Smeg SIHP40WG4 Quick Start Manual
SIHP40WG4
smeg 40cm induction cooktop with wok recess
ID161012
Code SIHP40WG4
EAN 3706012861123
finish black ceramic surface, frameless, straight
edging, concave wok recess
accessory supplied stainless steel wok utensil
size 400mmW x 520mmD x 131mmH
NB: height includes 4.36mm ceramic
thickness
cutout 365mmW x 465mmD
capacity single concave zone, 314mm diameter,
2300 watts with 3000 watt power boost
thermostat nine heat settings plus power boost
total wattage 3000 watts
current 12.5 amps
electrical
connection
dedicated 15 amp power cord and socket
or hard wired; power cord is not supplied
timers safety maximum operating timer,
delay stop timer, 99 minute maximum
variable programmable timer
safety LEDs, cooling fan, residual heat indicators,
thermal overload protection
pan size automatic electronic ignition
warranty two years parts and labour
The SIHP40WG4 has one induction cooking zone — a 314mm
diameter concave specialist wok zone. The heat for cooking is
generated in the base of the cooking utensil and not generated by a
high-wattage element below the ceramic cooktop surface. There is
neither heat nor time lost in heating a medium such as the element
itself and the ceramic surface. This energy (heat) creation is direct and
fast. An induction ceramic cooktop is extremely energy, time and cost
efficient.
There is an induction coil just below the ceramic surface. This
induction coil produces an electro-magnetic field when electrical
power is supplied to the cooktop and the zone is selected. With the
placement of a magnetised utensil onto the induction zone, heat is
created instantly in the base of the utensil. This instant and highlycontrollable heat cooks the food. Importantly, if the utensil is removed
from the induction zone, the electromagnetic energy (heat) is instantly
stopped. There is no waste of electricity.
PLEASE NOTE: magnetised utensils with steel, steel mesh and castiron bases are required for induction cooktops, although not all
magnetised utensils are suitable. When purchasing utensils, always
check the label for ‘
suitable for induction
’. Advantageously, induction
utensils can be used on gas, ceramic and solid electric plate cooktops.
However, what is suitable for these latter cooktop versions is not
necessarily suitable for induction cooktops.
PAN RECOGNITION
Provided the utensil’s (wok) contact surface covers approximately sixtypercent of the inner circle’s area, cooking will initiate. Anything less
will not be recognised by the induction coil and no power is supplied.
Utensil bases larger than the inner circle are recognised and the
appropriate power requirement is adjusted automatically.
FLUSHMOUNT
As an alternative to the traditional topmounting of a cookktop onto a
benchtop, consider flushmounting into a benchtop.
Topmounting is when the cooktop sits into a precut cavity with the
entire cooktop’s surface sitting a few millimetres above the surrounding
benchtop surface.
Flushmounting uses the same precut cavity but with a rebated edging
to allow the perimeter of the cooktop to ‘sink’ to a flush height with the
surrounding benchtop. This type of installation is applicable to stone
benches, such as marble and granite and the quartz resin benchtops.
POWER BOOST
The induction zone is selectable for power boosting its nominal
wattage. This power boosting effectively speeds heating-boiling time
by approximately twenty percent on an already very rapid time.
SAFETY
• the induction zone cooks no longer than factory programmed 90
minutes continuously;
• boilovers and boiling dry automatically switches off the cooktop;
• residual heat LEDs indicate any zone above 60ºC.
SIHP40WG4
smeg 40cm induction cooktop with wok recess
WARNING: technical specications and product sizes can be varied by the manufacturer
without notice. Cutouts for appliances should only be by physical product measurements.
The above information is indicative only.
PLEASE NOTE: drawings are not to scale. They are to assist only.
ID161012
Code SIHP40WG4
overall dimensions 400mmW x 520mmD x 131mmH
cutout for topmounting 365mmW x 465mmD
electricity supply 240 volts, 50 Hz
wattage 2300 watts
power boost 3000 watts
current 12.5 amps
electrical connection 15 amp rated power cord with 15 amp 3-pin
plug for direct plugging to a dedicated 15 amp
socket
OR
hard wired
(NB: cable and plug not supplied)
supplied accessory wok utensil, seal, instructions for
installation, operation, maintenance
NB: clips are not required for installation
packaged dimensions 590mm x 493mm x 195mm = 0.057m³
gross weight 14kg
net weight 13kg
400
>
<
16
>
<
4.36
>
<
12
75
131
>
<
>
<
40
30
230
electrical connection,
hard wired
347
520
400
V
V
V
V
93
113
314
<
50
314
PLAN
FRONT ELEVATION
electrical connection,
hard wired
215
>
>
30
> <10
>
<
10
>
>
40
>
< >
<
16
35
520
SIDE ELEVATION
Loading...