Smeg STA4645 User Manual
INSTRUCTION MANUAL
GGUUIIDDEE FFOORR UUSSIINNGG TTHHEE DDIISSHHWWAASSHHEERR AANNDD TTHHEE WWAASSHHIINNGG PPRROOGGRRAAMMSS
CONTENTS
CONTENTS
1 INTRODUCTION ........................................................................................ 3
2 DESCRIPTION AND USE OF THE CONTROLS .......................................... 5
2.1 Upper panel ............................................................................................... 5
2.2 Setting the washing program and switching on and off...............................6
2.2.1 Switching on .............................................................................................. 8
2.2.2 Selecting and starting the program ............................................................. 8
2.2.3 End of program ..........................................................................................8
2.2.4 Interrupting a program ................................................................................ 9
2.2.5 Changing the current program ...................................................................9
2.2.6 Canceling the current program ...................................................................9
2.2.7 Options ....................................................................................................10
2.2.8 Switching off ............................................................................................ 11
2.3 Additional features .................................................................................... 11
2.3.1 Adjusting the water softener ..................................................................... 11
EN
3 ENERGY SAVING AND ENVIRONMENTAL RESPECT .............................. 13
3.1 Reducing the consumption of detergent and respecting the environment .13
4 REMOVING THE DISHES ......................................................................... 14
5 TROUBLESHOOTING ..............................................................................15
Rev 0.0 1
EN
2 Rev 0.0
INTRODUCTION
1 INTRODUCTION
Thank you for choosing one of our products. To use this dishwasher
correctly and safely, please read this manual carefully. The manual is
divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide
answers to all your questions about use of the dishwasher.
Before using this dishwasher, carefully read chapter 2 “Use and
safety warnings” of the attached general manual.
For any other information about use and maintenance of the dishwasher, read the enclosed general manual carefully.
This manual comprises the following sections:
INTRODUCTION: general information about the manual
USER INSTRUCTIONS: advice on using the washing programs and
information about all the dishwasher functions.
Nomenclature of fi gures and tables:
The progressive number of each fi gure is shown in the bottom righthand corner of the relative box. An example of a progressive number
is “Fig. 4-01”, where the fi rst number (4) indicates the section to
which the fi gure belongs, while the second number (01) indicates
the progressive number of the fi gure in section 4 (Fig. 4-01 is the
fi rst fi gure in section 4). The tables are numbered in the same way,
bearing in mind that “Tab.” is used instead of “Fig.” (e.g.: Tab. 4-01
is the fi rst table in section 4). If a table occupies more than one page,
a letter is added after the progressive number (e.g.: “Tab. 4-01a”,
Tab. 4-01b”).
EN
Rev 0.0 3
EN
INTRODUCTION
Symbols used in this manual (see tab. 1-01)
DANGER. This symbol highlights information and warnings which, if not
observed, may compromise personal safety or damage the appliance.
This symbol highlights general information and warnings.
Tab. 1-01
4 Rev 0.0
USER INSTRUCTIONS
EN
2
DESCRIPTION AND USE OF THE CONTROLS
2.1 Upper panel
All the dishwasher controls are grouped on the upper panel (see fi g. 2-01). The
dishwasher can only be switched on, programmed, switched off, etc. with the
door open.
A brief description (see tab. 2-01) of the various controls on the upper panel is
given below.
On/off button
1
Press to power the appliance.
Program indicator lights
2
These show which program is selected and whether there are any faults (troubleshooting).
Program selection button
3
Press in sequence to select the required program.
Add salt indicator light (only fi tted on some models)
4
Shows the appliance has run out of salt.
Add rinse-aid indicator light (only fi tted on some models)
5
Shows the appliance has run out of rinse-aid.
Sanitation indicator light
6
Shows the function is active.
Program delay button (only fi tted on some models)
7
Press to delay the start of the program up to 9 hours.
8
Display (only fi tted on some models)
Fig. 2-01
Tab. 2-01
Rev 0.0 5
EN
USER INSTRUCTIONS
2.2 Setting the washing program and switching
on and off
The dishwasher is equipped with a control panel (see fi g. 2-02) which is used
to program the appliance and switch it on and off.
Fig. 2-02
To select the most suitable program for the dishes to wash, consult the following table which specifi es the most appropriate type of washing sequence
depending on the kind of dishes and how dirty they are (see tab. 2-02).
6 Rev 0.0
USER INSTRUCTIONS
EN
PROGRAM NUMBER
AND SYMBOL
1
2
3
4
5
RINSE
CRYSTAL
NORMAL
AUTO
DELICATE
EXTREME
WASH
ETL SANITATION
LISTED
DISHES AND
CUTLERY
Pans and
dishes waiting
for further
washing
Immediate
washing
after use for
moderately
dirty dishes
Immediate
washing
after use for
normally dirty
dishes
Normally dirty
dishes
Very dirty pans
and dishes
(except
delicate items)
PROGRAM
SEQUENCE
Cold pre-wash 16’
Wash at 45°C
(113°F).
Cold rinse.
Rinse at 69°C
(156.2°F).
Dry.
Cold pre-wash.
Wash at 55°C
(131°F).
Cold rinse.
Rinse at 68°C
(154.4°F).
Dry.
Cold pre-wash.
(Depending of the
type of dirty)
Wash at 55°C
(131°F).
Cold rinse.
Hot rinse at 69°C
(156.2°F).
Dry.
Pre-wash at 45°C
(113°F).
Wash at 70°C
(158°F).
2 cold rinses.
Rinse at 70°C
(158°F).
Dry.
TIME CONSUMPTION
MINUTES
(2)
58’
111’
90’-105’
117’
WATER
(1)
4.1 l
1.08 gal.
11.5 l
3.04 gal.
16.3 l
4.31 gal.
12-16 l
3.17-
4.23 gal.
20 l
5.28 gal.
ENERGY
KWh (2)
0.02
0.53
0.68
0.6-0.8
0,97
Tab. 2-02
(1) Average water consumption with the softener set to level 0 (zero).
Any other setting will increase water consumption till 2.5 l (0.66 gal.)/cycles with setting 5.
(2) The cycle times listed in the use and care manual are based on normal soil loads and 120°F
(49°C) incoming water and will vary based on your actual conditions.
- Only “EXTREME WASH” program conform to NSF std 184 and is certifi ed by INTERTEK with the
ETL SANITATION LISTED.
- When the “Sanitized” light shine it means that the dishwasher and its contents have been sani-
tized according to the requirements of the National Sanitation Foundation (NSF).
- When the “AUTO DELICATE” is selected, the dishwasher recognizes the type of dirt and auto-
matically adjusts the washing parameters as appropriate.
Rev 0.0 7
EN
USER INSTRUCTIONS
Only run the soak program with half loads.
After using the above table to choose the most suitable washing cycle, program the appliance.
Before starting a washing program, make sure that:
•
The water supply tap is open.
•
There is regenerating salt in the water softener tank (to add
salt, see the instructions in the general manual).
•
The correct amount of detergent has been added to the dispenser (to add detergent, see the instructions in the general
manual).
•
The spray arms are able to rotate freely and without obstruction.
•
The racks have been correctly loaded (see the instructions in the
general manual).
•
The dishwasher door is securely closed.
2.2.1 Switching on
Press the on/off button (ref. 1 fi g. 2-02) to start the dishwasher. Then wait for
one of the program indicator lights to turn on (ref. 2 fi g. 2-02).
2.2.2 Selecting and starting the program
•
Press the program selection button (ref. 3 fi g. 2-02) several times until
the indicator light corresponding to the required program turns on (ref. 2 fi g.
2-02);
•
if necessary, select, using the relative buttons, the complementary functions
you are interest in (e.g. “Programming delay”);
•
close the door; the program will start after about 2 seconds and the relative
indicator light will fl ash throughout the cycle (program running signal).
If the door of the dishwasher has not been closed or has been incorrectly closed, the washing cycle will not begin.
2.2.3 End of program
The end of the program is indicated by a brief acoustic signal and the (marked
by “end”) “auto delicate” and “extreme wash” program indicator lamps fl ash.
8 Rev 0.0
USER INSTRUCTIONS
2.2.4 Interrupting a program
To interrupt the current program simply open the door of the dishwasher; to
restart the program, simply close the door again. The program restarts from
where it was interrupted.
If it is necessary to open the door during the washing cycle, the
program will be interrupted, the relative indicator light will continue to
fl ash and a beep will indicate that the cycle has not terminated. Wait
for about 1 minute before closing the door and continuing with the
program. When the door closes, the program will start from where it
was interrupted. This operation should be performed only if neces-
sary as it could cause irregular program performance.
2.2.5 Changing the current program
To change the current program, simply open the door of the dishwasher and
select the new program. Close the door to run the new program automatically.
2.2.6 Canceling the current program
To cancel the current program, open the door and press and hold down
•
the program selection button (ref. 3 fi g. 2-02) for a few seconds until the
indicator lights of the fourth and fi fth programs turn on (ref. pr. 4, pr. 5 fi g.
2-03).
Close the door again.
•
After about 1 minute, the dishwasher terminates the cycle and the indicator
•
lights of the fourth and fi fth programs (ref. pr. 4, pr. 5 fi g. 2-03) start fl ashing.
EN
pr. 4
Rev 0.0 9
pr. 5
Fig. 2-03
EN
USER INSTRUCTIONS
2.2.7 Options
PROGRAM DELAY
The “Program delay” function delays the beginning of the washing program
up to 9 hours from the moment in which programming takes place. This makes
it possible to use the dishwasher at a certain time of day.
Before programming a delay, open the door of the dishwasher, select the
required washing program (see para 2.2 “Setting the washing program and
switching on and off”). Select the day by pressing the Program delay button
(ref. 7 fi g. 2-02); each time you press the button, the display increases the delay
before the appliance starts by 1 hour.
10 Rev 0.0
USER INSTRUCTIONS
2.2.8 Switching off
At the end of the program, the dishwasher emits a short beep and the indicator lights of the fourth and fi fth program (ref. pr. 4, pr. 5 fi g. 2-04) fl ash.
Turn off the appliance by opening the door and pressing the on/off button (ref.
1 fi g. 2-02).
EN
pr. 4
pr. 5
Fig. 2-04
2.3 Additional functions
2.3.1 Adjusting the water softener
N.B.: a different washing program from soak must be used to make
the following adjustment. .
Press and hold down the program delay button (ref. 7 fi g. 2-05) until the preset value appears followed by a dot (normally 3.). Release the button and then
press it again and again until the required value is displayed, as indicated in the
table (see tab. 2-03).
The 6 possible adjustment levels will appear in this sequence:
3., 4., 5., 0., 1., 2..
When the required value appears on the display, release the button; after 5
seconds the appliance automatically reverts to the program delay and the
adjustment is set to the chosen value.
Rev 0.0 11
EN
USER INSTRUCTIONS
N.B.: the display indicates the water hardness adjustment and the
program delay. A dot (.) after the number means that the water hardness adjustment is being displayed. If no dot (.) appears, the program delay is being displayed.
Water hardness table (see tab. 2-03)
WATER HARDNESS
German degrees (°D) French degrees (°F)
0 - 4 0 - 7 0 - 4.5 0.
5 - 15 8 - 25 4.6 - 14.5 1.
16 - 23 26 - 40 14.6 - 23.5 2.
American degrees
grains/galls
Fig. 2-05
SETTING
24 - 31 41 - 60 23.6 - 35 3.
32 - 47 61 - 80 35.1 - 46.5 4.
48 - 58 81 - 100 46.6 - 58.5 5.
Tab. 2-03
Contact your local water board for information on the hardness of your water
supply.
If it is necessary to open the door during the washing cycle, the
program will be interrupted, the relative indicator light will continue to
fl ash and a beep will indicate that the cycle has not terminated. Wait
for about 1 minute before closing the door and continuing with the
program. When the door closes, the program will start from where it
was interrupted. This operation should be performed only if neces-
sary as it could cause irregular program performance.
12 Rev 0.0
USER INSTRUCTIONS
3 ENERGY SAVING AND ENVIRONMENTAL
RESPECT
Always try to run the dishwasher fully loaded.
•
Do not wash the dishes under a running tap.
•
Use the most suitable washing program for each type of load.
•
Do not pre-rinse.
•
If available, connect the dishwasher to a hot water system with a tempera-
•
ture of up to 60°C (140°F).
When possible, skip the drying cycle by opening the door after washing:
•
the air and the residue heat will dry the dishes to perfection.
3.1 Reducing the consumption of detergent
and respecting the environment
The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity:
Separate the more delicate items from those that are more resistant to ag-
•
gressive detergents and high temperatures;
Do not pour the detergent directly onto the dishes.
•
EN
Rev 0.0 13
EN
USER INSTRUCTIONS
4 REMOVING THE DISHES
At the end of the washing program, wait at least 20 minute before
removing the dishes in order to allow them to cool. To prevent any
water droplets on the upper rack from falling onto the dishes in the
lower rack, empty the lower rack fi rst and then the upper one.
14 Rev 0.0
USER INSTRUCTIONS
5 TROUBLESHOOTING
The dishwasher can to signal a number of malfunctions by turning on various
indicator lights, as described below (see following table):
FAULT DESCRIPTION
Acquastop failure
E1
E3
E4
E5
E6
The anti-fl ooding system has tripped (only for models
fi tted with this feature). Activates in case of water leaks.
Contact the technical assistance service.
Water heating malfunction
The water is not heated or is incorrectly heated.
Repeat the washing program; if the problem persists,
contact the technical assistance service.
Water temperature monitoring malfunction
Interrupt the current program. Switch off the
dishwasher, switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
Water intake malfunction
The appliance does not take in water or does so
incorrectly. Make sure the water connections are
correct, that the water supply tap is open and that the
fi lter is not clogged. If the problem persists, contact
the technical assistance service.
Water pump-out malfunction
The appliance does not pump out the water or does
so incorrectly. Make sure the drain hose is not kinked
or crushed and that the siphon and fi lters are not
clogged. If the problem persists, contact the technical
assistance service.
Tab. 4-01
EN
Light off Light on Light fl ashing
Rev 0.0 15
EN
USER INSTRUCTIONS
If an alarm situation occurs, the dishwasher interrupts the current program and
signals the fault.
Alarms E1, E3, E4, immediately terminate the current program.
•
Alarms E5, E6 interrupt the current program and, after the problem has been
•
eliminated, resume the cycle.
To “reset” an alarm:
open or close the door, or switch the appliance on and back off again. At this
•
point, the dishwasher can be programmed again.
If the fault persists, contact the Authorized Technical Assistance Service.
16 Rev 0.0
CONTENTS
Contents
1 INTRODUCTION ........................................................................................ 3
2 IMPORTANT SAFETY INSTRUCTION .........................................................5
3 INSTALLATION AND HOOK-UP ...............................................................11
4 OPERATING INSTRUCTIONS .................................................................. 14
4.1 Using the water softening system ............................................................. 15
4.2 Using the rinse-aid and detergent dispensers ........................................... 17
4.2.1 Adding the rinse-aid ................................................................................. 18
4.2.2 Adjusting the rinse-aid dispenser system .................................................. 18
4.2.3 Adding the detergent ...............................................................................19
4.3 General warnings and recommendations .................................................21
4.4 Using the racks ........................................................................................ 23
4.4.1 Lower rack ...............................................................................................24
4.4.2 Cutlery basket ..........................................................................................26
4.4.3 Upper rack ...............................................................................................27
EN
5 CLEANING AND USER-MAINTENANCE .................................................. 30
5.1 General warnings and recommendations for correct maintenance ............ 30
5.2 Cleaning the water intake fi lter (only some models) ................................... 31
5.3 Cleaning the spray arms ........................................................................... 31
5.4 Cleaning the fi lter unit ............................................................................... 33
5.5 Maintenance warnings and advice ........................................................... 34
5.6 Troubleshooting minor problems .............................................................. 35
6 TECHNICAL DATA ...................................................................................37
Rev 0.0 1
EN
2 Rev 0.0
INTRODUCTION
1 INTRODUCTION
Thank you for choosing one of our products. To use this dishwasher
correctly and safely, please read this manual carefully. The manual
is divided into sections giving you a step-by-step guide to all your
appliance’s functions. The texts are easy to understand and are
complete with detailed illustrations. Following the cleaning instructions provided here will keep dishwasher performance at peak levels
in the long term. This user-friendly manual will provide answers to all
your questions about use of the dishwasher.
This manual comprises the following sections:
INTRODUCTION: general information about the manual.
WARNINGS: a list of warnings concerning safety and use of the
dishwasher.
INSTALLATION INSTRUCTIONS: for the qualifi ed technician who
must carry out the installation, hook-up and testing of the appliance.
USER INSTRUCTIONS: useful advice is provided for the use of
racks, spray arms, containers and fi lters.
EN
Nomenclature of fi gures and tables:
The progressive number of each fi gure is shown in the bottom righthand corner of the relative box. An example of a progressive number
is “Fig. 4-01”, where the fi rst number (4) indicates the section to
which the fi gure belongs, while the second number (01) indicates
the progressive number of the fi gure in section 4 (Fig. 4-01 is the
fi rst fi gure in section 4). The tables are numbered in the same way,
bearing in mind that “Tab.” is used instead of “Fig.” (e.g.: Tab. 4-01
is the fi rst table in section 4). If a table occupies more than one page,
a letter is added after the progressive number (e.g.: “Tab. 4-01a”,
Tab. 4-01b”).
Rev 0.0 3
EN
INTRODUCTION
Symbols used in this manual (see tab. 1-01)
DANGER. This symbol highlights information and warnings which,
if not observed, may compromise personal safety or damage the
appliance.
DANGER OF ELECTROCUTION. This symbol highlights information
and warnings of an electrical nature which, if not observed, may
compromise personal safety or damage the appliance.
This symbol highlights general information and warnings.
Tab. 1-01
4 Rev 0.0
WARNINGS
2 IMPORTANT SAFETY INSTRUCTION
(Save this instructions)
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE
DISHWASHER (INCLUDING THE “INSTALLATION” AND “DESCRIPTION OF CONTROLS” MANUALS, IF ATTACHED). BEFORE USING
THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS
CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH
THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED
FOR DOMESTIC USE, AND COMPLIES WITH THE DIRECTIVES
CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND
ELIMINATION OF RADIO FREQUENCY INTERFERENCE. THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE: WASH-
ING AND DRYING OF DISHES; ANY OTHER USE SHALL BE
CONSIDERED IMPROPER. THE MANUFACTURER DECLINES
ALL RESPONSIBILITY FOR USES OTHER THAN THOSE DESCRIBED ABOVE
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL
NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR. THE NAME PLATE MUST NEVER
BE REMOVED.
THIS APPLIANCE IS NOT SUITABLE FOR USE ON BOATS, CARAVANS OR THE LIKE.
DISHWASHERS CERTIFIED FOR DOMESTIC USE ARE NOT SUITABLE FOR AUTHORISED FOOD FACTORIES.
EN
CHECK THAT THE VOLTAGE, FREQUENCY AND PROTECTION OF
THE DOMESTIC MAINS POWER SUPPLY MATCH THE RATINGS
ON THE NAME PLATE OF THE APPLIANCE.
DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST SORTED
WASTE COLLECTION CENTRE. KEEP CHILDREN, PHYSICALLY
AND/OR MENTALLY IMPAIRED ADULTS, AND ANIMALS AWAY
FROM PACKAGING WASTE; DANGER OF SUFFOCATION.
Rev 0.0 5
EN
WARNINGS
BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE
MAINS POWER SUPPLY FROM THE WORK AREA.
DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING WITH CONSEQUENT FIRE HAZARD.
DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF
ON THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY
GLOVES.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN FORCE. IF IN DOUBT, HAVE THE SYSTEM CHECKED
BY A QUALIFIED ELECTRICIAN (SEE ALSO THE WARNINGS INDICATED IN CHAPTER 3).
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
DAMAGE TO PERSONS OR PROPERTY RESULTING FROM
THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO
AVOID WASTING ELECTRICITY.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER
FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE
WATER TAP.
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER. THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE
WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER
OR BY A QUALIFIED TECHNICIAN.
ONLY USE DETERGENTS SPECIALLY FORMULATED FOR DISHWASHERS. DO NOT USE DETERGENTS FORMULATED FOR
WASHING DISHES BY HAND.
6 Rev 0.0
WARNINGS
ONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC
DISHWASHERS.
DO NOT INHALE OR SWALLOW DETERGENT AS THIS MAY CAUSE
BURNS AND/OR PERMANENT DAMAGE TO THE NOSE, MOUTH
AND THROAT, AND EVEN LEADING TO SUFFOCATION; KEEP DETERGENT AWAY FROM YOUR EYES. IF ONE OF THE ABOVE SITUATIONS OCCURS, SEEK MEDICAL ASSISTANCE IMMEDIATELY.
TO PREVENT CHILDREN FROM COMING INTO CONTACT WITH
DETERGENT, FILL THE DISHWASHER JUST BEFORE STARTING
THE WORK PROGRAM AND THEN KEEP THE DETERGENT OUT
OF THE REACH OF CHILDREN.
THIS DISHWASHER MUST BE USED BY ADULTS. USE BY PERSONS WITH REDUCED MENTAL AND/OR PHYSICAL CAPABILITIES IS ONLY PERMITTED UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY.
DO NOT ALLOW CHILDREN TO APPROACH AND/OR PLAY IN OR
ON THE DISHWASHER. THE APPLIANCE MAY CONTAIN RESIDUES OF DETERGENT WHICH CAN CAUSE PERMANENT DAMAGE TO THE EYES, MOUTH AND THROAT, AS WELL AS POSSIBLE DEATH BY SUFFOCATION; IF THE ABOVE OCCURS, SEEK
MEDICAL ASSISTANCE IMMEDIATELY.
BEWARE; IT IS POSSIBLE FOR CHILDREN TO GET TRAPPED INSIDE THE DISHWASHER!
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION.
EN
DO NOT POUR POWDER AND/OR LIQUID DETERGENT INTO THE
RINSE-AID CONTAINER AS THIS WILL DAMAGE THE CONTAINER.
DO NOT POUR POWDER AND/OR LIQUID DETERGENT INTO THE
WASTER SOFTENER TANK AS THIS WILL DAMAGE THE TANK.
DO NOT USE INDUSTRIAL DETERGENTS AS THIS MAY DAMAGE
THE APPLIANCE AND/OR TRIGGER VIOLENT CHEMICAL REACTIONS (E.G. EXPLOSIVE GAS).
DO NOT LOAD DISHES THAT ARE SOILED WITH ASH, WAX OR
PAINTS.
Rev 0.0 7
EN
WARNINGS
DO NOT INTRODUCE ITEMS IN HEAT-SENSITIVE PLASTI¬C,
SUCH AS DISPOSABLE CUTLERY OR PLATES, AS THESE MAY
BECOME DEFORMED. DO NOT WASH OBJECTS IN PLASTIC UNLESS THEY ARE MARKED “DISHWASHER PROOF” OR THE LIKE.
FOR UNMARKED OBJECTS, FOLLOW THE INSTRUCTIONS OF
THE MANUFACTURER; IF NO INFORMATION IS AVAILABLE, DO
NOT WASH THESE OBJECTS IN THE DISHWASHER.
DO NOT INTRODUCE ANIMALS INTO THE DISHWASHER.
WHEN OPENING THE DISHWASHER DOOR DURING A CYCLE
THERE IS A RISK OF SCALDING DUE TO THE HEAT CONTAINED
INSIDE; DO NOT GET IN THE WAY OF THE STEAM LEAVING THE
APPLIANCE AND DO NOT TOUCH THE COMPONENTS INSIDE.
WAIT 20 MINUTES AFTER THE END OF THE WASHING CYCLE
OR AFTER INTERRUPTING IT BEFORE REMOVING THE DISHES IN
ORDER TO ALLOW THEM TO DRY.
IN CERTAIN SITUATIONS, HYDROGEN MAY BE GENERATED INSIDE A HOT WATER SYSTEM THAT HAS NOT BEEN USED FOR
OVER TWO WEEKS. HYDROGEN IS AN EXPLOSIVE GAS. IF THE
HOT WATER SYSTEM HAS NOT BEEN USED FOR TWO WEEKS
OR MORE, OPEN ALL THE HOT WATER TAPS AND ALLOW THE
WATER TO RUN FOR A FEW MINUTES BEFORE USING THE DISHWASHER. THIS WILL DISCHARGE ANY HYDROGEN BUILDUPS.
AS THIS GAS IS FLAMMABLE, DO NOT SMOKE OR USE NAKED FLAMES WHILE PERFORMING THIS OPERATION.
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN
OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTTING PEOPLE AT RISK. NEVER LEAVE THE DISHWASHER
DOOR OPEN; PEOPLE MIGHT TRIP OVER IT.
DO NOT LEAN AGAINST OR STAND ON THE DISHWASHER
RACKS.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT
INSIDE THE DISHES OR DISHWASHER.
8 Rev 0.0
WARNINGS
KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST
BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID
HORIZONTAL IN THE UPPER RACK. TAKE CARE NOT TO CUT
YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM
THE RACK.
POSITION SHARP/POINTED OBJECTS SO AS TO PREVENT THEM
FROM DAMAGING THE DOOR GASKETS.
DO NOT OPERATE THE DISHWASHER UNLESS ALL THE OUTER
PANELS HAVE BEEN POSITIONED CORRECTLY.
DO NOT TAMPER WITH THE DISHWASHER CONTROLS.
AQUASTOP MODELS; THE AQUASTOP DEVICE PREVENTS
FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED (THE ERROR IS INDICATED ON THE
DISPLAY), CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND
REPAIR THE FAULT. IN MODELS EQUIPPED WITH THE AQUASTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER
INTAKE HOSE. DO NOT CUT THE HOSE AND DO NOT ALLOW
THE SOLENOID VALVE TO DROP INTO WATER. IN THE EVENT
OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE
APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM
THE WATER SUPPLY.
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM
A QUICK TEST OF THE APPLIANCE (SEE “INSTALLATION” MANUAL). IF THE DISHWASHER FAILS TO OPERATE CORRECTLY,
DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND
CALL THE NEAREST TECHNICAL SERVICE CENTRE. DO NOT
ATTEMPT TO REPAIR THE APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT
BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND
ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD
BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORIZED
TECHNICIAN: REPAIRS CARRIED OUT BY UNAUTHORIZED
PERSONS WILL INVALIDATE THE WARRANTY, AS WELL AS
POSING A POTENTIAL HAZARD TO THE USER.
EN
Rev 0.0 9
EN
WARNINGS
BEFORE CLEANING OR SERVICING THE APPLIANCE, REMOVE
THE PLUG OR TURN OFF THE MULTI-POLE SWITCH.
REMOVE THE WASHING COMPARTMENT DOOR AND DISCONNECT THE MAINS POWER SUPPLY WHEN REMOVING THE OLD
DISHWASHER FOR MAINTENANCE OR DISPOSAL.
THE SYMBOL ON THE PRODUCT, OR ON THE DOCUMENTS
ACCOMPANYING THE PRODUCT, INDICATES THAT THIS APPLIANCE MAY NOT BE TREATED AS HOUSEHOLD WASTE. INSTEAD
IT SHALL BE HANDED OVER TO THE APPLICABLE COLLECTION
POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC
EQUIPMENT. DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH LOCAL ENVIRONMENTAL REGULATIONS FOR
WASTE DISPOSAL. FOR MORE DETAILED INFORMATION ABOUT
TREATMENT, RECOVERY AND RECYCLING OF THIS PRODUCT,
PLEASE CONTACT YOUR LOCAL CITY OFFICE, YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU
PURCHASED THE PRODUCT.
BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY,
YOU WILL HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH.
THE MANUFACTURER DECLINES ALL RESPONSIBIL-
ITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPERTY RESULTING FROM FAILURE TO OBSERVE THE ABOVE
PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE
COMPONENT OF THE APPLIANCE, OR FROM THE USE OF
UNORIGINAL SPARE PARTS.
IF IN DOUBT ABOUT THE CONTENTS OF THIS MANUAL,
CONTACT THE TECHNICAL ASSISTANCE SERVICE.
10 Rev 0.0
INSTALLATION INSTRUCTIONS
3 INSTALLATION AND HOOK-UP
To install and hook up this appliance, consult the attached installation
manual.
Bear in mind the following warnings when installing and hooking up the dishwasher.
DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF
ON THE SHARP EDGES OF THE APPLIANCE; WEAR SAFETY
GLOVES.
INSTALLATION, REPAIRS AND SERVICING MUST BE PERFORMED BY QUALIFIED AND AUTHORIZED TECHNICIANS.
AS WELL AS INVALIDATING THE WARRANTY, WORK CARRIED
OUT BY UNAUTHORIZED PERSONS MAY GENERATE HAZARDS.
INSTALLATION MUST BE PERFORMED IN COMPLIANCE WITH
ALL THE DIRECTIVES IN FORCE IN THE COUNTRY OF INSTALLATION AND, IF THESE DO NOT EXIST: IN THE UNITED STATES THE
NATIONAL ELECTRIC CODE; IN CANADA THE CANADIAN ELECTRIC CODE C22.1 - LATEST EDITION/PROVINCIAL AND MUNICIPAL CODES AND/OR LOCAL CODES.
BUILDING-IN A DISHWASHER UNDERNEATH A CERAMIC HOB IS
ABSOLUTELY FORBIDDEN. A DISHWASHER CAN BE BUILT-IN
UNDERNEATH A CONVENTIONAL HOB PROVIDED THERE IS NO
BREAK IN THE KITCHEN WORKTOP, AND THE DISHWASHER
AND HOB ARE INSTALLED AND SECURED CORRECTLY, SO
THAT NO HAZARDS ARE GENERATED .
PREVENTING THE RISK OF CLOGGING OR DAMAGE: IF THE
WATER PIPE IS NEW OR HAS NOT BEEN USED FOR A LONG
TIME, BEFORE CONNECTING TO THE WATER SUPPLY CHECK
THAT THE WATER IS CLEAR AND FREE OF IMPURITIES, TO PREVENT DAMAGE TO THE APPLIANCE. THE DISHWASHER MUST
ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH
NEW HOSES; OLD OR USED HOSES MUST NEVER BE REUSED .
EN
Rev 0.0 11
Loading...