Smeg SDO12-5, SDO8-5 User Manual
Contents
1. INSTRUCTIONS PROPER USE ___________________________________________ 4
2. SAFETY INSTRUCTION _________________________________________________ 5
3. KNOW YOUR OVEN ____________________________________________________ 6
4. BEFORE FIRST USE____________________________________________________ 6
5. ANALOGUE ELECTRONIC CLOCK (ON SOME MODELS ONLY) ________________ 7
6. ELECTRONIC PROGRAMMER (ON SOME MODELS ONLY)____________________ 9
7. OVEN CAVITY ________________________________________________________ 11
8. AVAILABLE ACCESSORIES_____________________________________________ 12
9. DESCRIPTION OF THE CONTROLS ON THE FRONT PANEL__________________ 13
10. COOKING FUNCTIONS ________________________________________________ 16
11. CLEANING AND MAINTENANCE _________________________________________ 20
12. SOMETHING WRONG? ________________________________________________ 23
13. INSTALLATION _______________________________________________________ 24
Thank you for choosing our product.
We advise you to read this manual carefully. It contains all necessary instructions for maintaining
unaltered the appearance and functional qualities of the hob.
INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the
correct procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must
install the appliance, set it functioning and carry out an inspection test.
3
Instructions for proper use
1. INSTRUCTIONS PROPER USE
ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTION FOR THE GAS
& ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS.
IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS APPLIANCES
BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE
RELEVANT STANDARDS AND REGULATIONS.
OUR APPROVED INSTALLERS GUARANTEE A SATISFACTORY JOB.
GAS OR ELECTRICAL APPLIANCES MUST ALWAYS BE DISCONNECTED BY SUITABLY
SKILLED PEOPLE.
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT
IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE
OVEN. WE ADVISE CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS
THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED
PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE.
THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING
AND HEATING-UP OF FOOD. ALL OTHER USES ARE CONSIDERED IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.
NEVER USE THIS APPLIANCE FOR HEATING ROOMS.
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS
WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION
CENTRE.
ALL THE APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE.
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS.
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS
POSITIONED VISIBLY ON THE OVEN DOOR FRAME.
DO NOT REMOVE THIS PLATE FOR ANY REASON.
THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL NOT BE USED AS A
SPACE HEATER.
TO PREVENT ANY STEAM IN THE OVEN CREATING PROBLEMS, OPEN
THE DOOR IN TWO STAGES: HALF OPEN (5 CM APPROX.) FOR 4-5
SECONDS AND THEN FULLY OPEN. TO ACCESS FOOD, ALWAYS LEAVE
THE DOOR OPEN AS SHORT A TIME AS POSSIBLE TO PREVENT THE
TEMPERATURE IN THE OVEN FROM FALLING AND RUINING THE FOOD.
The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance or by the use
of non-original spare parts.
4
Safety instruction
2. SAFETY INSTRUCTION
INSTRUCTIONS FOR THE INSTALLER: THESE ARE INTENDED FOR THE QUALIFIED
TECHNICIAN WHO MUST INSTALL THE APPLIANCE, SET IT FUNCTIONING AND CARRY OUT
AN INSPECTION TEST.
DO NOT ATTEMP TO MOVE THE APPLIANCE BY PULLING ON THE DOOR OF HANDLES. OPEN
THE DOOR AND GRASP THE FRAMES OF THE OVEN TAKING CARE THAT THE DOOR DOES
NOT SHUT ON YOUR FINGERS.
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE EARTHED ACCORDING TO THE
METHODS REQUIRED BY SAFETY RULES.
WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE
COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH
APPLICABLE REGULATIONS.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN.
NEVER UNPLUG BY PULLING ON THE CABLE.
ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) POSITION WHEN
YOU FINISH USING THE OVEN.
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY
LIGHTED AND CAUSE FIRES.
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH THE
HEATING ELEMENTS INSIDE THE OVEN. ALLOW SUFFICIENT TIME FOR THE APPLIANCE TO
COOL AFTER SWITCHING OFF. TO AVOID BURNS AND SCALDS CHILDREN SHOULD BE KEPT
AWAY
THE OVEN IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN TO GO NEAR OR
PLAY WITH IT. THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN EXPERIENCE IN
THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR INSTRUCTED
BY ADULTS OR PEOPLE RESPONSIBLE FOR THEIR SAFETY.
THE APPLIANCE BECOMES VERY HOT DURING USE. SUITABLE HEAT-PROOF GLOVES
SHOULD BE WORN FOR ALL OPERATIONS.
DURING COOKING, DO NOT COVER THE BOTTOM OF THE OVEN WITH ALUMINIUM, TIN FOIL
OR GREASEPROOF PAPER AND DO NOT PLACE PANS OR OVEN TRAYS ON IT AS THIS MAY
DAMAGE THE ENAMEL COATING.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE OVEN,
FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION,
DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE
CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE. ALL REPAIRS MUST BE CARRIED OUT BY AN
AUTHORISED TECHNICIAN OR AT AN AUTHORISED SERVICE CENTRE.
IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS A ROOM HEATER.
5
Instructions for the user
3. KNOW YOUR OVEN
FRONT CONTROL PANEL
OVEN CAVITY
OVEN FAN
OVEN LIGHT
OVEN DOOR
DOOR HANDLE
SHELF AND TRAY RUNNERS
COOLING SYSTEM
The appliance is equipped with 2 cooling fans which come into operation when
the oven is switched on. Operation of the fan generates a normal flow of air
which comes out at the bottom, in the centre of the front of the oven, and may
continue for a short time even after the oven is switched off.
4. BEFORE FIRST USE
Do not leave the packing in the home environment. Separate the various waste materials and take
them to the nearest special garbage collection centre.
Before using the oven for the first time, pre-heat it to maximum temperature long enough to burn any
manufacturing oily residues which could give the food unpleasant odours.
HOW TO PROCEED
Remove all the accessories from the inside of the oven.
Remove all removable labels and protective films from the outside and the inside of the oven.
To switch on the oven at first use or after a power black-out, simply press the programmer central key
for 1 / 2 seconds to enable cooking in the large oven. The small oven does not require any specific
switch-on procedures: simply turn the thermostat knob to any setting. Only the grill function requires
setting of its energy level control.
Set the function knobs on the symbol
and the thermostat knob to 250°C. For the small oven
simply turn the thermostat knob on the symbol
6
.
Instructions for the user
When the oven is used for the first time, or after an interruption in the electricity supply, the display
This function only activates the buzzer, without stopping cooking.
5. ANALOGUE ELECTRONIC CLOCK (ON SOME MODELS ONLY)
The instructions provided are valid solely for the large oven.
LIST OF FUNCTIONS
TIMER KEY
COOKING DURATION AND END KEY
TIME SETTING AND RESET
VALUE DECREASE KEY
VALUE INCREASE KEY
The buzzer that sounds at the end of each programming will be made up of 10 buzzes repeated 3
times at intervals of about 1 minute. This sequence can be stopped at any time by pressing any key.
5.1 Setting the time
flashes at regular intervals. Press the key
seconds; the current time can now be set. Press the value modification keys
decrease the setting by one minute for each pressure.
Press one of the two value modification keys until the current time appears. Five seconds after last
pressing the key, the clock will start from the set time.
5.2 Timer
- Press and the display will light up as shown in figure 1;
- Within 5 seconds press key
or to set the timer. Each time a key is
pressed, an outer segment representing 1 minute of cooking is lit or switched
off (figure 2 shows 1 hour and 10 minutes).
- Five seconds after last pressing the key the countdown begins, at the end of
which the buzzer activates.
- The current time can be viewed during the countdown by pressing key
press the key again to return to the timer display.
- At the end of the countdown the oven must be stopped manually by turning the
thermostat knob and the function selector knob to 0.
to stop the display flashing. Press key again for 2
or to increase or
once,
1
2
It is not possible to set a cooking time of more than 4 hours.
5.3 Programming
Cooking duration: the 2
nd
key can be pressed to set the cooking duration. Before it can be set, the
thermostat must be turned to the desired cooking temperature and the function selector knob to any
setting. To set the cooking duration, proceed as follows:
7
Instructions for the user
- Press key ; the pointer will go to position 12 and the adjacent symbol
will flash (Fig. 1).
- Use the
or key to set the cooking duration: each pressure on the
key adds 1 minute to the cooking duration, and every 12 minutes a new
inside segment will light up (figure 2 shows a cooking duration of 1 hour).
- Once the desired duration is obtained, cooking will start about 5 seconds
after the last pressure on
- The display will show the current time, represented by the constantly
illuminated segments, and the minutes left to the end of the cooking time,
or .
1
represented by the flashing segments (each flashing segment means 12
minutes of cooking time left).
- At the end of the cooking time the timer will switch the oven heating elements
off, the beeps will start to sound and the numbers on the dial will flash.
- The duration can also be reset by deleting the program selected: Press the
central key
to be manually switched off if the cooking operation is in progress.
for 2 seconds to cancel the set duration and the oven will have
2
Warning: it is not possible to set cooking durations of more than 12 hours.
Cooking start: as well as setting a cooking duration, the cooking start time can also be set (with a
maximum delay of 12 hours in relation to the current time). To set the cooking start/end time, proceed
as follows:
- Set the cooking duration as described in the previous point.
- Within 5 seconds of last pressing key
Symbol
will flash on the display together with the current time, with internal segments
illuminated to show the end of cooking time. Use keys
or , press key again to set the cooking end time.
or to set the cooking end time.
- 5 seconds after the last key is pressed, the display will show the current time and the cooking
start and end times, which will be represented by the illuminated inside segments. The display
segments will be constantly illuminated as long as the current time is not the same as the cooking
start time; as soon as the current time reaches the set starting time, all the inside segments will
start to flash, indicating that the oven has started cooking.
- At the end of the cooking time the timer will switch the oven heating elements off, the beeps will
start to sound and the numbers on the dial will flash.
- To delete the entire set program, hold down the central key
for 2 seconds; if cooking has
already started, the oven will have to be switched off manually.
- Here we can see a programming example: the current time is 7:06 and
cooking is programmed to start at 8.00 and end at 9.00.
- At 8 o'clock the inside segments between 8 and 9 will start to flash, while the
hours hand will remain still.
Warning: for the oven to start cooking operations after the programming procedures described above,
the thermostat and function selector knob must be correctly set to the desired temperature and
function.
8
5.4 Display brightness reduction
To reduce the energy consumption in stand-by, key
brightness. To restore the normal brightness, press
can be pressed to reduce the display
again.
Instructions for the user
When using the oven for the first time, or after a power failure, the display flashes regularly and
6. ELECTRONIC PROGRAMMER (ON SOME MODELS ONLY)
The programmer user instructions are valid only for the large oven.
LIST OF FUNCTIONS
TIMER KEY
COOKING DURATION KEY
END OF COOKING KEY
VALUE DECREASE KEY
VALUE INCREASE KEY
6.1 Clock adjustment
indicates
changes the time by 1 minute either up or down.
. Press the keys and at the same time the keys or : each single press
Before setting the programmer activate the desired function and temperature.
Use this setting to automatically start and stop the oven.
6.2 Semi-automatic cooking
Use this setting for automatic oven switch-off at the end of cooking time. By pressing key
display lights up, showing
set the cooking time.
Release key
together with symbols A and
to start the programmed cooking time count. The display will now show the right time
; keep the key pressed and at the same time, press keys or to
.
6.3 Automatic cooking
By pressing key
press keys
By pressing key
the same time, press keys
Release key
symbols A and
After set-up, to see the cooking time remaining, press the key ; to see the end of cooking time
press the key .
Set-up with incoherent values is logically prevented (e.g. the contrast between a cooking time and a
longer period will not be accepted by the programmer).
, the display lights up showing ; keep the key pressed and at the same time,
or to set the cooking time.
the sum of the right time + cooking time will appear; keep the key pressed and at
or to regulate the end of cooking time.
to start the programmed count and the display will show the right time together with
.
, the
9
Instructions for the user
When cooking is over, the oven will automatically switch off and, at the same time, an intermittent
With the program set, hold down the key of the function to be deleted, while at the same time going to
The cooking data entered can be changed at any time by keeping the function key pressed and at the
6.4 End of cooking
alarm will sound. After switching off the alarm, the display will once again show the right time together
with the symbol
, indicating that the oven has returned to manual operation mode.
6.5 Adjusting the buzzer volume
The buzzer volume can be varied (3 settings) while it is operating by pressing key
.
6.6 Stopping the buzzer
The buzzer stops automatically after seven minutes. It can be stopped manually by pressing keys
and
together.
6.7 Timer
The programmer can also be used as an ordinary timer. By pressing key
; keep the key pressed and at the same time press keys or . On releasing the key ,
programmed counting will begin and the display will show the current time and the symbol
After set-up, to see the remaining time, press the key .
Use as a minute counter does not interrupt functioning of the oven at the end of the programmed time.
, the display shows
.
6.8 Deleting the set data
the value
deletion of the duration as the end of cooking.
by pressing the value modification keys or . The programmer will interpret
6.9 Modifying the set data
same time adjusting the keys
or .
10
Loading...