Smeg SDO10 User Manual

Contents

Instructions proper use ___________________________________________________________________4

2. safety instruction________________________________________________________________________5

3. KNOW YOUR OVEN ____________________________________________________________________6

4. BEFORE FIRST USE ____________________________________________________________________6

5. Electronic Analogue Clock (only on some models) _____________________________________________7

6. Electronic Programmer (only on some models) ________________________________________________9

7. OVEN CAVITY ________________________________________________________________________11

8. AVAILABLE ACCESSORIES_____________________________________________________________12

9. Description of control on the front control panel _______________________________________________13

10. cooking function _______________________________________________________________________16

11. CLEANING AND MAINTENANCE _________________________________________________________20

12. SOMETHING WRONG?_________________________________________________________________23

13. INSTALLATION _______________________________________________________________________24

Thank you for choosing our product. We advise you to read this manual carefully. It contains all necessary instructions for maintaining unaltered the appearance and functional qualities of the hob.

INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test.

Instructions for proper use

1. INSTRUCTIONS PROPER USE

ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTION FOR THE GAS & ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS. IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS APPLIANCES BE INSTALLED AND SERVICE BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. CORGI REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS. DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED AOUT BY COMPETENT PERSON.

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE OVEN. WE ADVISE CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING

AND HEATING-UP OF FOOD. ALL OTHER USES ARE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.

NEVER USE THIS APPLIANCE FOR HEATING ROOMS.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE.

ALL THE APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE.

DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS.

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME.

THE PLATE MUST NOT BE REMOVED.

THIS APPLIANCE IS DESIGNED FOR COOKING FOOD AND IT SHALL NOT BE USED AS A SPACE HEATER.

TO PREVENT ANY STEAM IN THE OVEN CREATING PROBLEMS, OPEN THE DOOR IN TWO STAGES: HALF OPEN (5 CM APPROX.) FOR 4-5 SECONDS AND THEN FULLY OPEN. TO ACCESS FOOD, ALWAYS LEAVE THE DOOR OPEN AS SHORT A TIME AS POSSIBLE TO PREVENT THE TEMPERATURE IN THE OVEN FROM FALLING AND RUINING THE FOOD.

The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares.

Safety instruction

2. SAFETY INSTRUCTION

INSTRUCTIONS FOR THE INSTALLER: THESE ARE INTENDED FOR THE QUALIFIED TECHNICIAN WHO MUST INSTALL THE APPLIANCE, SET IT FUNCTIONING AND CARRY OUT AN INSPECTION TEST.

DO NOT ATTEMP TO MOVE THE APPLIANCE BY PULLING ON THE DOOR OF HANDLES. OPEN THE DOOR AND GRASP THE FRAMES OF THE OVEN TAKING CARE THAT THE DOOR DOES NOT SHUT ON YOUR FINGERS.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE EARTHED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS. THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN. NEVER UNPLUG BY PULLING ON THE CABLE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) POSITION WHEN YOU FINISH USING THE OVEN.

NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY LIGHTED AND CAUSE FIRES.

PARTS OF THE APPLIANCE MAY BE HOT DURING OR IMMEDIATELY AFTER USE. CARE SHOULD BE TAKEN TO AVOID TOUCHING HEATING ELEMENTS INSIDE THE OVEN. ALLOW SUFFICIENT TIME FOR THE APPLIANCE TO COOL AFTER SWITCHING OFF. TO AVOID BURNS AND SCALDS CHILDREN SHOULD BE KEPT AWAY

THE OVEN IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN TO GO NEAR OR PLAY WITH IT. IT’S NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT SUPERVISION.

THE APPLIANCE BECOMES VERY HOT DURING USE. SUITABLE HEAT-PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS.

DURING COOKING, DO NOT COVER THE BOTTOM OF THE OVEN WITH ALUMINIUM, TIN FOIL OR GREASEPROOF PAPER AND DO NOT PLACE PANS OR OVEN TRAYS ON IT AS THIS MAY DAMAGE THE ENAMEL COATING.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE OVEN, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE. ALL REPAIRS MUST BE CARRIED OUT BY AN AUTHORISED ENGINEER OR AT AN AUTHORISED SERVICE CENTRE.

WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL BE USED AS A SPACE HEATER.

NOT

Instructions for the user

3. KNOW YOUR OVEN

FRONT CONTROL PANEL

OVEN CAVITY

OVEN FAN

OVEN LIGHT

OVEN DOOR

DOOR HANDLE

OVEN GUIDE FOR SHELF AND PAN

COOLING SYSTEM

The appliance is equipped with 2 cooling fans which come into operation when

the oven is switched on. Operation of the fan generates a normal flow of air which comes out at the bottom, in the centre of the front of the oven, and may continue for a short time even after the oven is switched off.

4. BEFORE FIRST USE

Do not leave the packing in the home environment. Separate the various waste materials and take them to the nearest special garbage collection centre.

Before using the oven for the first time, pre-heat it to maximum temperature long enough to burn any manufacturing oily residues which could give the food a bad taste.

HOW TO PROCEED

Remove all the accessories from the inside of the oven. Remove all the removable label and any protective foils from the outside and the inside of the oven. To switch on the oven at first use or after a power black-out, simply press the programmer central key

for 1 / 2 seconds to enable cooking in the large oven. The small oven does not require any specific switch-on procedures: simply turn the thermostat knob to any setting. Only the grill function requires setting of its energy level control.

Set the function knobs on the symbol

and the thermostat knob to 250°C. For the small oven

simply turn the thermostat knob on the symbol

Instructions for the user

5. ELECTRONIC ANALOGUE CLOCK (ONLY ON SOME MODELS)

The programmer user instructions are valid only for the large oven.

LIST OF FUNCTIONS

MINUTE-MINDER BUTTON

AUTOMATIC LENGTH / SWITCH-OFF TIMING BUTTON

TIME SETTING AND RESET

VALUE DECREASE BUTTON

VALUE INCREASE BUTTON

5.1 Setting the time

When the oven is used for the first time, or after a power blackout, the display flashes on and off at

regular intervals. Press the current time. Press the value modification keys

key for 1/2 seconds to stop the display flashing and start setting of the

or to increase or decrease by one minute for each time a key is pressed. Press one of the two value modification keys until the current time appears. The clock will start from the time set 6/7 seconds after the last key is pressed.

At the end of each programmed cooking operation, the clock gives 8 beeps, repeated 3/4 times at intervals of about 1 and a half minutes. The beeps can be stopped at any moment by pressing any key.

5.2 Minute-minder

This function does not stop cooking but just triggers the beeps.

- When the

key is pressed the display illuminates, appearing as shown in

figure 1;

- Press the

Whenever a key is pressed, 1 outside segment, representing 1 cooking minute

or keys within 6/7 seconds to set the minute-minder.

will light up (figure 2 shows 10 cooking minutes).

- The countdown will start 6/7 seconds after the last key is pressed; at the end of

it, you will hear the beeps.

- During cooking with countdown, the current time can be displayed by pressing

the

key once; press again to return to the minute-minder display.

- At the end of the countdown, the oven has to be switched off by hand, by

turning the thermostat and the function selector to 0.

Instructions for the user

5.3 Programming

Cooking duration time: the 2 the thermostat to the cooking temperature of choice and the function selector knob to any setting. To set the cooking time, proceed as follows:

- Press the

key for 1/2 seconds; the pointer will move to position 12 (Fig. 1).

button can be used to set the cooking time. Before setting it, turn

- Use the

and keys to set the cooking time; whenever the key is

pressed, 1 minute will be added to the cooking time, and every 12 minutes a new inside segment will light up (figure 2 shows a cooking time of 1 hour).

- Once the required time has been set, cooking will start about 6 seconds after

the last time the

or . key is pressed.

- Once cooking has started, the display will show the current time, represented

by the constantly on segments, and the minutes left until cooking finishes, represented by the flashing segments (every flashing segments indicates 12 minutes of cooking time left).

- When the end of the cooking time is reached, the timer will switch off the oven

heating elements, the beeps will start and the numbers on the dial will flash.

- The cooking time can also be reset by deleting the program set; pressing the

central key

for 1 or 2 seconds will delete the time set and the oven will have

to be switched off by hand.

Caution: cooking times of more than 6 hours cannot be set. Cooking start: as well as setting a cooking duration time, the user can also set the cooking start time

(up to 12 hours after the current time). To set the cooking start/end time, proceed as follows.

- Set the cooking duration time as described in the previous point.

- Within 6/7 seconds after the last time the

or keys are pressed, press the key to set the

cooking start time. The display will show the current time with the inside segments indicating the cooking end time illuminated. Use the

and keys to set the cooking start time.

- 6/7 seconds after the last time a key is pressed, the display will show the current time and the

cooking start and end times, indicated by the illuminated inside segments. The segments on the display will be constantly on until the current time is the same as the cooking start time; as soon as the current time reaches the cooking start time set, all the inside segments will start to flash, indicating that the oven has started cooking.

- When the end of the cooking time is reached, the timer will switch off the oven heating elements,

the beeps will start and the numbers on the dial will flash.

- To reset the entire program set, keep the central key pressed for 1 or 2 seconds: if cooking

has already started the oven will have to be switched off by hand.

- The image on the right shows an example of programming: the current time is

7.06 and cooking is programmed to start at 8 o'clock and finish at 9.

- At 8 o'clock, the inside segments between 8 and 9 will start to flash and the hour pointer will remain still.

Caution: for the oven to start cooking after the programming procedure just described, the thermostat and function selector must be properly set on the temperature and function required.

5.4 "DEMO" Function

Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating

elements while leaving the other functions unchanged. To activate it, simply press the

, and

keys for 3/4 seconds. A confirmation beep will inform the user that the function is active. To

deactivate it, simply repeat the same procedure.

Instructions for the user

When using the oven for the first time, or after a power failure, the display flashes regularly and

6. ELECTRONIC PROGRAMMER (ONLY ON SOME MODELS)

The programmer user instructions are valid only for the large oven.

LIST OF FUNCTIONS

MINUTE-COUNTER KEY

COOKING TIME KEY

END-OF-COOKING KEY

DECREASE TIME KEY

INCREASE TIME KEY

6.1 Clock adjustment

indicates changes the time by 1 minute either up or down.

. Press the keys and at the same time the keys o : each single press

Before setting the programmer activate the desired function and temperature.

Use this setting to automatically start and stop the oven.

6.2 Semiautomatic cooking

Use this setting for automatic oven switch-off at the end of cooking time. By pressing key display lights up, showing

set the cooking time. Release key together with symbols A and

to start the programmed cooking time count. The display will now show the right time

; keep the key pressed and at the same time, press keys o to

6.3 Automatic cooking

By pressing key press keys By pressing key the same time, press keys Release key symbols A and

After set-up, to see the cooking time remaining, press the key ; to see the end of cooking time press the key .

Set-up with incoherent values is logically prevented (e.g. the contrast between a cooking time and a longer period will not be accepted by the programmer).

, the display lights up showing ; keep the key pressed and at the same time,

or to set the cooking time.

the sum of the right time + cooking time will appear; keep the key pressed and at

o to regulate the end of cooking time.

to start the programmed count and the display will show the right time together with

, the

Instructions for the user

When cooking is over, the oven will automatically switch off and, at the same time, an intermittent

The acoustic alarm has three different settings. These can be operated, while the alarm is sounding,

The alarm switches off automatically after seven minutes. They can be manually de-activated by

Once the programme has been set, keep the key of the function to be cancelled pressed, while at the

The cooking data entered can be changed at any time by keeping the function key pressed and at the

6.4 End of cooking

alarm will sound. After switching off the alarm, the display will once again show the right time together with the symbol

, indicating that the oven has returned to manual operation mode.

6.5 Adjusting alarm volume

by pressing key

6.6 Switching off the alarm

pressing the keys

and together.

6.7 Minute Counter

The programmer can also be used as a simple minute counter. By pressing key shows

, programmed counting will begin and the display will show the current time and the symbol .

After set-up, to see the remaining time, press the key . Use as a minute counter does not interrupt functioning of the oven at the end of the programmed time.

; keep the key pressed and at the same time press keys o . On releasing the key

, the display

6.8 Cancellation of set data

same time as end-of-cooking time by the programmer.

is reached by means of variation keys o . Time cancellation will be considered

6.9 Changing the set data

same time adjusting the keys

o .

+ 16 hidden pages