Smeg SGR30S Operating Instructions

SGR

3

0S

Betriebsanleitung

Operating Instructions

Istruzioni per l’uso

9.696.038

1

GB 1

SGR30S

Table of Contents

& ENGLISH

Contents Page 1 Table of contents 1 2 Introduction 2 3 Before Starting

Guide to these Operating Instructions 3 Intended Use 3 Set -Up and Function 4 Safety instructions 5 Installation 5 Start –Up 6

4 Basic Functions

Programming Aids 7 Configuration of the device 8 Configuration of the printer 8 Data Input 9 Activation of the printing data 10 Special functions 11 Operation and validation 12

5 Troubleshooting and Maintenance

Troubleshooting Chart 13 Customer Service 13 Maintenance Chart 15 Parts Service 15 Parts Required for Maintenance and Wear 16 Replacement parts 17 Part numbers 18

Maintenance Information

Replacing ink ribbon 19 Replacing Teflon strip on guide rail 20 Replacing Teflon strip for heating die 21 Replacing pressure roller 22

Setting 23 Adjustment

Service date 24 Standby function 24

Activate default settings function 24

6 Technical Data

Circuit and Wiring Diagram 230 V 25 Circuit and Wiring Diagram 115 V / 100 V 25 Specifications 26

9.696.038

ENGLISH

2

GB 2

SGR30S

Operating Instructions

Introduction

First we would like to thank you for purchasing the sealing machine. These instructions include information on the machine, its function and operation.

! Please read these operating instructions thoroughly before using the machine so that you will

be familiar with the capabilities of the machine and can utilize its features to the optimum.

FAlways keep these instructions in the vicinity of the machine.

Important note:

This device is a packaging machine for the processing of thermoplastic films and composite films according to the thermal – bonding or sealing process. In this respect , please pay attention to the “Intended use” chapter in the operating instructions.

According to the intended use , the CE symbol was affixed on the basis of the EU Directives named below: 89/336/EEC, 98/37/EC and 73/23EEC amended by 93/68EEC.

The 93/42EEC Directive is not applicable to bonding and sealing devices. The limit values stipulated in IEC 60601 – 1 cannot be applied in case of the electrical repetition tests.

The manufacturer will not assume any liability for damage caused by tests according to standards which are not listed in the declaration of Conformity .

Note Since we continuously improve our products we reserve all rights to modify these operating instructions and the functions described therein. We make all possible efforts to keep these instructions free of errors and complete. If you note any errors or unclear points please advise us.

9.696.038

ENGLISH

3

GB

3

SGR30S

Before Starting

Guide to these Operating Instructions

Before Starting

Basic Functions

Troubleshooting

and

Maintenance

Technical Data

Intended Use The machine is intended for commercial and industrial applications and should

be used only for the intended purpose. The machine is a sealing machine for sealing sterilization packages consisting of paper, paper laminate foil or Tyvek foil.

! It is not suitable for sealing pure polyethylene foils, soft PVC foils, hard PVC foils, polyamide foils or polypropylene foils. The machine capacity depends on the characteristics of the sealing material used.

This chapter contains information on the functions of the machine and instructions for handling and installation.

BE SURE TO READ!

Adjustment and operation of the machine are explained here.

Instructions for finding causes of malfunctions and eliminating them. This chapter includes information on the required maintenance, parts subject to wear and replacement parts.

Shows the interrelationship between various item numbers, the circuit and diagram plans and machine specifications.

9.696.038

ENGLISH

3

GB

4

SGR30S

Before Starting

Set-Up and Function

Power switch

Power fuse

Power connection

Peel edge adjustment 5 - 30 mm

Display

Input and function keys

Sealing and Printing Operation Sequence

1. After inserting the sterilization package switch on transport.

2. The sterilization package is then transported and the area of the sealing seam is heated to the sealing temperature set on the upper and lower heating dies.

3. The hot seam is presse d together by the sealing roller sealing it.

4. The printing operation is activated and the activated print data is printed onto the sealed package.

5. The finished sterilization package is transported to the discharge side.

6. If more packages to be sealed are not fed in the transport mechanism shuts off after

approx. 30 s.

9.696.038

ENGLISH

3

GB

5

•

Œ

SGR30S

Before Starting

General safety instructions

The device must not be installed or operated by persons under

14 years of age. The device must not be operated unattendedly.

Installation

Do not install or operate the machine in explosion hazard areas.

Set up the machine only in dry areas. Heavy dust, vapor, dripping or spraying water have a negative effect on the machine functions.

I

Turn of the device or disconnect the power cord when it is not in use. The device should only be cleaned with a dry or slightly damp cloth. Warning! Never clean the device wet!

Use only power sockets with protective ground.

Always ensure that the operating power corresponds to the specifications on the machine rating plate.

F Please choose a socket where the line power is stable.

Please do not transport device on the peel edge setting! Œ

Leave a gap of 200 mm between the device and the wall. •

200 mm

9.696.038

ENGLISH

3

D

EU

10-03-08 09:30

GB

6

SGR30S

Start-Up

Before Starting

l Plug power cable into power socket

on machine

l Insert plug into wall socket l Switch on machine

with power switch

FUNCTION DISPLAY

Machine switched on Self-test runs for approx. 30 s

Default settings When the device is switched on

for the very first time, the following defaults must be undertaken:

Language

also refer to page 8

Measurement unit

also refer to page 8

Date and time

also refer to page 9

Display for approx. 5 seconds: V069.A27 = Program version 440001 = Machine number

If maintenance deadline is exceeded

Acknowledge maintenance message

Perform maintenance

Display of date, time Actual temperature. Setemperature

After 5 minutes is the set temperature reached Machine is ready for operation

Please wait

set Language

Unit of measure

dd-mm-yy hh.mm

Control SGR30S V069.27

M A I N T E N A N C E

17-02-08 14:30 025°C

17-02-08 14:35 140°C

440001

Power switch

Switch connection

9.696.038

4

GB

7

ENGLISH

SGR30S

Basic Functions

Programming Aids

FUNCTION KEYS DISPLAY

INPUT AIDS Cursor control

Press - cursor right - key once

INPUT AIDS Changing numbers and Letters

Press key – position +1 - once

INPUT AIDS Return to previous menu point without activating entry

INPUT AIDS Activate input

Cursor Cursor

1x

left right

Position +1 Position -1

1x

100°C

5Cursor flashes at 1st digit

100°C

5Cursor flashes at 2nd digit

100°C

51st digit is number 1

200°C

51st digit is number 2

INPUT AIDS Space at selected point Set piece counter to 0

9.696.038

GB

0 - 99

C

4

GB

8

ENGLISH

SGR30S

Basic Functions

Configuration

FUNCTION KEYS DISPLAY

CONTRAST SETTING

DATA INPUT Selection: Language, symbols, temperature unit

Language: D, GB, F, E, I, SF, S, PL,CZ,TR

Symbols: yes/no

Temperature unit: C / F

è

Language selection

yes / no

Celsius / Fahrenheit

Contrast é

Contrast

display - contrast

set language

pictogramm NO

temperature unit

Printer Set-Up

FUNCTION KEYS DISPLAY

PRINTER SET UP

Printing direction 0° 180°

Start printing 0 - 99 mm

Character width 0 – 5

Character interval 0 – 5

è Yes / No

Input

0 / 180

Input Start printing

Input Character width

Input Character interval

printer set up YES

print out

0

distance

00 0-

character width

0 0-

character distance:

0 0-

9.696.038