A

E W E W

140 (5 ) 140 (5 )

100 (4”)

100 (4”)

RI96: 900 (35 )

WI66: 600 (23 )

RI76: 750 (29 )

A

992 (39”)

RI96: 1470 (57 )

RI76: 1320 (52”)

WI66: 1170 (46”)

RI96: 160 (6 )
RI76: 125 (5”)
WI66: 90 (3 )

560 (22”)

610 (24”)

RI96: 899 (35 ”)
RI76: 749 (29 ”)

WI66: 599 (23 ”)

10 (”)

105°

90°

610 (24”)

560 (22”)

610 (24”)

560 (22”)

1293 (50 )

474 (18 )

231 (9



) +

25 (1”)

500 (19 ) 500 (19 )

248 (9



)

+ 25 (1”)

231 (9



) +

25 (1”)

248 (9



)

+ 25 (1”)

20 ()

15 ()

15 ()

20 ()10 (”)

721 (28 ”) +25 (1”)

2050 (80 ”) +25 (1”)

2050 (80 ”) +25 (1”)

846 (33 ¼”) +25 (1”)

1168(46”)

330 (13”)

259 (10



)

1T/0T 0H

Installation Guide

area to be left clear for the anti-tipping brackets

E

area to be left clear for the power supply cable

W

and water supply hose

Minimum Niche Height

2064 mm (81 1/4”)

Installation niche features: Integrated Series

Door Opening Angle

105°

Width

RI96: 899 mm (35 3/8”)
RI76: 749 mm (29 1/2”)
WI66: 599 mm (23 5/8”)

Minimum Niche Width

RI96: 900 mm (35 1/2”)
RI76: 750 mm (29 5/8”)
WI66: 600 mm (23 3/4”)

Door Swing Clearance

RI96: 1470 mm (57 7/8”)
RI76: 1320 mm (52”)
WI66: 1170 mm (46”)

Height

2050 mm (80 3/4”)

+ 25 mm (1”)

Depth with door (without panel)

610 mm (24”)

Important: A 90° door opening

is sufcient to allow opening

and full extraction of the inner
drawers, even if the appliance
is installed directly adjacent to
a wall. Should an opening at
105° be desired, then the ap­pliance should be positioned
at the distance from the wall

described in gure.

6

min 10 ()

A A

min 2134 (84”)

140 (5 ½”) 140 (5 ½”)

100 (4”)

100 (4”)

E W E W

RF396: 890 (35”)

WF366: 590 (23 ¼”)

RF376: 740 (29 ½”)

1016 (40”)

RF396: 1470 (57 )

RF376: 1320 (52”)

WF366: 1170 (46”)

RF396: 230 (9)
RF376: 195 (7 )
WF366: 160 (6 )

560 (22”)

75 (3”)

RF396: 886 (34 ”)

RF376: 736 (29”)

WF366: 586 (23”)

10 (”)60 (2 ”)

105°

90°

635 (25”)

560 (22”)

2120 (83 ½”) +25 (1”)

613 (24 )+25 (1”)

635 (25)

695 (27 )

485 (19 )

1296 (50”)

195 (7 )

8 ()

8 ()

Installation niche features: Free-Standing Series

A

area to be left clear for the anti-tipping brackets

E

area to be left clear for the power supply cable

W

and water supply hose

Minimum Niche Height

2134 mm (84”)

Door Opening Angle

105°

Width

RF396: 886 mm (34 7/8”)
RF376: 736 mm (29”)
WF366: 586 mm (23”)

Minimum Niche Width

RF396: 890 mm (35”)
RF376: 740 mm (29 1/2”)
WF366: 590 mm (23 1/4”)

Door Swing Clearance

RF396: 1470 mm (57 7/8”)
RF376: 1320 mm (52”)
WF366: 1170 mm (46”)

Height

2120 mm (83 1/2”)

Depth with door

635 mm (25 ”)

+ 25 mm (1”)

Important: A 90° door opening

is sufcient to allow opening

and full extraction of the inner
drawers, even if the appliance
is installed directly adjacent to
a wall. Should an opening at
105° be desired, then the ap­pliance should be positioned
at the distance from the wall

described in gure.

7

1

4

1

2

3

Installation Guide

Series: All

Preparing the installation

Transport to installation site

and unpacking

Since this is a large and heavy appliance, before transporting the ap­pliance, check the access to the location where it will be installed
(door size, manoeuvring space in stairwells, etc.).

The appliance is attached to the base of the packaging (pallet) through
four bolts which can be removed using a 17 mm (3/4”) wrench.
It is recommended to use a manual transporting device to move the
appliance to the installation site, and only at this point to remove the
base of the packaging.

The appliance should always be transported in an erect position.
If this is not possible, transport the appliance laying on its rear side.

Once at the installation site, the appliance, which is equipped with four
wheels, can be taken off the pallet and positioned in the installation
area.

Operate as follows:

Take off the four bolts

means of a 17 mm (3/4”) open spanner.

Remove the xing brackets 3 and 4.

To remove the front xing bracket 3 , unscrew for one or two

turns the rear wheel adjusting bolt 2 by means of a 13 mm (1/2”)
box spanner, avoiding too much strenght while thightening the
nut, which could damage the leveling feet adjusting system.

From the back of the unit and by means of a suitable, high duty hand

The appliance is very heavy.
Take maximum care during handling to
avoid injury.

The appliance should always be transport­ed in an erect position.
Avoid at all costs leaning it on its front side.

trolley, take off the appliance and place it on the oor.

Be very careful to avoid any damage to oors. Delicate oors should be

protected with plywood, hard cardboard or similar material panels.

securing the appliance to the pallet by

1

EW

E W

EW

E W

8

E

W

E

W

Series: All

Electrical and Water connection

A Schuko 16 A socket with an efcient grounding should be made

available for the electrical mains connection, as well as an omnipolar
switch which can easily be reached when the appliance is installed.

To connect to the water supply system (for appliances equipped with
ice makers) a tap with a male 3/4” connection should be provided,
which must also be easily accessible once the appliance is installed.
The appliance is provided with a water supply hose and seal kit which
is suitable for high water pressure and complies the Food Regulations.

The water lter cartridge, which is provided with the appliance, should

be installed according to the accompanying instructions.
Use only the new hose and the new gaskets which are supplied with
the appliance. Discard any hose and gasket which may have already
been installed.

Electrical cord length: 2,0 mt (78 3/4”)
Water connection line length: 2,5 mt (98 3/8”)

The Built-in lter cannot make it safe to drink

any water which is not suitable for human
consumption.

The appliance should be connected only to
a drinkable water supply system.

Do not use extension cords or adapters.
Once the appliance has been connected to
the water system, turn the Ice Maker off (touch
the button
before the main water is shut off.

on control panel to switch it off)

Electrical and water supply behind the unit

Integrated and Classic Series StandPlus and Free-Standing Series

Energy: Alternatives and Home Automation

If energy is supplied through an alternative energy power source
(solar, geothermal, etc..) or if home automation systems are installed,
it is necessary to install the Alternative Energy Kit to integrate the unit
into the power grid.

9

Installation Guide

Electrical connection

Water connection

Series: Integrated

Back of appliance

Operate as follows:

1

2

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all
lights are off; should it be not so press the Unit button
off.

Fit one end of the water hose onto the connector at the appli­ance’s back 1.

Fit the other end of the hose to the water tap, use the gaskets pro­vided in the Owner’s Kit 2.

to switch it

10

Series:Free-Standing

Front of appliance

Back of appliance

Water connectionElectrical connection

Operate as follows:

1

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all ights

are off; should it be not so press the Unit button to switch it off.

Connect the water line to the threaded connection at the base of the

unit, as in gure 1.

2

Fit the other end of the hose to the water tap, use the gaskets provided

in the Owner’s Kit 2.

11

1

2

1

2

Installation Guide

Series: All

Levelling

Adjust the appliance level by means of the front levelling feet
and the rear adjustable wheels.

Operate as follows:

After removing the bottom plinth or grille (it is kept in position by
magnets), adjust the height of the levelling feet
mm (3/4”) open spanner.

by means of a 17

1

Then adjust the height of the rear wheels by turning the front
adjusting bolts 2 clockwise or anticlockwise as it may be required.

Remount the bottom plinth or grille.

12

Series: Integrated

Decorative door and bottom-drawer panels layout

The dimensions of the panels are indicated in the table and draw­ings on pages 18-21.

Nevertheless, according to the requirements for aligning with other
kitchen structures, the door panel can be higher than the upper
edge of the refrigerator door, and the drawer panel can be lower
than the edge of the drawer.

The panels must be mounted using special braces which attach
to adjustable devices provided on the door and drawer and with
brackets that anchor and adjust the panel’s vertical direction.

Braces, brackets and fixing screws are provided with the appliance
and must be applied to the panel as indicated.

1

Operate as follows:

To prepare the panels to be mounted on the appliance, follow

2

these steps, working on the back of the panel.

Door Panel

Trace, a line dividing the panel width in half 1.

Starting form the Bottom edge of the panel, mark the positioning

of the brackets 2.

3

Following the corresponding table, mark the external and then

the internal hole

.

3

13

Installation Guide

Series: Integrated

4

Position the brackets on each set of marks to make sure they are
aligned 4, then drill holes through the panel (pay close attention
to the panel’s thickness)5.

Screw the brackets in place 6.

5

Drawer Panel

When preparing the Drawer Panel, follow the same instructions as
per the door panel, but make sure measurements are taken starting
from the top edge 7. The support bracket faces the opposite way

(note imgs 4 and 8).

8

7

8

A

897 (35

)

418 (16

)

418 (16



)

B

C

354.5 (14”)

747 (29

)

343 (13

)

343 (13



)

279.5 (11”)F / G

14

B C

B C

A

F G

13 ()

13 (

)

34 (1

)

34 (1

)

1285 (50 )

1163 (45

)

660 (26”)

157 (6

)

min 1320 (52”)max 635 (25”)

507,5 (20”)

382 (15

)

100 (4”)

Series: Integrated

Decorative panels layout for Fridge with one Bottom-Drawer

Series 90

Series 75

Holes positions

15

H I

D E

A

F G

1286 (50 )

6,5 ()

6,5 (

)

1152,5 (45 )

650,5 (13

)

148,5 (5

)

13 ()

34 (1

)

34 (1

)

min 1320 (52”)

max 635 (25”)

507,5 (20”)

382 (15

)

100 (4”)

60: 327 (12 )

1075 (42 )

min 130 (5 )

115 (4

)

135 (5

)

135 (5

)

A

H

I

F / G

597 (23 ) 597 (23 )

203.5(8”) 203.5(8”)

276.5 (10

)

270.5 (10

)230.5 (9

)

236.5 (9

)

276.5 (10

)

276.5 (10

)268 (10

)

268 (10

)

D

E

Installation Guide

Series: Integrated

Decorative panels layout for Fridge with glass door and one Bottom-Drawer

Series 60

Hinge Left

Hinge Right

Holes positionsDoor window dimensions

16

B

115 (4 )

min 130 (5 )

135

(5 )

135

(5 )

1075 (42 )

2050 (80 )

min 540 (21 )

max 635 (25”)

187 (7 )

A

3 ()

1320 (52”)

Series: Integrated

Panels Dimensions One Bottom - Drawer

Panels with width ranging between 18 mm (3/4 in) and 28 mm (1 1/8 in).
Door panels with weight max of 23 kg (51 lb) and drawer panels with weight max of 11kg (25 lb)

Series

899

749

599

Door/Drawer Width

897 (35 1/4”)

747 (29 3/8”) -

597 (23 3/4”) 327 (12 7/8”)

Door Cutout Width

A

-

B

Examples of calculation

Integration in a kitchen column of total height 2160 mm (85”) and 150 mm (6”) kickplate.

(NOTE: In calculating the adjustment foot is considered to 0).

Drawer Calculation:

Kickplate 187 - 150 = 37 mm (1 1/2”)

Upper Panel Calculation:

2160 - 2050 = 110 mm (4 3/8”)

Total Height Calculation:

150 + 577 + 3 + 1430 = 2160 mm (85”)

540 + 37 = 577 mm (22 3/4”)

1320 + 110 = 1430 mm (56 1/4”)

17

Installation Guide

Series: Integrated

Mounting panels to the door and the drawer

Once all brackets and small brackets have been applied to the pan­els, you can begin installing the bottom drawer.

1

Operate as follows:

2

Partially tighten the screw to the xing 1.

Hook the bottom drawer panel starting from the xings on the bot-

tom 2.

3

It is now possible to align panels to adjacent cabinets in height
using the lower alignment brackets, 3 tightening or untightening
the screws into position as needed. With the screw slighty tightened,
move the panel sideways to align it to the other panels on the unit or
other adjacent structures.

Depth alignment: working from the inside of the drawer, after lift­ing up the magnetic seal, adjust the panel position so it is closer to or
further away from the door using the holes
panel using the holes

.

5

and then secure the

4

4

5

Once the front panel has been adjusted,
check that the gasket has been
repositioned correctly to assure the
door/drawer are closing correctly and
avoid operational errors of the unit.

18

Series: Integrated

Hook the panel to the fixing devices starting from the top aligning

6

bracket 6.

7

8

At this point, alignment between the panel and adjacent cabi­nets can be adjusted using the alignment bracket and small brack­ets 7 and 8.

Vertical alignment: tighten or loosen the screw in the brackets to
raise or lower the panel 9.

9

Depth alignment: working from the inside of the door, after lift­ing up the magnetic seal, adjust the panel position so it is closer to
or further away from the door using the holes 10 and then fix the
panel in position using the holes 11.

10

11

Once the front panel has been adjusted,
check that the gasket has been
repositioned correctly to assure the
door/drawer are closing correctly and
avoid operational errors of the unit.

19

B

A

6,5 () 6,5 ()

20 ()

20 ()

22 ()

22 ()

22 () 22 ()

Installation Guide

Series: Integrated

Installation

Built-in installation single appliance

For a built-in installation, to close gaps between the appliance and

the adjacent cabinets, special side proles and aluminum covering

frames are provided.

1

Operate as follows:

Push the appliance into the installation niche 1.

2

If the unit is to be installed inside a niche or within an enclosed
structure, it is necessary to design a ventilation shaft at the back of
the niche to assure proper ventilation at the back of the unit. A 5 mm

gap is sufcient to prevent overheating. Always mount front panels on
door and drawer before pushing the unit into its nal position inside the

niche or structure.

Secure the appliance to the adjacent cabinets by xing to these the
side proles previously mounted on the appliance 2.

To make this operation easier keep the door and the drawer open.

3

Wall

or

furniture

Check the levelling of the appliance, adjusting its feet and wheels
to correct it.

Mount the proles the covering frames: rst insert them laterally and
then push rmly until a “click” is heard 3.

Side proles mounting

Appliance Wall

or

furniture

A Connecting element B Alluminium frame

20

Series: Integrated

Built-in installation two or more appliances

1

2

Required accessories to be ordered separately:

Central connection Kit

Special side proles and aluminum covering frames are provided for

closing gaps between the appliance and the adjacent cabinets.

Operate as follows:

Position the appliances in front of the installation area, leaving
enugh space to operate at their back 1.

Move at the back of the appliances to mount the joining brackets:

x on side of the top and lower brackets to one of the appliances

and subsequently to the other 2.

3

4

Place the two units side by side and join them at the front attaching

the two pro les with the supplied screws 3.
Attach the bracket on top of the units as per  gure 4.

5

Finish off by mounting the central cover frame onto the central

profiles, by pushing it until a click is heard 5.

21

E

D

A

B

A

B

D

6,5 () 6,5 ()

20 ()

20 ()

22 ()

22 ()

22 () 22 ()

6,5 ()6,5 ()

18 ()

44,4 (1 )

18 ()

C

13 ()

Installation Guide

Series: Integrated

6

Once completed the previous steps, push the units in their nal posi­tion 6.
If the units are to be installed inside a niche or within an enclosed
structure, it is necessary to design a ventilation shaft at the back of
the niche to assure proper ventilation at the back of the unit. A 5 mm

gap is sufcient to prevent overheating. Always mount front panels on
door and drawer before pushing the unit into its nal position inside the

niche or structure.

Check the levelling of the appliance, adjusting its feet and wheels
to correct it.

Secure the appliance to the adjacent cabinets by xing to these the
side proles previously mounted on the appliance 7.

To make this operation easier keep the door and the drawer open.

7

8

Mount the covering frames onto the proles, rst insert them laterally
and then push rmly until a “click” is heard 8.

Side and central proles mounting

Wall

or

Appliance Appliance

furniture

Wall

or

furniture

A Connecting element
B Alluminium frame

D Connecting element
E Aluminium frame

22

Series: Integrated

Free-standing installation

two or more appliances

Operate as follows:

Position the appliances in front of the installation area, leaving
enough space to operate at their back.

1

Move at the back of the appliances to mount the joining prole

Place the two units side by side and join them at the front attach the

bracket on top of the units as per gure

and at the bottom

2

1

.

3

2

Check the levelling of the appliance, adjusting its feet and wheels
to correct it.

3

23

2 x

152 (6”)

59 (

2



”)

45 (1



”)

Installation Guide

Series: Integrated

Anti-tipping safety assembly

To prevent the appliance from tipping over an extra-long kit is vailable
up on request if the appliance needs to remain distanced from the
wall, it is mandatory to install two brackets on the upper part of the

appliance for xing it securely to the wall.

1

Operate as follows:

The brackets should be applied as illustrated using the provided
screws and expansion plugs.
Place a bracket on the top of the appliance in correspondence to the

xing holes and against the wall

.

1

2

Mark up the holes position on the wall 2.

3

Drill the wall with an 8 mm (3/8”) bit and insert the expansion plug

.

3

4

Reposition the bracket and x it rst to the cabinet and then to the

wall

To avoid danger of the appliance tipping over
it is mandatory to secure the appliance to the
wall by means of two special brackets.

.

4

24

Series:Free-Standing

Anti-tipping safety assembly

To avoid danger of the appliance tipping over when opening full doors
and drawers, it is mandatory to install two brackets on the upper part

of the appliance for xing it securely to the wall.

The brackets should be applied as illustrated using the provided screws
and expansion plugs.

1

Operate as follows:

Place a bracket on the top of the appliance in correspondence to

the xing holes and against the wall 1.

2

Mark up the holes position on the wall 2.

3

Drill the wall with an 8 mm (3/8”) bit and insert the expansion plug

3

.

To avoid danger of the appliance tipping over
it is mandatory to secure the appliance to the
wall by means of two special brackets.

Reposition the bracket and x it rst to the cabinet and then to the

wall

.

4

25

E

W

Installation Guide

Series:Free-Standing

Anti-tipping safety assembly: full integration

3

1

Fit the brackets and secure them to the wall 1, remove the ventila-

tion grid

and the frontal closing 3.

2

2

Make the electrical and water connection 4 (see page 8) and push

the unit

Insert the brackets to the rear holes 6.

.

5

5

6

Fix brackets and reinstall the removed parts 7.

4

7

26

Series: Free-Standing

Mounting the handles on stainless front

1

To mount the handles onto the door and the drawer operate as follows:

Operate as follows:

Insert the two handle spacers onto the supports already available on
the door and the drawer 1.

Screw in the Allen screws available on the handle 2.

2

The screws must be tightened in by means of a 2.5 mm (1/8”) hex
wrench.

27

A

B

C

C

A 860 (33 ) 740 (29 )560 (22”)

> 100 (4”)

10 ()

50%

B

C

Installation Guide

Series: Integrated

Ventilation

A forced air system assures ventilation through a grille positioned
in the lower front part of the unit. If the kitchen design includes a
kickplate, the latter has to be punched in order to maintain a sati-

sfactory air ow, as described in the drawing. Holes can be in any

shape and size, as long as the total area of the punched part equals
50% of the kickplate are.

In this case, to guarantee a better air ow, it is advisable to remove

the front grille included with the unit. The grille is secured to the unit
with magnetic plates and can be easily removed even by the end
user, to provide for regular cleaning procedures and remove dust.
If the grille is partially covered by the kitchen kickplate, it is advisable

to remove the grille in order to provide for a better airow.

899 Series 749 Series 599 Series

28

Series:Free-Standing

Ventilation

Ventilation is insured by a forced air system through a grille located in
the upper part of the appliance.

This grille should never be covered by panels or any other devices that

could reduce its efciency.

Please refer to page 5-6 to ensure correct air circulation.

29

Installation Guide

Series: All

Post installation control

Check that the front levelling feet have been properly installed.

Check that the connection to the water system does not have any

leaks and that the closing tap is easily accessible.

Check that the electrical connection is correctly installed and that

the multipole switch and socket are easily accessible.

Check the perfect alignment of the appliance with adjacent

structures.

Check that all adhesive tape and external or internal temporary

protective devices have been removed.

Check the perfect closing of the doors and the smooth sliding of

the drawers and shelves.

30

9

4

4.1

Accensione e spegnimento dell’apparecchiatura

Se alla prima accensione non appare la scritta
Stand-by, ma appaiono altre scritte, significa che
l’apparecchiatura ha già iniziato la procedura di
raffreddamento.

Durante la prima accens ione non sa rà po ssibi le u ti­lizzare il menù Me nu per un ’even tual e m odifi ca delle
preimpostaz ioni di fabbri ca fino al raggi ungim ento
della tempe ratur a pr eimpo stat a. È p ossib ile tu ttav ia re­golare da sub ito l’or a e la dat a, param etri co munqu e
necessari p er a ttiv are a lcun e fun zion i sp ecial i.

Ad ogni accensione l’apparecchiatura esegue una
procedura di autodiagnosi della durata di 3 minuti pri­ma di avviarsi completamente.

Se si spegne solo il vano Frigorifero, il relativo ven­tilatore continua a funzionare autonomamente per
prevenire la possibile formazione di odori e muffe.

Prima di spegnere per un periodo lungo l’intera ap­parecchiatura, rimuovere tutti gli alimenti conservati
e lasciare le porte ed i cassetti aperti per evitare il
formarsi di cattivi odori e muffe.

Quando l’apparecchiatura è collegata alla rete elettrica ma non è
stata ancora accesa viene visualizzato sul display il messaggio

Per accendere tutti i vani dell’apparecchiatura agire per 3 secondi
sul tasto Unit .
Alla prima accensione il vano Multizone è predisposto nella funzio­nalità Freezer.

Prima accensione

Dopo la prima accensione si raccomanda di attendere almeno 12
ore, senza aprire le porte, prima di introdurre alimenti nell’apparec­chiatura. Durante tale periodo disattivare eventuali messaggi sonori
sfiorando il tasto Alarm

.

Può essere spento solo attraverso lo spegnimento completo dell’ap­parecchiatura.
Agire per 3 secondi sul tasto Unit

.

Durante periodi di assenza molto lunghi è consigliabile spegnere il
frigorifero agendo sul tasto Unit

per 3 secondi e staccando la spi-

na o agendo sull’interruttore omnipolare che lo alimenta.

Svuotarlo di tutto il suo contenuto, pulirlo ed asciugarlo e lasciare le
porte ed i cassetti parzialmente aperti per evitare la formazione di
cattivi odori.

Spegnimento vani Frigorifero

Spegnimento vano Multizone

Riaccensione

Spegnimento per lunghi periodi

Accensione e spegnimento

Agire nuovamente sugli stessi tasti per la riaccensione.
Il vano Freezer rimane sempre acceso e non può essere spento se
non attraverso lo spegnimento completo dell’apparecchiatura.
Agire per 3 secondi sul tasto Unit

.

3

3.3

3.3

Componenti principali

Componenti principali

3.5

3.4

123456798

1

Unit

2

Fridge

3

Menu

4

Up/down
Fridge

5

Display

6

Up/Down
Freezer
(Multizone)

7

Enter

8

Ice maker

9

Alarm

8

Il sistema di controllo elettronico mantiene costante la temperatura dei due vani e la visualizza sul display del pannello di con­trollo; consente inoltre l’interazione dell’utente con il sistema di controllo, tramite l’impostazione personalizzata delle diverse
funzioni e l’invio di messaggi sonori e/o visivi, qualora si verificassero anomalie nel funzionamento dell’apparecchiatura.

Pannello di controllo principale

Controllo elettronico

Permette lo spegnimento completo e l’accensione dell’apparecchia­tura (agire su di esso per 3 secondi).

Permette lo spegnimento e l’accensione del solo vano frigorifero (agire
su di esso per 3 secondi).

Permette l’accesso al menù delle funzioni dell’apparecchiatura

Visualizza le temperature dei vani frigorifero e freezer, la data e l’ora, le
funzioni Menu ed i messaggi visivi.

Tramite lo sfioramento dei tasti Up/Down è possibile variare la tempe­ratura preimpostata a seconda delle scelte di utilizzo del vano (free­zer, frigorifero o 0°C).

Permette di confermare l’attivazione o la disattivazione delle selezioni
operate attraverso Menu.

Permette di attivare o disattivare la produzione automatica di ghiaccio.

Lampeggia per segnalare eventuali anomalie di funzionamento, evi­denziate anche attraverso un avviso sonoro, disattivabile attraverso lo
sfioramento del tasto.

Tramite lo sfioramento dei tasti Up (su) e Down (giù) è possibile variare
la temperatura già impostata per il frigorifero e muoversi all’interno
del menù interattivo.

Prima di iniziare

Series: All

Start up

To start the appliance, connect the plug to the electrical mains: at
this point, when opening the door, the control panel will usually visual-

ize the message “Stand by”, and all the panel keys be off

To turn on all the appliance compartments, press the Unit button

for three seconds. The display will show the message “Initial test” for

approx. 2 minutes. After this phase the compressors will start up and re­main on until the default temperature set up in the factory is reached.
Do bear in mind that this condition could last several hours.
If the appliance is provided with an Ice Maker, prior to switching it

on make sure that the water lter cartridge is installed, then ll the

water system. To this purpose switch off the Ice Makerand performe a
manual clean procedure.
At the end switch the Ice Maker on again by touching the

button.

For further information about the appliance operation, refer to the
User Manual.

If at the rst start - up the message Stand by does

not appear, but other messages appear, such
as Fridge too warm, Fresco too warm, Freezer
too warm, or sound signals are activated, it
means that the appliance has already started
the cooling process.
If this is the case, deactivate any possible acous­tic signals by pressing the Alarm button, close
the door and wait until the set temperature is
reached.

It is necessary to let the unit reach the correct
temperature before foods are stored inside.

Installation Guide

22-122014

GI-SMEG EN