e
PRECAUTIONS 31
General safety instructions 31
Installation 35
Appliance purpose 36
This user manual 36
Manufacturer’s liability 36
Identification plate 36
Disposal 37
Information for European Control Bodies 37
Energy efficiency technical data 37
To save energy 37
Light sources 37
How to read the user manual 37
DESCRIPTION 38
General description 38
Hob 39
Control panel 39
Other parts 40
Accessories 40
USE 41
Preliminary operations 41
Using the accessories 41
We advise you to read this manual carefully, which contains all the instructions for maintaining the
appliance’s aesthetic and functional qualities. For further information on the product: www.smeg.com
Using the hob 41
Using the storage compartment (where present)
44
Using the oven 44
Digital programmer 45
Cooking advice 46
Cooking information table (multifunction oven) 47
Cooking information table (auxiliary oven) 48
CLEANING AND MAINTENANCE 49
Cleaning the appliance 49
Cleaning the glass ceramic hob 49
Knobs 50
Cleaning the door 50
Cleaning the oven cavity 51
Cleaning the roof of the oven (only for some
models/cavities) 52
Vapor Clean (on some models only) 53
Extraordinary maintenance 53
INSTALLATION 54
Positioning 54
Electrical connection 56
Instructions for the installer 56
PRECAUTIONS
General safety instructions
Risk of personal injury
• During use the appliance and
its accessible parts become
very hot. Keep children well
away from the appliance.
• The appliance becomes very
hot during use. Make sure that
you never touch the heating
elements inside the oven.
• Protect your hands by wearing
oven gloves when moving food
inside the oven.
• Never try to put out a fire or
flames with water: Turn off the
appliance and smother the
flames with a fire blanket or
other appropriate cover.
• This appliance may only be
used by children aged 8 years
and over, and by people of
reduced physical, sensory or
mental capacity, or lacking in
experience in the use of
electrical appliances, provided
that they are supervised or
have been given instructions on
the safe use of the appliance
and of the hazards associated
with it.
• Children must not play with the
PRECAUTIONS - 3191477A166/C
appliance.
• Keep children under the age of
eight at a safe distance unless
they are constantly supervised.
• Keep children under the age of
8 away from the appliance
when it is in use.
• Cleaning and maintenance
must not be carried out by
unsupervised children.
• Be aware of how rapidly the
cooking zones heat up. Do not
place empty pans on the heat.
Danger of overheating.
• After use the cooking zones
remain hot for a certain period
of time after they have been
turned off. Do not touch the hob
surfaces.
• The cooking process must
always kept under control. A
short cooking process must be
continuously monitored.
• WARNING: Leaving food that
contains fat and/ oil
unattended when cooking can
be dangerous and can cause a
fire. DO NOT attempt to
extinguish a fire with water. Turn
off the appliance and smother
the flames, for example with a
lid or a blanket.
• Do not use the Booster and/or
the Double Booster functions (if
present) to heat fats or oils. Fire
hazard.
• Do not place metal objects,
such as dishes or cutlery, on the
surface of the hob during
cooking as they may overheat.
• Do not cook foods in closed
tins or containers or plastic
containers.
• Do not insert pointed metal
objects (cutlery or utensils) into
the slots in the appliance.
• Do not use or store flammable
materials near the appliance.
• Do not pour water directly onto
very hot trays.
• Keep the oven door closed
during cooking.
• If you need to move food or at
the end of cooking, open the
door 5 cm for a few seconds,
let the steam come out, then
open it fully.
• Do not open the storage
compartment (where available)
when the oven is on and still
hot.
• The items inside the storage
compartment (where available)
could be very hot after the oven
has been used.
• Switch off the appliance
immediately after use.
• Do not pull the cable to unplug
the appliance (if present).
• DO NOT USE OR STORE
FLAMMABLE MATERIALS IN
THE STORAGE
COMPARTMENT (IF
AVAILABLE) OR NEAR THE
APPLIANCE.
•DO NOT USE AEROSOLS IN
THE VICINITY OF THIS
APPLIANCE WHILST IT IS IN
32 - PRECAUTIONS 91477A166/C
e
USE.
• DO NOT MODIFY THIS
APPLIANCE.
• Always wear personal
protective equipment (PPE)
before carrying out any work
on the appliance (installation,
maintenance, positioning or
moving).
• Do not clean the appliance if it
is still hot or in operation.
• Before performing any work on
the appliance, switch off the
power supply.
• WARNING: Make sure that
the appliance has been
switched off and disconnected
from the mains power supply or
that the mains power has been
switched off before replacing
the interior lighting bulbs.
• The bulbs used in this
appliance are specific for
household appliances; do not
use them for home lighting.
• Do not try to repair the
appliance yourself or without
the assistance of a qualified
technician.
• If the power cable becomes
damaged, contact technical
support immediately to arrange
for it to be replaced in order to
avoid possible hazards.
• If cracks or fissures form, or if
the glass ceramic cooking
surface breaks, turn off the
appliance immediately.
Disconnect the power supply
and call Technical Support.
• Do not touch or clean the hob
surface during operation or
when the residual heat
indicator lights are still on.
• Activate the controls lock when
you have children or pets that
could reach the hob.
• After use, switch off the plates.
Never rely solely on the
cookware detector.
• Supervise children carefully as
they cannot readily see the
residual heat indication. After
use the cooking zones remain
hot for a certain period of time
even if they have been turned
off. Keep children away from
the cooking zones.
• People who have pacemakers
or other similar devices fitted
must make sure that the
operation of these devices is
not affected by the induction
field, the frequency range of
which is between 20 and 50
kHz.
• In conformity with the provisions
regarding electromagnetic
compatibility, the
electromagnetic induction
cooking hob comes under
group 2 and class B (EN
55011).
Risk of damaging the appliance
• Do not use harsh or abrasive
detergents or sharp metal
scrapers to clean the glass
PRECAUTIONS - 3391477A166/C
door of the oven since they
may scratch the surface and
cause the glass to shatter.
• Use wooden or plastic utensils.
• Do not use steam jets to clean
the appliance.
• Do not use the appliance as a
support surface.
• Do not obstruct ventilation
openings and heat dispersal
slots.
• Do not sit on the appliance.
• Do not rest any weight or sit on
the open door of the
appliance.
• Racks and trays should be
inserted as far as they will go
into the side guides. The
mechanical safety locks that
prevent them from being
removed must face downwards
and towards the back of the
oven.
• Never leave the appliance
unattended during cooking
operations that could lead to
oils and fats overheating and
catching fire. Be very careful
• Risk of fire: Do not store objects
on the cooking surfaces.
• Do not spray any spray
products near the oven.
• DO NOT FOR ANY REASON
USE THE APPLIANCE AS A
SPACE HEATER.
• Do not use plastic kitchenware
or containers for cooking.
• Do not put sealed tins or
containers in the oven.
• Remove all trays and racks
which are not required during
cooking.
• Do not cover the bottom of the
oven cavity with aluminium or
tin foil sheets.
• Do not place pans or trays
directly on the bottom of the
oven cavity.
• If necessary, you can use the
tray rack (supplied or sold
separately, depending on the
model) by placing it on the
bottom as a support for
cooking.
• If you wish to use greaseproof
paper, place it so that it will not
interfere with the hot air
circulation inside the oven.
• Do not use the open door to
rest pans or trays on the internal
glass pane.
• Cooking vessels or griddle
plates should be placed inside
the perimeter of the hob.
• All pans must have smooth, flat
bottoms.
• If any liquid does boil over or
spill, remove the excess from
the hob.
• Take care not to spill acid
substances such as lemon juice
or vinegar on the hob.
• Do not spill sugar or sweet
34 - PRECAUTIONS 91477A166/C
e
mixtures on the hob during
cooking.
• Do not place materials or
substances that could melt or
catch fire (paper, plastic or
aluminium foil) on the
appliance while it is in use.
• Do not use steam jets to clean
the appliance.
• Place the cookware directly on
the glass ceramic surface.
• Do not put empty pans or frying
pans on switched on cooking
zones.
• Do not use rough or abrasive
materials or sharp metal
scrapers.
• Do not use cleaning products
containing chlorine, ammonia
or bleach on parts made of
steel or that have metallic
surface finishes (e.g. anodizing,
nickel- or chromium-plating).
• Do not use abrasive or
corrosive detergents (e.g.
scouring powders, stain
removers and metallic
sponges) on glass parts.
• The glass ceramic surface is
highly resistant to impacts.
However, avoid hard, solid
objects falling on the cooking
surface as they may cause it to
break.
• Never use the oven door to
lever the appliance into place
when fitting.
• Avoid exerting too much
pressure on the door when
open.
• Take care that no objects are
stuck in the doors.
• Do not use the handle to lift or
move this appliance.
Installation
• THIS APPLIANCE MUST NOT
BE INSTALLED IN BOATS OR
CARAVANS.
• This appliance must not be
installed on a pedestal.
• Always use any necessary/
required personal protective
equipment (PPE) before
performing any work on the
appliance (installation,
maintenance, positioning or
movement).
• Position the appliance into the
cabinet cut-out with the help of
a second person.
• Check that the carcase has the
required openings.
• Check that the carcase material
is heat resistant.
• To avoid potential overheating,
the appliance must not be
installed behind a decorative
door or a panel.
• Installation and servicing should
be carried out by qualified
personnel in accordance with
current standards.
• Have the electrical connection
performed by authorised
technical personnel.
• The appliance must be
connected to earth in
compliance with electrical
PRECAUTIONS - 3591477A166/C
system safety standards.
• Use cables that can withstand
temperatures of at least 90°C.
• The tightening torque of the
screws of the terminal supply
wires must be 1.5 - 2 Nm.
• Be careful when connecting
additional electrical
appliances. Connection cables
must not come into contact with
hot cooking zones.
• The power cable must only be
installed or replaced by a
qualified technician.
• If the power cable becomes
damaged, contact technical
support immediately to arrange
for it to be replaced in order to
avoid possible hazards.
• Allow the appliance to be
disconnected after installation,
via an accessible plug or a
switch in the case of a fixed
connection.
• Fit the power line with an allpole circuit breaker with a
contact separation distance
sufficient to provide complete
disconnection in category III
overvoltage conditions,
pursuant to installation
regulations.
• This appliance can be used up
to a maximum altitude of 2,000
metres above sea level.
For this appliance
• The swing doors are not held in
place when open and may
tend to close again. During use,
pay attention not to come into
contact with the internal glass
pane to prevent burns.
Appliance purpose
This appliance is intended for
cooking food in the home
environment. Every other use is
considered inappropriate. It
cannot be used:
• in employee kitchens, shops,
offices and other working
environments.
• in farms/farmhouses.
• by guests in hotels, motels and
residential environments.
• In bed and breakfast
accommodation.
This user manual
• This user manual is an integral part of the
appliance and must therefore be kept in its
entirety and within the user's reach for the
whole working life of the appliance.
• Read this user manual carefully before using
the appliance.
• The explanations in this manual include
images, which describe all that regularly
appears on the display. However, it should
be kept in mind that the appliance may be
equipped with an updated version of the
system, and as such, all that appears on the
display may differ from those in the manual.
Manufacturer’s liability
The manufacturer declines all liability for
damage to persons or property caused by:
• use of the appliance other than that
specified;
• failure to comply with the instructions in the
user manual;
• tampering with any part of the appliance;
• use of non-original spare parts.
Identification plate
The identification plate bears the technical data,
serial number and brand name of the
36 - PRECAUTIONS 91477A166/C
e
appliance. Do not remove the identification
plate for any reason.
Disposal
This appliance conforms to the WEEE
European directive (2012/19/EU) and
must be disposed of separately from
other waste at the end of its service life.
The appliance does not contain substances in
quantities sufficient to be considered hazardous
to health and the environment, in accordance
with current European directives.
Power voltage
Danger of electrocution
• Disconnect the mains power supply.
• Unplug the appliance.
To dispose of the appliance:
• Cut the power cable and remove it.
• Deliver the appliance to the appropriate
recycling centre for electrical and electronic
equipment waste, or return it to the retailer
when purchasing an equivalent product, on
a one for one basis.
Our appliances are packaged in non-polluting
and recyclable materials.
• Deliver the packing materials to the
appropriate recycling centre.
Plastic packaging
Danger of suffocation
• Do not leave the packaging or any part of it
unattended.
• Do not let children play with the plastic
bags.
Information for European Control
Bodies
Fan forced mode
the ECO function used to define the energy
efficiency class complies with the specifications
of European standard EN 60350-1.
Energy efficiency technical data
Information in accordance with the European
energy labelling and ecodesign regulations is
contained in a separate document
accompanying the product instructions.
These data are present in the "Product
information sheet" that can be downloaded
from the website at the page dedicated to the
product in question.
To save energy
• Only preheat the appliance if the recipe
requires you to do so.
• Unless otherwise indicated on the package,
defrost frozen foods before placing them in
the oven.
• When cooking several types of food it is
recommended to cook the foods one after
the other to make the best use of the already
hot oven.
• Use dark metal moulds: They help to absorb
the heat better.
• Remove all trays and racks which are not
required during cooking.
• Stop cooking a few minutes before the time
normally used. Cooking will continue for the
remaining minutes with the heat which has
accumulated inside the oven.
• Reduce any opening of the door to a
minimum to avoid heat dispersal.
• Keep the inside of the oven clean at all
times.
Light sources
• This appliance contains user-replaceable
light sources.
• The light sources contained in the appliance
are declared suitable for operation at
ambient temperature ≥300°C and intended
for use in high temperature applications such
as ovens.
• This appliance contains light sources of
efficiency class "G".
How to read the user manual
This user manual uses the following reading
conventions:
Warning/Caution
Information/Advice
PRECAUTIONS - 3791477A166/C
DESCRIPTION
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
2
1
2
1
8
3
12
1
2
11
5
6
8
13
9
7
4
10
General description
1 Hob
2 Control panel
3 Auxiliary oven seal
4 Auxiliary oven light
5 Auxiliary oven door
6 Multifunction oven door
7 Left multifunction oven light
8 Fan
9 Left multifunction oven seal
10 Right multifunction oven light
11 Storage compartment
12 Right multifunction oven door
13 Right multifunction oven seal
Frame shelf
38 - DESCRIPTION 91477A166/C
e
Hob
2
1
4
5
3
2
5
7
8
4
3 10
1
6 9
Zone
* power levels are indicative and can vary according to the pan used or the settings made.
Outer diameter
(mm)
1 210 120 210 2300 3000
2 180 110 180 1300 1400
3 270 145 270 2300 3000
4 180 110 180 1300 1400
5 210 120 210 2300 3000
Pan Ø
min. (mm)
Pan Ø
recommended
(mm)
Max. power draw
(W)*
Power draw in
booster function
(W) *
Control panel
1 Hob cooking zone knobs
Useful for controlling the cooking zones of the
induction hob. Press and turn the knobs
clockwise to adjust the operating power of the
hot plate from a minimum of 1 to a maximum of
9. The working power is indicated on the
display on the hob.
2 Programmer clock
For displaying the current time, setting
programmed cooking operations and the
minute minder timer.
The programmer clock only controls the
upper multifunction oven.
3 Auxiliary oven variable grill knob
It turns on the light inside the oven or starts the
grill heating element to a temperature ranging
from a minimum of 50°C to a maximum of
245°C.
4 Auxiliary oven variable grill indicator light
The indicator light comes on to indicate that the
auxiliary oven is heating up. It turns off as soon
DESCRIPTION - 3991477A166/C
as it reaches the set temperature. It flashes
regularly to indicate that the temperature set
inside the oven is kept constant.
5 Left multifunction oven left temperature
knob
This knob allows you to select the cooking
temperature and the Vapor Clean temperature.
Turn the knob clockwise to the required value,
between the minimum and maximum setting.
6 Left multifunction oven indicator light
The indicator light comes on to indicate that the
oven is heating up. It turns off as soon as it
reaches the set temperature. It flashes regularly
to indicate that the temperature set inside the
oven is kept constant.
7 Left multifunction oven left functions knob
The oven’s various functions are suitable for
different cooking modes. After selecting the
required function, set the cooking temperature
using the temperature knob.
8 Upper multifunction oven indicator light
The indicator light comes on to indicate that the
oven is heating up. It turns off as soon as it
reaches the set temperature. It flashes regularly
to indicate that the temperature set inside the
oven is kept constant.
9 Upper multifunction oven temperature
knob
This knob allows you to select the cooking
temperature and the Vapor Clean temperature.
Turn the knob clockwise to the required value,
between the minimum and maximum setting.
10 Upper multifunction oven functions knob
This knob allows you to select the cooking
temperature and the Vapor Clean temperature.
Turn the knob clockwise to the required value,
between the minimum and maximum setting.
Other parts
Shelves
The appliance features shelves to position trays
and racks at different heights. The insertion
heights are indicated from the bottom upwards
(see General description).
Cooling fan
The fan cools the oven and comes into
operation during cooking. The fan causes a
steady outflow of air that exits from the rear of
the appliance and which may continue for a
brief period of time even after the appliance has
been turned off.
Do not obstruct ventilation openings
and heat dispersal slots.
Interior lighting
The appliance’s interior lighting comes on:
• Multifunction oven: when any function is
selected, apart from the function.
• Auxiliary oven: when the variable grill knob
is turned to the symbol or to the cooking
temperature.
Accessories
• Not all accessories are available on some
models.
• The accessories intended to come into
contact with food are made of materials that
comply with the provisions of current
legislation.
• Original supplied and optional accessories
can be requested to Authorised Assistance
Centres. Use only original accessories
supplied by the manufacturer.
Deep tray
Useful for collecting fat from foods placed on
the rack above and for cooking pies, pizzas,
baked desserts, biscuits, etc.
Tray rack
To be placed over the top of the tray; for
cooking foods which may drip.
40 - DESCRIPTION 91477A166/C
e
Rack
Useful for supporting containers with food
USE
during cooking.
Preliminary operations
See General safety instructions.
• Remove any protective film from the outside
or inside of the appliance, including
accessories.
• Remove any labels (apart from the technical
data plate) from the accessories and
shelves.
• Remove and wash all the appliance
accessories (see chapter "CLEANING
AND MAINTENANCE").
First heating
1. Set a cooking time of at least one hour (see
paragraph "Using the oven").
2. Heat the empty oven compartment at the
maximum temperature to burn off any
residues left by the manufacturing process.
When heating the appliance
• air the room;
•don't stay.
Carry out a first pre-heating cycle for
each of the cavities in the appliance.
Using the accessories
Racks and trays
Racks and trays have to be inserted into the side
guides until they come to a complete stop.
• The mechanical safety locks that prevent the
rack from being removed accidentally must
face downwards and towards the back of
the oven cavity.
Gently insert racks and trays into the
oven until they come to a stop.
Clean the trays before using them for
the first time to remove any residues left
by the manufacturing process.
Tray rack
The tray rack has to be inserted into the tray. In
this way fat can be collected separately from
the food which is being cooked.
Using the hob
All the appliance’s control and monitoring
devices are located together on the front panel.
The relevant cooking zone is indicated next to
each knob. Just turn the knob clockwise to the
required power setting.
On first connection to the electrical
mains, an automatic check will be
carried out that will switch on all
indicator lights for a few seconds.
USE - 4191477A166/C
After use, turn off the hot plates that
were used by moving the relative knob
back to position 0. Never rely solely on
the cookware detector.
Cookware suitable for use in induction
cooking
Cookware used on the induction cooking
surface must be made of metal, with magnetic
properties and a sufficiently large base.
Suitable cookware:
• Enamelled steel cookware with thick bases.
• Cast iron cookware with an enamelled
base.
• Cookware in multilayer stainless steel, ferritic
stainless steel and aluminium with a special
base.
Unsuitable cookware:
• Copper, stainless steel, aluminium, fireproof
glass, wood, ceramic and terracotta
cookware.
To see whether the pan is suitable, bring a
magnet close to the bottom: if it is attracted, the
pan is suitable for induction cooking. If you do
not have a magnet, you can put a small amount
of water in the pan, place it on a cooking zone
and start the hot plate. If the symbol
appears on the display, it means the pan is not
suitable.
Use only cookware with a perfectly flat
bottom which is suitable for induction
hot plates. Using cookware with an
irregular bottom could jeopardise the
efficiency of the heating system and
prevent cookware from being detected
on the hot plate.
Cookware recognition
When there is no saucepan on a cooking zone
or if the saucepan is too small, no energy will be
transmitted and the symbol will appear on
the display. If there is a suitable saucepan on
the cooking zone, the recognition system
detects it and switches on the hob to the power
level set using the knob. Energy transmission is
also interrupted when the saucepan is removed
from the cooking zone (the symbol will be
shown on the display). If the cookware
recognition function is activated in spite of the
saucepan or frying pan on the cooking zone
being smaller than the zone itself, only the
necessary energy will be transmitted.
Saucepan recognition limits
The minimum diameter of the pan base is
indicated by the cross on the cooking zone.
Pans with smaller diameters risk not being
detected and therefore not activating the
inductor.
Limiting the cooking duration
The hob has an automatic device which limits
the duration of use. If the cooking zone settings
are not changed, the maximum duration of
operation for each zone depends on the power
level selected. When the device for limiting the
duration of use is activated, the cooking zone
turns off, a short alert sounds and, if the zone is
hot, the symbol appears on the display.
Set power level
18
26
3 - 4 5
54
6 - 7 - 8 - 9 1.5
Maximum cooking duration in
hours
Protection from overheating
If the hob is used on full power for a long
period, the electronics will have trouble cooling
down if the room temperature is high. To avoid
excessively high temperatures forming in the
electronics, the power to the cooking zone is
reduced automatically.
Residual heat
If the cooking zone is still hot after being
switched off, the symbol will be displayed
on the display. The symbol clears once the
temperature drops below 60°C.
42 - USE 91477A166/C
e
Heating accelerator
Each cooking zone is equipped with a
heating accelerator that allows the
maximum power to be delivered for a
time that is proportional to the selected
power.
This function allows the selected power to be
achieved in the shortest amount of time.
1. Turn the knob anticlockwise to position A
and then release it. The display shows the
symbol.
2. Select the required heating power (1..8)
within 3 seconds. The selected power and
the symbol will flash alternately on the
display.
The power level can be increased at any
moment. The “maximum power” period will
automatically be modified. Once the
acceleration period is over the power level will
remain the same as the one previously selected.
If the power is reduced, by turning the
knob anti-clockwise, the heating
accelerator will automatically be
disabled.
Keep warm
The Keep warm function allows you to
keep cooked food warm.
To activate the Keep Warm function turn the
knob of the required zone to an intermediate
position between 0 (off) and power level 1, until
the symbol appears on the corresponding
display.
Booster function
The booster function allows the cooking zone to
be activated at maximum power for as long as
5 minutes. It can be used to bring a large
quantity of water to a boil rapidly or to broil
meat.
• To activate the Booster function, turn the
knob clockwise to position P, keep it there
until the symbol appears on the
corresponding display and then release the
knob.
• After 5 minutes of continuous operation, the
Booster function will be disabled
automatically and cooking will continue at
power level 9.
• Select any other power level to deactivate
the Booster function.
Only for some zones: the Booster function is
always enabled and has to be disabled
manually using the corresponding knob.
The Booster function has priority over
the heating Accelerator function.
wHob power limitation
The induction hob is configured to operate at
7.4 kW, but it can be set to operate at 4.8 kW
or 3.7 kW.
1. Disconnect the appliance from the mains
power supply and wait 10 seconds before
turning the power back on.
The hob power limitation must be set
within 2 minutes of it being connected to
the mains power supply.
2. Turn both the front left and front right
cooking zone knobs anticlockwise to
position “A” at the same time, and keep
them in this position for 3 seconds.
The rear left and rear right cooking zone
displays indicate “7.” and “4” (power 7.4 kW).
3. Release the knobs.
4. Repeat steps 2 and 3 to change the power
limitation until "4." and "8” (4.8 kW power)
or "3." and "7" (3.7 kW power) appear on
the respective displays.
After having released the knobs on the required
power level, wait until the displays turn off to
save the changes.
The power level can be changed again
up to 4 minutes after the displays have
turned off, without having to disconnect
the appliance from the power supply.
The last power setting will remain valid
even in the event of a power failure.
Controls lock
The controls lock is a device that protects the
appliance from accidental or inappropriate use.
1. With all cooking zones switched off, turn the
two knobs corresponding to the front and
rear right zones to position “A”.
2. Keep them turned until the symbols
appear on the display.
3. Release the knobs.
USE - 4391477A166/C
In order to remove the controls lock, repeat the
same operations that were described
previously.
After a prolonged period of interruption
to the power supply, the control lock
will be deactivated. In this case,
activate it as described above.
Error codes
The symbol indicates that one or more
knobs have been held in the “A” or “M-A”
positions for more than 30 seconds. Release the
knobs to make the error message disappear. If
the display shows error code or ,
contact technical assistance.
Using the storage compartment
(where present)
See General safety instructions.
Opening and closing the door of the
multifunction oven
Multifunction ovens are equipped with a swing
door. To open, pull the door handle towards
you. To close, push the doors until you hear a
mechanical “click”.
List of traditional cooking functions
Not all functions are available on some
models.
The storage compartment is in the bottom of the
cooker. To open it, pull it towards you. It can be
used to store cookware or metallic objects
necessary when using the appliance.
Using the oven
See General safety instructions.
Switching on the oven
To switch on the oven:
1. Select the cooking function using the
function knob.
2. Select the temperature using the
temperature knob.
Ensure that the programmer clock
shows the cooking duration symbol
, otherwise it will not be possible to
turn on the oven.
Press the and buttons at the
same time to reset the programmer
clock.
STATIC
Traditional cooking, ideal for preparing
a single dish. For example cooking
roast meats, fatty meats, bread, pies.
CIRCULAIRE + BOTTOM
Allows you to quickly finish cooking
food that is already cooked on the
surface but not internally. Ideal for
quiches, suitable for all kinds of dishes.
GRILL
Produces excellent grilling and
gratinating results. When used at the
end of cooking, gives a uniform
browning to dishes.
RAPID DEFROST
Activating the fan on its own ensures a
uniform distribution of room temperature
air inside the oven, allowing any type of
food to be defrosted.
FAN ASSISTED
Intense and uniform cooking. Ideal for
biscuits, cakes and cooking on more
than one level.
44 - USE 91477A166/C
e
CIRCULAIRE
AA
The heat is distributed quickly and
uniformly. Suitable for all dishes, ideal
for cooking on multiple levels without
mixing smells or flavours.
FAN WITH GRILL
Allows optimal grilling, even for thick
slices of meat. Perfect for larger cuts of
meat.
ECO
This function is particularly suitable for
cooking on a single shelf with low
energy consumption.
It is recommended for all types of food
except those that may produce a large
amount of moisture (e.g. vegetables).
To obtain maximum energy savings and
reduce cooking times, it is
recommended to place food in the
oven without preheating.
When using the ECO function, avoid
opening the door during cooking.
Cooking (and preheating) times are
longer with the ECO function and may
depend on the amount of food in the
oven.
VAPOR CLEAN (on some models only)
This function facilitates cleaning using
the steam produced by a small amount
of water poured onto the depression on
the bottom.
Digital programmer
Minute minder timer button
Cooking duration button
End of cooking button
Value decrease button
Value increase button
Ensure that the programmer clock
shows the cooking duration symbol
, otherwise it will not be possible to
turn on the oven.
Press the and buttons at the
same time to reset the programmer
clock.
Setting the time
If the time is not set, the oven will not
switch on.
On the first use, or after a power failure, the
digits will be flashing on the
appliance’s display.
1. Press the and buttons at the same
time. The dot between the hours and the
minutes flashes.
2. The time can be set using the and
buttons. Keep the button pressed in to
increase or decrease rapidly.
3. Wait 5 seconds. The dot between the hours
and the minutes stops flashing.
4. The symbol on the display indicates that
the appliance is ready to start cooking.
Timed cooking
Timed cooking is the function which
allows a cooking operation to be
started and then ended after a specific
length of time set by the user.
1. After selecting a cooking function and
temperature, press the button.
2. Use the or button to set the
duration.
3. Wait approx. 5 seconds without pressing
any button in order for the function to
activate. The current time and the and
symbols will appear on the display.
4. At the end of cooking the heating elements
will be deactivated. On the display, the
USE - 4591477A166/C
symbol turns off, the symbol flashes and
AA
AA
AA
the buzzer sounds.
5. To turn the buzzer off, simply press one of
the programmer clock buttons.
6. Press the and buttons at the same
time to reset the programmer clock.
It is not possible to set a cooking time of
more than 10 hours.
To display the remaining cooking time,
press the button.
To reset the program, press the and
buttons at the same time. The oven
will then have to be switched off
manually.
Programmed cooking
Programmed cooking is the function that
allows timed cooking to be stopped at
a time set by the user.
1. Set the cooking time as described in the
previous point Timed cooking.
2. Press the button. The cooking end time
will appear on the display (current time plus
cooking duration).
3. Press the or button to set the
cooking end time.
4. Wait approx. 5 seconds without pressing
any button in order for the function to
activate. The current time and the
symbol appear on the display.
5. At the end of cooking the heating elements
will be deactivated. On the display, the
symbol turns off, the symbol flashes and
the buzzer sounds.
To reset the program, press the and
buttons at the same time. The oven
will then have to be switched off
manually.
To display the remaining cooking time,
press the button.
To display the end of cooking time,
press the button.
Minute minder timer
The minute minder timer does not stop
the cooking operation but rather informs
the user when the set time has run out.
The minute minder timer can be activated at any
time.
1. Pressing button causes to
appear on the display and the light
flashes.
2. Use the or button to set the
duration.
3. Wait approx. 5 seconds without pressing
any button to finish setting the minute minder.
The current time and the and
symbols appear on the display.
A buzzer will sound when the set time is
reached.
4. Press the decrease button to turn the
buzzer off.
The minute minder timer can be set from
1 minute to a maximum of 23 hours and
59 minutes.
To display the time remaining, press the
button.
Deleting the set data
Press the and buttons at the same time
to reset the programs set.
Setting the volume of the buzzer
The buzzer can have 3 tones.
When the buzzer is in operation, press the
button to change the setting.
Cooking advice
General advice
• Use a fan assisted function to achieve
consistent cooking at several levels.
• It is not possible to shorten cooking times by
increasing the temperature (the food could
be overcooked on the outside and
undercooked on the inside).
Advice for cooking meat
• Cooking times vary according to the
thickness and quality of the food and to
consumer taste.
• Turn the food to brown on both sides.
46 - USE 91477A166/C
e
• Use a meat thermometer when roasting
meat, or simply press on the roast with a
spoon. If it is hard, it is ready; if not, it needs
to be cooked for a few more minutes.
Advice for cooking with the Grill
• Meat can be grilled even when it is put into
the cold oven or into the preheated oven if
you wish to change the effect of the
cooking.
• With the Fan with grill function (if present),
we recommend that you preheat the oven
before grilling.
• We recommend placing the food at the
centre of the rack.
• With the Grill function, we recommend that
you set the temperature to the maximum
value to optimise cooking.
Advice for cooking desserts/pastries and
biscuits
• Use dark metal moulds: They help to absorb
the heat better.
• The temperature and the cooking time
depend on the quality and consistency of
the dough.
• To check whether the dessert is cooked right
through: At the end of the cooking time, put
a toothpick into the highest point of the
dessert. If the dough does not stick to the
toothpick, the dessert is cooked.
• If the dessert collapses when it comes out of
the oven, on the next occasion reduce the
set temperature by about 10°C, selecting a
longer cooking time if necessary.
Advice for cooking on two shelves:
• We recommend using two racks (they can
be obtained from Authorised Assistance
Centres).
• To facilitate the flow of air, place the
moulds/ovenware at the centre of the racks
and make sure that their width/diameter
does not exceed 30 cm.
• Position the racks keeping an empty shelf
between them.
• Depending on the type of food and the
increased quantity in the oven, cooking on
two levels may take slightly longer
compared to cooking on a single shelf.
• We suggest using the following functions
when cooking on two shelves: CIRCULAIRE
and CIRCULAIRE+BOTTOM.
Advice for defrosting and proving
• Place frozen foods without their packaging
in a lidless container on the first shelf of the
oven.
• Avoid overlapping the food.
• To defrost meat, use the rack placed on the
second level and a tray on the first level. In
this way, the liquid from the defrosting food
drains away from the food.
• The most delicate parts can be covered with
aluminium foil.
• For successful proving, a container of water
should be placed in the bottom of the oven.
Cooking information table (multifunction oven)
Food
Lasagne 3 - 4 STATIC 1 220 - 230 45 - 50
Pasta bake 3 - 4 STATIC 1 220 - 230 45 - 50
Weight
(Kg)
Function Shelf
Temp.
(°C)
Time
(minutes)
Veal roast 2 CIRCULAIRE 2 180 - 190 90 - 100
Pork loin 2 CIRCULAIRE 2 180 - 190 70 - 80
Sausages 1.5 FAN WITH GRILL 3 260 15
Roast beef 1 CIRCULAIRE 2 200 40 - 45
Roast rabbit 1.5 CIRCULAIRE 2 180 - 190 70 - 80
Turkey breast 3 CIRCULAIRE 2 180 - 190 110 - 120
Roast pork neck 2 - 3 CIRCULAIRE 2 180 - 190 170 - 180
The times indicated in the table do not include preheating times and are provided only as a guide.
USE - 4791477A166/C
Food
Roast chicken 1.2 CIRCULAIRE 2 180 - 190 65 - 70
Pork chops 1.5 FAN WITH GRILL 3 260 15 5
Spare ribs 1.5 FAN WITH GRILL 3 260 10 10
Bacon 0.7 GRILL 4 260 7 8
Pork fillet 1.5 FAN WITH GRILL 3 260 10 5
Beef fillet 1 GRILL 4 260 10 7
Salmon trout 1.2 CIRCULAIRE 2 160 - 170 35 - 40
Monkfish 1.5 CIRCULAIRE 2 160-170 60 - 65
Turbot 1.5 CIRCULAIRE 2 160-170 45 - 50
Pizza 1 FAN ASSISTED 2 260 8 - 9
Bread 1 CIRCULAIRE 2 190 - 200 25 - 30
Focaccia 1 CIRCULAIRE 2 180 - 190 20 - 25
Bundt cake 1 CIRCULAIRE 2 160 55 - 60
Tart 1 STATIC 2 170 30 - 40
Ricotta cake 1 CIRCULAIRE 2 160 - 170 55 - 60
Jam tarts 1 CIRCULAIRE 2 160 20 - 25
Paradise cake 1.2 CIRCULAIRE 2 160 55 - 60
Profiteroles 1.2 CIRCULAIRE 2 180 80 - 90
Sponge cake 1 CIRCULAIRE 2 150 - 160 55 - 60
Rice pudding 1 CIRCULAIRE 2 160 55 - 60
Brioches 0.6 CIRCULAIRE 2 160 30 - 35
The times indicated in the table do not include preheating times and are provided only as a guide.
Weight
(Kg)
Function Shelf
Temp.
(°C)
Time
(minutes)
st
1
surface 2nd surface
Cooking information table (auxiliary oven)
Food
Sausages 1.5 GRILL 2 MAX 13 - 15
Pork chops 1.5 GRILL 2 MAX 15 5
Spare ribs 1.5 GRILL 2 MAX 10 10
Bacon 0.7 GRILL 2 MAX 7 8
The times indicated in the table do not include preheating times and are provided only as a guide.
Weight
(Kg)
Function Shelf
48 - USE 91477A166/C
Temp.
(°C)
Time
(minutes)
1st surface 2nd surface
e
Food
Pork fillet 1.5 GRILL 2 MAX 10 5
Beef fillet 1 GRILL 2 MAX 10 7
The times indicated in the table do not include preheating times and are provided only as a guide.
Weight
(Kg)
Function Shelf
Temp.
(°C)
Time
(minutes)
CLEANING AND MAINTENANCE
Cleaning the appliance
See General safety instructions.
Cleaning the surfaces
To keep the surfaces in good condition, they
should be cleaned regularly after use. Let them
cool first.
Ordinary daily cleaning
Always and only use specific products that do
not contain abrasives or chlorine-based acids.
Pour the product onto a damp cloth and wipe
the surface, rinse thoroughly and dry with a soft
cloth or a microfibre cloth.
Food stains or residues
Do not use steel sponges and sharp scrapers as
they will damage the surface.
Use normal, non-abrasive products and a
wooden or plastic tool, if necessary. Rinse
thoroughly and dry with a soft cloth or a
microfibre cloth.
Do not allow residues of sugary foods (such as
jam) to set inside the oven. If left to set for too
long, they might damage the enamel lining of
the oven.
Cleaning the glass ceramic hob
See General safety instructions.
Clean and maintain the hob using an ordinary
glass ceramic cleaning product. Always follow
the manufacturer’s instructions. The silicon in
these products creates a protective, waterrepellent membrane which also resists dirt. All
marks stay on the membrane and can therefore
be removed easily. After cleaning, dry the
surface with a clean cloth. Make sure that there
is no detergent left on the cooking surface as it
might undergo an aggressive reaction when
heated up and could modify the structure of the
cooking surface.
Food stains or residues
Light coloured marks from pans with aluminium
bases can be easily cleaned off with a cloth
moistened in vinegar. Remove any burnt-on
residues after cooking; then rinse with water and
dry thoroughly with a clean cloth. Dirt, which
may have fallen on the hob while cleaning
lettuce or potatoes, can scratch the hob when
moving pans. Consequently, remove any dirt
from the cooking surface immediately. Changes
in colour do not affect the operation and
stability of the glass. These are not alterations to
the material of the hob but just residues which
have not been removed and have then
carbonised. Shiny surfaces can form due to the
bases of pans, especially aluminium ones,
rubbing on the surface, and due to the use of
unsuitable detergents. They are difficult to
remove using conventional cleaning products. It
may be necessary to repeat the cleaning
process several times. Use of corrosive
detergents or rubbing of pan bases can wear
away the decoration on the hob over time and
contribute to the formation of stains.
We recommend the use of cleaning
products distributed by the
manufacturer.
After cleaning, dry the appliance
thoroughly to prevent any water or
detergent from interfering with its
operation or creating unsightly marks.
CLEANING AND MAINTENANCE - 4991477A166/C
Knobs
Do not use aggressive products
containing alcohol or products for
cleaning steel and glass when cleaning
the knobs, as these products could
cause permanent damage.
The knobs should be cleaned with a soft cloth
dampened with lukewarm water, then dried
carefully. They can be removed by pulling them
out from their housings.
Cleaning the door
Cleaning the door glazing
The glass in the door should always be kept
thoroughly clean. Use absorbent kitchen roll. In
case of stubborn dirt, wash with a damp sponge
and an ordinary detergent.
Removing the door (auxiliary oven only)
For easier cleaning it is recommended to
remove the door and place it on a tea towel.
To remove the door proceed as follows:
1. Open the door completely and insert two
pins into the holes on the hinges indicated in
the figure.
that grooved sections A are resting
completely in the slots.
4. Lower the door and once it is in place
remove the pins from the holes in the hinges.
Removing the internal glass panes
For easier cleaning the internal glass panes of
the door can be removed.
Use kitchen paper to clean. In case of
stubborn dirt, wash with a damp
sponge and neutral detergent.
Multifunction oven door
1. Remove the internal glass pane by gently
pulling the top part, following the movement
indicated by the arrows in order to release
the 4 pins from their housings on the door.
2. Grasp the door on both sides with both
hands, lift it so that it forms an angle of
around 30° and remove it.
3. To reassemble the door, put the hinges in
the relevant slots in the oven, making sure
50 - CLEANING AND MAINTENANCE 91477A166/C
e
2. Then, pull the glass panel upwards, paying
22
22
11
11
22
22
11
11
attention to the brackets at the bottom of the
door.
3. After removing the inner glass, it is possible
to access the drip catcher strip.
4. Place the internal glass panel back onto the
brackets after cleaning. Make sure that you
centre and then insert the 4 pins firmly into
their housings on the door with the help of
the strips at the right and left in order to
achieve a perfect fit.
2. Then, pull the front part upwards (2). This
way, the 4 pins attached to the glass detach
from their housings in the oven door.
3. Remove the intermediate glass pane by
lifting it upwards.
4. Replace the intermediate glass panels after
cleaning.
5. Reposition the internal glass panel, taking
care to centre, then insert and secure the 4
pins into their slots in the oven door by
applying slight pressure.
Auxiliary oven door
1. Remove the internal glass panel by pulling
the rear part gently upwards, following the
movement indicated by the arrows (1).
Cleaning the oven cavity
In order to keep your oven in the best possible
condition, clean it regularly after letting it cool
down.
Avoid letting food residue dry inside the oven
cavity, as this could damage the enamel.
Take out all removable parts before cleaning.
CLEANING AND MAINTENANCE - 5191477A166/C
For easier cleaning, it is recommended to
remove:
•the door;
• The rack/tray support frames.
In the event you are using specific
cleaning products, we recommend
running the oven at maximum
temperature for 15-20 minutes in order
to eliminate any residue.
Drying
Cooking food generates moisture inside the
appliance. This is a normal phenomenon and
does not affect the appliance’s operation in any
way.
Each time you finish cooking:
1. Let the appliance cool down.
2. Remove any dirt from inside the appliance.
3. Dry the interior of the appliance with a soft
cloth.
4. Leave the door open until the inside of the
appliance has dried completely.
Removing racks/trays support frames
Removing the rack/tray support frames enables
the sides to be cleaned more easily.
To remove the rack/tray support frames:
• Pull the frame towards the inside of the oven
cavity to unhook it from its groove A, then
slide it out of the seats B at the back.
Cleaning the roof of the oven (only
for some models/cavities)
See General safety instructions.
Improper use
Risk of damage to the appliance
• Do not excessively flex the element during
cleaning.
The appliance is equipped with a tilting grill
element that allows for easy cleaning of the roof
of the oven cavity.
1. Free the upper heating element by gently
lifting it and rotating its retaining latch by 90
degrees.
2. Gently lower the heating element until it
stops.
3. When you have finished cleaning, place the
heating element back in position and turn
• When cleaning is complete, repeat the
above procedures to put the rack/tray
support frames back in.
52 - CLEANING AND MAINTENANCE 91477A166/C
the retaining latch to lock it in place.
e
Vapor Clean (on some models only)
See General safety instructions.
The Vapor Clean function is an assisted
cleaning procedure that facilitates the
removal of dirt. Thanks to this process, it
is possible to clean the inside of the
oven very easily. The dirt residues are
softened by the heat and water vapour
for easier removal afterwards.
Preliminary operations
Before starting the Vap o r Cl e an cycle:
• Completely remove all accessories from
inside the oven.
• Remove the temperature probe, if present.
• Remove the self-cleaning panels, if present.
• Pour approx. 120 cc of water onto the floor
of the oven. Make sure it does not overflow
out of the cavity.
• Spray a water and washing up liquid
solution inside the oven using a spray
nozzle. Direct the spray towards the side
walls, upwards, downwards and towards
the deflector.
We recommend spraying approx. 20
times at the most.
Do not spray the deflector if it has a selfcleaning coating.
• Close the door.
• During the assisted cleaning cycle, wash the
self-cleaning panels (where fitted), which
were previously removed, separately in
warm water and a small amount of
detergent.
Vapor Clean cycle setting
1. Turn the functions knob to symbol or
(where present).
2. Turn the temperature knob to the
symbol.
3. Allow the cleaning cycle to run for 18
minutes.
Vapor Clean End
1. Turn the function knob to 0 to exit from the
function.
2. Open the door and wipe away the less
stubborn dirt with a microfibre cloth.
3. Use a non-scratch sponge with brass
filaments on hard to remove deposits.
4. In case of grease residues use specific oven
cleaning products.
5. Remove the residual water inside the oven.
6. Replace the self-cleaning panels and the
rack/tray support frames, if fitted.
For greater hygiene and to avoid foods taking
on unpleasant odours:
• We recommend drying the inside of the
oven with a fan assisted function at 160°C
for around 10 minutes.
• If self-cleaning panels are fitted, we
recommend that you dry the inside of the
oven with a simultaneous catalytic cycle.
We recommend wearing rubber gloves
for these operations.
We recommend removing the door in
order to make the manual cleaning of
the parts that are difficult to reach
easier.
Extraordinary maintenance
Seal maintenance tips
The seal should be soft and elastic.
• To keep the seal clean, use a non-abrasive
sponge and wash with lukewarm water.
Replacing the internal light bulb
Power voltage
Danger of electrocution
• Unplug the appliance.
• Wear protective gloves.
1. Completely remove all accessories from
inside the oven.
2. Remove the rack/tray support frames.
3. Use a tool (e.g. a spoon) to remove the bulb
cover.
CLEANING AND MAINTENANCE - 5391477A166/C
Take care not to scratch the enamel of
LL
HH
II
CC CC
AA
BB
DD
the oven cavity wall.
4. Slide out and remove the light bulb.
Do not touch the halogen light bulb
directly with your fingers, use an
insulating material.
INSTALLATION
5. Replace the light bulb with one of the same
type (40 W).
6. Refit the cover. Ensure the moulded part of
the glass (A) is facing the door.
7. Press the cover completely down so that it
attaches perfectly to the bulb support.
The appliance must be installed by a
qualified technician and according to
the regulations in force.
Positioning
See General safety instructions.
Depending on the type of installation, this
appliance belongs to classes:
Class 1 Free-standing
Class 2 - subclass 1 Built-in
The appliance can be placed against walls that
are higher than the work surface, at a minimum
distance of X mm from the side of the appliance.
Any wall units installed above the appliance’s
worktop must be positioned at least Y mm from
it.
Appliance overall dimensions
Y 750 mm
If a hood is installed above the
appliance, refer to the hood instructions
manual to make sure the correct
clearance is left.
A 1103 mm
X 150 mm
54 - INSTALLATION 91477A166/C
B 600 mm
1
C
D 898 - 920 mm
H 750 mm
min. 150 mm
e
I 450 mm
888888
11031103
636,5636,5
5555
A
B
B
A
2
L
1
Minimum distance from side walls or other
flammable material.
2
Minimum cabinet width (=A)
Appliance dimensions
Position of electrical connection
Levelling the appliance
1103 mm
1. Loosen the 6 screws (A) on the back of the
hob and unscrew the two screws (B)
underneath.
2. Place the upstand on the hob. Align the 6
bottom slots of the upstand with the 6 screws
on the back of the hob that were previously
loosened.
3. Tighten the 6 screws on the back of the hob
and the 2 screws underneath.
The appliance must be level on the floor in order
to ensure greater stability:
• Screw or unscrew the feet at the bottom until
the appliance is stable and level on the
floor.
Assembling the upstand
The upstand must always be positioned and
secured correctly on the appliance.
The upstand provided is an integral part
of the product. It must be fastened to the
appliance prior to installation.
Mounting the plinth
The plinth must always be positioned and
secured correctly on the appliance.
INSTALLATION - 5591477A166/C
1. Place the plinth in the front bottom part of the
appliance.
2. Screw the two side screws to fasten the
plinth to the appliance.
3. Cover the holes of the plinth with the plugs
provided.
The plinth provided is an integral part of
the product; it must be fastened to the
appliance prior to installation.
Electrical connection
See General safety instructions.
The aforementioned power cables are
sized taking into account the
coincidence factor (in compliance with
standard EN 60335-2-6).
Replacement clamp
General information
Check the mains characteristics against the data
indicated on the plate.
The identification plate bearing the technical
data, serial number and brand name is visibly
positioned on the appliance.
Do not remove this plate for any reason.
The appliance must be connected to ground
using a wire that is at least 20 mm longer than
the other wires.
The appliance can work in the following modes:
220-240 V 2~
3 x 10 mm ²
three-core cable
220-240 V 3~
4 x 6 mm ²
four-core cable
220-240 V 1N~
3 x 10 mm ²
three-core cable
380-415 V 2N~
4 x 6 mm ²
four-core cable
380-415 V 3N~
5 x 4 mm ²
five-core cable
When connecting using a 10 sq. mm internal
section cable, the existing clamp must be
replaced with the one supplied in order to
ensure that the cable is secured correctly.
Fixed connection
Fit the power line with an all-pole circuit breaker
with a contact separation distance sufficient to
provide complete disconnection in category III
overvoltage conditions, pursuant to installation
regulations.
For the Australian/New Zealand market:
The circuit breaker incorporated in the fixed
connection must comply with AS/NZS 3000.
Instructions for the installer
• If you use a plug (if present) to connect to
the power supply, the plug must be
accessible after installation.
• Do not bend or trap the power cable.
• The appliance must be installed according
to the installation diagrams.
• If the appliance does not work correctly
after having carried out all the checks,
contact your local Authorised Service
Centre.
• Once the appliance has been installed,
please explain to the user how to use it
correctly.
The values indicated refer to the crosssection of the internal conductor.
56 - INSTALLATION 91477A166/C
Loading...